Nano a little wet - how to tell if dead?

My nano, in it's protective rubber case, somehow got wet (maybe a little splash over from some ice coffee or water while in the car, I doubt sweat from running), probably a week or so ago, and I did not realize it. When I did, I took it out of the case, the dampness made it slide out very easy, and the little plastic protective covers that fit over the screen and clickwheel did have moisture underneath them when I removed them. At some point the screen said it was charging when it wasn't, I did stick it on the Orb MStation player/charger (i realize now a cardinal sin), it said it was charging, and the it did play on the charger!!!!, but it did not complete the charge, and when removed, it would not come on.
So, I removed the battery, a NewerTechnology one I self-installed 6 months ago and am in the process of drying it out. My over all question is, if it doesn't work in a week or so after the drying (all tips are welcome in that process), how do I know if I should junk it? If it plays on the Mstation, should I just get a new battery? Should I try to get a local tech (New Orleans) to check it out? What do they need to test to see if it can still work? Thank you!!!

I followed your lead, put the nano (now dry for 2 weeks) in the charger and it charged! And iTunes recognizes the ipod.
BUT, when playing the ipod once it's disconnected, and then pausing it for a bit, if it turns itself off (after about 2 minutes the screen goes total dark - is that sleep mode?), and I hit the Play button, it will come back on, and say on the screen that it's playing, but it is not. I have to do a reset (Menu and Select pressed simultaneously) to get it to play again, but it goes back to the first selection on the list and starts all over.
I did a Restore using the Software Updater utility that is on my computer (dated 1/10/2006) - no change.
I went into Diagnostic Mode (a reset then Rewind - Select simultaneous when you see the Apple logo), I think I ran everything on the list from the FiveInOne Test on down, and I think everythiing passed so . . . what could still be the issue? Seems a little weird because all the physical buttons work and the software was restored so if anyone has an idea, that would be great!

Similar Messages

How do I get the little screen back, that tells me how much ink I have left in my print cartridges?

How do I get the little screen back, that tells me how much ink I have left in my print cartridges? It used to show up whenever I would print something, now it doesn't and I have no idea how much ink is left in the cartridges. I have a HP Photosmart C4180 All in One Printer. I recently purchased new computer, a HP Pavilion P7-1254 AMD Vision, which runs Windows 7. I just want to know how to get the screen back that tells me how much ink I have left. Thanks.

Hi there pyesangel,
Open the Printer Toolbox . There are two ways to do this:
Open HP Solution Center , select the Settings menu, then the Print Settings submenu, and finally the Printer Toolbox .
Open Printers and Faxes in the Windows Control Panel , then right-click your printer icon and choose Properties . Click Printing Preferences . Click the Features tab, then click the Printer Services button.
The Printer Toolbox opens. Click the Estimated Ink Level tab. A cartridge may be running out of ink even if the graphic shows ink remaining (see the note at the start of this section). Lines or streaks always appear in printouts when the cartridges begin to run out of ink. Replace print cartridges that are out of ink or low on ink.
Figure 1: Estimated ink levels
Give it a shot and let us know if it helps.
Best of Luck!
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

Can i use wireless earbuds with my ipod nano 6th. if yes how do i do it ?

can i use wireless earbuds with my iPod nano 6th generation ? If yes, tell me how to do it. Thank you

You will need this: http://www.amazon.com/KOKKIA-MULTI-STREAM-multi-stream-authentication-Capabiliti es/dp/B004I408OW/ref=sr_1_1?ie=UTF8&qid=1405309396&sr=8-1&keywords=bluetooth+ipo d+adaptor

