NAT issue in ASA 5510
HI experts,
i am using
Cisco Adaptive Security Appliance Software Version 8.0(4)
Device Manager Version 6.4(9)
i configure Nat but when i use packet tracer in firewall to see packet flow i found my inside packet is not able to reach to outside interface.what is the problem i don't understand. should i create access rule for the or anything else.
please healpe..
regards
Suhas
Hi,
Pease find the whole configuration & packet tracer screen shot..
ASA Version 8.0(4)
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 172.16.30.0 outside
interface Ethernet0/0
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Ethernet0/1
nameif outside
security-level 0
ip address 172.16.30.2 255.255.255.0
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 0
ip address 10.10.10.1 255.255.255.0
boot system disk0:/
boot system disk0:/asa825-33-k8.bin
ftp mode passive
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu management 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-649-103.bin
no asdm history enable
arp timeout 14400
nat-control
global (outside) 1 interface
nat (inside) 1 192.168.1.0 255.255.255.0
route outside 0.0.0.0 0.0.0.0 172.16.30.1 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.10 255.255.255.255 inside
http 10.10.10.2 255.255.255.255 management
no snmp-server location
no snmp-server contact
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet 192.168.1.10 255.255.255.255 inside
telnet timeout 5
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
username cisco password 3USUcOPFUiMCO4Jk encrypted
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
message-length maximum client auto
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
Cryptochecksum:0fbad53e0533429878e448f1f87415fc
: end
ciscoasa(config)#
This image for INSIDE HOST TO INSIDE INTERFACE
This image for INSIDE HOST TO OUTSIDE INTERFACE
This image for INSIDE HOST TO OUTSIDE NEXT HOP INTERFACE
Similar Messages
-
Having issues on ASA 5510 pass traffic between interfaces
I am trying to pass traffic between two internal interfaces but am unable to. Been searching quite a bit and have tried several things to no avail. I feel like there is a simple solution here I am just not seeing. Here is the relevant portion of my config:
interface Ethernet0/1
nameif inside
security-level 100
ip address 192.168.5.1 255.255.255.0
interface Ethernet0/2
nameif ct-users
security-level 100
ip address 10.12.0.1 255.255.0.0
same-security-traffic permit inter-interface
access-list inside_nat0_outbound extended permit ip any 192.168.5.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 10.12.0.0 255.255.0.0
access-list inside_access_in extended permit ip any any
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
nat (ct-users) 0 access-list inside_nat0_outbound
nat (ct-users) 1 0.0.0.0 0.0.0.0
static (inside,ct-users) 192.168.5.0 192.168.5.0 netmask 255.255.255.0
static (ct-users,inside) 10.12.0.0 10.12.0.0 netmask 255.255.0.0
access-group outside_access_in in interface outside
access-group outside_access_ipv6_in in interface outside
access-group inside_access_in in interface inside
access-group inside_access_ipv6_in in interface inside
access-group inside_access_in in interface ct-users
access-group inside_access_ipv6_in in interface ct-users
On both networks I am able to access the internet, just not traffic between each other.
A packet-tracer reveals the following (it's hitting some weird rules on the way):
cybertron# packet-tracer input inside tcp 192.168.5.2 ssh 10.12.0.2 ssh detailed
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
Forward Flow based lookup yields rule:
in id=0xab827020, priority=1, domain=permit, deny=false
hits=8628156090, user_data=0x0, cs_id=0x0, l3_type=0x8
src mac=0000.0000.0000, mask=0000.0000.0000
dst mac=0000.0000.0000, mask=0100.0000.0000
Phase: 2
Type: UN-NAT
Subtype: static
Result: ALLOW
Config:
static (ct-users,inside) 10.12.0.0 10.12.0.0 netmask 255.255.0.0
match ip ct-users 10.12.0.0 255.255.0.0 inside any
static translation to 10.12.0.0
translate_hits = 0, untranslate_hits = 6
Additional Information:
NAT divert to egress interface ct-users
Untranslate 10.12.0.0/0 to 10.12.0.0/0 using netmask 255.255.0.0
Phase: 3
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group inside_access_in in interface inside
access-list inside_access_in extended permit ip any any
Additional Information:
Forward Flow based lookup yields rule:
in id=0xad5bec88, priority=12, domain=permit, deny=false
hits=173081, user_data=0xa8a76ac0, cs_id=0x0, flags=0x0, protocol=0
src ip=0.0.0.0, mask=0.0.0.0, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
Phase: 4
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0xab829758, priority=0, domain=inspect-ip-options, deny=true
hits=146139764, user_data=0x0, cs_id=0x0, reverse, flags=0x0, protocol=0
src ip=0.0.0.0, mask=0.0.0.0, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
Phase: 5
Type: NAT-EXEMPT
Subtype: rpf-check
Result: ALLOW
Config:
Additional Information:
Forward Flow based lookup yields rule:
in id=0xad48c860, priority=6, domain=nat-exempt-reverse, deny=false
hits=2, user_data=0xad4b5e98, cs_id=0x0, use_real_addr, flags=0x0, protocol=0
src ip=192.168.5.0, mask=255.255.255.0, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
Phase: 6
Type: NAT-EXEMPT
Subtype:
Result: ALLOW
Config:
match ip inside any ct-users 10.12.0.0 255.255.0.0
NAT exempt
translate_hits = 2, untranslate_hits = 2
Additional Information:
Forward Flow based lookup yields rule:
in id=0xad3b1f70, priority=6, domain=nat-exempt, deny=false
hits=2, user_data=0xad62b7a8, cs_id=0x0, use_real_addr, flags=0x0, protocol=0
src ip=0.0.0.0, mask=0.0.0.0, port=0
dst ip=10.12.0.0, mask=255.255.0.0, port=0, dscp=0x0
Phase: 7
Type: NAT
Subtype:
Result: ALLOW
Config:
static (inside,ct-users) 192.168.5.0 192.168.5.0 netmask 255.255.255.0
match ip inside 192.168.5.0 255.255.255.0 ct-users any
static translation to 192.168.5.0
translate_hits = 1, untranslate_hits = 15
Additional Information:
Forward Flow based lookup yields rule:
in id=0xadf7a778, priority=5, domain=nat, deny=false
hits=6, user_data=0xad80cfd0, cs_id=0x0, flags=0x0, protocol=0
src ip=192.168.5.0, mask=255.255.255.0, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
Phase: 8
Type: NAT
Subtype: host-limits
Result: ALLOW
Config:
static (inside,outside) udp 184.73.2.1 1514 192.168.5.2 1514 netmask 255.255.255.255
match udp inside host 192.168.5.2 eq 1514 outside any
static translation to 184.73.2.1/1514
translate_hits = 0, untranslate_hits = 0
Additional Information:
Forward Flow based lookup yields rule:
in id=0xab8e2928, priority=5, domain=host, deny=false
hits=9276881, user_data=0xab8e1d20, cs_id=0x0, reverse, flags=0x0, protocol=0
src ip=192.168.5.2, mask=255.255.255.255, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
Phase: 9
Type: NAT
Subtype: rpf-check
Result: ALLOW
Config:
static (ct-users,inside) 10.12.0.0 10.12.0.0 netmask 255.255.0.0
match ip ct-users 10.12.0.0 255.255.0.0 inside any
static translation to 10.12.0.0
translate_hits = 0, untranslate_hits = 6
Additional Information:
Forward Flow based lookup yields rule:
out id=0xad158dc0, priority=5, domain=nat-reverse, deny=false
hits=6, user_data=0xac0fb6b8, cs_id=0x0, flags=0x0, protocol=0
src ip=0.0.0.0, mask=0.0.0.0, port=0
dst ip=10.12.0.0, mask=255.255.0.0, port=0, dscp=0x0
Phase: 10
Type: NAT
Subtype: host-limits
Result: ALLOW
Config:
static (ct-users,inside) 10.12.0.0 10.12.0.0 netmask 255.255.0.0
match ip ct-users 10.12.0.0 255.255.0.0 inside any
static translation to 10.12.0.0
translate_hits = 0, untranslate_hits = 6
Additional Information:
Reverse Flow based lookup yields rule:
in id=0xada0cd38, priority=5, domain=host, deny=false
hits=131, user_data=0xac0fb6b8, cs_id=0x0, reverse, flags=0x0, protocol=0
src ip=10.12.0.0, mask=255.255.0.0, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
Phase: 11
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Reverse Flow based lookup yields rule:
in id=0xad5c1ab0, priority=0, domain=inspect-ip-options, deny=true
hits=130, user_data=0x0, cs_id=0x0, reverse, flags=0x0, protocol=0
src ip=0.0.0.0, mask=0.0.0.0, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0, dscp=0x0
Phase: 12
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 189385494, packet dispatched to next module
Module information for forward flow ...
snp_fp_tracer_drop
snp_fp_inspect_ip_options
snp_fp_tcp_normalizer
snp_fp_translate
snp_fp_adjacency
snp_fp_fragment
snp_ifc_stat
Module information for reverse flow ...
snp_fp_tracer_drop
snp_fp_inspect_ip_options
snp_fp_translate
snp_fp_tcp_normalizer
snp_fp_adjacency
snp_fp_fragment
snp_ifc_stat
Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: ct-users
output-status: up
output-line-status: up
Action: allowhow are you testing? if you are pinging between the subnets, make sure you have disabled windows firewall and/or any other firewall that is installed on the PCs (remember to re-enable it later).
Are the NAT commands there because you were trying different things to get this working? I suggest you use the command no nat-control instead. Depending on the version of ASA you are running it may already be disabled by default. In version 8.4 and later nat-control has been removed completely.
Please remember to select a correct answer and rate helpful posts -
Hello Experts,
We have recently installed new 5525 8.6(1) ASA's. Our setup is like; where wer are using Public IP for web server, which needs to be mapped/natted to internet VIP address and that VIP is configured on F5 LB. Setup is below; This Public IP is the webserver IP. The firewall get hits, but web server page is not being displayes. In the logs FW built tcp but then tear down the session, syslog id (302014) 77 TCP Reset-I
|INTERNET|
|
|
195.201.55.X
[ ASA ]
Natting to
10.100.100.151
[ F5 ]
|
Real Servers---> .150 .151
NAT Config is;
nat (DMZ1,OUTSIDE) source static 10.100.100.151 195.201.55.X
Your help will be appreciated if you can provide the right nat config;
RegardsHi Jouni,
The packet tracer looks good, all green tick boxes. I need to install wireshark on the Servers to makesure they are getting request from the Firewall.
The funny thing is, on the firewall if I change the NAT say, from public IP translate to the real IP of the servers, then it works perfectly. But as soon as I change the NAT rule i.e Public IP translate to the VIP address, then it doesn't bring up the webpage. though I can ping the VIP address from the firewall, and the VIP address is the same subnet as the FW and F5 boxes with /24 mask! e.g FW int ip is 10.100.100.1 and F5 connecting to FW is 10.100.100.3 and the VIP is
10.100.100.151/24.
Akshy,
On the FW I did the TCP Ping, but It doesn't work. Like I said, I will install wireshark on the server and then will see if it works.
Many thanks guys for your quick response and help. I will let you know the result.
Regards -
Hi All,
Hoping someone can clear this up for me.
I am trying to setup a ASA 5510 with IOS 9.1 and having NAT issues.
The ASA is connected inside the LAN to separate a second LAN.
Internal (10.0.0.0/24) --> DG RTR (10.0.0.254) FE0/0--> FE0/1 (61.0.0.1/24) --> ASA outside (61.0.0.2/24) --> ASA Inside (192.168.1.0//24)
I keep getting Asymetric NAT rules matched for forward and reverse path flows when going from Internal to ASA Inside LAN
I fear it is my lack of understanding, when you have a router you can go between different LANs/subnets but with the ASA does it always NAT whatever happens?
If I statically NAT a device on the ASA Inside LAN I can get to the device via the 61.0.0.0 address and if I add what I believe to be an exemption rule to keep the translated packet the same as long as I specify something like Internal LAN to ASA Inside specific device it works but not if I do Internal LAN to ASA Inside LAN.
Hope that makes sense and someone can give me a clue to where I am going wrong with the setup / understanding.
If there are any good docs that might explain it would be appreciated as everything I have read so far has not given me an clarity.
Many thanksHi,
Just to clarify, are we talking about a situation the ASA is simply connected to an internal network (even though it might use public IP addresses)? Also, do you want to perform any NAT on this ASA or is there some separate firewall sitting at the edge of your network handling the external connectivity?
If the above things are true then you could simply leave your ASA NAT configuration totally blank and the ASA would not do any NAT to the traffic. This naturally would require that you make sure that routing for subnet 192.168.1.0/24 is handled on all the routers/devices on the network as this subnet would be directly visible with its original addresses (since we would leave the ASA NAT configuration blank). I manage a couple of environments where the customer has a internal ASA separating certain section of the LAN network and they dont have any NAT configurations.
The problems you mention in the post are probably due to Dynamic PAT configuration which means that your LAN can access the other parts of the Internal network but no connection is possible from the Internal network to this separate LAN behind the ASA. The reason there is that the connection from Internal LAN to the separate LAN wont match any NAT configuration but the return traffic (reverse check that the ASA does) will match the Dynamic PAT and that is why the traffic is dropped.
Static NAT done to the hosts behind the ASA will naturally help since there wont be any problems with the translation in that case in either direction.
You could take a look at a NAT Document I wrote way back in 2013. Though it wont really answer your specific questions here but perhaps it might be of help at some point
https://supportforums.cisco.com/document/132066/asa-nat-83-nat-operation-and-configuration-format-cli
Hope this helps :)
- Jouni -
ASA 5510 - Setting up ACL to permit access only to the Nat'ed subnet
Hi,
I experiencing an issue in setting up an ACL on my ASA 5510 to permit access only to the Nat subnet from inside to the outside interface. This firewall is setup for the DR solution in the production network. I am applying following acl in the inbound direction on the inside interface.
permit ip any "Nat_subnet"
After appliying this acl to inside interface I observed that I can ping to the destinations in NAT'ed subnet but unable to ssh to the servers. Following is the summary of my configuration. I would appreciate if someone please advice to resolve this issue.
