N97 restarts when connecting to PC via Mass Storag...

Hi guys,
My friend has a N97 and she changed the font using E:\Resource\Fonts\ folder method. The font was successfully changed; however, she didn't like it.
So she decided to change back the font, but whenever she connects the N97 to PC via "Mass Storage" mode, the phone restarts itself, and by that I mean EVERY SINGLE TIME it'll restart.
Therefore we tried "PC Suite" mode, but we're unable to make any changes to the Fonts folder (ie delete / rename / cut-paste).
I've also tried using X-plore, but whenever I try to delete the [s60snr.ttf/etc...] files, xplore will give me an error: "Can't Delete File: E:\Resource\Fonts". I'm sure that the file isn't in "read-only" if that helps anyone.
The fonts are stored in the 30gb internal memory inside the N97, so it's impossible to swap out the memory and delete on another phone/computer.
I appreciate any answers

Hi Guys,
I had same problem with my N97 mini. I do not have external memory card. I installed 'FONTS' in my mass memory. Font changed but if I connect my phone in mass storage mode, phone resets.
Here is what I did,
1. Copy all my data in PC using PC suit mode ( I suspect back utility will not work here because it will restore the back up including fonts folder in mass memory. I am not sure though). Also copy RESOURCE folder in your PC ( you can delete fonts folder in this copied folder in PC. I made a mistake of copying only RESOURCE folder you can copy all the folders from mass memory and restore it later.
2. disconnect the phone from PC
3. Open , Office --> File mgr. --> Mass Memory --> got to options --> Scroll down --> format mass memory.
That's it.
Your phone will be 'shut down' after formatting is completed.
Restart the phone connect it to PC suit. You might not be able to see mass memory. In that case connect it in ' mass memory' mode. You can find your phone is not resetting. Copy RESOURCE folder from PC with out fonts folder.
You may reinstall firmware and reinstall all the application you need.
It worked form me. Hope it works for you. Do it on your own risk. Do not forget to copy the data from mass memory.
You may find HARD RESET options (*#7370#) but it only resets your C drive and not F OR G Drive.
If you have installed Fonts in G (External memory). I guess you can just remove it from phone and remove the fonts folder easily. Just remove external memory use card reader to connect it to PC and remove.
CHEERS

Similar Messages

N97 restarts itself when connecting to PC via Mass...

Hi guys,
My friend has a N97 and she changed the font using E:\Resource\Fonts\ folder method. The font was successfully changed; however, she didn't like it.
So she decided to change back the font, but whenever she connects the N97 to PC via "Mass Storage" mode, the phone restarts itself, and by that I mean EVERY SINGLE TIME it'll restart.
Therefore we tried "PC Suite" mode, but we're unable to make any changes to the Fonts folder (ie delete / rename / cut-paste).
I've also tried using X-plore, but whenever I try to delete the [s60snr.ttf/etc...] files, xplore will give me an error: "Can't Delete File: E:\Resource\Fonts". I'm sure that the file isn't in "read-only" if that helps anyone.
The fonts are stored in the 30gb internal memory inside the N97, so it's impossible to swap out the memory and delete on another phone/computer.
I appreciate any answers

Hi Guys,
I had same problem with my N97 mini. I do not have external memory card. I installed 'FONTS' in my mass memory. Font changed but if I connect my phone in mass storage mode, phone resets.
Here is what I did,
1. Copy all my data in PC using PC suit mode ( I suspect back utility will not work here because it will restore the back up including fonts folder in mass memory. I am not sure though). Also copy RESOURCE folder in your PC ( you can delete fonts folder in this copied folder in PC. I made a mistake of copying only RESOURCE folder you can copy all the folders from mass memory and restore it later.
2. disconnect the phone from PC
3. Open , Office --> File mgr. --> Mass Memory --> got to options --> Scroll down --> format mass memory.
That's it.
Your phone will be 'shut down' after formatting is completed.
Restart the phone connect it to PC suit. You might not be able to see mass memory. In that case connect it in ' mass memory' mode. You can find your phone is not resetting. Copy RESOURCE folder from PC with out fonts folder.
You may reinstall firmware and reinstall all the application you need.
It worked form me. Hope it works for you. Do it on your own risk. Do not forget to copy the data from mass memory.
You may find HARD RESET options (*#7370#) but it only resets your C drive and not F OR G Drive.
If you have installed Fonts in G (External memory). I guess you can just remove it from phone and remove the fonts folder easily. Just remove external memory use card reader to connect it to PC and remove.
CHEERS