How to tell embedded jinitator applet is still running when window closed

Hello, we are trying to accomplish the same thing that is mentioned in this post from Metalink. I've searched for a solution and hope someone here can help. Instead of restating the issue I think David Wilson does a good job of explaining what is needed. Can anyone please suggest a possible solution?
From: David Wilton 07-Oct-05 01:08
Subject: How to tell embedded jinitator applet is still running when window closed
How to tell embedded jinitator applet is still running when window closed
Hi,
We run an oracle 10g forms application through 9iAS over an intranet. All users are running windows 2000 professional.
We run separate frame = true but I would like to switch to separate frame = false
With separate frame = true if the user clicks the outer windows "X" close button (forms mdi window) the user is prompted to save changes before the application ends.
BUT
when using separate frame = false
If the user clicks the upper window "X" button (no longer form mdi window but regular browser window) the window and application is abruptly closed.
I'm interested in using a onbeforeunload function to confirm if the user wants to close the window. This would be placed in the basejini.htm file. This could always ask if the user wants to exit or not. If they click OK then the window closes but if they click "Cancel" you are returned to the forms application exactly where you left. something like event.returnvalue="do you really want to exit?";
However if the user exited using the normal exit form method then the applet is already closed before the onbeforeunoad event fires and there is nothing to go back to and I want the window to close automatically. This is accomplished using close.html file in post forms trigger.
So what I want and what I think many may also want is the check if the embedded applet is still running and if so prompt the user to return to the application or continue to close. Of course If the applet is no longer running then just close because there is no reason confirm closing anymore.
Does anyone have a html/JavaScript solution that can be placed in the jinitiator.htm file? or similar?
Thank you
David
[email protected]
From: Andrew Lenton 07-Oct-05 08:58
Subject: Re : How to tell embedded jinitator applet is still running when window closed
I don't know if this is exactly what you are after but you can add the following to the top of your basejini.htm file and it should prompt the user before exiting the IE window.
<BODY %HTMLbodyAttrs%>
%HTMLbeforeForm%
<SCRIPT>

</SCRIPT>
From: Oracle, mohammed pasha 07-Oct-05 09:55
Subject: Re : How to tell embedded jinitator applet is still running when window closed
David,
Well I could not understand your complete requirement.
Refer to Note.201481.1 How to Close the Browser Window When Closing Forms And How to Simulate SeparateFrame By Javascript
Note.115905.1 How to Close Browser Window When Closing Webforms Applet
Kind Regards,
Anwar
From: David Wilton 07-Oct-05 14:37
Subject: Re : How to tell embedded jinitator applet is still running when window closed
Thank you for your reply and yes you did not understand my question fully.
Sorry if this is a long reply
I am able to close the browser window using information in notes 115905.1 and 201481.1, this is not the issue. We implemented this several years ago. It is workable for both separate frame = true or false.
It is most important to not allow the user to end their forms application by closing the windows browser, they must close using normal form exit commands.
What I want is to have separate frame = false, the big drawback to this option is the user can exit the application and bypass all forms code by pressing the windows "X" close button. This is why we need the code as just provided by Andrew Lenton above in this thread.
BUT Andrew's code will always prompt the user before closing the window and I do not want that. I want the user to be prompted only under scenario 2 listed below.
Here's the 2 case scenario for exiting the application.
1. If the user closes properly and uses exit form which fires all normal form triggers including post_form with it's call to close.html file.
All uncommitted changes are saved or rollback and the users session is ended normally both on the database and in the application server.
All browser windows will close, great all is good. And without Andrew's code the window will close but with Andrew's code the user will be prompted to close or not, if they select Cancel the window will remain but the applet has already ended so why prompt? ...This is what I want to avoid.
2. In the forms app. if the user clicks the windows "X" close button with uncommitted changes. The browser just closes the changes are rollback without prompting the user to save. The users sessions are now lost and still running in the database and application server until they are timed out.
If I use Andrew's code then the user will be prompted to continue to close or go back, if they click Cancel to go back then focus returns to the forms application and the user can continue to work. If the user clicks OK then the window closes and unfortunately their sessions are still lost until timed out.
So what I desire is to add to Andrew's code to check if the embedded applet is still running and prompt the user to close or not accordingly.
Something like:
Basejini.htm like
</HEAD>
<SCRIPT LANGUAGE="JavaScript">
function maximizeWindow()
window.moveTo(0,0);
window.resizeTo(screen.availWidth,screen.availHeight);
function confirm(){
If(document.embeddedapplet.closed())
Win.opener = self;
win.close();
Else if
event.returnValue = "Closing Forms Application. OK to continue?";
</SCRIPT>
<BODY %HTMLbodyAttrs%, onload="maximizeWindow()", onbeforeunload="confirm()">
%HTMLbeforeForm%
I hope this explains my requirements.
David
From: Oracle, Evelene Raechel 10-Oct-05 06:45
Subject: Re : How to tell embedded jinitator applet is still running when window closed
Hi,
Note.199928.1 How to Alert User on Closing Client's Browser Window in Webforms
Regards,
Rachel
From: David Wilton 11-Oct-05 17:40
Subject: Re : How to tell embedded jinitator applet is still running when window closed
I'm sorry this is not helpful at all.
Note 199928.1 is only an alert which does not stop the closing of the window and still displays as an alert if the user does close properly using exit form ... so why would you want to display the alert then?
This is exaclty what I do not want and why I want to determine if the applet is still running before displaying any kind of message.
David
From: Oracle, Evelene Raechel 17-Oct-05 12:23
Subject: Re : How to tell embedded jinitator applet is still running when window closed
Closing thread.
Thanks,

