NAT and secondary IP

We got a new block of 10 ip addresses from our ISP. The five we had were
not enough. We are no longer using the original five. I binded the new IP
address to the public interface and put in the public to private addresses
in the NAT table but it won't let me add the public addresses into the
secondary IP table. It gives me an "illegal address" message. It worked
fine before, only thing different other than the new ip addresses is the
new block is on a different subnet than the original five. The BM server
hits the internet just fine. Tried adding the secondary address from a
console prompt and got an error. NAT is set up for static and dynamic. Any
insight would be greatly appreciated.

It should work. You can add a second binding, and if that goes OK, you
should be able to add the secondary IP addresses at the console prompt.
Check your subnet masks closely, in case you made a mistake and
overlapped something.
See tip #51 at the URL below.
Craig Johnson
Novell Support Connection SysOp
*** For a current patch list, tips, handy files and books on
BorderManager, go to http://www.craigjconsulting.com ***

Similar Messages

NAT proxy and secondary IP

Hello!
I have 2 NIC on my BM38SP5 box
Internal has 1 IP
External has 2 IP (primary and secondary)
I am using dynamic NAT.
Now dinamic NAT and proxy use one IP address together - primary.
I want make dynamic NAT use one external IP (primary) and proxy use another
external IP - seconadary (some billing reasons)
How can I do that thing?
WBR, Viktor

Thanks, Craig
"Craig Johnson" <[email protected]> ???????/???????? ? ????????
?????????: news:[email protected]..
> In article <BQlii.2059$[email protected]>, Tanin Viktor
> wrote:
>> I want make dynamic NAT use one external IP (primary) and proxy use
>> another
>> external IP - seconadary (some billing reasons)
>>
>> How can I do that thing?
>>
> You cannot make dynamic NAT use one, and proxy use a different address,
> for
> outbound browsing. Basically, the proxy will send on the primary public
> IP
> address.
>
> You CAN use static NAT to map one internal host to the secondary public
> address. OR, you can set up a generic or reverse proxy to listen on the
> secondary public address for inbound connections.
>
> Craig Johnson
> Novell Support Connection SysOp
> *** For a current patch list, tips, handy files and books on
> BorderManager, go to http://www.craigjconsulting.com ***
>
>

Difference between primary eindex and secondary index?

hi experts
pls answer me
difference between primary eindex and secondary index?
rewads apply.
thanks.
naresh.

hi,
check this link.
http://help.sap.com/saphelp_47x200/helpdata/en/cf/21eb2d446011d189700000e8322d00/frameset.htm
A difference is made between Primary & Secondary indexes to a table. the primary index consists of the key fields of the table and a pointer to the non-keys-fields of the table. The Primary index is generated automatically when a table is created and is created in the datebase as the same times as the table. It is also possible to define further indexes to a table in the ABAP/4 dictionary, which are then referred to as Secondary indexes.
Always it is not mandatory that an index should have all the key fields of a table. To see the index of a table
goto SE11->specify table name->click on the indexes... button on the application toolbar.
Based on your requirement you can you any of those index fields in the where clause of your query. Always its a better practice to use the index fields in the order specified. While selecting the records from a table it is always better to select the fields in the same order as specified in the table.