Regards,
Muds
interface Ethernet0/0
nameif outside
security-level 0
ip address 192.168.135.241 255.255.255.248 standby 192.168.135.242
interface Ethernet0/1
nameif inside
security-level 100
ip address 192.168.135.249 255.255.255.248 standby 192.168.135.250
object-group network d1-dr-nat_nets
network-object 192.168.128.0 255.255.248.0
object network 10.210.14.0_Net
nat (outside,inside) static 192.168.128.0_Net
object network 10.210.16.0_Net
nat (outside,inside) static 192.168.129.0_Net
object network 10.210.80.0_Net
nat (outside,inside) static 192.168.130.0_Net
object network 10.210.84.0_Net
nat (outside,inside) static 192.168.131.0_Net
object network 10.210.86.0_Net
nat (outside,inside) static 192.168.132.0_Net
object network 10.210.88.0_Net
nat (outside,inside) static 192.168.133.0_Net !
object network 10.210.14.0_Net
nat (outside,inside) static 192.168.128.0_Net
object network 10.210.16.0_Net
nat (outside,inside) static 192.168.129.0_Net
object network 10.210.80.0_Net
nat (outside,inside) static 192.168.130.0_Net
object network 10.210.84.0_Net
nat (outside,inside) static 192.168.131.0_Net
object network 10.210.86.0_Net
nat (outside,inside) static 192.168.132.0_Net
object network 10.210.88.0_Net
nat (outside,inside) static 192.168.133.0_Net
access-list prod_lan-in extended permit ip any object-group d1-dr-nat_nets
access-group prod_lan-in in interface insideHi,
As I mentioned even though you NAT the address from outside to inside you will have to use the REAL IP ADDRESSES in the access-list statements
Your hosts on inside will still be connecting to the NAT IP address of the hosts on outside BUT the ASA needs the ACL statements with the NATed hosts original IP addresses
Let me give an simple example
object network STATIC
host 10.10.10.10
nat (outside,inside) static 192.168.10.10
access-list INSIDE-IN permit ip any host 10.10.10.10
or
access-list INSIDE-IN permit ip any object STATIC
- Jouni -
ASA 5510 - Version 8.2(1) - SSH, ICMP and NAT not working
I have an ASA 5510 using version 8.2(1) and I have enabled ssh, icmp and they work from the inside network but not from the outside network.
Further to this, I exposed one site from the inside interface on the ASA (192.168.1.100) to outside (1.1.1.7) using NAT and it is not pingable nor accessible from the outside. I also allowed SSH from the outside network to the external IP addresses of the ASA and it is not working either. Any ideas what I could be missing in my configuration? I bolded the configurations involved in the ASA running configuration I copied below (please note I have replaced the real IP addresses with 1.1.1.x and 2.2.2.x):
ASA Version 8.2(1)
hostname fw
domain-name net.com
enable password eYKAfQL1.ZSbcTXZ encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
dns-guard
interface Ethernet0/0
description Primary Outside (Internet)
speed 10
duplex full
nameif outside
security-level 0
ip address 1.1.1.5 255.255.255.240
ospf cost 10
interface Ethernet0/1
description inside
speed 100
duplex full
nameif inside
security-level 100
ip address 192.168.1.254 255.255.255.0
ospf cost 10
interface Ethernet0/2
description WLAN
nameif WLAN
security-level 100
ip address 192.168.108.240 255.255.255.0
ospf cost 10
interface Ethernet0/3
description Secondary Outside (Internet)
speed 100
duplex full
nameif WAN2
security-level 0
ip address 2.2.2.133 255.255.255.192
interface Management0/0
description LAN/STATE Failover Interface
time-range after_hours
periodic weekdays 7:00 to 23:00
boot system disk0:/asa821-k8.bin
no ftp mode passive
clock timezone EST -5
clock summer-time EDT recurring
dns domain-lookup WLAN
dns server-group DefaultDNS
retries 3
timeout 5
name-server 8.8.8.8
name-server 206.191.0.210
name-server 4.2.2.1
name-server 4.2.2.2
domain-name net.com
access-list WAN2_access_in extended permit icmp any any echo-reply
access-list WAN2_access_in extended permit icmp any any time-exceeded
access-list WAN2_access_in extended permit icmp any any source-quench
access-list WAN2_access_in extended permit icmp any any unreachable
access-list WLAN_access_in extended permit icmp any any echo-reply
access-list WLAN_access_in extended permit icmp any any time-exceeded
access-list WLAN_access_in extended permit icmp any any source-quench
access-list WLAN_access_in extended permit icmp any any unreachable
access-list WLAN_access_in extended permit tcp host 192.168.1.100 eq ssh any
access-list WLAN_access_in extended permit tcp 192.168.1.0 255.255.255.0 host 192.168.1.100 eq ssh
access-list WLAN_access_in extended permit ip any any
access-list time_based extended permit ip any any time-range after_hours
access-list split_tunnel standard permit host 206.191.0.210
access-list split_tunnel standard permit host 206.191.0.140
access-list split_tunnel standard permit host 207.181.101.4
access-list split_tunnel standard permit host 207.181.101.5
access-list split_tunnel standard permit 192.168.1.0 255.255.255.0
access-list outside_access_in extended permit icmp any any echo-reply
access-list outside_access_in extended permit icmp any any time-exceeded
access-list outside_access_in extended permit icmp any any
access-list outside_access_in extended permit tcp any host 1.1.1.7 eq ssh
access-list inside_access_in extended permit ip any any
access-list inside_access_in extended permit tcp any host 192.168.1.100 eq ssh
access-list inside_access_in extended permit icmp any any
access-list inside_access_in extended permit icmp 192.168.1.0 255.255.255.0 any
access-list inside_access_in extended permit ip 192.168.1.0 255.255.255.0 any
access-list inside_access_in extended permit tcp 192.168.1.0 255.255.255.0 host 192.168.1.100 eq ssh
pager lines 20
logging enable
logging asdm informational
mtu outside 1500
mtu inside 1500
mtu WLAN 1500
mtu WAN2 1500
ip local pool DHCP 192.168.1.245-192.168.1.252 mask 255.255.255.0
ip verify reverse-path interface outside
ip verify reverse-path interface WAN2
failover
failover lan unit secondary
failover lan interface FO Management0/0
failover key *****
failover link FO Management0/0
failover interface ip FO 192.168.255.171 255.255.255.0 standby 192.168.255.172
icmp unreachable rate-limit 1 burst-size 1
icmp permit any outside
icmp permit any inside
icmp permit any WLAN
icmp permit any WAN2
asdm image disk0:/asdm-621.bin
asdm history enable
arp timeout 14400
global (outside) 1 interface
global (WAN2) 1 interface
nat (inside) 1 192.168.1.0 255.255.255.0
nat (WLAN) 1 192.168.108.0 255.255.255.0
static (inside,outside) 1.1.1.7 192.168.1.100 netmask 255.255.255.255
access-group outside_access_in in interface outside
access-group inside_access_in in interface inside
access-group WLAN_access_in in interface WLAN
access-group WAN2_access_in in interface WAN2
route outside 0.0.0.0 0.0.0.0 1.1.1.1 1
route WAN2 0.0.0.0 0.0.0.0 2.2.2.129 254
route inside 192.168.1.100 255.255.255.255 192.168.1.0 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable
http 192.168.108.0 255.255.255.0 WLAN
http 192.168.1.0 255.255.255.0 inside
http 192.168.1.101 255.255.255.255 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
sla monitor 123
type echo protocol ipIcmpEcho 4.2.2.2 interface outside
num-packets 3
timeout 1000
frequency 3
service resetoutside
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
track 1 rtr 123 reachability
no vpn-addr-assign aaa
no vpn-addr-assign dhcp
telnet timeout 5
ssh scopy enable
ssh 2.2.2.132 255.255.255.255 outside
ssh 69.17.141.134 255.255.255.255 outside
ssh 192.168.1.0 255.255.255.0 inside
ssh 192.168.1.100 255.255.255.255 inside
ssh 192.168.108.0 255.255.255.0 WLAN
ssh timeout 60
console timeout 0
management-access inside
dhcpd address 192.168.108.11-192.168.108.239 WLAN
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp authenticate
ntp server 128.100.100.128
ntp server 132.246.168.148
ntp server 128.100.56.135
tftp-server inside 192.168.1.100 /
webvpn
group-policy Wifi internal
group-policy Wifi attributes
wins-server none
dns-server value 206.191.0.210 206.191.0.140
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
split-tunnel-policy tunnelspecified
split-tunnel-network-list value split_tunnel
tunnel-group Wifi type remote-access
tunnel-group Wifi general-attributes
address-pool DHCP
default-group-policy Wifi
tunnel-group Wifi ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
inspect icmp
inspect icmp error
policy-map type inspect dns migrated_dns_map_1
parameters
message-length maximum 512
service-policy global_policy global
prompt hostname context
Cryptochecksum:ac25ef0642e0ecb8f0ef63219833f3ae
: end
asdm image disk0:/asdm-621.bin
asdm location 192.168.1.245 255.255.255.255 inside
asdm location 192.168.1.252 255.255.255.255 inside
asdm history enableHi,
I can't see any problems right away in the configuration.
I guess we could start by using the "packet-tracer" to simulate the SSH and ICMP through the firewall
packet-tracer input outside tcp 1.1.1.1 12345 22
packet-tracer input outside icmp 1.1.1.1 8 0
Don'd mind the source address of 1.1.1.1. Its just an address that is located behind "outside" interface according to the ASA routing table. (As the configurations 1.1.1.0/28 is not actually configured on the ASA)
Share the exact "packet-tracer" command used (wihtout the public IP, notice that the output contains the public IP also) and the output of the command with us here.
Also, have you made sure that there is no old translations active on the ASA?
You can use this command to view those
show xlate local 192.168.1.100
You can clear the xlates with
clear xlate local 192.168.1.100
- Jouni -
ASA 5510 anti spam module issue need help
hi all,
i have ASA5510 my E0 interface is having public ip and E1 is having 192.168.1.0/24 network and my DMZ E2 is 172.16.2.0/24 network.
my management interface ip address is 10.10.10.1 and ive put 10.10.10.5 for SSM module. but im not receiving the updates from net bcoz there is no connection to the internet from 10.10.10.0/24 network.
how can i do that, and ASA 5510 has got 4 ports E0,E1,E2,E3 but i can see that port E3 is activated if i chk the sh run there is no port E3.
now my issue is i would like to allow 10.10.10.0/24 to access internet to update the module.
pls help, i will rate all the posts.
Regards
Binoy.Try these links:
http://www.cisco.com/en/US/products/ps6120/products_configuration_guide_chapter09186a0080636f70.html#wp1051819
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a00807335ca.shtml -
Can any one help me out how to resolve this issue.
ASA 8.4 version
inside to TEST working fine.
nat (inside,TEST) source dynamic interface
my main concern is TEST (192.168.2.1) lan wants to access inside subnets with real ip addresses (ex: 11.11.11.1) with RDP connection.
please share the configuration.Hi Rajesh,
Do you expect router 11.11.11.1 to respond for your RDP connection?? or you want the pc behind that router if any to respond to your rdp connection??
Please put your present configuration and describe your question with more details on what do you want to achieve with this sample setup..... hopefully we will try to provide better suggestions to you....
Regards
Karthik -
Problems with the new NAT in ASA 5510 (8.4)
Hi together,
i have some problems with the NAT statements in ASA Version 8.4.
What i want is to translate the internal address of a server to the external address with a NAT rule.
The ASA has only one WAN connection (named outside)
The internal server has the ip address 192.168.0.221 (as example) and i want to translate all incoming traffic on port 3389 to the Server (192.168.0.221).
This is only for training, i dont want to forward a 3389 port into the BAD in a productive Network
first i create the network object for the inside server (192.168.0.221)
object network Network_Obj_RDP
host 192.168.0.221
After that i create the access rule for incoming traffic on outside interface:
access-list outside_access_in extended permit ip any any log debugging
Next i create a access rule for the inside-prod network to allow the traffic to the RDP Server:
access-list inside-prod_access_in extended permit object RDP interface outside object Network_Obj_RDP
Now i create the NAT rule in the network object (Network_Obj_RDP):
object network Network_Obj_RDP
nat (inside-prod,outside) static interface service tcp 3389 3389
But if i want to connect via 3389 on the outside interface i see in the syslog this entry:
Built inbound TCP connection 23248 for outside:80.187.107.132/7445 (80.187.107.132/7445) to inside-prod:192.168.0.221/3389 (External IP/3389)
After a while the connection will be teardown with this message:
Teardown TCP connection 23289 for outside:80.187.107.132/2294 to inside-prod:192.168.0.221/3389 duration 0:00:30 bytes 0 SYN Timeout
It looks like that the acl works fine, but the NAT translation are wrong...
perhaps somebody has a idea to fix this
Looking forward and hope for help...
Many thanks
GreetingsHi Jouni,
this is the correct Packet Tracer output i think:
packet-tracer input inside-prod tcp 192.168.0.220 3389 8.8.8.8 4567
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
MAC Access list
Phase: 2
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 0.0.0.0 0.0.0.0 outside
Phase: 3
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group inside-prod_access_in in interface inside-prod
access-list inside-prod_access_in extended permit ip object Network_Obj-Productiv any log debugging
Additional Information:
Phase: 4
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 5
Type: NAT
Subtype:
Result: ALLOW
Config:
object network Network_Obj_RDP
nat (inside-prod,outside) static interface service tcp 3389 3389
Additional Information:
Static translate 192.168.0.220/3389 to 80.146.252.162/3389
Phase: 6
Type: USER-STATISTICS
Subtype: user-statistics
Result: ALLOW
Config:
Additional Information:
Phase: 7
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 8
Type: USER-STATISTICS
Subtype: user-statistics
Result: ALLOW
Config:
Additional Information:
Phase: 9
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 825, packet dispatched to next module
Result:
input-interface: inside-prod
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: allow
That looks preety fine, but the way back isn´t right:
packet-tracer input outside tcp 8.8.8.8 4567 192.168.0.220 3389
Phase: 1
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 192.168.0.0 255.255.255.0 inside-prod
Phase: 2
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 0.0.0.0 0.0.0.0 outside
Phase: 3
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group outside-in in interface outside
access-list outside-in extended permit tcp any object Network_Obj_RDP eq 3389 log debugging
Additional Information:
Phase: 4
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 5
Type: VPN
Subtype: ipsec-tunnel-flow
Result: ALLOW
Config:
Additional Information:
Phase: 6
Type: NAT
Subtype: rpf-check
Result: DROP
Config:
object network Network_Obj_RDP
nat (inside-prod,outside) static interface service tcp 3389 3389
Additional Information:
Result:
input-interface: outside
input-status: up
input-line-status: up
output-interface: inside-prod
output-status: up
output-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule
I have no idea... -
ASA 5510 with Cisco 2811 Router Behind it - Not forwarding traffic
Hi all,
Some might know that I have been dealing with an issue where I cannot seem to get forwarded packets to reach their destinations behind an ASA 5510 that has a Cisco 2811 connected directly behind it.
