Nal.db error
Hi,
I restarted my ZfD 4 (NW6.5) server today, and it isn't happy with the
nal.db database. There's plenty of space on the volume, so I'm not sure
what's bugging it.... any ideas?
Thanks,
Iain
This server is licensed to:
Novell Inc.,
Novell Inc.,
Attempting to allocate cache of 32770K
32768K of memory used for caching
Using a maximum page size of 2048 bytes
Starting database "mgmtdb" (ZEN:\ZENworks\Inv\DB\mgmtdb.db) at Tue Feb 05
2008 1
4:12
Database recovery in progress
Last checkpoint at Fri Jan 11 2008 14:18
Checkpoint log...
Starting database "nal" (ZEN:\ZENworks\NAL\DB\nal.db) at Tue Feb 05 2008
14:12
Database recovery in progress
Last checkpoint at Fri Jan 11 2008 13:56
Checkpoint log...
Transaction log: nal.log...
Rollback log...
Checkpointing...
Starting checkpoint of "nal" (nal.db) at Tue Feb 05 2008 14:12
Transaction log: mgmtdb.log...
Unable to write to disk, error code 17
Fatal error: cannot write to transaction log
<Press any key to close screen>
I think I've fixed it... I copied the blank nal.db from the original install
CD, as suggested by TID 10092575.
"Iain McLaren" <[email protected]> wrote in
message news:zs_pj.29637$[email protected] ..
> Hi,
>
> I restarted my ZfD 4 (NW6.5) server today, and it isn't happy with the
> nal.db database. There's plenty of space on the volume, so I'm not sure
> what's bugging it.... any ideas?
>
> Thanks,
>
> Iain
>
> This server is licensed to:
> Novell Inc.,
> Novell Inc.,
> Attempting to allocate cache of 32770K
> 32768K of memory used for caching
> Using a maximum page size of 2048 bytes
> Starting database "mgmtdb" (ZEN:\ZENworks\Inv\DB\mgmtdb.db) at Tue Feb 05
> 2008 1
> 4:12
> Database recovery in progress
> Last checkpoint at Fri Jan 11 2008 14:18
> Checkpoint log...
> Starting database "nal" (ZEN:\ZENworks\NAL\DB\nal.db) at Tue Feb 05 2008
> 14:12
> Database recovery in progress
> Last checkpoint at Fri Jan 11 2008 13:56
> Checkpoint log...
> Transaction log: nal.log...
> Rollback log...
> Checkpointing...
> Starting checkpoint of "nal" (nal.db) at Tue Feb 05 2008 14:12
> Transaction log: mgmtdb.log...
> Unable to write to disk, error code 17
> Fatal error: cannot write to transaction log
>
>
> <Press any key to close screen>
>
Similar Messages
-
Hi there,
I am running Zenworks 3.2 and am having the following problem with NAL
launching on our Windows 2000 Terminal server. Whenever I log in on a
terminal session I get the error "Application Launcher Results from service:
Error loading NALUPDTE.DLL" and NAL fails to launch. The strange thing is if
I sit on the console NAL runs fine. Also we do not get the same problem with
our Windows 2003 servers.
Does anyone know what the problem is here and how I can go about fixing it.
Cheers.
Phill.Let me know if that does not work.
Phill Harvey-Smith wrote:
> Craig Wilson <[email protected]> wrote in
> news:[email protected]:
>
> > Phill Harvey-Smith wrote:
> >
> >> Hi there,
> >>
> >> I am running Zenworks 3.2 and am having the following problem with NAL
> >> launching on our Windows 2000 Terminal server. Whenever I log in on a
> >> terminal session I get the error "Application Launcher Results from
> >> service: Error loading NALUPDTE.DLL" and NAL fails to launch. The
> >> strange thing is if I sit on the console NAL runs fine. Also we do not
> >> get the same problem with our Windows 2003 servers.
> >>
> >> Does anyone know what the problem is here and how I can go about
> >> fixing it.
> >
> > http://support.novell.com/cgi-bin/se...?/10088446.htm
> > lists two possible solutions.
>
> Thanks for the reply. Though I don't think this is the problem as all our
> users are in the administrators group. The odd thing is that if I run
> nalwin32 manually that works fine, and a user can run applications, I may
> just modify the login script so that it just launches nalwin32 when logging
> into this server.
>
> Phill. -
NAL application error (id=-337)
Hi,
I try to distribute some applications (i.e. patches for WinXP, AcrobatReader6 etc.).
On many workstations the applications are running without problems.
But on some workstations I get an error message:
Could not get needed resources for application [***] to be launched (id=-337)
Problem: Unable to connect to server [***]
I searched in the KB whitout success.
Can someone help me?Build a test object that runs CMD.EXE as an Unsecure System User.
Run this object on a problem machine.
From the CMD prompt that this app opens run "start \\SERVER\VOL\DIR" for the UNC patch to
the install source.
I suspect this will give you an error.
If an error occurs, then SYSTEM app, which get their network FileAccess rights from the
WSOBJECT, do not have proper rights.
In your case, I would try "Unreg32",Delete the WSObject in the NDS, followed by WSREG32 to
reimport the WSOBJECT.
Some type of corruption may have occurred.
I've seen this happen on occassion with ZFD3.x.
(Note: Make sure you are using UNC and not mapped drives as mapped drives will not work
easily with XP and System Apps.)