Need help with sorting records in primary and secondary databases

Hi,
I would like to store data into primary and secondary db in different order. For the main primary, I want it to be ordered by login_ts instead of uuid which is the key.
For the user secondary database, I want it to be ordered by sip_user. For the timestampe secondary db, I want it to be ordered by login_ts.
This is what I have right now,
this is for main
uuid=029ae227-a188-4ba8-aea4-7cbc26783d6 sip_user=200003 login_ts=1264327630 logout_ts=
uuid=22966f76-8c8a-4ab4-b832-b36e8f8e14d sip_user=200003 login_ts=1264327688 logout_ts=
uuid=e1846e4a-e1f5-406d-b903-55905a2533a sip_user=200003 login_ts=1264327618 logout_ts=
uuid=e2f9a3cb-02d1-47ff-8af8-a3a371e20b5 sip_user=200003 login_ts=1264327613 logout_ts=
this is for user search
uuid=029ae227-a188-4ba8-aea4-7cbc26783d6 sip_user=200003 login_ts=1264327630 logout_ts=
uuid=22966f76-8c8a-4ab4-b832-b36e8f8e14d sip_user=200003 login_ts=1264327688 logout_ts=
uuid=e1846e4a-e1f5-406d-b903-55905a2533a sip_user=200003 login_ts=1264327618 logout_ts=
uuid=e2f9a3cb-02d1-47ff-8af8-a3a371e20b5 sip_user=200003 login_ts=1264327613 logout_ts=
this is for timestamp
uuid=029ae227-a188-4ba8-aea4-7cbc26783d6 sip_user=200003 login_ts=1264327630 logout_ts=
uuid=22966f76-8c8a-4ab4-b832-b36e8f8e14d sip_user=200003 login_ts=1264327688 logout_ts=
uuid=e1846e4a-e1f5-406d-b903-55905a2533a sip_user=200003 login_ts=1264327618 logout_ts=
uuid=e2f9a3cb-02d1-47ff-8af8-a3a371e20b5 sip_user=200003 login_ts=1264327613 logout_ts=
but what I want is :
this is for main
uuid=e2f9a3cb-02d1-47ff-8af8-a3a371e20b5 sip_user=200003 login_ts=1264327613 logout_ts=
uuid=e1846e4a-e1f5-406d-b903-55905a2533a sip_user=200004 login_ts=1264327618 logout_ts=
uuid=029ae227-a188-4ba8-aea4-7cbc26783d6 sip_user=200003 login_ts=1264327630 logout_ts=
uuid=22966f76-8c8a-4ab4-b832-b36e8f8e14d sip_user=200005 login_ts=1264327688 logout_ts=
this is for user search
uuid=e2f9a3cb-02d1-47ff-8af8-a3a371e20b5 sip_user=200003 login_ts=1264327613 logout_ts=
uuid=029ae227-a188-4ba8-aea4-7cbc26783d6 sip_user=200003 login_ts=1264327630 logout_ts=
uuid=e1846e4a-e1f5-406d-b903-55905a2533a sip_user=200004 login_ts=1264327618 logout_ts=
uuid=22966f76-8c8a-4ab4-b832-b36e8f8e14d sip_user=200004 login_ts=1264327688 logout_ts=
this is for timestamp
uuid=e2f9a3cb-02d1-47ff-8af8-a3a371e20b5 sip_user=200003 login_ts=1264327613 logout_ts=
uuid=e1846e4a-e1f5-406d-b903-55905a2533a sip_user=200003 login_ts=1264327618 logout_ts=
uuid=029ae227-a188-4ba8-aea4-7cbc26783d6 sip_user=200004 login_ts=1264327630 logout_ts=
uuid=22966f76-8c8a-4ab4-b832-b36e8f8e14d sip_user=200004 login_ts=1264327688 logout_ts=
Right now, I have:
int compare_login_ts(dbp, a, b)
     DB *dbp;
     const DBT a, b;
     int time_a = 0;
     int time_b = 0;
     time_a = atoi ( (char *)a->data);
     time_b = atoi ( (char *)b->data);
     return time_a - time_b ;
for the timestamp secondary, I set that compare function:
          if ((ret = (*sdb)->set_bt_compare(*sdb , compare_login_ts )) != 0){
Does anyone know how can I make it sorted according?

Hi,
The DB->set_bt_compare() is used to compare keys in Btree database. In the callback function, both the DBTs are key, but not data. Please refer to http://www.oracle.com/technology/documentation/berkeley-db/db/api_reference/C/dbset_bt_compare.html.
If you want any field in the data to be sorted, you might create a secondary index on it and define the compare function as you wish.
Regards,
Emily Fu, Oracle Berkeley DB

Using Open DNS etc with a Verizon and secondary router

I have a Airport Extreme Base Station setup in Bridge Mode to the Verizon router. How do I add or replace the DNS server to Open DNS etc?

You need to set your desired DNS servers in the Actiontec since that is your DHCP server. When the AEBS is in bridge mode, its DHCP server is disabled.
Login to the Actiontec
Click on the My Network icon
Select Network Connections from the left menu
Select Broadband coax or Broadband ethernet as appropriate.
Click on Settings
Across from DNS Server, select "Use the following DNS Server addresses" from the pulldown.
Enter the primary and secondary DNS Server addresses for OpenDNS.
Click Apply.

