Nano 7th gen reset causes itunes sync to quit

My 7th gen nano spontenaously lost 95% of its music so I reset it back to factory status.  Then when I tried to use iTunes to refill (snyc) the Ipod to the music from my computer using file / devices / sync it was greyed out and the only choice was "Transfer purchases from Ipod".... (ipod empty from reset)
How can this out of sync syncing function be resolved?

Try deleting all remnants of iTunes from your computer then download and install iTunes again.
What other USB devices are connected to your Dell?

Similar Messages

  • HT1386 Itunes recognises my ipod nano 7th gen but won't sync (also have another ipod nano 6th gen who uses this same computer, different Apple ID, no probs syncing)

    Two ipod nanos registered to same PC
    Both with own Apple ID
    Up until recently able to sync both ipods no problem
    Now, the 7th gen ipod nano, unable to sync and all music previously synced has dissappeard from ipod (thankfully still in itunes).
    Could Homesharing have something to do with it? 
    Thanks in advance if anyone can help...have one unhappy 11yr old music lover!

    Hi kumaradevan.g,
    Welcome to Apple Support Communities.
    It sounds like there is an issue syncing music to your iPod from a specific laptop. The article linked below provides a lot of great tips that can help resolve the syncing issue that you described.
    'Disk cannot be read from or written to' when syncing iPod or 'Firmware update failure' error when updating or restoring…
    http://support.apple.com/kb/ht1207
    I hope this helps.
    -Jason

  • Nano 7th Gen resets when I attempt to calibrate niki shoe sensor

    I cannot calibrate the Niki Shoe sensor.  As I get close to completing the calibration the Nano shuts down and restarts.  Also, I can never see the calibration of just doing a basic run registering as a run, the data is registering as a walk.  Yesterday during a basic run, the Nano did a restart just before I completed my three miles.
    Is this a Nano defect or a Niki Sensor defect?
    Thanks,
    Ray

    Hi Ray,
    Welcome to the Support Communities!
    The article below may be able to help you with this.
    Nike + iPod: Receiver not recognized by iPod nano
    http://support.apple.com/kb/TS1484
    Nike + iPod Frequently Asked Questions (Technical)
    http://support.apple.com/kb/ht2293#faq8
    How do I calibrate or recalibrate the Nike + iPod system?
    To learn how to calibrate Nike + iPod system, please read "Nike + iPod: How to calibrate the Nike + iPod Sport Kit" or the Nike + iPod User's Guide.
    Ordinarily, the sensor does not require recalibration. You may want to consider recalibrating if your fitness level changes or if you would like to try to improve the accuracy of your results.
    Cheers,
    - Judy

  • IPod nano (7th gen) and iTunes have said it is 'synced' however no songs show when disconnected. Once reconnected, storage says data if fully free even though sync took place, experience of same, help?

    IPod nano (7th gen) and iTunes have said it is 'synced' however no songs show when disconnected. Once reconnected, storage says data if fully free even though sync took place, experience of same, help please?

    IPod nano (7th gen) and iTunes have said it is 'synced' however no songs show when disconnected. Once reconnected, storage says data if fully free even though sync took place, experience of same, help please?

  • I previously owned iPod Touch -New iPhod Nano 7th Gen. Can't  seem to be recognized by iTunes or Sync

    I previously owned an iPod Touch. I received an iPod Nano 7th Gen. for Christmas. How can I get the device to be recognized by iTunes and Sync my music? I tried all the Troubleshooting and it doesn't seem to work

    Try this one:  iOS: Device not recognized in iTunes for Windows, http://support.apple.com/kb/TS1538
    Then see Purchasing iOS 3.1 Software Update for iPod Touch (1st Generation), http://support.apple.com/kb/HT2052

  • IPod Nano 7th Gen says "Unsupported. Accessory is not supported" when trying to charge / sync

    iPod Nano 7th Gen says "Unsupported. Accessory is not supported" when trying to charge / sync with official apple lightening cable.
    It worked for almost a year then suddenly began to say that. My computer [windows], lightening cable and my power brick [all apple official] are all the same as they were when it was working. The iPod is almost a year old now, and has worked perfectly up until about a week ago.
    I have tried resetting the iPod, plugging it into different charging sources but it keeps saying "Unsupported. Accessory is not supported"
    Does anyone have any ideas on how to fix it?
    Thanks.

    Your iPod Nano firmware and iTunes updated to the current versions? 
    It is very difficult to offer troubleshooting suggestions when the "os version" you are using is unknown as each os has their own troubleshooting solutions. 