Some examples that work.
I can SSH into the ASA.
I can SSH to the Cisco Routers behind the ASA.
I cannot reach items beind the Cisco Routers.
My Configuration is this (I am sure I included a bunch of info I didn't need to, but I am hoping it'll help!):
I have a static Ip assigned to my Ouside Interface Ethernet 0/1
It has an IP address of 199.195.xxx.xxx
I am trying to learn how to shape network traffic (this is all new to me) via the ASA and the Routers to specific devices.
The Inside Interface on the ASA is 10.10.1.1 255.255.255.252
The Outside Interface on the 2811 is 10.10.1.2 255.255.255.252
I can ping the router from the ASA. I can SSH through the ASA to the router.
BUT I CANNOT ACCESS DEVICES BEHIND THE ROUTER.
So, I wanted to BAM that statement above because I just don't kjnow where the issue is. Is the issue on the router or the ASA, my guess is, the router, but I just don't know.
Here are my configs, helpfully someone can help.
ASA errors on the ASDM when I try and hit resources; specifically a web device behind the ASA and the 2811. It's Ip address 192.168.1.5 it's listening on port 80.Static IP, not assigned via DHCP.
6
Feb 14 2014
19:38:56
98.22.121.x
41164
192.168.1.5
80
Built inbound TCP connection 1922859 for Outside:98.22.121.x/41164 (98.22.121.x/41164) to Inside:192.168.1.5/80 (199.195.168.x/8080)
6
Feb 14 2014
19:38:56
10.10.1.2
80
98.22.121.x
41164
Deny TCP (no connection) from 10.10.1.2/80 to 98.22.121.x/41164 flags SYN ACK on interface Inside
ASA5510# sh nat
Auto NAT Policies (Section 2)
1 (DMZ) to (Outside) source static ROUTER-2821 interface service tcp ssh 2222
translate_hits = 1, untranslate_hits = 18
2 (Inside) to (Outside) source static ROUTER-2811 interface service tcp ssh 222
translate_hits = 0, untranslate_hits = 13
3 (VOIP) to (Outside) source static ROUTER-3745 interface service tcp ssh 2223
translate_hits = 0, untranslate_hits = 3
4 (Inside) to (Outside) source static RDP-DC1 interface service tcp 3389 3389
translate_hits = 0, untranslate_hits = 236
5 (Inside) to (Outside) source static WEBCAM-01 interface service tcp www 8080
translate_hits = 0, untranslate_hits = 162
Manual NAT Policies (Section 3)
1 (any) to (Outside) source dynamic PAT-SOURCE interface
translate_hits = 1056862, untranslate_hits = 83506
ASA5510# show access-list
access-list cached ACL log flows: total 0, denied 0 (deny-flow-max 4096)
alert-interval 300
access-list USERS; 1 elements; name hash: 0x50681c1e
access-list USERS line 1 standard permit 10.10.1.0 255.255.255.0 (hitcnt=0) 0xdd6ba495
access-list Outside_access_in; 5 elements; name hash: 0xe796c137
access-list Outside_access_in line 1 extended permit tcp host 98.22.121.x object ROUTER-2811 eq ssh (hitcnt=37) 0x5a53778d
access-list Outside_access_in line 1 extended permit tcp host 98.22.121.x host 10.10.1.2 eq ssh (hitcnt=37) 0x5a53778d
access-list Outside_access_in line 2 extended permit tcp host 98.22.121.x object ROUTER-2821 eq ssh (hitcnt=8) 0x9f32bc21
access-list Outside_access_in line 2 extended permit tcp host 98.22.121.x host 10.10.0.2 eq ssh (hitcnt=8) 0x9f32bc21
access-list Outside_access_in line 3 extended permit tcp host 98.22.121.x interface Outside eq https (hitcnt=0) 0x385488b2
access-list Outside_access_in line 4 extended permit tcp host 98.22.121.x object WEBCAM-01 eq www (hitcnt=60) 0xe66674ec
access-list Outside_access_in line 4 extended permit tcp host 98.22.121.x host 192.168.1.5 eq www (hitcnt=60) 0xe66674ec
access-list Outside_access_in line 5 extended permit tcp host 98.22.121.x object RDP-DC1 eq 3389 (hitcnt=3) 0x02f13f4e
access-list Outside_access_in line 5 extended permit tcp host 98.22.121.x host 192.168.1.2 eq 3389 (hitcnt=3) 0x02f13f4e
access-list dmz-access-vlan1; 1 elements; name hash: 0xc3450860
access-list dmz-access-vlan1 line 1 extended permit ip 128.162.1.0 255.255.255.0 any (hitcnt=0) 0x429fedf1
access-list dmz-access; 3 elements; name hash: 0xf53f5801
access-list dmz-access line 1 remark Permit all traffic to DC1
access-list dmz-access line 2 extended permit ip 128.162.1.0 255.255.255.0 host 192.168.1.2 (hitcnt=0) 0xd2dced0a
access-list dmz-access line 3 remark Permit only DNS traffic to DNS server
access-list dmz-access line 4 extended permit udp 128.162.1.0 255.255.255.0 host 192.168.1.2 eq domain (hitcnt=0) 0xbb21093e
access-list dmz-access line 5 remark Permit ICMP to all devices in DC
access-list dmz-access line 6 extended permit icmp 128.162.1.0 255.255.255.0 192.168.1.0 255.255.255.0 (hitcnt=0) 0x71269ef7
CISCO-2811#show access-lists
Standard IP access list 1
10 permit any (1581021 matches)
CISCO-2811#show translate
CISCO-2811#show route
CISCO-2811#show route-map
CISCO-2811#show host
CISCO-2811#show hosts
Default domain is maladomini.int
Name/address lookup uses domain service
Name servers are 192.168.1.2, 199.195.168.4, 205.171.2.65, 205.171.3.65, 8.8.8.8
Codes: UN - unknown, EX - expired, OK - OK, ?? - revalidate
temp - temporary, perm - permanent
NA - Not Applicable None - Not defined
Host Port Flags Age Type Address(es)
api.mixpanel.com None (temp, OK) 2 IP 198.23.64.21
198.23.64.22
198.23.64.18
198.23.64.19
198.23.64.20
ASA5510:
ASA5510# sh run all
: Saved
ASA Version 9.1(4)
command-alias exec h help
command-alias exec lo logout
command-alias exec p ping
command-alias exec s show
terminal width 80
hostname ASA5510
domain-name maladomini.int
enable password x encrypted
no fips enable
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
xlate per-session permit tcp any4 any4
xlate per-session permit tcp any4 any6
xlate per-session permit tcp any6 any4
xlate per-session permit tcp any6 any6
xlate per-session permit udp any4 any4 eq domain
xlate per-session permit udp any4 any6 eq domain
xlate per-session permit udp any6 any4 eq domain
xlate per-session permit udp any6 any6 eq domain
passwd x encrypted
names
dns-guard
lacp system-priority 32768
interface Ethernet0/0
description LAN Interface
speed auto
duplex auto
no flowcontrol send on
nameif Inside
security-level 100
ip address 10.10.1.1 255.255.255.252
delay 10
interface Ethernet0/1
description WAN Interface
speed auto
duplex auto
no flowcontrol send on
nameif Outside
security-level 0
ip address 199.195.168.xxx 255.255.255.240
delay 10
interface Ethernet0/2
description DMZ
speed auto
duplex auto
no flowcontrol send on
nameif DMZ
security-level 100
ip address 10.10.0.1 255.255.255.252
delay 10
interface Ethernet0/3
description VOIP
speed auto
duplex auto
no flowcontrol send on
nameif VOIP
security-level 100
ip address 10.10.2.1 255.255.255.252
delay 10
interface Management0/0
speed auto
duplex auto
management-only
shutdown
nameif management
security-level 0
no ip address
delay 10
regex _default_gator "Gator"
regex _default_firethru-tunnel_2 "[/\\]cgi[-]bin[/\\]proxy"
regex _default_shoutcast-tunneling-protocol "1"
regex _default_http-tunnel "[/\\]HT_PortLog.aspx"
regex _default_x-kazaa-network "[\r\n\t ]+[xX]-[kK][aA][zZ][aA][aA]-[nN][eE][tT][wW][oO][rR][kK]"
regex _default_msn-messenger "[Aa][Pp][Pp][Ll][Ii][Cc][Aa][Tt][Ii][Oo][Nn][/\\][Xx][-][Mm][Ss][Nn][-][Mm][Ee][Ss][Ss][Ee][Nn][Gg][Ee][Rr]"
regex _default_GoToMyPC-tunnel_2 "[/\\]erc[/\\]Poll"
regex _default_gnu-http-tunnel_uri "[/\\]index[.]html"
regex _default_aim-messenger "[Hh][Tt][Tt][Pp][.][Pp][Rr][Oo][Xx][Yy][.][Ii][Cc][Qq][.][Cc][Oo][Mm]"
regex _default_gnu-http-tunnel_arg "crap"
regex _default_icy-metadata "[\r\n\t ]+[iI][cC][yY]-[mM][eE][tT][aA][dD][aA][tT][aA]"
regex _default_GoToMyPC-tunnel "machinekey"
regex _default_windows-media-player-tunnel "NSPlayer"
regex _default_yahoo-messenger "YMSG"
regex _default_httport-tunnel "photo[.]exectech[-]va[.]com"
regex _default_firethru-tunnel_1 "firethru[.]com"
checkheaps check-interval 60
checkheaps validate-checksum 60
boot system disk0:/asa914-k8.bin
ftp mode passive
clock timezone UTC 0
dns domain-lookup Outside
dns server-group DefaultDNS
name-server 199.195.168.4
name-server 205.171.2.65
name-server 205.171.3.65
domain-name maladomini.int
same-security-traffic permit inter-interface
object service ah pre-defined
service ah
description This is a pre-defined object
object service eigrp pre-defined
service eigrp
description This is a pre-defined object
object service esp pre-defined
service esp
description This is a pre-defined object
object service gre pre-defined
service gre
description This is a pre-defined object
object service icmp pre-defined
service icmp
description This is a pre-defined object
object service icmp6 pre-defined
service icmp6
description This is a pre-defined object
object service igmp pre-defined
service igmp
description This is a pre-defined object
object service igrp pre-defined
service igrp
description This is a pre-defined object
object service ip pre-defined
service ip
description This is a pre-defined object
object service ipinip pre-defined
service ipinip
description This is a pre-defined object
object service ipsec pre-defined
service esp
description This is a pre-defined object
object service nos pre-defined
service nos
description This is a pre-defined object
object service ospf pre-defined
service ospf
description This is a pre-defined object
object service pcp pre-defined
service pcp
description This is a pre-defined object
object service pim pre-defined
service pim
description This is a pre-defined object
object service pptp pre-defined
service gre
description This is a pre-defined object
object service snp pre-defined
service snp
description This is a pre-defined object
object service tcp pre-defined
service tcp
description This is a pre-defined object
object service udp pre-defined
service udp
description This is a pre-defined object
object service tcp-aol pre-defined
service tcp destination eq aol
description This is a pre-defined object
object service tcp-bgp pre-defined
service tcp destination eq bgp
description This is a pre-defined object
object service tcp-chargen pre-defined
service tcp destination eq chargen
description This is a pre-defined object
object service tcp-cifs pre-defined
service tcp destination eq cifs
description This is a pre-defined object
object service tcp-citrix-ica pre-defined
service tcp destination eq citrix-ica
description This is a pre-defined object
object service tcp-ctiqbe pre-defined
service tcp destination eq ctiqbe
description This is a pre-defined object
object service tcp-daytime pre-defined
service tcp destination eq daytime
description This is a pre-defined object
object service tcp-discard pre-defined
service tcp destination eq discard
description This is a pre-defined object
object service tcp-domain pre-defined
service tcp destination eq domain
description This is a pre-defined object
object service tcp-echo pre-defined
service tcp destination eq echo
description This is a pre-defined object
object service tcp-exec pre-defined
service tcp destination eq exec
description This is a pre-defined object
object service tcp-finger pre-defined
service tcp destination eq finger
description This is a pre-defined object
object service tcp-ftp pre-defined
service tcp destination eq ftp
description This is a pre-defined object
object service tcp-ftp-data pre-defined
service tcp destination eq ftp-data
description This is a pre-defined object
object service tcp-gopher pre-defined
service tcp destination eq gopher
description This is a pre-defined object
object service tcp-ident pre-defined
service tcp destination eq ident
description This is a pre-defined object
object service tcp-imap4 pre-defined
service tcp destination eq imap4
description This is a pre-defined object
object service tcp-irc pre-defined
service tcp destination eq irc
description This is a pre-defined object
object service tcp-hostname pre-defined
service tcp destination eq hostname
description This is a pre-defined object
object service tcp-kerberos pre-defined
service tcp destination eq kerberos
description This is a pre-defined object
object service tcp-klogin pre-defined
service tcp destination eq klogin
description This is a pre-defined object
object service tcp-kshell pre-defined
service tcp destination eq kshell
description This is a pre-defined object
object service tcp-ldap pre-defined
service tcp destination eq ldap
description This is a pre-defined object
object service tcp-ldaps pre-defined
service tcp destination eq ldaps
description This is a pre-defined object
object service tcp-login pre-defined
service tcp destination eq login
description This is a pre-defined object
object service tcp-lotusnotes pre-defined
service tcp destination eq lotusnotes
description This is a pre-defined object
object service tcp-nfs pre-defined
service tcp destination eq nfs
description This is a pre-defined object
object service tcp-netbios-ssn pre-defined
service tcp destination eq netbios-ssn
description This is a pre-defined object
object service tcp-whois pre-defined
service tcp destination eq whois
description This is a pre-defined object
object service tcp-nntp pre-defined
service tcp destination eq nntp
description This is a pre-defined object
object service tcp-pcanywhere-data pre-defined
service tcp destination eq pcanywhere-data
description This is a pre-defined object
object service tcp-pim-auto-rp pre-defined
service tcp destination eq pim-auto-rp
description This is a pre-defined object
object service tcp-pop2 pre-defined
service tcp destination eq pop2
description This is a pre-defined object
object service tcp-pop3 pre-defined
service tcp destination eq pop3
description This is a pre-defined object
object service tcp-pptp pre-defined
service tcp destination eq pptp
description This is a pre-defined object
object service tcp-lpd pre-defined
service tcp destination eq lpd
description This is a pre-defined object
object service tcp-rsh pre-defined