Excise Duty, Cess and Secondary Cess not displaying in J1IIN

Dear Frnds,
I need a solution for Excise Duty, Cess and Secondary Cess not displaying in J1IIN ( WHILE EXCISE ) but in Invoice it is calculated correctly., ( ie., i need CENVAT Posted, not utilized
after excise invoice generated )
kindly suggest me...
Thanks & Regards
T.Arulvanan

HI.
Plz check the forllowing settings,
IMG - Logistic General - Tax on Goods Mvt - India - Basic Settings -
1. Maintain Excise Registrations -
Check Proper Indicator for Cess and other settings.
2. Maintain Company Code Settings
3. Maintain Plant Settings
4. Maintain Excise Groups
5. Maintain Series Groups
6. Maintain Excise Duty Indicators
-- Determination of Excise Duty
7. Select Tax Calculation Procedure
--Condition-Based Excise Determination
8. Define Tax code and assign it to company code
Properly maintiain fallowing settings and try again..
Prashant

I want to use Back to my mac. When I try to turn it on, it says "Back to My Mac may be slow because more than one device on your network is providing network services. Turn off NAT and DHCP on one of the devices and try again." How do I fix this?

Not sure if I am doing this right. This is my first time in the support community.
I imagine what I put in my heading was supposed to go in here.
I want to use Back to my mac. When I try to turn it on, it says "Back to my mac may be slow because more than one device on your network is providing network services. Turn off NAT and DHCP on one of the devices and try again. See the documentation that came with your device for information about turning off network services"
Does anyone know how I do this? I contacted my ISP (Telus in Canada) and they did not know anything (not that they usually do).

Why do ISPs insist upon making things so difficult for their customers?
If you cannot get them to understand that you would prefer to use your own router over their piece of cheap junk, perhaps the information in the following will be useful:
http://keithbalomben.wordpress.com/2012/03/29/telus-actiontec-v1000h-hacks-and-i nformation/
Scroll down to DHCP Settings
You will need to log in with proper "technician" credentials. They are provided in the above link as
Username: tech
Password: t3lu5tv
... but these may or may not work. Try it, and if you cannot get anywhere at least now you know what to ask Telus to do in return for your business.

Using modem Sagem f@st 3464 (Scarlet One : vdsl tv VoIP wi-fi) : impossible to create a new Wi-Fi network (2.4 or 5 GHz) ? Conflict with DHCP / NAT and so on. No answer from the Apple help desk, Air Port Utility 6.1 unusable (configuration = Win 7)

Good afternoon,
My internet connection is delivered by a modem Sagem f@st 3464 (Scarlet One : vdsl tv VoIP wi-fi), it's almost the same than a BBox-2 from Belgacom (software and configuration).
This modem has 4 ethernet port, 2 for TV, 2 for LAN, the WAN port is RJ-11 and the connection is a PPPoE (in fact, it's the Belgacom network). I also got a Wi-Fi 802.11g on it.
The main raison why I bought a TC is the dual Wi-Fi 2.4 GHz and 5 GHz (for 802.11n), especially for my MacBook Pro and my iPad 3.
First of all, can I do the following with my TC :
1) connecting the TC using a ethernet cable from one of the two modem's LAN ports to the TC's WAN port
2) create a new Wi-Fi network using the TC ?
Up to now, after 2 man days of configuration, my TC is connected to my existing LAN network, as a bridge, but there is no new Wi-Fi network.
The Airport Utility 6.1 "Wizard" is just un-usable and I need to use a Win 7 laptop in order to get access to all the configuration !
The standard manual is very poor.
Does someone already create a new Wi-Fi network using its TC connected by Ethernet on a modem/router device ? How do you set up the DHCP (and NAT) ? Which range did you use ?
Sincerely yours,
AVDB

1) connecting the TC using a ethernet cable from one of the two modem's LAN ports to the TC's WAN port
2) create a new Wi-Fi network using the TC ?
Does someone already create a new Wi-Fi network using its TC connected by Ethernet on a modem/router device ? How do you set up the DHCP (and NAT) ? Which range did you use ?
This is easy enough to do..
Plug the TC directly into a computer.. without other connections to do the setup.
Using the newly installed 5.6 utility.
Bridge the TC.
Create a wireless network.
This is an older screen shot and I would set security to WPA2 Personal only not WPA/WPA2 Personal as shown above.
I do recommend you use wireless names that are short, no spaces, pure alphanumeric.
Update the TC..
Now plug it into the modem router.. it will be a part of the network without doing NAT and DHCP itself.. which you do not want.. that leads to double NAT issues.. but it is a WAP that provides access to devices on both 2.4ghz and 5ghz bands directly to the main router.