  • My ipod nano 7th gen no longer shows "Playlists" in the music menu. No changes made other than deleting one and adding one playlist to those synced. Synced fine in late February. Not working as of 3/7/2014.

    My ipod nano 7th gen no longer shows "Playlists" in the music menu. No changes made other than deleting one and adding one playlist to those synced. Synced fine in late February. Not working as of 3/7/2014.

    I would either say that the iOS is correpted due to a software glitch or y have have a hardware problem like bad memory locations that are corrupting the iOS.
    - Restore from backup via iTunes. This will install a fresh copy of the iOS. See:                                                
    iOS: How to back up                                                                                     
    - Restore to factory settings/new iOS device.   This will elimate corruptin in the backup causing the problem.          
    If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
      Apple Retail Store - Genius Bar

  • IPod nano 7th gen not recognised in iTunes using Windows 8.1

    I have an older 3rd generation iPod nano and a new 7th gen nano and I would like to sync them to the same iTunes on my Dell laptop (Inspiron 7520) running Win8.1. I have also updated iTunes to the latest version.
    When I connect the new 7th gen iPod nano to my laptop via USB (tried all 4 ports)  I get the following error message from iTunes:
    "An iPod has been detected, but it could not be identified properly. Please disconnect and reconnect the iPod, then try again."
    I've been through most of http://support.apple.com/kb/TS3218  and still get the error message although I haven't tried connecting the iPad nano 7th gen to an older Win7 laptop yet with a fresh iTunes install.
    When connecting the iPod nano7 Win8.1 recognises E: as an iPod very briefly after I have run a scan via McAfee. After a few seconds the E: drive disappears and iTunes reports the error message as above.  Sometimes, E: doesn't disappear in Win8.1 but I still get the iTunes error message and the iPod nano itself goes from Connected to Main menu.
    Any ideas how I can get iTunes to recognise my 7th gen nano?  I'm not sure if this is a Win8.1 problem or iTunes.

    Hello Abbey,
    I would recommend the steps in this article named iOS: Device not recognized in iTunes for Windows found here http://support.apple.com/kb/TS1538. While the title of the article describes a symptom a bit different from yours, I feel the troubleshooting is still relevant.
    If that does not resolve the issue, then I would suggest this article to help troubleshoot the USB connection.
    iOS: Troubleshooting USB connection
    http://support.apple.com/kb/ts1286
    And lastly, resetting it just may do the trick.
    How to reset an iPod nano (7th generation)
    Press and hold the Sleep/Wake button and the Home button until the screen goes dark. The Apple logo should appear after a few seconds, then the Home screen should appear.
    From: How to reset iPod
              http://support.apple.com/kb/ht1320
    Take care,
    Sterling

  • I have a bright white screen when turning on my ipod nano 7th gen.  Have tried resetting etc etc. Any further ideas?

    I have a bright white screen when turning on my nano 7th gen. Have tried resetting and restoring settings - no change. Any ideas please?

    Hello pipworms,
    I would be concerned too if my iPod nano's was just showing a white screen.  I recommend following the steps below:
    Display shows a white screen
    Try putting the iPod into disk mode:
    Reset the device (Reset the device by pressing the Sleep and Home buttons simultaneously until the display shows the Apple logo. This should take about eight seconds).
    When the Apple logo appears, press and hold the Volume Down and Volume Up buttons simultaneously until the device enters Disk Mode.
    While the device is in disk mode, sync it to iTunes and try to restore.
    I got this information from the following article for the 6th generation iPod nano.  The steps are the same, except I updated the reset steps with the reset for the 7th generation iPod nano:
    iPod nano (6th generation): Hardware troubleshooting
    http://support.apple.com/kb/ts3474
    How to reset iPod
    http://support.apple.com/kb/ht1320
    Putting iPod into Disk Mode
    http://support.apple.com/kb/HT1363
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • Am trying to sync my ipod nano 7th gen. i get this message: not enough access privileges."

    i am trying to sync my ipod nano 7th gen with my music on the cloud, via a desktop PC.
    I have successfully done this in the past.
    now I am getting a series of messages: "not enough access privileges"
    have reset the nano and also downloaded latest iTunes software.
    Any suggestions?