Ipad 3rd gen shows blank screen when connecting to projector via HDMI AV adapter. I have an ipad 2 that works perfectly. Projector is a Dukane ImagePro 8106HA. Only difference I see is that the ipad 3 owner has not updated to IOS 6. Any thoughts?

Ipad 3rd gen shows blank screen when connecting to projector via HDMI AV adapter. I have an ipad 2 that works perfectly. Projector is a Dukane ImagePro 8106HA. Only difference I see is that the ipad 3 owner has not updated to IOS 6. Any thoughts?

Ipad 3rd gen shows blank screen when connecting to projector via HDMI AV adapter. I have an ipad 2 that works perfectly. Projector is a Dukane ImagePro 8106HA. Only difference I see is that the ipad 3 owner has not updated to IOS 6. Any thoughts?

I cannot play music when connect to stereo via 30-pin connector. Help?

Since I first upgraded my iPod Touch 2nd Gen to iOS 4.x, I cannot play music when connect to external speakers via the 30-pin connector. I've tried several different speaker systems, but none work. My iPod freezes after making my song selection and doesn't do anything until after rebooting. Even then, it just goes through the same cycle if I select another song. My iPod is 100% functional until I try to plug it in to an external speaker system.
Keep in mind that it worked up until iOS 3.1.3.

Sounds like iOS 4 broke the compatibility with your accessory, something that sometimes happens with major OS changes. Your only hope is to see if the accessory manufacturer has an update to make it compatible with iOS 4, or downgrade your Touch back to 3.1.3.