service tcp destination eq rsh
description This is a pre-defined object
object service tcp-rtsp pre-defined
service tcp destination eq rtsp
description This is a pre-defined object
object service tcp-sip pre-defined
service tcp destination eq sip
description This is a pre-defined object
object service tcp-smtp pre-defined
service tcp destination eq smtp
description This is a pre-defined object
object service tcp-ssh pre-defined
service tcp destination eq ssh
description This is a pre-defined object
object service tcp-sunrpc pre-defined
service tcp destination eq sunrpc
description This is a pre-defined object
object service tcp-tacacs pre-defined
service tcp destination eq tacacs
description This is a pre-defined object
object service tcp-talk pre-defined
service tcp destination eq talk
description This is a pre-defined object
object service tcp-telnet pre-defined
service tcp destination eq telnet
description This is a pre-defined object
object service tcp-uucp pre-defined
service tcp destination eq uucp
description This is a pre-defined object
object service tcp-www pre-defined
service tcp destination eq www
description This is a pre-defined object
object service tcp-http pre-defined
service tcp destination eq www
description This is a pre-defined object
object service tcp-https pre-defined
service tcp destination eq https
description This is a pre-defined object
object service tcp-cmd pre-defined
service tcp destination eq rsh
description This is a pre-defined object
object service tcp-sqlnet pre-defined
service tcp destination eq sqlnet
description This is a pre-defined object
object service tcp-h323 pre-defined
service tcp destination eq h323
description This is a pre-defined object
object service tcp-udp-cifs pre-defined
service tcp-udp destination eq cifs
description This is a pre-defined object
object service tcp-udp-discard pre-defined
service tcp-udp destination eq discard
description This is a pre-defined object
object service tcp-udp-domain pre-defined
service tcp-udp destination eq domain
description This is a pre-defined object
object service tcp-udp-echo pre-defined
service tcp-udp destination eq echo
description This is a pre-defined object
object service tcp-udp-kerberos pre-defined
service tcp-udp destination eq kerberos
description This is a pre-defined object
object service tcp-udp-nfs pre-defined
service tcp-udp destination eq nfs
description This is a pre-defined object
object service tcp-udp-pim-auto-rp pre-defined
service tcp-udp destination eq pim-auto-rp
description This is a pre-defined object
object service tcp-udp-sip pre-defined
service tcp-udp destination eq sip
description This is a pre-defined object
object service tcp-udp-sunrpc pre-defined
service tcp-udp destination eq sunrpc
description This is a pre-defined object
object service tcp-udp-tacacs pre-defined
service tcp-udp destination eq tacacs
description This is a pre-defined object
object service tcp-udp-www pre-defined
service tcp-udp destination eq www
description This is a pre-defined object
object service tcp-udp-http pre-defined
service tcp-udp destination eq www
description This is a pre-defined object
object service tcp-udp-talk pre-defined
service tcp-udp destination eq talk
description This is a pre-defined object
object service udp-biff pre-defined
service udp destination eq biff
description This is a pre-defined object
object service udp-bootpc pre-defined
service udp destination eq bootpc
description This is a pre-defined object
object service udp-bootps pre-defined
service udp destination eq bootps
description This is a pre-defined object
object service udp-cifs pre-defined
service udp destination eq cifs
description This is a pre-defined object
object service udp-discard pre-defined
service udp destination eq discard
description This is a pre-defined object
object service udp-domain pre-defined
service udp destination eq domain
description This is a pre-defined object
object service udp-dnsix pre-defined
service udp destination eq dnsix
description This is a pre-defined object
object service udp-echo pre-defined
service udp destination eq echo
description This is a pre-defined object
object service udp-www pre-defined
service udp destination eq www
description This is a pre-defined object
object service udp-http pre-defined
service udp destination eq www
description This is a pre-defined object
object service udp-nameserver pre-defined
service udp destination eq nameserver
description This is a pre-defined object
object service udp-kerberos pre-defined
service udp destination eq kerberos
description This is a pre-defined object
object service udp-mobile-ip pre-defined
service udp destination eq mobile-ip
description This is a pre-defined object
object service udp-nfs pre-defined
service udp destination eq nfs
description This is a pre-defined object
object service udp-netbios-ns pre-defined
service udp destination eq netbios-ns
description This is a pre-defined object
object service udp-netbios-dgm pre-defined
service udp destination eq netbios-dgm
description This is a pre-defined object
object service udp-ntp pre-defined
service udp destination eq ntp
description This is a pre-defined object
object service udp-pcanywhere-status pre-defined
service udp destination eq pcanywhere-status
description This is a pre-defined object
object service udp-pim-auto-rp pre-defined
service udp destination eq pim-auto-rp
description This is a pre-defined object
object service udp-radius pre-defined
service udp destination eq radius
description This is a pre-defined object
object service udp-radius-acct pre-defined
service udp destination eq radius-acct
description This is a pre-defined object
object service udp-rip pre-defined
service udp destination eq rip
description This is a pre-defined object
object service udp-secureid-udp pre-defined
service udp destination eq secureid-udp
description This is a pre-defined object
object service udp-sip pre-defined
service udp destination eq sip
description This is a pre-defined object
object service udp-snmp pre-defined
service udp destination eq snmp
description This is a pre-defined object
object service udp-snmptrap pre-defined
service udp destination eq snmptrap
description This is a pre-defined object
object service udp-sunrpc pre-defined
service udp destination eq sunrpc
description This is a pre-defined object
object service udp-syslog pre-defined
service udp destination eq syslog
description This is a pre-defined object
object service udp-tacacs pre-defined
service udp destination eq tacacs
description This is a pre-defined object
object service udp-talk pre-defined
service udp destination eq talk
description This is a pre-defined object
object service udp-tftp pre-defined
service udp destination eq tftp
description This is a pre-defined object
object service udp-time pre-defined
service udp destination eq time
description This is a pre-defined object
object service udp-who pre-defined
service udp destination eq who
description This is a pre-defined object
object service udp-xdmcp pre-defined
service udp destination eq xdmcp
description This is a pre-defined object
object service udp-isakmp pre-defined
service udp destination eq isakmp
description This is a pre-defined object
object service icmp6-unreachable pre-defined
service icmp6 unreachable
description This is a pre-defined object
object service icmp6-packet-too-big pre-defined
service icmp6 packet-too-big
description This is a pre-defined object
object service icmp6-time-exceeded pre-defined
service icmp6 time-exceeded
description This is a pre-defined object
object service icmp6-parameter-problem pre-defined
service icmp6 parameter-problem
description This is a pre-defined object
object service icmp6-echo pre-defined
service icmp6 echo
description This is a pre-defined object
object service icmp6-echo-reply pre-defined
service icmp6 echo-reply
description This is a pre-defined object
object service icmp6-membership-query pre-defined
service icmp6 membership-query
description This is a pre-defined object
object service icmp6-membership-report pre-defined
service icmp6 membership-report
description This is a pre-defined object
object service icmp6-membership-reduction pre-defined
service icmp6 membership-reduction
description This is a pre-defined object
object service icmp6-router-renumbering pre-defined
service icmp6 router-renumbering
description This is a pre-defined object
object service icmp6-router-solicitation pre-defined
service icmp6 router-solicitation
description This is a pre-defined object
object service icmp6-router-advertisement pre-defined
service icmp6 router-advertisement
description This is a pre-defined object
object service icmp6-neighbor-solicitation pre-defined
service icmp6 neighbor-solicitation
description This is a pre-defined object
object service icmp6-neighbor-advertisement pre-defined
service icmp6 neighbor-advertisement
description This is a pre-defined object
object service icmp6-neighbor-redirect pre-defined
service icmp6 neighbor-redirect
description This is a pre-defined object
object service icmp-echo pre-defined
service icmp echo
description This is a pre-defined object
object service icmp-echo-reply pre-defined
service icmp echo-reply
description This is a pre-defined object
object service icmp-unreachable pre-defined
service icmp unreachable
description This is a pre-defined object
object service icmp-source-quench pre-defined
service icmp source-quench
description This is a pre-defined object
object service icmp-redirect pre-defined
service icmp redirect
description This is a pre-defined object
object service icmp-alternate-address pre-defined
service icmp alternate-address
description This is a pre-defined object
object service icmp-router-advertisement pre-defined
service icmp router-advertisement
description This is a pre-defined object
object service icmp-router-solicitation pre-defined
service icmp router-solicitation
description This is a pre-defined object
object service icmp-time-exceeded pre-defined
service icmp time-exceeded
description This is a pre-defined object
object service icmp-parameter-problem pre-defined
service icmp parameter-problem
description This is a pre-defined object
object service icmp-timestamp-request pre-defined
service icmp timestamp-request
description This is a pre-defined object
object service icmp-timestamp-reply pre-defined
service icmp timestamp-reply
description This is a pre-defined object
object service icmp-information-request pre-defined
service icmp information-request
description This is a pre-defined object
object service icmp-information-reply pre-defined
service icmp information-reply
description This is a pre-defined object
object service icmp-mask-request pre-defined
service icmp mask-request
description This is a pre-defined object
object service icmp-mask-reply pre-defined
service icmp mask-reply
description This is a pre-defined object
object service icmp-traceroute pre-defined
service icmp traceroute
description This is a pre-defined object
object service icmp-conversion-error pre-defined
service icmp conversion-error
description This is a pre-defined object
object service icmp-mobile-redirect pre-defined
service icmp mobile-redirect
description This is a pre-defined object
object network ROUTER-2811
host 10.10.1.2
object network ROUTER-2821
host 10.10.0.2
object network WEBCAM-01
host 192.168.1.5
object network DNS-SERVER
host 192.168.1.2
object network ROUTER-3745
host 10.10.2.2
object network RDP-DC1
host 192.168.1.2
object-group network PAT-SOURCE
network-object 10.10.1.0 255.255.255.252
network-object 10.10.0.0 255.255.255.252
network-object 10.10.2.0 255.255.255.252
network-object 192.168.0.0 255.255.255.0
network-object 172.16.10.0 255.255.255.0
network-object 172.16.20.0 255.255.255.0
network-object 128.162.1.0 255.255.255.0
network-object 128.162.10.0 255.255.255.0
network-object 128.162.20.0 255.255.255.0
object-group network DM_INLINE_NETWORK_2
network-object host 98.22.121.x
object-group network Outside_access_in
object-group protocol DM_INLINE_PROTOCOL_1
protocol-object gre
access-list USERS standard permit 10.10.1.0 255.255.255.0
access-list Outside_access_in extended permit tcp host 98.22.121.x object ROUTER-2811 eq ssh
access-list Outside_access_in extended permit tcp host 98.22.121.x object ROUTER-2821 eq ssh
access-list Outside_access_in extended permit tcp host 98.22.121.x interface Outside eq https
access-list Outside_access_in extended permit tcp host 98.22.121.x object WEBCAM-01 eq www
access-list Outside_access_in extended permit tcp host 98.22.121.x object RDP-DC1 eq 3389
access-list dmz-access-vlan1 extended permit ip 128.162.1.0 255.255.255.0 any
access-list dmz-access remark Permit all traffic to DC1
access-list dmz-access extended permit ip 128.162.1.0 255.255.255.0 host 192.168.1.2
access-list dmz-access remark Permit only DNS traffic to DNS server
access-list dmz-access extended permit udp 128.162.1.0 255.255.255.0 host 192.168.1.2 eq domain
access-list dmz-access remark Permit ICMP to all devices in DC
access-list dmz-access extended permit icmp 128.162.1.0 255.255.255.0 192.168.1.0 255.255.255.0
pager lines 24
logging enable
logging buffer-size 4096
logging asdm-buffer-size 100
logging asdm informational
logging flash-minimum-free 3076
logging flash-maximum-allocation 1024
logging rate-limit 1 10 message 747001
logging rate-limit 1 1 message 402116
logging rate-limit 1 10 message 620002
logging rate-limit 1 10 message 717015
logging rate-limit 1 10 message 717018
logging rate-limit 1 10 message 201013
logging rate-limit 1 10 message 201012
logging rate-limit 1 1 message 313009
logging rate-limit 100 1 message 750003