Howto: Zones in private subnets using ipfilter's NAT and Port forwarding

This setup supports the following features:
* Requires 1 Network interface total.
* Supports 1 or more public ips.
* Allows Zone to Zone private network traffic.
* Allows internet access from the global zones.
* Allows direct (via ipfilter) internet access to ports in non-global zones.
(change networks to suit your needs, the number of public and private ip was lowered to simplify this doc)
Network setup:
iprb0 65.38.103.1/24
defaultrouter 65.38.103.254
iprb0:1 192.168.1.1/24 (in global zone)
Create a zone on iprb0 with an ip of 192.168.1.2
### Example /etc/ipf/ipnat.conf
# forward from a public port to a private zone port
rdr iprb0 65.38.103.1/32 port 2222 -> 192.168.1.2 port 22
# force outbound zone traffic thru a certain ip address
# required for mail servers because of reverse lookup
map iprb0 192.168.1.2/32 -> 65.38.103.1/32 proxy port ftp ftp/tcp
map iprb0 192.168.1.2/32 -> 65.38.103.1/32 portmap tcp/udp auto
map iprb0 192.168.1.2/32 -> 65.38.103.1
# allow any 192.168.1.x zone to use the internet
map iprb0 192.168.1.0/24 -> 0/32 proxy port ftp ftp/tcp
map iprb0 192.168.1.0/24 -> 0/32 portmap tcp/udp auto
map iprb0 192.168.1.0/24 -> 0/32For testing purposes you can leave /etc/ipf/ipf.conf empty.
Be aware the you must "svcadm disable ipfilter; svcadm enable ipfilter" to reload rules and the rules stay loaded if they are just disabled(bug).
Zones can't modify their routes and inherit the default routes of the global zone. Because of this we have to trick the non-global zones into using a router that doesn't exist.
Create /etc/init.d/zone_route_hack
Link this file to /etc/rc3.d/S99zone_route_hack.
#/bin/sh
# based on information found at
# http://blogs.sun.com/roller/page/edp?entry=using_branded_zones_on_a
# http://forum.sun.com/jive/thread.jspa?threadID=75669&messageID=275741
fake_router=192.168.1.254
public_net=65.38.103.0
router=`netstat -rn | grep default | grep -v " $fake_router " | nawk '{print $2}'`
# send some data to the real network router so we look up it's arp address
ping -sn $router 1 1 >/dev/null
# record the arp address of the real router
router_arp=`arp $router | nawk '{print $4}'`
# delete any existing arp address entry for our fake private subnet router
arp -d $fake_router >/dev/null
# assign the real routers arp address to our fake private subnet router
arp -s $fake_router $router_arp
# route our private subnet through our fake private subnet router
route add default $fake_router
# Can't create this route until the zone/interface are loaded
# Adjust this based on your hardware and number of zones
sleep 300
# Duplicate this line for every non-global zone with a private ip that
# will have ipfilter rdr (redirects) pointing to it
route add -net $public_net 192.168.1.2 -ifaceNow we have both public and private ip addresses on our one iprb0 interface. If we'd really like our private zone network to really be private we don't want any non-NAT'ed 192.168.1.x traffic leaving the interface. Since ipfilter can't block traffic between zones because they use loopbacks we can just block the 192.168.1.x traffic and the zones can still talk.
The following /etc/ipf/ipf.conf defaults to deny.
# ipf.conf
# IP Filter rules to be loaded during startup
# See ipf(4) manpage for more information on
# IP Filter rules syntax.
# INCOMING DEFAULT DENY
block in all
block return-rst in proto tcp all
# two open ports one of which is redirected in ipnat.conf
pass in quick on iprb0 proto tcp from any to any port = 22 flags S keep state keep frags
pass in quick on iprb0 proto tcp from any to any port = 2222 flags S keep state keep frags
# INCOMING PING
pass in quick on iprb0 proto icmp from any to 65.38.103.0/24 icmp-type 8 keep state
# INCOMING GLOBAL ZONE UNIX TRACEROUTE FIX PART 1
#pass in quick on iprb0 proto udp from any to 65.38.103.0/24 keep state
# OUTGOING RULES
block out all
# ALL INTERNAL TRAFFIC STAYS INTERNAL (Zones use non-filtered loopback)
# remove/edit as needed to actually talk to local private physical networks
block out quick from any to 192.168.0.0/16
block out quick from any to 172.16.0.0/12
block out quick from any to 10.0.0.0/8
block out quick from any to 0.0.0.0/8
block out quick from any to 127.0.0.0/8
block out quick from any to 169.254.0.0/16
block out quick from any to 192.0.2.0/24
block out quick from any to 204.152.64.0/23
block out quick from any to 224.0.0.0/3
# Allow traffic out the public interface on the public address
pass out quick on iprb0 from 65.38.103.1/32 to any flags S keep state keep frags
# OUTGOING PING
pass out quick on iprb0 proto icmp from 65.38.103.1/32 to any icmp-type 8 keep state
# Allow traffic out the public interface on the private address (needs nat and router arp hack)
pass out quick on iprb0 from 192.168.1.0/24 to any flags S keep state keep frags
# OUTGOING PING
pass out quick on iprb0 proto icmp from 192.168.1.0/24 to any icmp-type 8 keep state
# INCOMING TRACEROUTE FIX PART 2
#pass out quick on iprb0 proto icmp from 65.38.103.1/32 to any icmp-type 3 keep stateIf you want incoming and outgoing internet in your zones it is easier if you just give them public ips and setup a firewall in the global zone. If you have limited public ip address(I'm setting up a colocation 1u server) then you might take this approach. One of the best things about doing thing this way is that any software configured in the non-global zones will never be configured to listen on an ip address that might change if you change public ips.