J2EE Engine auto restart when connect J2ee Engine Visual Adminnistrator

Hi expert
I'm config BI and EP for SAP NetWare 7.0(2004)
After aply patch JSPM successful then J2ee often restart when I login Engine Visual Administrator
I check logfile
Nov 5, 2008 10:52:15 AM [1225857135537]:Error   : Thread[Thread-13,5,main]      com.sap.engine.services.rmi_p4:    com.sap.engine.services.rmi_p4.Parser newRequest MSG:The possible problem is that there is no correctly working server node available. Check your working servers
trace file
/usr/sap/BWQ/DVEBMGS02/j2ee/cluster/dispatcher/log/ defaultTrace.0.trc
#1.#001A64C962F2001800000006000061DE00045AC54F59B3DC#1225703393178#com.sap.engine.services.jmx.MBeanServerInvoker##com.sap.engine.services.jmx.MBeanServerInvoker#######OrderedChannel for http service##0#0#Warning#1#/System/Server#Java###JMX connector exception occurred while processing external JMX request [ JMX request (java) v1.0 len: 315 | src: cluster target-node: 28888700 req: invoke params-number: 4 params-bytes: 0 | :name=com.sap.portal.prt.bridge.service.mbeans.PRTMBeanRuntime,j2eeType=PRTBridge_JMX_SECTION,SAP_J2EEClusterNode=28888700,SAP_J2EECluster="" null null null ]
[EXCEPTION]
#1#com.sap.engine.services.jmx.exception.JmxConnectorException: Unable to de-serialize request parameters, message [ JMX request (java) v1.0 len: 315 | src: cluster target-node: 28888700 req: invoke params-number: 4 params-bytes: 0 | :name=com.sap.portal.prt.bridge.service.mbeans.PRTMBeanRuntime,j2eeType=PRTBridge_JMX_SECTION,SAP_J2EEClusterNode=28888700,SAP_J2EECluster="" null null null ]
        at com.sap.engine.services.jmx.RequestMessage.readParams(RequestMessage.java:537)
        at com.sap.engine.services.jmx.RequestMessage.getParams(RequestMessage.java:586)
        at com.sap.engine.services.jmx.MBeanServerInvoker.invokeMbs(MBeanServerInvoker.java:90)
        at com.sap.engine.services.jmx.JmxServiceConnectorServer.receiveWait(JmxServiceConnectorServer.java:172)
com.sap.engine.core.service630.context.cluster.message.MessageListenerWrapper.process(MessageListenerWrapper.java:81)
        at com.sap.engine.core.cluster.impl6.ms.MSListenerThread.run(MSListenerThread.java:47)
        at com.sap.engine.frame.core.thread.Task.run(Task.java:64)
        at com.sap.engine.core.thread.impl6.SingleThread.execute(SingleThread.java:80)
        at com.sap.engine.core.thread.impl6.SingleThread.run(SingleThread.java:150)
Caused by: javax.management.InstanceNotFoundException: MBean with name com.sap.default:name=com.sap.portal.prt.bridge.service.mbeans.PRTMBeanRuntime,j2eeType=PRTBridge_JMX_SECTION,SAP_J2EEClusterNode=28888700,SAP_J2EECluster=BWQ not found in repository
        at com.sap.pj.jmx.server.MBeanServerImpl.getClassLoaderFor(MBeanServerImpl.java:1408)
        at com.sap.pj.jmx.server.interceptor.MBeanServerWrapperInterceptor.getClassLoaderFor(MBeanServerWrapperInterceptor.java:455)
        at com.sap.engine.services.jmx.CompletionInterceptor.getClassLoaderFor(CompletionInterceptor.java:576)
[root@sapvs08 log]# pwd
/usr/sap/BWQ/DVEBMGS02/j2ee/cluster/server0/log
[root@sapvs08 log]#cat defaultTrace.12.trc
#1.#001A64C962F200720000042A0000586E00045AC496B6EC66#1225700295502#com.sap.engine.services.monitor.mbeans.Monitor#sap.com/irj#com.sap.engine.services.monitor.mbeans.Monitor#J2EE_GUEST#0##n/a##04c6a190a97f11dd99cf001a64c962f2#SAPEngine_Application_Thread[impl:3]_24##0#0#Error##Plain###Caller J2EE_GUEST not authorized, user J2EE_GUEST is not available from user management, reason: com.sap.security.api.NoSuchUserException:Connect to SAP gateway failed
Connect_PM TYPE=A ASHOST=localhost SYSNR=02 GWHOST=localhost GWSERV=sapgw02 PCS=1
LOCATION    CPIC (TCP/IP) on local host with Unicode
ERROR       partner '127.0.0.1:sapgw02' not reached
TIME        Mon Nov 3 15:18:15 2008
RELEASE     700
COMPONENT   NI (network interface)
VERSION     38
RC          -10
MODULE      nixxi.cpp
LINE        2823
DETAIL      NiPConnect2
SYSTEM CALL connect
ERRNO       111
ERRNO TEXT Connection refused
COUNTER     254
#1.#001A64C962F200720000042B0000586E00045AC496B6F426#1225700295504#System.err#sap.com/irj#System.err#J2EE_GUEST#0##n/a##04c6a190a97f11dd99cf001a64c962f2#SAPEngine_Application_Thread[impl:3]_24##0#0#Error##Plain###com.sap.engine.services.jmx.exception.JmxSecurityException: Caller J2EE_GUEST not authorized, user J2EE_GUEST is not available from user management, reason: com.sap.security.api.NoSuchUserException:Connect to SAP gateway failed
Connect_PM TYPE=A ASHOST=localhost SYSNR=02 GWHOST=localhost GWSERV=sapgw02 PCS=1
LOCATION    CPIC (TCP/IP) on local host with Unicode
ERROR       partner '127.0.0.1:sapgw02' not reached
TIME        Mon Nov 3 15:18:15 2008
RELEASE     700
COMPONENT   NI (network interface)
VERSION     38
RC          -10
MODULE      nixxi.cpp
LINE        2823
DETAIL      NiPConnect2
SYSTEM CALL connect
ERRNO       111
ERRNO TEXT Connection refused
COUNTER     254
        at com.sap.engine.services.jmx.auth.UmeAuthorization.checkMBeanPermission(UmeAuthorization.java:63
Please help me soon
Quang Le

Check this link and see if it helps,
http://help.sap.com/saphelp_nw04/helpdata/en/92/fa369fb68e004598f246494665a49e/frameset.htm
Sameer

Computer restarts when connecting ipod - please help!