logging rate-limit 100 1 message 750002
logging rate-limit 100 1 message 750004
logging rate-limit 1 10 message 419003
logging rate-limit 1 10 message 405002
logging rate-limit 1 10 message 405003
logging rate-limit 1 10 message 421007
logging rate-limit 1 10 message 405001
logging rate-limit 1 10 message 421001
logging rate-limit 1 10 message 421002
logging rate-limit 1 10 message 337004
logging rate-limit 1 10 message 337005
logging rate-limit 1 10 message 337001
logging rate-limit 1 10 message 337002
logging rate-limit 1 60 message 199020
logging rate-limit 1 10 message 337003
logging rate-limit 2 5 message 199011
logging rate-limit 1 10 message 199010
logging rate-limit 1 10 message 337009
logging rate-limit 2 5 message 199012
logging rate-limit 1 10 message 710002
logging rate-limit 1 10 message 209003
logging rate-limit 1 10 message 209004
logging rate-limit 1 10 message 209005
logging rate-limit 1 10 message 431002
logging rate-limit 1 10 message 431001
logging rate-limit 1 1 message 447001
logging rate-limit 1 10 message 110003
logging rate-limit 1 10 message 110002
logging rate-limit 1 10 message 429007
logging rate-limit 1 10 message 216004
logging rate-limit 1 10 message 450001
flow-export template timeout-rate 30
flow-export active refresh-interval 1
mtu Inside 1500
mtu Outside 1500
mtu management 1500
mtu DMZ 1500
mtu VOIP 1500
icmp unreachable rate-limit 1 burst-size 1
icmp deny any Outside
asdm image disk0:/asdm-715.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
object network ROUTER-2811
nat (Inside,Outside) static interface service tcp ssh 222
object network ROUTER-2821
nat (DMZ,Outside) static interface service tcp ssh 2222
object network WEBCAM-01
nat (Inside,Outside) static interface service tcp www 8080
object network ROUTER-3745
nat (VOIP,Outside) static interface service tcp ssh 2223
object network RDP-DC1
nat (Inside,Outside) static interface service tcp 3389 3389
nat (any,Outside) after-auto source dynamic PAT-SOURCE interface
access-group Outside_access_in in interface Outside
ipv6 dhcprelay timeout 60
router rip
network 10.0.0.0
version 2
no auto-summary
route Outside 0.0.0.0 0.0.0.0 199.195.168.113 1
route Inside 128.162.1.0 255.255.255.0 10.10.0.2 1
route Inside 128.162.10.0 255.255.255.0 10.10.0.2 1
route Inside 128.162.20.0 255.255.255.0 10.10.0.2 1
route Inside 172.16.10.0 255.255.255.0 10.10.1.2 1
route Inside 172.16.20.0 255.255.255.0 10.10.1.2 1
route Inside 192.168.1.0 255.255.255.0 10.10.1.2 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
action continue
no cts server-group
no cts sxp enable
no cts sxp default
no cts sxp default source-ip
cts sxp reconciliation period 120
cts sxp retry period 120
user-identity enable
user-identity domain LOCAL
user-identity default-domain LOCAL
user-identity action mac-address-mismatch remove-user-ip
user-identity inactive-user-timer minutes 60
user-identity poll-import-user-group-timer hours 8
user-identity ad-agent active-user-database full-download
user-identity ad-agent hello-timer seconds 30 retry-times 5
no user-identity user-not-found enable
aaa authentication ssh console LOCAL
http server enable 443
http 0.0.0.0 0.0.0.0 Inside
http 98.22.121.x 255.255.255.255 Outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
no snmp-server enable traps syslog
no snmp-server enable traps ipsec start stop
no snmp-server enable traps entity config-change fru-insert fru-remove fan-failure power-supply power-supply-presence cpu-temperature chassis-temperature power-supply-temperature chassis-fan-failure
no snmp-server enable traps memory-threshold
no snmp-server enable traps interface-threshold
no snmp-server enable traps remote-access session-threshold-exceeded
no snmp-server enable traps connection-limit-reached
no snmp-server enable traps cpu threshold rising
no snmp-server enable traps ikev2 start stop
no snmp-server enable traps nat packet-discard
snmp-server enable
snmp-server listen-port 161
fragment size 200 Inside
fragment chain 24 Inside
fragment timeout 5 Inside
no fragment reassembly full Inside
fragment size 200 Outside
fragment chain 24 Outside
fragment timeout 5 Outside
no fragment reassembly full Outside
fragment size 200 management
fragment chain 24 management
fragment timeout 5 management
no fragment reassembly full management
fragment size 200 DMZ
fragment chain 24 DMZ
fragment timeout 5 DMZ
no fragment reassembly full DMZ
fragment size 200 VOIP
fragment chain 24 VOIP
fragment timeout 5 VOIP
no fragment reassembly full VOIP
no sysopt connection timewait
sysopt connection tcpmss 1380
sysopt connection tcpmss minimum 0
sysopt connection permit-vpn
sysopt connection reclassify-vpn
no sysopt connection preserve-vpn-flows
no sysopt radius ignore-secret
no sysopt noproxyarp Inside
no sysopt noproxyarp Outside
no sysopt noproxyarp management
no sysopt noproxyarp DMZ
no sysopt noproxyarp VOIP
service password-recovery
no crypto ipsec ikev2 sa-strength-enforcement
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto ipsec security-association replay window-size 64
crypto ipsec security-association pmtu-aging infinite
crypto ipsec fragmentation before-encryption Inside
crypto ipsec fragmentation before-encryption Outside
crypto ipsec fragmentation before-encryption management
crypto ipsec fragmentation before-encryption DMZ
crypto ipsec fragmentation before-encryption VOIP
crypto ipsec df-bit copy-df Inside
crypto ipsec df-bit copy-df Outside
crypto ipsec df-bit copy-df management
crypto ipsec df-bit copy-df DMZ
crypto ipsec df-bit copy-df VOIP
crypto ca trustpool policy
revocation-check none
crl cache-time 60
crl enforcenextupdate
crypto isakmp identity auto
crypto isakmp nat-traversal 20
crypto ikev2 cookie-challenge 50
crypto ikev2 limit max-in-negotiation-sa 100
no crypto ikev2 limit max-sa
crypto ikev2 redirect during-auth
crypto ikev1 limit max-in-negotiation-sa 20
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 Inside
ssh 98.22.121.x 255.255.255.255 Outside
ssh timeout 60
ssh version 2
ssh key-exchange group dh-group1-sha1
console timeout 0
vpn-addr-assign aaa
vpn-addr-assign dhcp
vpn-addr-assign local reuse-delay 0
ipv6-vpn-addr-assign aaa
ipv6-vpn-addr-assign local reuse-delay 0
no vpn-sessiondb max-other-vpn-limit
no vpn-sessiondb max-anyconnect-premium-or-essentials-limit
no remote-access threshold
l2tp tunnel hello 60
tls-proxy maximum-session 100
threat-detection rate dos-drop rate-interval 600 average-rate 100 burst-rate 400
threat-detection rate dos-drop rate-interval 3600 average-rate 80 burst-rate 320
threat-detection rate bad-packet-drop rate-interval 600 average-rate 100 burst-rate 400
threat-detection rate bad-packet-drop rate-interval 3600 average-rate 80 burst-rate 320
threat-detection rate acl-drop rate-interval 600 average-rate 400 burst-rate 800
threat-detection rate acl-drop rate-interval 3600 average-rate 320 burst-rate 640
threat-detection rate conn-limit-drop rate-interval 600 average-rate 100 burst-rate 400
threat-detection rate conn-limit-drop rate-interval 3600 average-rate 80 burst-rate 320
threat-detection rate icmp-drop rate-interval 600 average-rate 100 burst-rate 400
threat-detection rate icmp-drop rate-interval 3600 average-rate 80 burst-rate 320
threat-detection rate scanning-threat rate-interval 600 average-rate 5 burst-rate 10
threat-detection rate scanning-threat rate-interval 3600 average-rate 4 burst-rate 8
threat-detection rate syn-attack rate-interval 600 average-rate 100 burst-rate 200
threat-detection rate syn-attack rate-interval 3600 average-rate 80 burst-rate 160
threat-detection rate fw-drop rate-interval 600 average-rate 400 burst-rate 1600
threat-detection rate fw-drop rate-interval 3600 average-rate 320 burst-rate 1280
threat-detection rate inspect-drop rate-interval 600 average-rate 400 burst-rate 1600
threat-detection rate inspect-drop rate-interval 3600 average-rate 320 burst-rate 1280
threat-detection rate interface-drop rate-interval 600 average-rate 2000 burst-rate 8000
threat-detection rate interface-drop rate-interval 3600 average-rate 1600 burst-rate 6400
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp server 24.56.178.140 source Outside prefer
ssl server-version any
ssl client-version any
ssl encryption rc4-sha1 dhe-aes128-sha1 dhe-aes256-sha1 aes128-sha1 aes256-sha1 3des-sha1
ssl certificate-authentication fca-timeout 2
webvpn
memory-size percent 50
port 443
dtls port 443
character-encoding none
no http-proxy
no https-proxy
default-idle-timeout 1800
portal-access-rule none
no csd enable
no anyconnect enable
no tunnel-group-list enable
no tunnel-group-preference group-url
rewrite order 65535 enable resource-mask *
no internal-password
no onscreen-keyboard
no default-language
no smart-tunnel notification-icon
no keepout
cache
no disable
max-object-size 1000
min-object-size 0
no cache-static-content enable
lmfactor 20
expiry-time 1
no auto-signon
no error-recovery disable
no ssl-server-check
no mus password
mus host mus.cisco.com
no hostscan data-limit
: # show import webvpn customization
: Template
: DfltCustomization
: # show import webvpn url-list
: Template
: # show import webvpn translation-table
: Translation Tables' Templates:
: PortForwarder
: banners
: customization
: url-list
: webvpn
: Translation Tables:
: fr PortForwarder
: fr customization
: fr webvpn
: ja PortForwarder
: ja customization
: ja webvpn
: ru PortForwarder
: ru customization
: ru webvpn
: # show import webvpn mst-translation
: No MS translation tables defined
: # show import webvpn webcontent
: No custom webcontent is loaded
: # show import webvpn AnyConnect-customization
: No OEM resources defined
: # show import webvpn plug-in
group-policy DfltGrpPolicy internal
group-policy DfltGrpPolicy attributes
banner none
wins-server none
dns-server none
dhcp-network-scope none
vpn-access-hours none
vpn-simultaneous-logins 3
vpn-idle-timeout 30
vpn-idle-timeout alert-interval 1
vpn-session-timeout none
vpn-session-timeout alert-interval 1
vpn-filter none
ipv6-vpn-filter none
vpn-tunnel-protocol ikev1 ikev2 l2tp-ipsec ssl-clientless
password-storage disable
ip-comp disable
re-xauth disable
group-lock none
pfs disable
ipsec-udp disable
ipsec-udp-port 10000
split-tunnel-policy tunnelall
ipv6-split-tunnel-policy tunnelall
split-tunnel-network-list none
default-domain none
split-dns none
split-tunnel-all-dns disable
intercept-dhcp 255.255.255.255 disable
secure-unit-authentication disable
user-authentication disable
user-authentication-idle-timeout 30
ip-phone-bypass disable
client-bypass-protocol disable
gateway-fqdn none
leap-bypass disable
nem disable
backup-servers keep-client-config
msie-proxy server none
msie-proxy method no-modify
msie-proxy except-list none
msie-proxy local-bypass disable
msie-proxy pac-url none
msie-proxy lockdown enable
vlan none
nac-settings none
address-pools none
ipv6-address-pools none
smartcard-removal-disconnect enable
scep-forwarding-url none
client-firewall none
client-access-rule none
webvpn
url-list none
filter none
homepage none
html-content-filter none
port-forward name Application Access
port-forward disable
http-proxy disable
sso-server none
anyconnect ssl dtls enable
anyconnect mtu 1406
anyconnect firewall-rule client-interface private none
anyconnect firewall-rule client-interface public none
anyconnect keep-installer installed
anyconnect ssl keepalive 20
anyconnect ssl rekey time none
anyconnect ssl rekey method none
anyconnect dpd-interval client 30
anyconnect dpd-interval gateway 30
anyconnect ssl compression none
anyconnect dtls compression none
anyconnect modules none
anyconnect profiles none
anyconnect ask none
customization none
keep-alive-ignore 4
http-comp gzip
download-max-size 2147483647
upload-max-size 2147483647
post-max-size 2147483647
user-storage none
storage-objects value cookies,credentials
storage-key none
hidden-shares none
smart-tunnel disable
activex-relay enable
unix-auth-uid 65534
unix-auth-gid 65534
file-entry enable
file-browsing enable
url-entry enable
deny-message value Login was successful, but because certain criteria have not been met or due to some specific group policy, you do not have permission to use any of the VPN features. Contact your IT administrator for more information
smart-tunnel auto-signon disable
anyconnect ssl df-bit-ignore disable
anyconnect routing-filtering-ignore disable
smart-tunnel tunnel-policy tunnelall
always-on-vpn profile-setting
password-policy minimum-length 3
password-policy minimum-changes 0
password-policy minimum-lowercase 0
password-policy minimum-uppercase 0
password-policy minimum-numeric 0
password-policy minimum-special 0
password-policy lifetime 0
no password-policy authenticate-enable
quota management-session 0
tunnel-group DefaultL2LGroup type ipsec-l2l
tunnel-group DefaultL2LGroup general-attributes
no accounting-server-group
default-group-policy DfltGrpPolicy
tunnel-group DefaultL2LGroup ipsec-attributes
no ikev1 pre-shared-key
peer-id-validate req
no chain
no ikev1 trust-point
isakmp keepalive threshold 10 retry 2
no ikev2 remote-authentication
no ikev2 local-authentication
tunnel-group DefaultRAGroup type remote-access
tunnel-group DefaultRAGroup general-attributes
no address-pool
no ipv6-address-pool
authentication-server-group LOCAL
secondary-authentication-server-group none
no accounting-server-group
default-group-policy DfltGrpPolicy
no dhcp-server
no strip-realm
no nat-assigned-to-public-ip
no scep-enrollment enable
no password-management
no override-account-disable
no strip-group
no authorization-required
username-from-certificate CN OU
secondary-username-from-certificate CN OU
authentication-attr-from-server primary
authenticated-session-username primary
tunnel-group DefaultRAGroup webvpn-attributes