"Arthur R." wrote:
> > Are you running the app as an Unsecure System App?
>
> Yes.
>
> > If so make sure the Workstation Mgr service is running and the PC has a valid
> > workstation object.
>
> Workstation Mgr is runnig and the PC is as valid workstation object imported.
> WS: WinXP SP1a with NW4.9SP1b
>
> Amusing is that this message did not come on some workstations and suddenly emerges now.
Craig Wilson
CNE3, 4, 5 - MCSE - CCNA
NSC Sysop (http://support.novell.com/forums/)
Tech Writer - http://www.ithowto.com
(I Peter 4:10) -
ZESM Client XP3 Zenworks 7 NAL
We've experiencing issues since deployment of the ZESM client onto a clean
set of Windows XP Pro SP3 HP xw4600 into a non-domain environment with ZESM
in standalone mode.
The workstations have Client32 4.91 SP5 and ZenWorks Agent 7.0.1.0. We have
two ZESM polices, one with no CD, USB access and one with CD and USB access.
On both of the policies the firewall is set to all ports open.
When a user logins to a machine one of the following can happen.
1) During the stage that NALWIN launches, applications start to deploy as
set because of force run, however during this NAL will error with
Could not configure workstation for application [Novell eDirectory
Application Object full context] (id=34822) Problem: Unable to access needed
network resource [App:INI Settings]. (D0:E)
Or other errors relating to accessing eDirectory attributes. At this point
the workstation is now broken, if a user tries to refesh NAL then all the
icons will disappear.
2) On the odd time, the login script will error with drive mappings and the
error code:
3) The workstations suffers a "Windows - Delayed Write Failed", Windows was
unable to save all the data for the file
C:\............................................... ................. The data
has been lost. This error may be caused by a failure of your computer
hardware or network connection. Please try to save this file elsewhere.
This fault intermittent but happening during the day across the batch of 24
workstations.
The .sen policies are delivered via NAL, it appears to be linked to a change
of policy but this is not always the case. It also looks like a timing
issue/issue with ZESM blocking network for a few sec.
On machines which lose their apps, you can still access the network shares,
and in Novell Connections it still shows the attached servers.
We have a Service Request: 10496360551 with Novell, but just wondering if
anyone has seen this issue or had any ideas. This is service affecting.
On the SR it has our .sen and some debugging information from ZESM and NAL.
Regards
AdamAdam,
I haven't used the ZESM client jointly with the ZDM7 agent. However, I have some comments:
- Are you using the latest IR6 ZESM client?
- Why are you deploying two policies to the endpoints? Only one policy can be applied to a given client at a time. No merge or inheritance can happen. You can, however, define multiple locations with multiple Storage Controls on it.
- Have you tried using the ZSC client in a managed (ZESM server) scenario?
I may recommend you to also post this question to the ZDM7 support forum (if not already done), since the error messages you posted are more related to NAL/ZDM than to ZESM. Maybe someone can help you a bit more on this issue.
Cheers,
Daniel
>>>
From: Adam Shailes<[email protected]>
To:novell.support.zenworks.endpoint-security-management
Date: 5/21/2009 8:44 AM
Subject: ZESM Client XP3 Zenworks 7 NAL
We've experiencing issues since deployment of the ZESM client onto a clean
set of Windows XP Pro SP3 HP xw4600 into a non-domain environment with ZESM
in standalone mode.
The workstations have Client32 4.91 SP5 and ZenWorks Agent 7.0.1.0. We have
two ZESM polices, one with no CD, USB access and one with CD and USB access.
On both of the policies the firewall is set to all ports open.
When a user logins to a machine one of the following can happen.
1) During the stage that NALWIN launches, applications start to deploy as
set because of force run, however during this NAL will error with
Could not configure workstation for application [Novell eDirectory
Application Object full context] (id=34822) Problem: Unable to access needed
network resource [App:INI Settings]. (D0:E)
Or other errors relating to accessing eDirectory attributes. At this point
the workstation is now broken, if a user tries to refesh NAL then all the
icons will disappear.
2) On the odd time, the login script will error with drive mappings and the
error code:
3) The workstations suffers a "Windows - Delayed Write Failed", Windows was
unable to save all the data for the file
C:\............................................... ................. The data
has been lost. This error may be caused by a failure of your computer
hardware or network connection. Please try to save this file elsewhere.
This fault intermittent but happening during the day across the batch of 24
workstations.
The .sen policies are delivered via NAL, it appears to be linked to a change
of policy but this is not always the case. It also looks like a timing
issue/issue with ZESM blocking network for a few sec.
On machines which lose their apps, you can still access the network shares,
and in Novell Connections it still shows the attached servers.
We have a Service Request: 10496360551 with Novell, but just wondering if
anyone has seen this issue or had any ideas. This is service affecting.
On the SR it has our .sen and some debugging information from ZESM and NAL.
Regards
Adam -
Error 501b Loadlibrary msvcrt.dll failed
We have Netware 5.1, Zenworks 3 and a mixture of Win2k and Win98
workstations.
When running NAL at one of our sites it comes up with the following error
which has to be OK'd before it will load the NAL.
"Error 501b Loadlibrary msvcrt.dll failed"
The user has read and file scan rights to sys:public
The server has msvcrt.dll version 5.0.0.7022
and the PC has msvcrt.dll version 6.1.9844.0
Does anyone know how to get rid of the error message?