Hey, I've recently bought a usb 2.0 card so i can connect my ipod via usb 2.0 as it will be faster than usb 1.1.
There is a slight problem however, almost every time i connect my ipod via the usb cable to this new usb 2.0 port, the computer restarts.
On the odd few occasions the computer hasn't restarted, my ipod has not been recognised in itunes or my computer.
I have tried connecting other things such as my phone and my old mp3 player to the new usb card and they work fine.
Is this a problem with my ipod or just the usb card?
Any help would be much appreciated!
Thanks alot.
Windows XP
Windows XP

I've had this problem and given the advice to others and it has worked for some. This isn't mentioned in any other advice that I can see but it is a simple check that you should do, not very technical either!
With your iPod plugged in to the computer, first go through the 5R's and other help topics to check the basics (new cable, different computer, different USB port etc.)
If no luck, check to see if your iPod exists in Device Manager as follows: right-click on My Computer, then click on Manage, then Device Manager, then expand the section called Disk Drives on the right hand side and see if the iPod is shown there, if it is, go on to the next stage.
In the same Computer Management box, click on Disk Management on the left hand side, after a few seconds a new box opens on the right and should show all of the disks on your computer including the iPod. Then right-click on the iPod information and it will give you an option to Change the drive letter or path....click on that and then select Change; select a new drive letter which is not already assigned to any other disc (I picked Z down the bottom), save that then exit and see if it works. Good luck!

Random restarts when connected to comp.

So this has been happening for a few months now.
I plug my iTouch 16gb (1st gen) into my Mac Mini. So I'll get the black screen with the battery indicator... then about half the time, the screen will shut off after three seconds of the battery display screen and restart. After it's done restarting, my battery level drops 1/3-1/2 of what it was before the restart (regardless of battery levels before hand). After these sudden restarts, a regular syncing (no new music or anything, just a sync/update of calendars, bookmarks, contacts, etc.) the iTouch will take around five minutes(!)
Now the iTouch will also randomly restart when I connect to my iBook. But it has never happened when I plug the iTouch into the USB power adapter (current model). I've tried using different USB cords, doesn't make a difference. I've connected other people's iTouches to computers, never replicated a restart. I've restored, restarted, etc. my iTouch who knows how many times, still get the restarts.
So I don't know, something wrong with my iTouch hardware wise?
Thanks!

This doesn't really help you but mine occasionally restarts when I plug it in to iTunes and so far I've not experienced any problems with my iPod or what's on it when it happens. Just thought you'd like to know you're not alone

I'm suddenly getting the kernel panic message and constant restarts when connected to the time machine wireless network. if is switch to the BT network, all fine. no help found so far as to what's wrong or how to correct, anyone have any thoughts...

Recently upgraded to mountain lion in order to buy the new tall tower for time machine backups. had to get technical support to help with set up as it wouldn't play ball with two computers. all working fine up until last week when the iMac started getting backup error messages. then system restarts independently when using time machine on the time machine wireless network. only stops restarting when I switch the wireless network back to he bt one, which is a pain obviously as can't back up to time machine then. it has to be a problem with airport utility or something wireless but all says all up to date with software etc. all still works fine backing up from laptop on the wireless network, just the iMac is not happy. any help or thoughts very much appreciated.