customization DfltCustomization
authentication aaa
no override-svc-download
no radius-reject-message
no proxy-auth sdi
no pre-fill-username ssl-client
no pre-fill-username clientless
no secondary-pre-fill-username ssl-client
no secondary-pre-fill-username clientless
dns-group DefaultDNS
no without-csd
tunnel-group DefaultRAGroup ipsec-attributes
no ikev1 pre-shared-key
peer-id-validate req
no chain
no ikev1 trust-point
no ikev1 radius-sdi-xauth
isakmp keepalive threshold 300 retry 2
ikev1 user-authentication xauth
no ikev2 remote-authentication
no ikev2 local-authentication
tunnel-group DefaultRAGroup ppp-attributes
no authentication pap
authentication chap
authentication ms-chap-v1
no authentication ms-chap-v2
no authentication eap-proxy
tunnel-group DefaultWEBVPNGroup type remote-access
tunnel-group DefaultWEBVPNGroup general-attributes
no address-pool
no ipv6-address-pool
authentication-server-group LOCAL
secondary-authentication-server-group none
no accounting-server-group
default-group-policy DfltGrpPolicy
no dhcp-server
no strip-realm
no nat-assigned-to-public-ip
no scep-enrollment enable
no password-management
no override-account-disable
no strip-group
no authorization-required
username-from-certificate CN OU
secondary-username-from-certificate CN OU
authentication-attr-from-server primary
authenticated-session-username primary
tunnel-group DefaultWEBVPNGroup webvpn-attributes
customization DfltCustomization
authentication aaa
no override-svc-download
no radius-reject-message
no proxy-auth sdi
no pre-fill-username ssl-client
no pre-fill-username clientless
no secondary-pre-fill-username ssl-client
no secondary-pre-fill-username clientless
dns-group DefaultDNS
no without-csd
tunnel-group DefaultWEBVPNGroup ipsec-attributes
no ikev1 pre-shared-key
peer-id-validate req
no chain
no ikev1 trust-point
no ikev1 radius-sdi-xauth
isakmp keepalive threshold 300 retry 2
ikev1 user-authentication xauth
no ikev2 remote-authentication
no ikev2 local-authentication
tunnel-group DefaultWEBVPNGroup ppp-attributes
no authentication pap
authentication chap
authentication ms-chap-v1
no authentication ms-chap-v2
no authentication eap-proxy
class-map type inspect http match-all _default_gator
match request header user-agent regex _default_gator
class-map type inspect http match-all _default_msn-messenger
match response header content-type regex _default_msn-messenger
class-map type inspect http match-all _default_yahoo-messenger
match request body regex _default_yahoo-messenger
class-map type inspect http match-all _default_windows-media-player-tunnel
match request header user-agent regex _default_windows-media-player-tunnel
class-map type inspect http match-all _default_gnu-http-tunnel
match request args regex _default_gnu-http-tunnel_arg
match request uri regex _default_gnu-http-tunnel_uri
class-map type inspect http match-all _default_firethru-tunnel
match request header host regex _default_firethru-tunnel_1
match request uri regex _default_firethru-tunnel_2
class-map type inspect http match-all _default_aim-messenger
match request header host regex _default_aim-messenger
class-map type inspect http match-all _default_http-tunnel
match request uri regex _default_http-tunnel
class-map type inspect http match-all _default_kazaa
match response header regex _default_x-kazaa-network count gt 0
class-map type inspect http match-all _default_shoutcast-tunneling-protocol
match request header regex _default_icy-metadata regex _default_shoutcast-tunneling-protocol
class-map class-default
match any
class-map inspection_default
match default-inspection-traffic
class-map type inspect http match-all _default_GoToMyPC-tunnel
match request args regex _default_GoToMyPC-tunnel
match request uri regex _default_GoToMyPC-tunnel_2
class-map type inspect http match-all _default_httport-tunnel
match request header host regex _default_httport-tunnel
policy-map type inspect rtsp _default_rtsp_map
description Default RTSP policymap
parameters
policy-map type inspect ipv6 _default_ipv6_map
description Default IPV6 policy-map
parameters
verify-header type
verify-header order
match header routing-type range 0 255
drop log
policy-map type inspect h323 _default_h323_map
description Default H.323 policymap
parameters
no rtp-conformance
policy-map type inspect dns migrated_dns_map_1
parameters
message-length maximum client auto
message-length maximum 512
no message-length maximum server
dns-guard
protocol-enforcement
nat-rewrite
no id-randomization
no id-mismatch
no tsig enforced
policy-map type inspect esmtp _default_esmtp_map
description Default ESMTP policy-map
parameters
mask-banner
no mail-relay
no special-character
no allow-tls
match cmd line length gt 512
drop-connection log
match cmd RCPT count gt 100
drop-connection log
match body line length gt 998
log
match header line length gt 998
drop-connection log
match sender-address length gt 320
drop-connection log
match MIME filename length gt 255
drop-connection log
match ehlo-reply-parameter others
mask
policy-map type inspect ip-options _default_ip_options_map
description Default IP-OPTIONS policy-map
parameters
router-alert action allow
policy-map global_policy
class inspection_default
inspect dns migrated_dns_map_1
inspect ftp
inspect h323 h225 _default_h323_map
inspect h323 ras _default_h323_map
inspect rsh
inspect rtsp
inspect esmtp _default_esmtp_map
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options _default_ip_options_map
inspect icmp
inspect icmp error
inspect pptp
class class-default
policy-map type inspect sip _default_sip_map
description Default SIP policymap
parameters
im
no ip-address-privacy
traffic-non-sip
no rtp-conformance
policy-map type inspect dns _default_dns_map
description Default DNS policy-map
parameters
no message-length maximum client
no message-leI ran those commands while I had the nat off on the router and here are the results. note, i didn't make any changes to the ASA as you only said to remove the router RIP which I did and reloaded and no change.
As long as the statements ip nat outside on the Fastethernet 0/0 is off and the ip nat inside is off on the vlan and the overload statement is taken out, I cannot hit the internet.
CISCO-2811#conf t
Enter configuration commands, one per line. End with CNTL/Z.
CISCO-2811(config)#int
CISCO-2811(config)#interface f
CISCO-2811(config)#interface fastEthernet 0/1.3
CISCO-2811(config-subif)#no ip nat inside
CISCO-2811(config-subif)#exit
CISCO-2811(config)#inter
CISCO-2811(config)#interface f
CISCO-2811(config)#interface fastEthernet 0/0
CISCO-2811(config-if)#no ip nat outside
CISCO-2811(config-if)#exit
CISCO-2811(config)#$nside source list 1 interface FastEthernet0/0 overload
Dynamic mapping in use, do you want to delete all entries? [no]: y
CISCO-2811(config)#exit
CISCO-2811#sh ip arp
Protocol Address Age (min) Hardware Addr Type Interface
Internet 10.10.1.1 202 c47d.4f3b.8ea6 ARPA FastEthernet0/0
Internet 10.10.1.2 - 0019.55a7.2ae8 ARPA FastEthernet0/0
Internet 172.16.10.1 - 0019.55a7.2ae9 ARPA FastEthernet0/1.1
Internet 172.16.10.3 238 0011.5c73.28c1 ARPA FastEthernet0/1.1
Internet 172.16.10.50 72 cc2d.8c78.065a ARPA FastEthernet0/1.1
Internet 172.16.20.1 - 0019.55a7.2ae9 ARPA FastEthernet0/1.2
Internet 172.16.20.3 196 0011.5c73.28c2 ARPA FastEthernet0/1.2
Internet 192.168.1.1 - 0019.55a7.2ae9 ARPA FastEthernet0/1.3
Internet 192.168.1.2 0 0024.e864.01a8 ARPA FastEthernet0/1.3
Internet 192.168.1.3 155 0011.5c73.28c0 ARPA FastEthernet0/1.3
Internet 192.168.1.5 61 4802.2a4c.1c74 ARPA FastEthernet0/1.3
Internet 192.168.1.20 0 5cf9.dd52.5fa9 ARPA FastEthernet0/1.3
Internet 192.168.1.50 0 308c.fb47.f2d9 ARPA FastEthernet0/1.3
Internet 192.168.1.51 1 ec35.8677.4057 ARPA FastEthernet0/1.3
Internet 192.168.1.52 1 b418.d136.ef72 ARPA FastEthernet0/1.3
Internet 192.168.1.53 1 8853.9572.e113 ARPA FastEthernet0/1.3
Internet 192.168.1.54 12 0009.b044.9f23 ARPA FastEthernet0/1.3
Internet 192.168.1.55 0 f47b.5e9a.7ae5 ARPA FastEthernet0/1.3
Internet 192.168.1.149 0 001e.4fc5.a199 ARPA FastEthernet0/1.3
Internet 192.168.1.174 0 b8ac.6fff.af83 ARPA FastEthernet0/1.3
CISCO-2811#sh ip route
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP
+ - replicated route, % - next hop override
Gateway of last resort is 10.10.1.1 to network 0.0.0.0
S* 0.0.0.0/0 [1/0] via 10.10.1.1
10.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C 10.10.1.0/30 is directly connected, FastEthernet0/0
L 10.10.1.2/32 is directly connected, FastEthernet0/0
172.16.0.0/16 is variably subnetted, 4 subnets, 2 masks
C 172.16.10.0/24 is directly connected, FastEthernet0/1.1
L 172.16.10.1/32 is directly connected, FastEthernet0/1.1
C 172.16.20.0/24 is directly connected, FastEthernet0/1.2
L 172.16.20.1/32 is directly connected, FastEthernet0/1.2
192.168.1.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.1.0/24 is directly connected, FastEthernet0/1.3
L 192.168.1.1/32 is directly connected, FastEthernet0/1.3
ASA
ASA5510# sh arp
Inside 10.10.1.2 0019.55a7.2ae8 12342
Outside 199.195.168.113 000c.4243.581a 2
Outside 199.195.168.116 e05f.b947.116b 2436
Outside 199.195.168.120 0017.c58a.1123 9192
DMZ 10.10.0.2 0025.849f.63e0 3192
VOIP 10.10.2.2 000d.bcdc.fc40 7754
ASA5510# sh route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is 199.195.168.113 to network 0.0.0.0
S 172.16.20.0 255.255.255.0 [1/0] via 10.10.1.2, Inside
S 172.16.10.0 255.255.255.0 [1/0] via 10.10.1.2, Inside
S 128.162.1.0 255.255.255.0 [1/0] via 10.10.0.2, DMZ
S 128.162.10.0 255.255.255.0 [1/0] via 10.10.0.2, DMZ
S 128.162.20.0 255.255.255.0 [1/0] via 10.10.0.2, DMZ
C 199.195.168.112 255.255.255.240 is directly connected, Outside
C 10.10.0.0 255.255.255.252 is directly connected, DMZ
C 10.10.1.0 255.255.255.252 is directly connected, Inside
S 192.168.1.0 255.255.255.0 [1/0] via 10.10.1.2, Inside
S* 0.0.0.0 0.0.0.0 [1/0] via 199.195.168.113, Outside
ASA5510# show xlate
35 in use, 784 most used
Flags: D - DNS, e - extended, I - identity, i - dynamic, r - portmap,
s - static, T - twice, N - net-to-net
TCP PAT from DMZ:10.10.0.2 22-22 to Outside:199.195.168.x 2222-2222
flags sr idle 481:54:14 timeout 0:00:00
TCP PAT from Inside:10.10.1.2 22-22 to Outside:199.195.168.x 222-222
flags sr idle 51:06:46 timeout 0:00:00
TCP PAT from VOIP:10.10.2.2 22-22 to Outside:199.195.168.x 2223-2223
flags sr idle 687:32:27 timeout 0:00:00
TCP PAT from Inside:192.168.1.2 3389-3389 to Outside:199.195.168.x 3389-3389
flags sr idle 457:17:01 timeout 0:00:00
TCP PAT from Inside:192.168.1.5 80-80 to Outside:199.195.168.x 8080-8080
flags sr idle 52:18:58 timeout 0:00:00
NAT from Outside:0.0.0.0/0 to any:0.0.0.0/0
flags sIT idle 353:10:21 timeout 0:00:00
UDP PAT from any:10.10.1.2/52581 to Outside:199.195.168.x/52581 flags ri idle 0:00:00 timeout 0:00:30
UDP PAT from any:10.10.1.2/55389 to Outside:199.195.168.x/55389 flags ri idle 0:00:03 timeout 0:00:30
UDP PAT from any:10.10.1.2/51936 to Outside:199.195.168.x/51936 flags ri idle 0:00:04 timeout 0:00:30
UDP PAT from any:10.10.1.2/51345 to Outside:199.195.168.x/51345 flags ri idle 0:00:09 timeout 0:00:30
UDP PAT from any:10.10.1.2/55985 to Outside:199.195.168.x/55985 flags ri idle 0:00:18 timeout 0:00:30
UDP PAT from any:10.10.1.2/49368 to Outside:199.195.168.x/49368 flags ri idle 0:00:22 timeout 0:00:30
UDP PAT from any:10.10.1.2/52441 to Outside:199.195.168.x/52441 flags ri idle 0:00:23 timeout 0:00:30
TCP PAT from any:10.10.1.2/57908 to Outside:199.195.168.x/57908 flags ri idle 0:08:37 timeout 0:00:30
TCP PAT from any:10.10.1.2/57907 to Outside:199.195.168.x/57907 flags ri idle 0:08:37 timeout 0:00:30
TCP PAT from any:10.10.1.2/57906 to Outside:199.195.168.x/57906 flags ri idle 0:08:37 timeout 0:00:30
TCP PAT from any:10.10.1.2/57896 to Outside:199.195.168.x/57896 flags ri idle 0:09:09 timeout 0:00:30
TCP PAT from any:10.10.1.2/57879 to Outside:199.195.168.x/57879 flags ri idle 0:10:23 timeout 0:00:30
TCP PAT from any:10.10.1.2/49441 to Outside:199.195.168.x/49441 flags ri idle 0:20:52 timeout 0:00:30
TCP PAT from any:10.10.1.2/57868 to Outside:199.195.168.x/57868 flags ri idle 0:25:28 timeout 0:00:30
TCP PAT from any:10.10.1.2/60519 to Outside:199.195.168.x/60519 flags ri idle 0:44:11 timeout 0:00:30
TCP PAT from any:10.10.1.2/60491 to Outside:199.195.168.x/60491 flags ri idle 0:44:20 timeout 0:00:30
TCP PAT from any:10.10.1.2/60484 to Outside:199.195.168.x/60484 flags ri idle 0:44:35 timeout 0:00:30
TCP PAT from any:10.10.1.2/60480 to Outside:199.195.168.x/60480 flags ri idle 0:44:51 timeout 0:00:30
TCP PAT from any:10.10.1.2/53851 to Outside:199.195.168.x/53851 flags ri idle 0:54:14 timeout 0:00:30
TCP PAT from any:10.10.1.2/57812 to Outside:199.195.168.x/57812 flags ri idle 0:58:30 timeout 0:00:30
TCP PAT from any:10.10.1.2/57810 to Outside:199.195.168.x/57810 flags ri idle 0:58:32 timeout 0:00:30
TCP PAT from any:10.10.1.2/53847 to Outside:199.195.168.x/53847 flags ri idle 1:00:18 timeout 0:00:30
TCP PAT from any:10.10.1.2/57808 to Outside:199.195.168.x/57808 flags ri idle 1:07:58 timeout 0:00:30
TCP PAT from any:10.10.1.2/60406 to Outside:199.195.168.x/60406 flags ri idle 1:42:13 timeout 0:00:30
TCP PAT from any:10.10.1.2/49259 to Outside:199.195.168.x/49259 flags ri idle 7:39:44 timeout 0:00:30
TCP PAT from any:10.10.1.2/49191 to Outside:199.195.168.x/49191 flags ri idle 7:42:39 timeout 0:00:30
TCP PAT from any:10.10.1.2/55951 to Outside:199.195.168.x/55951 flags ri idle 23:11:40 timeout 0:00:30
TCP PAT from any:10.10.1.2/55944 to Outside:199.195.168.x/55944 flags ri idle 23:15:19 timeout 0:00:30
TCP PAT from any:10.10.1.2/55942 to Outside:199.195.168.x/55942 flags ri idle 23:15:24 timeout 0:00:30
ASA5510# sh conn all
149 in use, 815 most used
TCP Outside 74.125.193.108:993 Inside 10.10.1.2:57879, idle 0:12:37, bytes 6398, flags UIO