Hello,
I had the same issue last year - wanting to provide a warning on closing the browser, but only if the Forms session is still running. The approach I took is described below, see also the thread where I originally posted this at Closing brower window
Hi there,I've had a similar requirement - or rather, the two conflicting requirements: to warn when the browser is being closed, but for the app to be able to close the browser without a warning being fired.
To always provide a warning when someone (the user or the Forms app) tries to go to a different page (e.g. your close.htm), use Javascript like:
function confirmExit(){
if(appletRunning==true) {
msg="Closing this window or navigating to another page will end your SomeGreatApp session.";
window.event.returnValue=msg;
And make a call to confirmExit() in the onBeforeUnload event of your main page.
You'll notice I first check an 'appletRunning' variable before displaying the warning. This Javascript variable is set to true by my app when it starts up, using an embedded Javabean that calls out to Javascript. Once that variable is set to true, then the warning will be displayed if the user tries to shut the browser by clicking on the 'x' button, or to go to a different URL.
When my app is shutting down, it uses the same Javabean to set appletRunning back to false. It then navigates to a close.htm - which will be done without a warning being displayed.
See Re: How can a Javabean call Javascript function of the basejpi.html?? for example code on how to call Javascript from a bean embedded in your Forms app.
Hope these ideas help you out, it's worked for me (so far, anyway!!)
James

How to tell N6.5 DHCP to use a W2k8 for PXE?

Hello,
could anyone give me a hint, how to tell my netware DHCP to use a Windows Server 2008 R2 running Acronis with PXE Server?
Actual Situation:
Netware 6.5 Sp8 Server with ZENWORKS in Cluster mode
Netware DHCP Server
ZEN7 SP1 Imaging
--> works fine so far, and no problem in other subnets, IP-helper are configured in the switches
New Situation:
Netware 6.5 Sp8 Server with ZENWORKS in Cluster mode
Netware DHCP Server
Windows Server 2008 R2 running Acronis Snap Deploy with PXE-Server - in future may be a clean Windows Deployment service without Acronis
--> that would be nice :)
I found serveral ini-files (dts.ini, pdhcp.ini, tftp.ini) where I configured the new IP-Address of the W2k8 PXE Server.
Now:
The Client gets its correct IP-Address from Netware DHCP
but after that the following messages:
Auto-select:
ZENworks Boot
Boot Server IP: --.--.--.-- (the correct one configured in the ini-files!)
TFTP.
PXE-T02:
PXE-E3C: TFTP Error - Access Violation
PXE-M0F: Exiting Intel Boot Agent
Any ideas?
Thanks a lot.