(Some of the files in the public directory were missing, so I have copied
in nal*.* and zen*.* Does it need anything else?)
ThanksDLLs are normally backwards compatible.
Therefore I would try renaming the version in PUBLIC and replacing it with
the newer version from the PC.
Sounds like perhaps an older one if being used instead of the newer one.
[email protected] wrote:
> We have Netware 5.1, Zenworks 3 and a mixture of Win2k and Win98
> workstations.
>
> When running NAL at one of our sites it comes up with the following error
> which has to be OK'd before it will load the NAL.
>
> "Error 501b Loadlibrary msvcrt.dll failed"
>
> The user has read and file scan rights to sys:public
>
> The server has msvcrt.dll version 5.0.0.7022
> and the PC has msvcrt.dll version 6.1.9844.0
>
> Does anyone know how to get rid of the error message?
>
> (Some of the files in the public directory were missing, so I have copied
> in nal*.* and zen*.* Does it need anything else?)
>
> Thanks
Craig Wilson
CNE3, 4, 5 - MCSE - CCNA
NSC Sysop (http://support.novell.com/forums/)
Tech Writer - http://www.ithowto.com
(I Peter 4:10) -
Adding Distribution Point - 2147942405: Access is denied.
I'm trying to add a Distribution Point on a new site server but I'm getting the error: 2147942405: Access is denied. in the component manager.
I have the site server's computer account in the administrators group on the remote DP and I have restarted the server since doing so.
The problem is definitely not network / firewall related because if I choose to use my own crednetials to install the role it goes through OK (although this then causes other errors!)
Any ideas why I am getting access denied error?
ThanksPolling server CRWNBDP1... SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
Installing server... SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
Attempting to obtain an IAbstractNetwork interface from NAL... SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Call to the Abnetwork DLL's DllGetClassObject function succeeded. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Provider list is not initialized, initializing... SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - The 'Operational Active Order' list has 2 values, trying to enumerate them (in reverse order)... SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Attempting to use provider MSWNET. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - This provider's CLSID = {8EEC6CB7-04A9-11D1-8428-08002BE5FB88}. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Checking if this provider has a registered DLL. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Got the path to this provider's DLL: C:\Program Files\Microsoft Configuration Manager\bin\i386\mslmsvrn.dll. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - This provider has a registered DLL. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Call to NAL's MS LANMAN DLL's DllGetClassObject function succeeded. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Attempting to construct MS LANMAN Provider object ... SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Successfully constructed MS LANMAN Provider object. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Provider 'MSWNET' inserted into list. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Attempting to use provider LOCAL. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - This provider's CLSID = {8EEC6CAF-04A9-11D1-8428-08002BE5FB88}. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Checking if this provider has a registered DLL. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Got the path to this provider's DLL: C:\Program Files\Microsoft Configuration Manager\bin\i386\falsvrn.dll. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - This provider has a registered DLL. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Call to the FAL DLL's DllGetClassObject function succeeded. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Attempting to construct FAL Provider object ... SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Successfully constructed FAL Provider object. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Provider 'LOCAL' inserted into list. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Provider 'ABEXPRT' inserted into list. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
Successfully obtained the IAbstractNetwork interface. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
Attempting to call IAbstractNetwork::CreatePath() with NAL path "MSWNET:\\CRWNBDP1\admin$\"... SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Attempting to create path for MSWNET:\\CRWNBDP1\admin$\. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[2] - CreatePath, wrong provider: ABEXPRT. Trying next provider... SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[2] - CreatePath, wrong provider: LOCAL. Trying next provider... SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - CreatePath, MSWNET is the correct provider. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Provider MSWNET successfully got objects for path MSWNET:\\CRWNBDP1\admin$\. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Successfully created the path: MSWNET:\\CRWNBDP1\admin$\. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
Successfully called IAbstractNetwork::CreatePath() with NAL path "MSWNET:\\CRWNBDP1\admin$\". SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
Attempting to obtain an INetworkObject interface from NAL for this server... SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
Successfully obtained the INetworkObject interface. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
Testing connectivity to this server using NAL INetworkObject::IsAccessible()... SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - An admin rights connection is being requested to the share ADMIN$. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Attempting to get access for this path ... SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - This thread of the process can now proceed with its attempt to get access. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Attempting to capture ownership of 'SMS NAL Try Access Mutex'. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Creating/getting handle to 'SMS NAL Try Access Mutex'. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Waiting up to 180000 milliseconds for ownership of 'SMS NAL Try Access Mutex'. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Successfully captured ownership of 'SMS NAL Try Access Mutex' (handle = 358). SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Successfully captured ownership of Try Access mutex. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Checking for existing access ... SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Checking if currently connected ... SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Has this object previously obtained a deviceless connection ... SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - It has not. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[2] - WARNING: Try() failed. This network connection does not exist. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Recoverable error: This network connection does not exist. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - This platform supports the application of network connection accounts on a per-site basis. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[4] - Call to the Abnetwork DLL's DllGetClassObject function succeeded. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:20 1692 (0x069C)