    Hi,
    I'm having a very similar problem, so I was excited to see the link above. But when I click on it, it redirects me to the nike.com main website (I'm assuming Nike redid their website since the above link was posted). Could you please point me to that article somewhere else or tell me how you fixed your problem?
    My exact problem is this: I was running until recently with my iPod Nano 6th gen and the Nike+ sensor kit (sensor that goes in the Nike+ shoe plus receiver that goes in the iPod Nano). When I would sync my Nano with iTunes (I would have the "Automatically send workout data to nikeplus.com" option checked), all was well with this set-up as far as syncing my stuff to the Nike+ website goes.
    I recently realized that for the iPod Nano 6th generation, the sensor/receiver combo is not required anymore. So I ran two runs without the receiver. I kept the sensor in the shoe though as nowadays I mostly run with my recently purchased Nike+ Sport GPS watch and I like to have the sensor in the shoe in case the GPS signal gets lost at some point during a run. Anyway, those two runs that I ran without the receiver won't sync to my nikeplus account. I can see them in my iPod Nano's history and I can see one of them (the latest one) on the Nike + iPod tab of iTunes when I sync my Nano. The difference though is that on iTunes this latest run appears under a "Sensor 1" selection, whereas all my previous runs with both the sensor and receiver would be under "Nike + Sensor" selection. Within the "Nike + Sensor" selection, under nikeplus.com, there's the "Automatically send workout data to nikeplus.com" option and below it a Login ID that shows my Nike+ website log-in info. Within the "Sensor 1" selection, the Login ID is missing. I've tried renaming "Sensor 1" to something else but it didn't make the Login ID appear.
    Thank you for reading this and any help would be greatly appreciated.
    Best,
    Dimitris.

  • Just bought a nano 7th gen, itunes won't load existing music library onto it

    I Just bought an a Nano 7th gen, printed off the pnline maual and still can't get it to load my existing library onto to it.  I tried reseting the nano and changing computer ports but it still won't load. What do I do ???

    Hey there Ellens1,
    It sounds like you are trying to sync your music to your iPod Nano but something is preventing the sync. If you are using the the following process to sync the content:
    iTunes: Syncing media content to iPod
    http://support.apple.com/kb/ht1351
    I would next use the following troubleshooting in the following article to help resolve the issue:
    http://www.apple.com/support/ipodnano/assistant/itunes/
    Thank you for using Apple Support Communities.
    Take care,
    Sterling

  • Why can I sync a movie but not TV shows on my nano (7th gen)?

    I am using iTunes 11.0 and can sync a movie (Miracle on 34th Street) to my new ipod nano 7th gen but when I try a TV Show (a Planet Earth HD episode) or even a brief video clip taken with my camara I am told that such an action is not permitted on this ipod.  So why can I sync a movie but not TV shows on my nano (7th gen)?  Thank you.

    Before you can sync video files, it must be converted into a format compatible with ipod.  If you can’t sync a video convert it by doing the following:
    In iTunes, select the video you want to convert. Do one of the following then sync again after:
    1) Choose File > Create New Version > Create iPod or iPhone Version.
    2) Choose File > Create New Version > Create iPad or Apple TV Version.
    I hope this works.

  • I got a new iPod nano 7th gen., but when I tried downloading a video from my iTunes library a message popped up that said: Some of the videos in your iTunes library cannot be copied to your iPod because they cannot be played on this iPod.

    I got a new iPod nano 7th gen, but when i tried downloading a video from my iTunes library a message popped up that said: Soem of the videos in your iTunes library were not copied to yor iPod because they cannot be played on this iPod. What should I do?

    I kept having a similar problem - 3 out of the 10 videos I had on iTunes wouldn't sync. They were in the right format and I KNEW they worked on my iPod because I'd RECORDED them on my iPod. I finally figured out what to do! Go to the movies in your iTunes library. Click on one that does not sync. Click on "Advanced" at the top of iTunes and choose "Create iPod or iPhone version". Once that's finished, be sure you delete the old version so you don't keep getting the error (or have 2 copies of the same video) and sync. This should eliminate the problem. At least it did for me!

  • I accidentally dropped by old ipod in the garage and drove over it.  So I bought an ipod nano 7th gen. to replace it.  Can I transfer the itunes from my old ipod to my new one?  I only have about 30.

    I accidentally dropped by old ipod in the garage and drove over it.  So I bought an ipod nano 7th gen. to replace it.  Can I transfer the itunes from my old ipod to my new one?  I only have about 30.

    AAll of your iTunes purchases can be re-downloaded again. Log into iTunes Store, select the Purchases tab for Apps, Music, etc.
    if you've been syncing your old iPod with iTunes, you can restore everything to your new iPod from the old backup.

  • Do I have to have an iTune account to use the Ipod Nano 7Th Gen?

    Do I have to have an iTune account to use the Ipod Nano 7Th Gen?

    No, you don't. You can rip music to your computer and sync it to your Nano.

Maybe you are looking for