Originally Posted by magic31
You don't have to configure anything specifically in DHCP to work with PXE. Possibly just unconfigure an option that was set for the previos setup; One thing to check (and remove) is option 60 for the PXE Client option, if this is configured with the DHCP subnet options. This option should only be set if both DHCP and PXE services are on the same server (as is probably the case in your situation as I'm guessing both DHCP as also PXE get loaded in the same cluster resource script).
For subnets serviced outside of the subnet your DHCP server is running in, you will need to configure multiple ip helpers: one that points to the DHCP server and one points to the PXE server so those requests on other subnets get serviced correctly.
To get things running it's probably easier to try to get this to work on the subnet your DHCP and PXE server are running in (so you are not also having to deal with the ip helper setup just yet). If that works, then expand you configuration to different subnets & ip helpers.
Hope that helps,
Willem
As a ps and for clarification, don't load the PDHCP on any of the NetWare servers... just have the PXE PDHCP service running on the Windows server.
The PDHCP/PXE service for ZenWorks won't understand/work with the Arconis one and visa versa.
-Willem

I WANT TO GIVE MY OLD NANO TO SOMEONE. HOW DO I DISOWN IT FROM MY ITUNES ACCOUNT?

I want to give my old Nano to someone. How do I disown it from my account, so that it can be setup on a different iTunes account?

Restore

How to tell if Im on AT&T?

Hey guys. I guess I live right on the edge of an area covered/not covered by at&t. I have noticed that my reception bars have changed from black and white to colored and I have even seen a E next to it. So my question is how do I make sense of the different colors or letters so I know if Im on AT&T or some other network?

how to tell if Im actually using at&T's own cell towers or a competitors.
You will never be using a competitor's towers. A competitor would be T-Mobile, Sprint, Verizon, etc. and you'll never connect to their networks. You may in some cases be using an AT&T partner. In this thread, one poster advised:
"To get an indicator when you are roaming on an AT&T partner network, call 611 and ask them to activate the (free) "Off Network Alpha Tag" on your account. If they ask why, tell them you want to be a good guy and observe the (usually unenforced) data limits while roaming."
Hope that helps.

How to tell if REQ1 is set active high

Hi I am using the 6533 PCI-DIO-32HS card in a PC with traditional DAQ, looking at an existing design. I could not find how to tell if REQ1 is set active high or low, guessing it would be set up in the DIO confg vi.

thanks for the additional information, yes will have to wait for the external hardware. I did have a general question about the 6533 data and control line outputs using traditional DAC. I think for this design it is set up as a pattern IO transfer using internal REQ and an internal clock set up as a VI input, (DIO START). Anyhow I am monitoring the card outputs with a logic analyzer and it looks like an 8 element array (of 8 bit integers) is being used for the data input (to the DIO WRITE VI) with the first 4 elements being written out on DIOA0-A7, DIOB0-B7, DIOC0-C7, and DIOD0-D7 followed by the last 4 elements also written out to DIOA0-A7, DIOB0-B7, DIOC0-C7, and DIOD0-D7. Anyhow it looks like the clock input to the (DIO Start VI) controls the pulse width of the data. It looks like REQ1 goes high approximately 78 microseconds before the first 32 bits are written out followed by 5 microseconds of data (with the clock set at 200k), finally followed by the second data group (5 microseconds of data). It then looks like REQ1 stays high for 2-4 ms after the second group of 32 bits is written out before going low. Anyhow if you are trying to clock this data into a storage device I would expect to see rising clock edges when both the first and second group of data appear on DIOA0-A7..DIOD0-D7. I monitored all the other control lines pclk1,2 ack1 and did not see signal levels other than 0, again I do not have the DIO card connected to anything except a logic analyzer. Would you know if it is typical to use REQ1 as a clock input to a storage device or if this can be done?

Fan how to tell if it works? What test can I do? G62-a17SA

G62-a17SA
HP G62-a17SA
Windows 7 64 bit
How to tell if the fan works? it works when Laptop powered up, but no other times.
I've had it less than a year, and customer services, wont fix it unless I mail the receipt, which I cant find. i called the next day and said I will pay for it to be looked at, and replaced if needed. The price was £223.94. Which is 51% of the price I paid for the laptop originally, so I left it.
I need to know if my laptop is save to use. It can get hot, I'm worried it could start a fire. The fan only comes on when I boot the laptop up, no other times. What software can I use to tests to see if it functions properly? then I know if i will have to pay to send it away. (not a dust or venting problem) also its a instant sudden one
Please help
Oliver
This question was solved.
View Solution.