NAL[2] - WARNING: failed to get the site code from the path. Unspecified error SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Got the site code from the Site Code value. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Successfully got the primary site code SU1 from the registry. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Attempting access using the network accounts available for this site ... SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Attempting to get the net connect account list for site SU1 from the registry. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Successfully got the net connect account list. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[2] - WARNING: the network connect account list is empty. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[2] - WARNING: TryEachInList() failed. Unspecified error SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Recoverable error: Unspecified error SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Attempting access under the context of the current process ... SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Attempting to connect using the Access interface. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Applying default account (user name and password are both null). SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Attempting to access with default user/password SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Checking if NAL server-path '\\CRWNBDP1\admin$\' is local machine SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - NAL server-path is NOT local machine SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Checking if the current user logged on locally. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - The current user is the LocalSystem, assuming the it is not only known locally. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Attempting to release current connection. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - A deviceless connection has not yet been made. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Attempting to add connection to
\\CRWNBDP1\admin$. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Current user context = SYSTEM. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Attempting to get provider name for a specified network type by calling WNetGetProviderName. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - The network provider name for MS LANMAN is Microsoft Windows Network. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Call to the Abnetwork DLL's DllGetClassObject function succeeded. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[2] - Provider list is already initialized. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Waiting up to 2 minutes for ownership of Connection Arbiter. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Successfully captured ownership of Connection Arbiter. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Attempting to register MSWNET:\\CRWNBDP1\admin$\ SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Checking if the resource is currently connected ... SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Checking if a deviceless connection has been made to this path:
\\CRWNBDP1\admin$. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Checking status for connection:
\\CRWNBDP1\admin$. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - NetUseGetInfo DID NOT report status. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[1] - ERROR: failed to get connection status. This network connection does not exist. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[2] - The resource is not currently connected. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[2] - Resource is not currently connected. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Persistance = 0, Reference Count = 0. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Persistance = 0, Reference Count = 0. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Current Persistance = 0, Reference Count = 0. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - New Persistance = 0, Reference Count = 1. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Persistance = 0, Reference Count = 1. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Resource does not currently exist. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Successfully registered the connection with Connection Arbiter. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Resource will now be under arbitration. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Attempting to establish a new connection. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - GetAccess for PATH: \\CRWNBDP1\admin$ SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C)
NAL[4] - Using current user context. SMS_SITE_COMPONENT_MANAGER 03/11/2011 14:54:21 1692 (0x069C) -
Hi,
I have an issue I am not able to solve.
When configuring a pro email in the advanced menu, I have the below error message :
Invalid\escape: line 1 column 271 (char 271).
I have checked the email information (server adress, password and so on), everything is fine...
Cannot find the meaning of the message error.
Thanks a lot for your help.
RegardsHi..
For Work Account ::
User ID : Email Adress ( [email protected])
Activation Password : Provided from the IT Admin
Server Adress : provided by It Admin ( S3459908)
For Microsoft Exchange ActiveSync
Description : Your Desired Name (eg. Your Company name)
Domain : Your Organizatin Domain name
Username: Credentials of your Account
Email Address: Your Email Address
Password: Password for the Email
Server Adress: Provided by the IT Admin
Port: Provided by the IT admin
Use SSL : ON/OFF as per your IT Admin..
Please feedback me in this regard...
Thanks..
Please update the result after applied..
Thanks -
Writing error file from app server to windows serevr in background job
Hi Gurus!
I have a program that runs in the background and updates or uploads or inserts the tables with data in background and generates an error log . I would like to write this file on the windows serevr from the application serevr during the run of the program itself automatically. I tried running several jobs with my program but its not writing to the windows serevr , it writes on the application and then stops . Is theer a fault in my coding above.
form write_err_file .
IF v_zss = 1.
case p_as.
when 'X'. "X is application server
case sy-sysid.
when 'DEV' or 'SBX'.
ltp_dir = '\\nal.local\application\SAP\ERP\ZWELL\wmigdc\error_log\uwi_error'.
concatenate ltp_dir sy-datum '.txt' into ltp_dir.
when 'QAT'.
ltp_dir = '\\nal.local\application\SAP\ERP\ZWELL\wmigdc\error_log\uwi_error'.
concatenate ltp_dir sy-datum '.txt' into ltp_dir.
when 'PRD'.
ltp_dir = '\\nal.local\application\SAP\ERP\ZWELL\wmigdc\error_log\uwi_error'.
concatenate ltp_dir sy-datum '.txt' into ltp_dir.
endcase.
open dataset p_err2 for output in text mode encoding default message ltp_mess.
if sy-subrc = 0.
loop at t_err into s_dls.
transfer s_dls to p_err2.
if sy-subrc ne 0.
message i010(ad) with p_err2 'Download Failed'.
endif.
endloop.
close dataset p_err2.
else.
message i010(ad) with p_err2 'dataset could not be found'.
sy-subrc = -1. "Maintain error condition
endif.
open dataset p_err2 for input in text mode encoding default message ltp_mess.
if sy-subrc = 0.
do.
read dataset p_err2 into fs.
if sy-subrc = 0.
append fs to itab.
else.
exit.
endif.
enddo.
close dataset p_err2.
endif.
OPEN DATASET ltp_dir FOR OUTPUT IN TEXT MODE ENCODING DEFAULT MESSAGE ltp_mess.
if sy-subrc = 0.
loop at itab into fs.
transfer fs to ltp_dir.
endloop.
close dataset ltp_dir.
else.
message i010(ad) with ltp_dir 'dataset could not be found'.
sy-subrc = -1. "Maintain error condition
endif.
Please advice.