Instead of using the script as a legacy_run script, set it up in SMF.
First create the file /var/svc/manifest/system/ip-route-hack.xml with
the following
---Start---
<?xml version="1.0"?>
<!DOCTYPE service_bundle SYSTEM
"/usr/share/lib/xml/dtd/service_bundle.dtd.1">

<service_bundle type='manifest' name='NATtrans:ip-route-hack'>
<service
name='system/ip-route-hack'
type='service'
version='1'>
<create_default_instance enabled='true' />
<single_instance />
<dependency
name='physical'
grouping='require_all'
type='service'
restart_on='none'>
<service_fmri value='svc:/network/physical:default' />
</dependency>
<dependency
name='loopback'
grouping='require_all'
type='service'
restart_on='none'>
<service_fmri value='svc:/network/loopback:default' />
</dependency>
<exec_method
type='method'
name='start'
exec='/lib/svc/method/svc-ip-route-hack start'
timeout_seconds='0' />
<property_group name='startd' type='framework'>
<propval name='duration' type='astring'
value='transient' />
</property_group>
<stability value='Unstable' />
<template>
<common_name>
<loctext xml:lang='C'>
Hack to allow zone to NAT translate.
</loctext>
</common_name>
<documentation>
<manpage
title='zones'
section='1M'
manpath='/usr/share/man' />
</documentation>
</template>
</service>
</service_bundle>
---End---
then modify /var/svc/manfiest/system/zones.xml and add the following
dependancy
---Start---
<dependency
name='inet-ip-route-hack'
type='service'
grouping='require_all'
restart_on='none'>
<service_fmri value='svc:/system/ip-route-hack' />
</dependency>
---End---
Finally create the file /lib/svc/method/svc-ip-route-hack with the
contents of S99zone_route_hack, minus the sleep timer (perms 0755). Run
'svccfg import /var/svc/manifest/system/ip-route-hack.xml' and 'svccfg
import /var/svc/manifest/system/zones.xml'.
This will guarantee that ip-route-hack is run before zones are started,
but after the interfaces are brought on line. It is worth noting that
zones.xml may get overwritten during a patch, so if it suddenly stops
working, that could be why.

Static NAT and same IP address for two interfaces

We have a Cisco ASA 5520 and in order to conserve public IP addresses and configuration (possibly) can we use the same public IP address for a static NAT with two different interfaces? Here is an example of what I'm refering too where 10.10.10.10 would be the same public IP address.
static (inside,Outside) 10.10.10.10 access-list inside_nat_static_1
static (production,Outside) 10.10.10.10 access-list production_nat_static_1
Thanks for any help.
Jeff

Hi Jeff,
Unfortunately this cannot be done, on the ASA packet classification is done on the basis of mac-address, destination nat and route, and here you are confusing the firewall, to which interface does the ip belong to. I haven't ever tried to do it, but it should cause you issues.
Thanks,
Varun Rao
Security Team,
Cisco TAC

How to set security group as primary site collection admin and secondary site collection admin using powershell in sharepoint online site - office 365?