HP G62-a17SA
Windows 7 64 bit
How to tell if the fan works? it works when Laptop powered up, but no other times.
I've had it less than a year, and customer services, wont fix it unless I mail the receipt, which I cant find. i called the next day and said I will pay for it to be looked at, and replaced if needed. The price was £223.94. Which is 51% of the price I paid for the laptop originally, so I left it.
I need to know if my laptop is save to use. It can get hot, I'm worried it could start a fire. The fan only comes on when I boot the laptop up, no other times. What software can I use to tests to see if it functions properly? then I know if i will have to pay to send it away. (it's not dust or venting problems)
Please help
Oliver

[Forum FAQ] How to tell if the DAC port is automatically changed or not

Introduction
Per Books Online:
http://msdn.microsoft.com/en-us/library/ms189595.aspx
SQL Server listens for the DAC on TCP port 1434 if available or a TCP port dynamically assigned upon Database Engine startup.
Also, we can go to the following registry to specify the DAC port number manually:
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Microsoft SQL Server\MSSQL11.MSSQLSERVER\MSSQLServer\SuperSocketNetLib\AdminConnection\Tcp
The error log contains the port number the DAC is listening on. Besides looking at the error log, how to find which port is used by DAC connection and how to tell if the DAC port is manually set by us or assigned automatically by SQL Server?
Solution
The following query can be used to check if there is an existing DAC connection and it also give us the port number used by dedicated admin connection.
SELECT name,local_tcp_port FROM sys.dm_exec_connections ec
join sys.endpoints e
on (ec.endpoint_id=e.endpoint_id)
WHERE e.name='Dedicated Admin Connection'
Here is the scenario to test if the DAC port is automatically changed or not.
There are two instances are running on one server. I specified the same DAC port number 5555 for the two SQL Server instances by modifying the registry
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Microsoft SQL Server\MSSQL11.MSSQLSERVER\MSSQLServer\SuperSocketNetLib\AdminConnection\Tcp
Opened the DAC connection to instance 1. Executed the above query, it returns the result:
name
local_tcp_port
Dedicated Admin Connection 5555
Then, opened a DAC connection to instance 2. It throw out the following error message:
Sqlcmd: Error: Microsoft SQL Server Native Client 11.0 : Client unable to establish connection because an error was encountered during handshakes before login.
Common causes include client attempting to connect to an unsupported version of SQL Server, server too busy to accept new connections or a resource limitation (memory or maximum allowed connections) on the server..
Sqlcmd: Error: Microsoft SQL Server Native Client 11.0 : TCP Provider: An established connection was aborted by the software in your host machine..
Sqlcmd: Error: Microsoft SQL Server Native Client 11.0 : Client unable to establish connection.
Sqlcmd: Error: Microsoft SQL Server Native Client 11.0 : Client unable to establish connection due to prelogin failure.
The above error message was thrown out because the DAC port number 5555 was not available for instance 2 which was occupying by instance 1. After restarting the SQL Server engine service of instance 2, if checking in the registry, you would see a new DAC port
number has been assigned to the second instance.
Then, the DAC connection to instance 2 succeed this time and executed the above query, it returned the same port number which is same as the one in the registry key and the port number was assigned automatically.
DAC port will not change even SQL Server service is restarted only if the TCP port is available.
More Information
http://msdn.microsoft.com/en-us/library/ms189595.aspx
Applies to
SQL Server 2012
Please click to vote if the post helps you. This can be beneficial to other community members reading the thread.

I tested your script after
establishing a DAC connection from SSMS 2014. It worked as described. Thank you.
SELECT name,local_tcp_port FROM sys.dm_exec_connections ec
join sys.endpoints e
on (ec.endpoint_id=e.endpoint_id)
WHERE e.name='Dedicated Admin Connection'
name local_tcp_port
Dedicated Admin Connection 1434
Kalman Toth Database & OLAP Architect
SQL Server 2014 Design & Programming
New Book / Kindle: Exam 70-461 Bootcamp: Querying Microsoft SQL Server 2012

I am using the G Drive Slim to back up my files, but I don't know how to tell if or when it is finished. The white light does not change, flicker, go out, etc. When is it finished?