Hi, many thanks Bob, what you say is not unthinkable at all, although it does answer the question
"what could I do *instead* of ..." rather than the one I actually asked, but seriously ...
Shutting down might be an answer, although it would clear out my tmp directory - which I might not want to have to sort through looking for things I want to save every time I go to work, and also, now that nvram doesn't seem to work for disabling the boot chime, it can get a bit embarassing booting up in a busy meeting if I have forgotten to mute before I shut down. There are all sorts of other issues, such as editing documents, loading web pages and so on that I would have to set up again.
Your suggestion of letting Apple know is a good one - thank you for the link.
Take care,
Mark

My ipod and also ipad will not sync or be recognised by itune on my windows xp computer when connecting the chord via usb

My ipod touch and also ipad is not coming up or showing when connecting to my computer and hence cannot sync it. The last available sync was about a week ago. Any ideas on what is not happening?

See:
iOS: Device not recognized in iTunes for Windows

Nokia N97 - Restart when I swip for unlocke and an...

Hello everybody. I need a help. My cellphone restart when I swip it for unlock or answer a call. What Should I do. Who can help me?

Try using a different theme (preferably Nokia default..).. If the problem persisits...a Soft Reset by dialing *#7370# followed by security code 12345 (default) or the one you have set.. may resolve the issue.. but take a back-up of your data before doing it as the reset will earase data from your phone..
--------------------------------------------------------------------------------------------------------------------------------------------------------------If you find this helpful, pl. hit the White Star in Green Box...

ICS - Live With Walkman - Can't connect USB in MSC (Mass Storage) mode

Hi Guys n Girls,
I recently updated my LWW to ICS and I can't for the life of me get the phone connect to my PC in MSC, mass storage mode.
Can anyone help?
Thank you.

This question seems "answered" without an answer actually being there? I see the same problem - connecting the phone to my (Ubuntu/Linux) machine before (running GB) ended up in the phone (SD card) being mounted as external USB storage device just as one would except. With ICS, this doesn't seem to work out of the box anymore, but unfortunately so far I also didn't manage to change this behaviour. Any hints on that?
TIA and all the best,
Kristian

N97 Errors when connecting via mini usb

Hey All,
I am a happy new owner of an N97, it took alot to leave my normal HTC and HP iPaq but i love the N97.
Except one little thing, i am unable to connect my phone to the PC suite via USB.
when i connect the phone it does give me the option to select PC Suite and i choose it but Nokia PC synch and Ovi Suite says the phone is not connected!
please can someone help??
Solved!
Go to Solution.

An alternative to PC Suite is to use Nokia's Ovi Suite 2. There is a recently released beta available from Nokia's Beta Labs. It's a much nicer interface and everything is integrated into one interface instead of a mish-mash of bits and pieces that form PC Suite.
http://betalabs.nokia.com/ovisuite
Ovi Suite 2 has been a lot less problematic for me. When it goes from Beta to Final release, Nokia will be getting rid of PC Suite anyway so you'll already be familiar with the software when it's the only offering from Nokia.
Message Edited by matt_t on 08-Oct-2009 11:13 AM
Nokia N8 on O2-UK
Firmware 022.014

Dell U2711 black screen when connected to Mac via DisplayPort

I currently have a Dell U2711 27" monitor connected to my Mac Mini through DVI (it uses a DVI to mini-DVI adapter at the PC end). However, I cannot get the full resolution of the monitor 1920 x 1080 maximum is offered were the monitors maximum resolution is 2560 x 1440.
I did some Googling and seemed it required DisplayPort connection to achieve this. No dramas. I ordered a Mini-DisplayPort to DisplayPort cable.
I plugged this in and all I get on the Dell is a black screen. The monitor doesn't go into power save mode or anything like that, just displays nothing - an illuminated black screen.
I pulled out my MacBook and connected the cable to that, same deal. The Mac recognises that the cable has been connected (as the laptops LCD goes blue for a second or two while it detects the new monitor).
Any ideas?
I also had a DisplayPort to DisplayPort cable here which was included with the monitor from Dell, which I will test aswell when my miniDisplayPort to DisplayPort adapter arrived.