RegardsThere are lot of posts on the same issue: [please check this|https://www.sdn.sap.com/irj/scn/advancedsearch?query=localfilesbackground&cat=sdn_all]
-
New Event Log Errors L355-S7902
These two are recurring daily and showing up in Event Viewer>Windows>Diagnostic Performance>Operational. I have noticed that shutdown is too long so I have copied the errors.
Log Name: Microsoft-Windows-Diagnostics-Performance/Operational
Source: Microsoft-Windows-Diagnostics-Performance
Date: 8/11/2010 7:01:45 AM
Event ID: 203
Task Category: Shutdown Performance Monitoring
Level: Error
Keywords: Event Log
User: LOCAL SERVICE
Computer: Laptop
Description:
This service caused a delay in the system shutdown process:
File Name : RasMan
Friendly Name : Remote Access Connection Manager
Version : 6.0.6000.16386 (vista_rtm.061101-2205)
Total Time : 16925ms
Degradation Time : 16570ms
Incident Time (UTC) : 8/10/2010 7:44:55 PM
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Microsoft-Windows-Diagnostics-Performance" Guid="{cfc18ec0-96b1-4eba-961b-622caee05b0a}" />
<EventID>203</EventID>
<Version>1</Version>
<Level>2</Level>
<Task>4007</Task>
<Opcode>41</Opcode>
<Keywords>0x8000000000010000</Keywords>
<TimeCreated SystemTime="2010-08-11T12:01:45.242Z" />
<EventRecordID>3327</EventRecordID>
<Correlation ActivityID="{00000000-9B8C-0001-2EDB-D6AD4C39CB01}" />
<Execution ProcessID="2008" ThreadID="2144" />
<Channel>Microsoft-Windows-Diagnostics-Performance/Operational</Channel>
<Computer>Laptop</Computer>
<Security UserID="S-1-5-19" />
</System>
<EventData>
<Data Name="StartTime">2010-08-10T19:44:55.195Z</Data>
<Data Name="NameLength">7</Data>
<Data Name="Name">RasMan</Data>
<Data Name="FriendlyNameLength">33</Data>
<Data Name="FriendlyName">Remote Access Connection Manager</Data>
<Data Name="VersionLength">39</Data>
<Data Name="Version">6.0.6000.16386 (vista_rtm.061101-2205)</Data>
<Data Name="TotalTime">16925</Data>
<Data Name="DegradationTime">16570</Data>
<Data Name="PathLength">32</Data>
<Data Name="Path">C:\Windows\System32\rasmans.dll</Data>
<Data Name="ProductNameLength">37</Data>
<Data Name="ProductName">Microsoft® Windows® Operating System</Data>
<Data Name="CompanyNameLength">22</Data>
<Data Name="CompanyName">Microsoft Corporation</Data>
</EventData>
</Event>
Log Name: Microsoft-Windows-Diagnostics-Performance/Operational
Source: Microsoft-Windows-Diagnostics-Performance
Date: 8/9/2010 5:06:37 PM
Event ID: 351
Task Category: Standby Performance Monitoring
Level: Error
Keywords: Event Log
User: LOCAL SERVICE
Computer: Laptop
Description:
This driver responded slower than expected to the resume request while servicing this device:
Driver File Name : \Driver\usbehci
Driver Friendly Name : EHCI eUSB Miniport Driver
Driver Version : 6.0.6001.18000 (longhorn_rtm.080118-1840)
Driver Total Time : 271ms
Driver Degradation Time : 95ms
Incident Time (UTC) : 8/9/2010 10:11:50 PM
Device Name : PCI\VEN_8086&DEV_293C&SUBSYS_FF661179&REV_03\3&21436425&0&D7
Device Friendly Name : Intel(R) ICH9 Family USB2 Enhanced Host Controller - 293C
Device Total Time : 281ms
Device Degradation Time : 95ms
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="Microsoft-Windows-Diagnostics-Performance" Guid="{cfc18ec0-96b1-4eba-961b-622caee05b0a}" />
<EventID>351</EventID>
<Version>1</Version>
<Level>2</Level>
<Task>4003</Task>
<Opcode>35</Opcode>
<Keywords>0x8000000000010000</Keywords>
<TimeCreated SystemTime="2010-08-09T22:06:37.507Z" />
<EventRecordID>3311</EventRecordID>
<Correlation ActivityID="{00000000-06C8-0000-2E38-015FCA37CB01}" />
<Execution ProcessID="236" ThreadID="996" />
<Channel>Microsoft-Windows-Diagnostics-Performance/Operational</Channel>
<Computer>Laptop</Computer>
<Security UserID="S-1-5-19" />
</System>
<EventData>
<Data Name="StartTime">2010-08-09T22:11:50.769Z</Data>
<Data Name="NameLength">16</Data>
<Data Name="Name">\Driver\usbehci</Data>
<Data Name="FriendlyNameLength">26</Data>
<Data Name="FriendlyName">EHCI eUSB Miniport Driver</Data>
<Data Name="VersionLength">42</Data>
<Data Name="Version">6.0.6001.18000 (longhorn_rtm.080118-1840)</Data>
<Data Name="TotalTime">271</Data>
<Data Name="DegradationTime">95</Data>
<Data Name="PathLength">40</Data>
<Data Name="Path">C:\Windows\system32\DRIVERS\usbehci.sys</Data>
<Data Name="ProductNameLength">37</Data>
<Data Name="ProductName">Microsoft® Windows® Operating System</Data>
<Data Name="CompanyNameLength">22</Data>
<Data Name="CompanyName">Microsoft Corporation</Data>
<Data Name="DeviceNameLength">61</Data>
<Data Name="DeviceName">PCI\VEN_8086&DEV_293C&SUBSYS_FF661179&REV_03\3&21436425&0&D7</Data>
<Data Name="DeviceFriendlyNameLength">58</Data>
<Data Name="DeviceFriendlyName">Intel(R) ICH9 Family USB2 Enhanced Host Controller - 293C</Data>
<Data Name="DeviceTotalTime">281</Data>
<Data Name="DeviceDegradationTime">95</Data>
</EventData>
</Event>
Hope I sent the right info this time.