The whole story: The hard drive on my quite new Mac Book Pro, bought in December of 2011, crashed and burned in the Fall of 2012. I purchased a new hard drive and was informed that the only way I could have saved my "stuff" was to back it up with an external hard drive. Who knew?? I bought a G Drive Slim at the Apple store, and on their advice. BUT I really don't understand how to use it, and the instructions are completely inadequate. How can you tell when it is finished? I have educated myself on the proper way to eject the Drive, but I don't know how to tell if it is done. Or, frankly, if it is even doing anything. The white light burns steadily, no blinking, no flickering. Nothing. Thanks for help.

are you backing up files, or doing a Time machine backup, either way, the Time machine will STOP when finished and show "last backup at XXXXXX" meaning its done...... OR if when transferring files, it will show a progress bar on your desktop and vanish when files are copied.
Open up the Hitachi drive (your G drive is made by Hitachi, and the best made by the way).....and see if the files are there.
a MORE VISUAL way is to open the hard drive file, and drag and drop files INTO the Gdrive and you can see them visually be copied there as you do it.
To see your HD on your desktop GOTO FINDER......PREFERENCES....then GENERAL TAB.........check the box marked HARD DRIVES.........then your Gdrive will appear on your desktop........open it from there, and DRAG and drop files from anywhere INTO the Gdrive....... easy visual way to see the files being copied into the Gdrive.

How to tell if multiple files are selected when they are opened in windows

Hello, can someone help me, my question is how to tell if multiple file selections were made when they were opened (right-click->open). Through modifying the registry I already have my Java program start up when a file with specific extension is double-clicked.
The problem is when multiple files are opened at the same time, an instance of java program is created and run for each of the selected files. Ideally I would like it so that only one instance of java program is run, regardless of the number of selections.
When you try it with Microsoft media player or winamp for example, it seems that only one process is created and run (I don't see many processes spawning when I watch it using task manager). Maybe this is more of Windows issue rather than Java programming issue. Any help is appreciated.

If anybody wants to know, this can be solved by either 1) using DDE 2) using DropTarget (from Windows) 3) make a light-weight EXE dispatcher (eg. in C), and use file to have IPC between the dispatcher (which gets the filepath for each of the selections) and the java program. There can be other methods of course. Using the second option is the simplest but it requires WinXP and higher. I implemented it using option 3.. the downside of this is there's a warning message pop up when trying to open many (>20?) files at the same time by Windows. However, option 1 'seems' to have the same limitation. Having a java program created each time for each of the selections seems to be too slow, for viable option.

HT201302 I am trying to upload pictures from my phone to my computer and I'm getting an error message that a photo is corrupted so it can't download. I don't know how to tell which of the photos is corrupted so that I can delete it and try again? Thanks

I am trying to upload pictures from my phone to my computer and I'm getting an error message that a photo is corrupted so it can't download. I don't know how to tell which of the photos is corrupted so that I can delete it and try again? Thanks!

If this is an iCloud account the Outbox only appears when sending an email, so if it is still trying I suppose it should be showing now (not sure though, hard to replicate this)
What type of email account?

I had to get a new iphone and want to know how to tell if my pictures from my previous phone were backed up on itunes. when i connect my c even if i'm going from a 4 to a 5s?

i had to get a new iphone and want to know how to tell if my pictures from my previous phone were backed up on itunes. when i connect to itunes, does it automatically sync / backup even if i'm going from a 4 w/IOS 6 to a 5S w/IOS 7?

Welcome to the Apple Community.
Yes you can probably delete the 2 incomplete back ups they are unlikely to work.
However, I'd be inclined to back up to a computer as well and restore from there, if you are changing your phone.

My iphone got wet how do i get it to work again- it won't turn on.

Got caught in a rainstorm and my iPhone got wet-- how do I get it to turn on again...it won't turn on? I've already tried putting it in rice for 2 days and nothing. Any other suggestions?

Let it dry for a week or so.
If you have tried to charge it or turn it on, then the damage is likely done

Nano a little wet - how to tell if dead?

Similar Messages

Maybe you are looking for