Yes, that is one means, but...
However, HDMI 1.3 can also carry resolutions higher than 1920 x 1080 - check out http://en.wikipedia.org/wiki/HDMI - not really an option on the Dell monitor though, as it only supports up to 1080p on the HDMI connection. However, there is a thread elsewhere on the internet of a user who forced his Windows laptop to use 2560 x 1440 resolution via the HDMI output and the Dell monitor accepted it!
In addition, so can DisplayPort - as per my original post.
The Apple Dual-Link DVI adapter is plagued with issues and has a lot of faults, so I'd rather avoid it. It is also significantly higher priced than the above option of DP.

FME freezes when connecting Canon HV20 via firewire

Hoping someone can help me out. I'm using a Canon HV20 camera
as a live video stream via FME and every time I try FME will freeze
and my laptop will freeze and I have to restart. My camera settings
are DV standard and it should work.
The necessary drivers for the Canon HV20 are installed and
I'm using a firewire card in my PC laptop that to connect the
camera feed. Restarting several times still results in the same
problems.
Is there something I should modify/check on my system to
ensure it's working correctly?

Some more troubleshooting tips.
Cheers
Eddie
Forum FAQ
Premiere Pro Wiki
- Over 250 frequently answered questions
- Over 100 free tutorials
- Maintained by editors like
you

Static when connecting to hifi via headphone socket.

When I connect my Macbook Pro to a hifi with a phono to 3.5 cable via the headphone socket, I get a horrible hissing.
This only happens when my Macbook is plugged in, and it is even louder than the sounds it should be producing. Like if I'm playing a song in iTunes at full volume, and then connect it to the hifi, the hissing would be several times louder than the music playing.
It doesn't happen when I unplug the power adaptor.
I have tried it with numerous 3.5-phono cables with the same outcome, and I've used various other sources instead of the macbook such as iPod/cd players and they all play fine.
Anyone know what can be done about this?
I have PC speakers which work fine with it.
Also recently my headphone socket seems a lot more...delicate (I haven't slept in a while and can't think of the word - sorry).
Basically when I first got my mbp it was fine, but now if whatever is being plugged into the socket is nudged slightly, it will cut out temporarily. This happens regardless of what is being plugged in.
Thanks

I also have a macbook pro and an Apple Hi Fi. For one thing, you have to baby the Hi Fi, they can be pretty finicky and delicate and it doesn't take much for them to malfunction which I believe is part of the reason that Apple discontinued them. I also use a 3.5mm jack- 3.5mm jack to connect my macbook pro to my hifi and have no issues. Now what it sounds like is going on is that the issue is on the Macbook Pro side of things. How old is your MBP? Is there any light emitting from the audio jack on the laptop, as that can be an indicator of trouble. I get that hissing sound too so I'm pretty sure I know what yours is caused by. Basically, when a 3.5mm audio cord is plugged into the Hi Fi on one end but not properly into something at the other end, and the unplugged (or partially plugged) cord touches something else conductive/metal it will hiss really loudly. This should only occur when the Hi Fi's volume is turned up. Have you checked any other devices (output) like another speaker if possible to see if your mac's audio out port (the one with the headphone icon on it) is broken or malfunctioning. I am using a Belkin 3.5mm-3.5mm audio cord and it works well. So I'm guessing the issue is your audio-out but if all else fails it is possible to connect a macbook pro to a Hi Fi with a Toslink fiber optic cord. I don't know why this would fix the problem but if you truly have no issues with any other input to the hi fi and you have tried multiple audio cords (when audio cords get worn in my experience they will cause problems too, but that problem would likely present as getting single-channel audio interference (which would sound like listening to an ipod with headphone) then maybe a digital audio cord is the way to go. On top of that, a digital audio cord would dramatically improve the volume and sound quality (its roughly the difference in sound between listening to music on a docked ipod vs. plugging an ipod in via the audio out auxiliary jack). But, I would say your likeliest problem is the connection between the audio cord and the audio out port on the macbook pro. Hope this all helps!

N97 restarts when connecting to PC via Mass Storag...

Similar Messages

Maybe you are looking for