TCP Outside 174.35.24.74:80 Inside 192.168.1.20:53879, idle 0:00:01, bytes 0, flags saA
TCP Outside 174.35.24.74:80 Inside 192.168.1.20:53878, idle 0:00:01, bytes 0, flags saA
TCP Outside 17.149.36.177:5223 Inside 10.10.1.2:60480, idle 0:16:53, bytes 4539, flags UIO
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53877, idle 0:00:02, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53876, idle 0:00:02, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53875, idle 0:00:05, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53874, idle 0:00:05, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53872, idle 0:00:11, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53871, idle 0:00:11, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53868, idle 0:00:08, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53867, idle 0:00:08, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53860, idle 0:00:17, bytes 0, flags saA
TCP Outside 98.22.121.19:443 Inside 192.168.1.20:53859, idle 0:00:17, bytes 0, flags saA
TCP Outside 17.172.233.95:5223 Inside 10.10.1.2:49191, idle 0:18:48, bytes 7384, flags UIO
TCP Outside 17.178.100.43:443 Inside 10.10.1.2:57810, idle 0:56:21, bytes 5797, flags UFIO
TCP Outside 23.206.216.93:80 Inside 10.10.1.2:53847, idle 0:54:15, bytes 2683, flags UFIO
TCP Outside 143.127.93.90:80 Inside 10.10.1.2:49259, idle 0:12:20, bytes 13315, flags UIO
TCP Outside 74.125.225.53:443 Inside 192.168.1.20:53864, idle 0:00:11, bytes 0, flags saA
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:49204, idle 0:00:04, bytes 67, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.174:50122, idle 0:00:07, bytes 43, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63275, idle 0:00:08, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63306, idle 0:00:18, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65059, idle 0:00:22, bytes 46, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64681, idle 0:00:30, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64661, idle 0:00:30, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.20:55618, idle 0:00:32, bytes 43, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65056, idle 0:00:33, bytes 48, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.55:59433, idle 0:00:41, bytes 33, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.20:52178, idle 0:00:42, bytes 33, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.174:61414, idle 0:00:43, bytes 34, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65438, idle 0:00:44, bytes 44, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63686, idle 0:00:44, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65416, idle 0:00:45, bytes 45, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.52:53047, idle 0:00:47, bytes 32, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.52:62213, idle 0:00:46, bytes 74, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.52:52347, idle 0:00:46, bytes 92, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.52:58069, idle 0:00:46, bytes 64, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.52:50753, idle 0:00:46, bytes 74, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65381, idle 0:00:50, bytes 50, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65082, idle 0:00:50, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64038, idle 0:00:50, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:49309, idle 0:00:51, bytes 43, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64034, idle 0:00:51, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:49197, idle 0:00:51, bytes 50, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64728, idle 0:00:51, bytes 49, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64309, idle 0:00:51, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63289, idle 0:00:51, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64174, idle 0:00:52, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.55:39286, idle 0:01:09, bytes 33, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63726, idle 0:01:09, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65482, idle 0:01:12, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65091, idle 0:01:13, bytes 61, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64976, idle 0:01:13, bytes 57, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63749, idle 0:00:51, bytes 103, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64043, idle 0:01:14, bytes 52, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64267, idle 0:01:24, bytes 45, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:64467, idle 0:01:26, bytes 45, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:65504, idle 0:01:26, bytes 46, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.55:38946, idle 0:01:35, bytes 33, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63701, idle 0:01:38, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63879, idle 0:01:46, bytes 45, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.174:58516, idle 0:01:49, bytes 51, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:63227, idle 0:01:51, bytes 62, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.174:65446, idle 0:01:53, bytes 43, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.2:49166, idle 0:01:55, bytes 54, flags -
UDP Outside 199.195.168.4:53 Inside 192.168.1.55:56680, idle 0:02:01, bytes 33, flags -
UDP Outside 192.55.83.30:53 Inside 192.168.1.2:65073, idle 0:00:44, bytes 50, flags -
TCP Outside 74.125.193.109:993 Inside 10.10.1.2:57808, idle 0:39:33, bytes 6392, flags UFIO
TCP Outside 74.125.225.54:443 Inside 192.168.1.20:53863, idle 0:00:13, bytes 0, flags saA
TCP Outside 143.127.93.89:80 Inside 10.10.1.2:60519, idle 0:46:30, bytes 346, flags UO
TCP Outside 74.125.225.32:443 Inside 192.168.1.20:53881, idle 0:00:01, bytes 0, flags saA
TCP Outside 74.125.225.32:443 Inside 192.168.1.20:53880, idle 0:00:01, bytes 0, flags saA
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:60627, idle 0:00:39, bytes 78, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:52088, idle 0:00:39, bytes 86, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:50533, idle 0:00:39, bytes 76, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:63347, idle 0:00:39, bytes 80, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:62213, idle 0:00:40, bytes 37, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:52347, idle 0:00:40, bytes 46, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:58069, idle 0:00:40, bytes 32, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.52:50753, idle 0:00:40, bytes 37, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.174:52254, idle 0:01:09, bytes 43, flags -
UDP Outside 205.171.3.65:53 Inside 192.168.1.174:50791, idle 0:01:25, bytes 35, flags -
TCP Outside 74.125.225.46:443 Inside 192.168.1.20:53870, idle 0:00:08, bytes 0, flags saA
TCP Outside 17.173.255.101:443 Inside 10.10.1.2:53851, idle 0:56:33, bytes 58, flags UfIO
TCP Outside 64.4.23.147:33033 Inside 10.10.1.2:55944, idle 0:44:45, bytes 558164, flags UFIO
TCP Outside 74.125.225.35:443 Inside 192.168.1.20:53869, idle 0:00:09, bytes 0, flags saA
UDP Outside 64.4.23.175:33033 Inside 192.168.1.174:26511, idle 0:01:17, bytes 28, flags -
UDP Outside 192.54.112.30:53 Inside 192.168.1.2:65380, idle 0:00:44, bytes 49, flags -
TCP Outside 74.125.142.108:993 Inside 10.10.1.2:57908, idle 0:10:47, bytes 7895, flags UIO
TCP Outside 74.125.142.108:993 Inside 10.10.1.2:57907, idle 0:10:49, bytes 20323, flags UIO
TCP Outside 74.125.142.108:993 Inside 10.10.1.2:57906, idle 0:10:47, bytes 6539, flags UIO
TCP Outside 74.125.142.108:993 Inside 10.10.1.2:57868, idle 0:27:44, bytes 6395, flags UIO
TCP Outside 91.190.218.59:443 Inside 10.10.1.2:55942, idle 0:41:39, bytes 2727, flags UFIO
TCP Outside 17.172.233.123:5223 Inside 10.10.1.2:49441, idle 0:23:10, bytes 4409, flags UIO
TCP Outside 74.125.225.41:443 Inside 192.168.1.20:53862, idle 0:00:16, bytes 0, flags saA
TCP Outside 74.125.225.41:443 Inside 192.168.1.20:53861, idle 0:00:16, bytes 0, flags saA
TCP Outside 143.127.93.115:80 Inside 10.10.1.2:60406, idle 0:42:59, bytes 970, flags UFIO
TCP Outside 143.127.93.118:80 Inside 10.10.1.2:60484, idle 0:46:54, bytes 328, flags UO
TCP Outside 17.172.233.98:5223 Inside 10.10.1.2:57896, idle 0:11:28, bytes 5081, flags UIO
UDP Outside 111.221.74.16:33033 Inside 192.168.1.174:26511, idle 0:01:18, bytes 31, flags -
TCP Outside 17.149.36.103:5223 Inside 192.168.1.174:60729, idle 0:00:04, bytes 0, flags saA
UDP Outside 192.5.6.30:53 Inside 192.168.1.2:65317, idle 0:00:44, bytes 51, flags -
UDP Outside 192.12.94.30:53 Inside 192.168.1.2:65356, idle 0:00:44, bytes 54, flags -
TCP Outside 17.149.36.180:5223 Inside 10.10.1.2:55951, idle 0:46:08, bytes 14059, flags UFIO
UDP Outside 111.221.74.28:33033 Inside 192.168.1.174:26511, idle 0:01:20, bytes 33, flags -
TCP Outside 63.235.20.160:80 Inside 192.168.1.20:53873, idle 0:00:08, bytes 0, flags saA
TCP Outside 50.19.127.112:443 Inside 192.168.1.50:60678, idle 0:00:00, bytes 0, flags saA
TCP Outside 65.55.122.234:80 Inside 192.168.1.174:60728, idle 0:00:14, bytes 0, flags saA
TCP Outside 65.55.122.234:80 Inside 192.168.1.174:60727, idle 0:00:15, bytes 0, flags saA
TCP Outside 65.55.122.234:80 Inside 192.168.1.174:60726, idle 0:00:15, bytes 0, flags saA
TCP Outside 65.55.122.234:443 Inside 192.168.1.174:2492, idle 0:00:16, bytes 0, flags saA
TCP Outside 65.55.122.234:2492 Inside 192.168.1.174:2492, idle 0:00:16, bytes 0, flags saA
UDP Outside 157.55.56.170:33033 Inside 192.168.1.174:26511, idle 0:01:21, bytes 37, flags -
TCP Outside 74.125.230.207:443 Inside 192.168.1.20:53866, idle 0:00:11, bytes 0, flags saA
TCP Outside 74.125.230.207:443 Inside 192.168.1.20:53865, idle 0:00:11, bytes 0, flags saA
UDP Outside 111.221.74.18:33033 Inside 192.168.1.174:26511, idle 0:01:17, bytes 29, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.20:55546, idle 0:00:06, bytes 46, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.20:60277, idle 0:00:06, bytes 46, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.20:55618, idle 0:00:34, bytes 43, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.52:60627, idle 0:00:36, bytes 78, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.52:52088, idle 0:00:36, bytes 86, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.52:50533, idle 0:00:36, bytes 76, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.52:63347, idle 0:00:36, bytes 80, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.20:56958, idle 0:01:24, bytes 34, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.20:51360, idle 0:01:26, bytes 34, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.174:50791, idle 0:01:27, bytes 35, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.20:54134, idle 0:01:46, bytes 34, flags -
UDP Outside 8.8.8.8:53 Inside 192.168.1.174:58516, idle 0:01:50, bytes 51, flags -
TCP Outside 23.207.7.46:80 Inside 192.168.1.55:59350, idle 0:00:02, bytes 0, flags saA
TCP Outside 23.207.7.46:80 Inside 192.168.1.55:59349, idle 0:00:16, bytes 0, flags saA
UDP Outside 205.171.2.65:53 Inside 192.168.1.174:50122, idle 0:00:09, bytes 43, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.55:48088, idle 0:00:42, bytes 33, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.52:62213, idle 0:00:45, bytes 74, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.52:52347, idle 0:00:45, bytes 92, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.52:58069, idle 0:00:45, bytes 64, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.52:50753, idle 0:00:45, bytes 74, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.174:61414, idle 0:00:47, bytes 34, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.55:54481, idle 0:01:08, bytes 33, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.174:52254, idle 0:01:09, bytes 43, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.55:40285, idle 0:01:34, bytes 33, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.174:65446, idle 0:01:55, bytes 43, flags -
UDP Outside 205.171.2.65:53 Inside 192.168.1.55:46155, idle 0:02:00, bytes 33, flags -
UDP Outside 66.104.81.70:5070 Inside 192.168.1.174:57609, idle 0:00:11, bytes 46, flags -
UDP Outside 64.4.23.156:33033 Inside 192.168.1.174:26511, idle 0:01:14, bytes 38, flags -
TCP Outside 65.54.167.15:12350 Inside 10.10.1.2:60491, idle 0:11:02, bytes 1405, flags UIO
TCP Outside 17.172.192.35:443 Inside 10.10.1.2:57812, idle 0:56:11, bytes 6116, flags UFIO
UDP Outside 157.55.56.176:33033 Inside 192.168.1.174:26511, idle 0:01:16, bytes 32, flags -
TCP Inside 192.168.1.20:53667 NP Identity Ifc 10.10.1.1:22, idle 0:00:00, bytes 37555, flags UOB
TCP Inside 10.10.1.2:53431 NP Identity Ifc 10.10.1.1:22, idle 0:09:03, bytes 20739, flags UOB
Ran on the ASA while overload statements were down on the router:
ASA5510# packet-tracer input Inside tcp 192.168.1.100 12345 8.8.8.8 80
Phase: 1
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 0.0.0.0 0.0.0.0 Outside
Phase: 2
Type: NAT
Subtype: per-session
Result: ALLOW
Config:
Additional Information:
Phase: 3
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 4
Type: NAT
Subtype: per-session
Result: ALLOW
Config:
Additional Information:
Phase: 5
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 6
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 1988699, packet dispatched to next module
Result:
input-interface: Inside
input-status: up
input-line-status: up
output-interface: Outside
output-status: up
output-line-status: up
Action: allow
Had to put these back in to get to the internet:
CISCO-2811#conf t
Enter configuration commands, one per line. End with CNTL/Z.