How to set security group as primary site collection admin and secondary site collection admin using powershell in sharepoint online site - office 365?

Hi,
According to your description, my understanding is that you want to set security group as admin of primary and secondary site collection using PowerShell command in office 365.
I suggest you can use the command below to set the group to site owner, then it will have the site collection admin permission.
Set-SPOSite -Identity https://contoso.sharepoint.com/sites/site1 -Owner [email protected] -NoWait
Here are some detailed articles for your reference:
https://technet.microsoft.com/en-us/library/fp161394(v=office.15)
http://blogs.realdolmen.com/experts/2013/08/16/managing-sharepoint-online-with-powershell/
Thanks
Best Regards
Jerry Guo
TechNet Community Support

BED, E Cess and Secondary education cess not showing in MIGO

Dear Experts,
i have created one PO with tax code ,
in the invoice tab all the BED,ED cess and secondary cess are showing properly,
but when i am doing the MIGO, the same is not showing in item detail excise item tab,
my tax procedure is TAXINN,
please advice me where the required settings are missed out,
lakshmi reddy

Hi,
For the above condition for that tax code u have to maintain settoff
SETOFF Must Be Maintained:-
                                          JMX1 --     IN: A/P BED setoff
                                          JEX1 ---      Ecess Setoff Sta
          JHX1     IN: A/P SECess SOTot
and also in spro in codition based classification in cin setting
u must maintain taxinn with the setoff like JMX1 and all other.
Hope Help U !
Regards,
Pardeep Malik

CESS AND SECONDARY ECESS NOT PRINTING IN ARE 1 FORM

Dear CIN gurus,
In export process . ARE 1 generation Cess and Secondary Hr Edu cess not printing. Using standard output type .
Even though Cess and ECESS appearing in ARE 1 Document in system, its not updating in outputs.
Can you suggest some guidelines to resolve this issue
regards
Jaffar.k

Hi Jaffar,
Please seach for the SAP NOTE in the service market place which are available for ECS and SHECess, Once you apply these relevant notes your issue will be resolved. As currently I dont remember the Note number, Please seach in service market place.
hope this information will help you.
Regards
MBS

Exchange rate variances between Primary and Secondary Ledger

We have a little problem on our hands.....we are implementing dual ledgers with dynamic posting, primary in Canadian Dollar and secondary in USD.
Exchange rate variances would occur if for example, we consider material transactions at different points in time. We would have no problems in the primary. However, CAD to USD exchange rates are updated monthly and very likely, rates would change month to month. Therefore, exchange rate variances would happen frequently in the secondary ledger.
We have been asked by senior management how these variances would be handled by EBS. Just wondering if you have ideas though we are looking into the accounting events in SLA.
Thanks,
Sanjib

If the requirement was to maintain balance in USD and Canadian dollar, You can use the Reporting currency option instead of Secondary ledger.
Regards,
Chirag

Magic Mouse Primary and Secondary Clicks Switched

Recently I picked up a Magic Mouse and have since found some very strange things that I don't know how to fix:
The primary and secondary clicks are switched. As in, under mouse settings when I select the secondary click to be on the right, only the primary click works on the right side and everything else is a secondary click. It is also very annoying because every time I have more than one finger touching the surface it counts as a secondary click. If anyone knows how to fix this I would really appreciate feedback.
I looked around in settings and couldn't find anything regarding this matter. I fiddled with some stuff but never got it working properly.
Feedback much appreciated!
--Justin

Looking at another thread in this forum, I see some people who had older apple mice installed before the magic mouse are having this problem with the magic mouse.
I had an older wireless mouse that would take right-clicks before I set up the magic mouse. Unfortunately when I connect the older wireless mouse I can no longer access it's preferences. It only gives me the preferences a generic one button mouse. Somewhere there must be some set of files I can delete and it will forget this old mouse.
I am pretty disheartened after a week of this. One of the benefits to a mac is that I shouldn't have to dig around removing drivers and such

NAT and secondary IP

Similar Messages

Maybe you are looking for