Donna in ARSatellite L355-S7902
Donna, I wouldn't worry that Rasman (the Remote Access Connection Manager service) takes 17 seconds to shut down. And certainly the 0.095 seconds taken by the Usbehci.sys driver is inconsequential.
My Event Viewer is filled with stuff like this. Most users don't know to look here. Best to ignore it.
Pay more attention to what's in the Application and System logs under Windows Logs.
Hope I sent the right info this time.
In the future, leave out the stuff beginning with the line..
Event Xml:
-Jerry -
Failed to set security on SQL Server registry key. Error: 2
Hi,
I have a Primary site (mixed mode) running SCCM 2007 SP1 for many months now with no issues.
This site is made up of two Win 2008 sp2 servers sharing the SCCM roles:-
SCCM01 - Site server, DP, RP, PXE and SQL2005 hosting the SCCM database
SCCM02 – SUP, MP, FSP, SLP
The SQL2005 on SCCM01 is running under a domain service account called
domain\service_sccm which is also a sysadmin in SQL as is the SCCM02 server.
In an effort to resolve the isse I have made this account a Domain Admin.
I have also used this account to log onto SEC01 to run the Secondary Site installation and to be the SQL Service account.
I'm now trying to add a Secondary Site on a Domain Controller called SEC01 (also Win2008 sp2) and on the same LAN as the SCCM01/02.
This is where I get problems.
I run the installation locally on the Sec Site server (DC) as a Domain Admin and the installation completes OK (all green ticks),
the ComponentSetup.log and Pre-Reqs are all good as well however when I check the ConfigMgrSetup.log I see the below -
Failed to set security on SQL Server registry key. Error: 2.
<11-09-2010 22:46:59> SMS Setup full version is 4.00.6221.1000
<11-09-2010 22:46:59> Successfully set security on Setup registry key.
<11-09-2010 22:46:59> Failed to set security on SQL Server registry key. Error: 2
<11-09-2010 22:46:59> Successfully set security on Identification registry key.
<11-09-2010 22:46:59> Creating SMS Inbox Source registry key ...
<11-09-2010 22:46:59> Installing SMS Site Component Manager ...
<11-09-2010 22:46:59> Installing Site Component Manager under acct <NT AUTHORITY\SYSTEM> path <C:\Program Files (x86)\Microsoft
Configuration Manager\bin\i386\sitecomp.exe>
<11-09-2010 22:47:01> Started Site Component Manager service
<11-09-2010 22:47:01> SMS Site Component Manager installation completed.
<11-09-2010 22:47:01> Done with service installation
Adding the PMP role to SEC01 also fails to install and no MPSetup or MPControl logs are created.
WebDav and win2008 roles, features all added and server fully patched.
Despooler.log on SCCM01 seems good and passing keys.
Tried installing to default path and to shortened path such as C:\SCCM
The new secondary site is listed in the console and an address can be added for the Secondary Site
BITS Server Extensions and Remote Differential Compression Features are enabled.
The Group memberships all appear ok:-
SCCM01
Local Admins
contains the sec site server SEC01, SCCM01, installation accounts
SMS_SiteToSiteConnection_001
SEC01 (the sec site server)
SMS_SiteSystemToSiteServerConnection_001
SCCM02
SEC01
No Local Admins as a DC
SMS_SiteToSiteConnection_002
SCCM01
SMS_SiteSystemToSiteServerConnection_002
empty
SQL 2005
This has the account logged in during installation as a sysadmin
SCCM02 is also sysadmin
The fundamental issue appears to be that the SEC01$ server account is not being added to SQL Logins (and therefore SCCM database Roles)
therefore the installation cannot complete.
I have tried to manually add the SEC01 account to SQL Logins before installation of Sec Site but this did not work.
Not sure if the fact that SEC01 is a DC may be a factor.
Appreciate any help if anyone has seen this before or can suggest a resolution.
ThanksAfter a lot of digging around and head scratching I eventually found the resolution.
The original thread title Error turned out to be a bit of a red herring in that my failure to deploy Sec Sites came down to two separate issues seemingly unrelated to the error message of the thread title.
The first part of the resolution was to manually create the SQL Server accounts for the Sec Site Servers and assign them to the smsdbrole_MP DB role to
let the SQL side of the SCCM install complete a s these were not being created automatically.
This then left the fact that that the installation of the Sec Site completed successfully according to the install logs in C:\ however the DP and MP would
never install.
The big clue was eventually contained in the mpfdm.log errors relating to
**ERROR: Cannot find path for destination inbox SMS_AMT_PROXY_COMPONENT on server REGISTRY SMS_MP_FILE_DISPATCH_MANAGER
and
**ERROR: Cannot find path for destination inbox Asset Intelligence KB Manager on server REGISTRY SMS_MP_FILE_DISPATCH_MANAGER
Thankfully the errors led me to these two blogs:
http://myitforum.com/cs2/blogs/scassells/archive/2009/07/20/error-cannot-find-path-for-destination-inbox-sms-amt-proxy-component-on-server-registry.aspx
and
http://social.technet.microsoft.com/Forums/en-US/configmgrsetup/thread/5fcc53d4-8629-4b34-9eaa-6cb020eedc13/
As it turned out the SCCM installation registry and folder creation does not complete and I had to manually enter the reg settings as detailed in the
links above to complete the installation. Once I did as described everything worked a treat – all my MPs and DPs are 100% now.
Solutions
Add the following reg keys to each of your effected secondary sites.
Inbox Fix
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\SMS\MPFDM\Inboxes]
"Asset Intelligence KB Manager"="E:\\Program Files\\Microsoft Configuration Manager\\inboxes\\AIKbMgr.box"
"SMS_AMT_PROXY_COMPONENT"="E:\\Program Files\\Microsoft Configuration Manager\\inboxes\\amtproxy.box"
Asset Intelligence fix:
Note: you will need to identify the next largest key value.
In my example it was key 49
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\SMS\Inbox Source\Inbox Definitions\49]
"Inbox Name"="Asset Intelligence KB Manager"
"Relative Path"="inboxes\\AIKbMgr.box"
"NAL Path"=""
"User Rights"=dword:00000000
"Service Rights"=dword:00000004
"Monitoring Enabled"=dword:00000001
"Location Type"=dword:00000001
"Guest Rights"=dword:00000001
AMT registry Fix.
Note: you will need to identify the next largest key value.
In my example it was key 50
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\SMS\Inbox Source\Inbox Definitions\50]
"Inbox Name"="SMS_AMT_PROXY_COMPONENT"
"Relative Path"="inboxes\\amtproxy.box"
"NAL Path"=""
"User Rights"=dword:00000000
"Service Rights"=dword:00000004
"Monitoring Enabled"=dword:00000001
"Location Type"=dword:00000001
"Guest Rights"=dword:00000001
Big thanks to Shaun Cassells and John Marcum for these blogs -
Error 1603 in deploying Office 2003 by creating an application object using its MSI package!
Hello,
I got the error of 1603 when I ran Office 2003 MSI package through NAL. I
have no idea how to resolve this problem. Even though I enabled logging in
Office 2003 installation, I still could not figure out what went wrong and
what caused the error.
I have used Snapshot to create an application object for a long time with
little problem. However, I could not successfully deploy any MSI package
created by an application object. I knew ZenWork Managing Application has
the feature, but I don't know how to make it work in our environment.
Do I have to know more about Microsoft Window Installer ?
Appreciate your comments and experience in advance
Thanks
Joe Liu
email: [email protected][email protected],
> I got the error of 1603 when I ran Office 2003 MSI package through NAL
>
Start here:
http://support.novell.com/techcenter...tation&x=0&y=0
Yes, understanding MSI helps. FWIW I have deployed 2003 this way.
- Anders Gustafsson, Engineer, CNE6, ASE
NSC Volunteer Sysop
Pedago, The Aaland Islands (N60 E20)
Novell does not monitor these forums officially.
Enhancement requests for all Novell products may be made at
http://support.novell.com/enhancement
Using VA 5.51 build 315 on Windows 2000 build 2195 -
NAL apps not showing in citrix unless an admin is logged in
We have got 3 citrix server publishing a desktop. They are using Metaframe XPe feture release 3 sp4 on win2k.
The problem we are having is that unless an admin is loged onto each server the users don't get NAL icons. We use the NALEXPLD to deliver the apps. If I logon to a server as a user and manualy run NALEXPLD nothing hapends. There are no errors. As soon as an admin is loged onto that server the user can run nalexpld and the icons are there.
This is not a big problem but it meas leaving an admin loged in all the time on every server. It also means tha twe can't schedual reboots of the servers as when users connect they don't get icons untill an admin is loged in.davidleader,
It appears that in the past few days you have not received a response to your
posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Visit http://support.novell.com and search the knowledgebase and/or check all
the other self support options and support programs available.
- You could also try posting your message again. Make sure it is posted in the
correct newsgroup. (http://forums.novell.com)
Be sure to read the forum FAQ about what to expect in the way of responses:
http://forums.novell.com/faq.php
If this is a reply to a duplicate posting, please ignore and accept our apologies
and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://support.novell.com/forums/ -
Unknown error occurred for application (application name) (id=5 [5], 5[5])
Environment: ZFD4
Windows OS: 2000 Professional Sp4
Novell Client: Tried both: 4.83SP2 and 4.91SP3
Zenworks Server: NW51 SP6
I successfully created a NAL object for an application called Delphi from
a company called NewMarket. The Application utilizes an SQL database and
runs off a Windows 2000 server. We already have one NAL object for this
application which works fine. The new object I created is for a newer
version of this appliction.
I have compared all the settings, and parameters of the new object with
the old one and all are in identical. I am not entirely sure of every
registry or INI entry though.
On trying to deploy the object, the files and registry entries of the
application seem to get copied to a point from what I can see but then it
always ends up with this error: " Unknown error occurred for application
DelphiMV92.Woodbine.OJC (id=5 [5], 5[5]).
I did a search for this error off Novell's knowledge base but came up
empty.
Any thoughts about what could be the problem?
Will greatly appreciate any help with this.
Thanks very much
KennethOriginally Posted by Craig Wilson
Export the object as an "AXT" file and mail to
Craig_D_Wilson at yahoo dot com
Craig Wilson - MCNE, MCSE, CCNA
Novell Support Forums Volunteer Sysop
Novell does not officially monitor these forums.
Suggestions/Opinions/Statements made by me are solely my own.
These thoughts may not be shared either Novell or any rational human.
"Kenneth " <[email protected]> wrote in message
news:_vl0i.484$[email protected]..
> Environment: ZFD4
> Windows OS: 2000 Professional Sp4
> Novell Client: Tried both: 4.83SP2 and 4.91SP3
>
> Zenworks Server: NW51 SP6
>
> I successfully created a NAL object for an application called Delphi from
> a company called NewMarket. The Application utilizes an SQL database and
> runs off a Windows 2000 server. We already have one NAL object for this
> application which works fine. The new object I created is for a newer
> version of this appliction.
>
> I have compared all the settings, and parameters of the new object with
> the old one and all are in identical. I am not entirely sure of every
> registry or INI entry though.
>
> On trying to deploy the object, the files and registry entries of the
> application seem to get copied to a point from what I can see but then it
> always ends up with this error: " Unknown error occurred for application
> DelphiMV92.Woodbine.OJC (id=5 [5], 5[5]).
> I did a search for this error off Novell's knowledge base but came up
> empty.
>
> Any thoughts about what could be the problem?
>
> Will greatly appreciate any help with this.
>
> Thanks very much
> Kenneth
>
I had the same type of error and found that the version of snapshot was different then the version of zen on our network. When I matched the two versioin the snapshot worked perfect. Hope this helps. -
I keep getting network error on Facebook on my iPad
My Facebook was working fine on my Wi Fi but in the last week I keep getting network error when trying to logon to Facebook from my iPad & iphone 5s. I have time warner road runner digital cable. How do I fix it?
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are drooping internet connection)
• Launch Settings app
• Tap on Wi-Fi
• Tap on the blue arrow of the Wi-Fi network that you connect to from the list
• In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Fix WiFi Issue for iOS 7
http://ipadnerds.com/fix-wifi-issue-ios-7/
iOS 6 Wifi Problems/Fixes
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
iPad: Issues connecting to Wi-Fi networks
http://support.apple.com/kb/ts3304
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
10 Ways to Boost Your Wireless Signal
http://www.pcmag.com/article2/0,2817,2372811,00.asp
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
Some Wi-Fi losses may stem from a problematic interaction between Wi-Fi and cellular data connections. Numerous users have found that turning off Cellular Data in Settings gets their Wi-Fi working again.
You may have many apps open which can possibly cause the slowdown and possibly the loss of wifi. In iOS 4-6 double tap your Home button & at the bottom of the screen you will see the icons of all open apps. Close those you are not using by pressing on an icon until all icons wiggle - then tap the minus sign. For iOS 7 users, there’s an easy way to see which apps are open in order to close them. By double-tapping the home button on your iPhone or iPad, the new multitasking feature in iOS 7 shows full page previews of all your open apps. Simply scroll horizontally to see all your apps, and close the apps with a simple flick towards the top of the screen.
Wi-Fi or Bluetooth settings grayed out or dim
http://support.apple.com/kb/TS1559
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
Clients getting errors after ZAM deployment
Hi, I have created one NAL to deploy the ZAM Asset management to all Asian workstations. now there is one site all workstations getting one errors "windows xp setup: the application could not be initialized when start up" after deployment. this error always happened whenever client startup. please advise
how to get rid of that. thanks.
<img>http://www.rayha.350.com/zam.jpg</img>rayha,
It appears that in the past few days you have not received a response to your
posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Visit http://support.novell.com and search the knowledgebase and/or check all
the other self support options and support programs available.
- You could also try posting your message again. Make sure it is posted in the
correct newsgroup. (http://forums.novell.com)
Be sure to read the forum FAQ about what to expect in the way of responses:
http://forums.novell.com/faq.php
If this is a reply to a duplicate posting, please ignore and accept our apologies
and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://support.novell.com/forums/
Maybe you are looking for
-
Cannot print adobe documents ... Error message indicates a need to install plug-in for adobe reader. Please advise how/where to locate the required adobe reader plug-in... Thank you, Joe Curcio
-
Open a pdf in Photoshop CS5 shows jpg - but no grafic
I have a handbook opened in Photoshop CS5 and I can see the jpg images of the handbook. But not the grafic scematic images. I am not aware if these are in svg or whatever. How can I get access to those grafics? Yes, I may open a page and copy a grafi
-
Photo storing app won't open after update.
This is kind of embarrassing. I downloaded the app Private Photo Vault on my jailbroken iOS 7.1.2 iPhone 4. I used this app to lock away some inappropriate pictures I didn't need other people seeing in my library. It had worked perfect until the upda
-
"Apply Active Content Update" message ONLY in Firefox
Here's my new website: www.ClampTools.com When I view it in IE it looks great. When I view it in Firefox (like for the Press link) I get this error: This page requires AC_RunActiveContent.js. In Flash run "Apply Active Content Update" in the Commands
-
Not able to add music files to mobile
I am not able to add music files to mobile. While trying to add it is not showing any message and the file is not geting added to itunes library