CISCO-2811(config)#inter
CISCO-2811(config)#interface f
CISCO-2811(config)#interface fastEthernet 0/0
CISCO-2811(config-if)#ip nat
CISCO-2811(config-if)#ip nat Outside
CISCO-2811(config-if)#exit
CISCO-2811(config)#in
CISCO-2811(config)#interface f
CISCO-2811(config)#interface fastEthernet 0/1.3
CISCO-2811(config-subif)#ip nat inside
CISCO-2811(config-subif)#exit
CISCO-2811(config)#$de source list 1 interface FastEthernet0/0 overload
CISCO-2811(config)#
Screenshot of ASDM: -
Access from Inside to Outside ASA 5510 ver 9.1
Hi All,
I need some help in getting an ASA up and processing traffic from the inside network to the internet. I have a Cisco 2811 Router behind a Cisco ASA 5510. From the ASA I can ping the 2811 and I can ping IP addresses on the internet. I have updated the IOS and ASDM on the router to the newest versions. 9.1(4) and 7.1. I believe the problem is in the Objects, ACL and getting those together, but I don't know much about the ASA and I don't know how the post 8.2 setup works. I am hoping I can get some help here to get me up and running so I can access the internet from behind the ASA.
Here is my ASA Config and I will post some of the 2811 Router config as well, though I am not sure thati s where the issue lies, but at this point, I haven't a clue. Both are up to date for the newest versions of the respective IOS.
I need to know what objects / ACL's et cetera to put in to get traffic flowing inside / out.
Thank you for the help!
ASA5510(config)# sh running-config
: Saved
ASA Version 9.1(4)
hostname ASA5510
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
names
dns-guard
interface Ethernet0/0
description LAN Interface
nameif Inside
security-level 100
ip address 10.10.1.1 255.255.255.252
interface Ethernet0/1
description WAN Interface
nameif Outside
security-level 0
ip address 199.195.168.100 255.255.255.240
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
management-only
shutdown
nameif management
security-level 0
no ip address
boot system disk0:/asa914-k8.bin
ftp mode passive
dns domain-lookup Outside
dns server-group DefaultDNS
name-server 199.195.168.4
name-server 205.171.2.65
name-server 205.171.3.65
domain-name internal.int
access-list USERS standard permit 10.10.1.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu Inside 1500
mtu Outside 1500
mtu management 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-715.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
router rip
network 10.0.0.0
network 199.195.168.0
version 2
no auto-summary
route Outside 0.0.0.0 0.0.0.0 199.195.168.113 1
route Inside 172.16.10.0 255.255.255.0 10.10.1.2 1
route Inside 172.16.20.0 255.255.255.0 10.10.1.2 1
route Inside 192.168.1.0 255.255.255.0 10.10.1.2 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
http server enable
http 0.0.0.0 0.0.0.0 Inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association pmtu-aging infinite
crypto ca trustpool policy
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 Inside
ssh timeout 60
ssh version 2
ssh key-exchange group dh-group1-sha1
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
username redacted password vj4PdtfGNFrB.Ksz encrypted privilege 15
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns migrated_dns_map_1
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns migrated_dns_map_1
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
: end
CISCO 2811:
Current configuration : 2601 bytes
! Last configuration change at 07:24:32 UTC Fri Jan 3 2014
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
hostname RouterDeMitch
boot-start-marker
boot system flash
boot-end-marker
! card type command needed for slot/vwic-slot 0/0
no aaa new-model
dot11 syslog
ip source-route
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.1.1 192.168.1.49
ip dhcp excluded-address 172.16.10.1 172.16.10.49
ip dhcp excluded-address 172.16.20.1 172.16.20.49
ip dhcp pool Mitchs_Network
network 192.168.1.0 255.255.255.0
dns-server 199.195.168.4 205.171.2.65 205.171.3.65 8.8.8.8
default-router 192.168.1.1
ip dhcp pool VLAN10
network 172.16.10.0 255.255.255.0
default-router 172.16.10.1
dns-server 199.195.168.4 205.171.2.65 205.171.3.65 8.8.8.8
ip dhcp pool VLAN20
network 172.16.20.0 255.255.255.0
dns-server 199.195.168.4 205.171.2.65 205.171.3.65 8.8.8.8
default-router 172.16.20.1
no ip domain lookup
ip name-server 199.195.168.4
ip name-server 205.171.2.65
ip name-server 205.171.3.65
ip name-server 8.8.8.8
multilink bundle-name authenticated
crypto pki token default removal timeout 0
redundancy
interface FastEthernet0/0
description CONNECTION TO INSIDE INT. OF ASA
ip address 10.10.1.2 255.255.255.252
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
interface FastEthernet0/1
no ip address
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
interface FastEthernet0/1.1
encapsulation dot1Q 10
ip address 172.16.10.1 255.255.255.0
interface FastEthernet0/1.2
encapsulation dot1Q 20
ip address 172.16.20.1 255.255.255.0
interface FastEthernet0/1.3
description Trunk Interface VLAN 1
encapsulation dot1Q 1 native
ip address 192.168.1.1 255.255.255.0
interface Dialer0
no ip address
router rip
version 2
network 172.16.0.0
network 192.168.1.0
network 199.195.168.0
no auto-summary
ip default-gateway 10.10.1.1
ip forward-protocol nd
no ip http server
no ip http secure-server
ip dns server
ip nat inside source list 1 interface FastEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 FastEthernet0/0
access-list 1 permit any
dialer-list 1 protocol ip permit
control-plane
line con 0
exec-timeout 0 0
password encrypted
login
line aux 0
line vty 0 4
exec-timeout 0 0
transport input all
scheduler allocate 20000 1000
endI made those changes, but still no internet. I did not add this statement nat (inside,outside) after-auto source dynamic any interface I went with the more granular.
ASA5510# sh running-config
: Saved
ASA Version 9.1(4)
hostname ASA5510
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
passwd liqhNWIOSfzvir2g encrypted
names
dns-guard
interface Ethernet0/0
description LAN Interface
nameif Inside
security-level 100
ip address 10.10.1.1 255.255.255.252
interface Ethernet0/1
description WAN Interface
nameif Outside
security-level 0
ip address 199.195.168.123 255.255.255.240
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
management-only
shutdown
nameif management
security-level 0
no ip address
boot system disk0:/asa914-k8.bin
ftp mode passive
dns domain-lookup Outside
dns server-group DefaultDNS
name-server 199.195.168.4
name-server 205.171.2.65
name-server 205.171.3.65
domain-name internal.int
object-group network PAT-SOURCE
network-object 172.16.10.0 255.255.255.0
network-object 172.16.20.0 255.255.255.0
network-object 192.168.1.0 255.255.255.0
network-object 10.10.1.0 255.255.255.252
access-list USERS standard permit 10.10.1.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu Inside 1500
mtu Outside 1500
mtu management 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-715.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (Inside,Outside) after-auto source dynamic PAT-SOURCE interface
router rip
network 10.0.0.0
network 199.195.168.0
version 2
no auto-summary
route Outside 0.0.0.0 0.0.0.0 199.195.168.113 1
route Inside 172.16.10.0 255.255.255.0 10.10.1.2 1
route Inside 172.16.20.0 255.255.255.0 10.10.1.2 1
route Inside 192.168.1.0 255.255.255.0 10.10.1.2 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
http server enable
http 0.0.0.0 0.0.0.0 Inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association pmtu-aging infinite
crypto ca trustpool policy
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 Inside
ssh timeout 60
ssh version 2
ssh key-exchange group dh-group1-sha1
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns migrated_dns_map_1
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns migrated_dns_map_1
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
: end
Message was edited by: Mitchell Tuckness -
Cisco ASA 5510 Site to Site VPN with Sonicwall
I am trying to setup a VPN tunnel between a Cisco ASA 5510 (Version 8.2(2)) and Sonicwall TZ200. I got tunnel up and going and I am able to ping the Cisco ASA internal IP from the Sonicwall LAN but nothing else works. When I try to ping a host behind the Cisco ASA from the Sonicwall LAN I get the following message "Asymmetric NAT rules matched for forward and reverse flows; Connection for tcp src outside:10.20.10.x/xxxx dst inside:10.20.2.x/xxxx denied due to NAT reverse path failures" on the ASA
Googling the above error shows issues with version 8.3 and later which looked like the nat commands were changed but the ASA I am working on is still on 8.2 and the other common issue is not adding a NAT exemption. I have double-triple checked that I did add a NAT exception rule from the hosts on the cisco network to the hosts on the Sonicwall network. Seems like I have hit a road block so any help would be appreciated. Thanks
Here are some excertps from the config file (10.20.2.0 behind the cisco and 10.20.10.0 behind the sonicwall)
nat (inside) 0 access-list nonat
access-list nonat extended permit ip 10.20.2.0 255.255.255.0 10.20.10.0 255.255.255.0
access-list outside_1_cryptomap extended permit ip 10.20.2.0 255.255.255.0 10.20.10.0 255.255.255.0
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set peer x.x.x.x
crypto map outside_map 1 set transform-set ESP-3DES-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 5
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 28800
group-policy SiteToSitePolicy internal
group-policy SiteToSitePolicy attributes
vpn-idle-timeout none
vpn-tunnel-protocol IPSec
split-tunnel-network-list none
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group x.x.x.x general-attributes
default-group-policy SiteToSitePolicy
tunnel-group x.x.x.x ipsec-attributes
pre-shared-key *****
Added few excerpts from config fileYes inspect icmp is enabled in global_policy
The ping requests time out (The only ping that works is when I ping from the remote side to the ASA internal IP address, no other pings from either side work)
#show crypto isakmp sa
1 IKE Peer: x.x.x.x
Type : L2L Role : responder
Rekey : no State : MM_ACTIVE
#show crypto ipsec sa
interface: outside
Crypto map tag: outside_map, seq num: 1, local addr: x.x.x.x
access-list outside_2_cryptomap extended permit ip 10.20.2.0 255.255.255.0 10.20.10.0 255.255.255.0
local ident (addr/mask/prot/port): (10.20.2.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (10.20.10.0/255.255.255.0/0/0)
current_peer: y.y.y.y
#pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
#pkts decaps: 39543, #pkts decrypt: 39543, #pkts verify: 39543
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
#pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
#PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
#send errors: 0, #recv errors: 0
local crypto endpt.: x.x.x.x, remote crypto endpt.: y.y.y.y
path mtu 1500, ipsec overhead 58, media mtu 1500
current outbound spi: 0ED0F897
current inbound spi : 596CCE6F
inbound esp sas:
spi: 0x596CCE6F (1500302959)
transform: esp-3des esp-sha-hmac no compression
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 50327552, crypto-map: outside_map
sa timing: remaining key lifetime (sec): 7440
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0xFFFFFFFF 0xFFFFFFFF
outbound esp sas:
spi: 0x0ED0F897 (248576151)
transform: esp-3des esp-sha-hmac no compression
in use settings ={L2L, Tunnel, PFS Group 2, }
slot: 0, conn_id: 50327552, crypto-map: outside_map
sa timing: remaining key lifetime (sec): 7440
IV size: 8 bytes
replay detection support: Y
Anti replay bitmap:
0x00000000 0x00000001 -
ASA 5510 and VPN access to remote site over Ext WAN
ASA 5510
int client IP 172.0.1.XXX /24
VPN Client IP 172.0.1.248 /29
Static routes in the ASA
1) 0.0.0.0 --- points to router1
2) 172.29.1.1 --- Points to router2
3) 172.29.1.2 --- Points to router2
Router1 Internet connection // VPN access in path
Router2 Dedicated line to offsite hosting // Dedicated routes in ASA
................../---- ROUTER 1
..Inside -- ASA --- outside (switch 2 rtrs)
..................\---- ROUTER 2
If a PC from inside the network wants to talk with 172.29.1.2 it will work fine. If I VPN into the router, I can connect to anything onsite. I cannot talk to 172.29.1.1 or .2
At first I thought it was the same-security-traffic issue and applied same-security-traffic permit inter-interface then i tried same-security-traffic permit intra-interface.
Both commands failed, Looking at the diagram I think its something with the fact I VPN into this ASA. Now router2 see's our ASA as its external. So it see's our 208.12.*.* as the outgouing address and dest is 172.29.1.1 or .2
I did a capture on the outside interface and I see the following. Now these caps are from the inside PC's accessing the website.
3000 packets captured
1: 15:03:38.176733 208.12.*.*.60404 > 172.29.1.2.443: P 2697372408:2697372444(36) ack 2813073572 win 64360
2: 15:03:38.179815 208.12.*.*.63637 > 172.29.1.2.443: P 3373326671:3373326705(34) ack 3255654279 win 64512
3: 15:03:38.179876 208.12.*.*.60404 > 172.29.1.2.443: P 2697372444:2697372480(36) ack 2813073572 win 64360
4: 15:03:38.180181 172.29.1.2.443 > 208.12.*.*.27133: . ack 838693750 win 65456
5: 15:03:38.180212 172.29.1.2.443 > 208.12.*.*.26920: P 1652457319:1652457373(54) ack 2226176804 win 65482
Can someone point me in the right direction on how I would get the VPN working so it too can connect to those websites?Hi,
Did you try to do NONAT for the traffic from 172.0.1.0 going to 172.29.1.0
Something like this:-
access-list NONAT permit ip 172.0.1.0 255.255.255.0 172.29.1.0 255.255.255.0
nat (Inside) 0 access-list NONAT -
ASA 5510 Not able to route traffic between 2 LAN interfaces
Hi everybody,
I need help to enable traffic between two physical ports on my Cisco ASA 5510. I created access rules and NAT but traffic doe not go from accounting interface to Inside. I am able to access internet from both interfaces. Can someone pin point me in the right direction since I am not an expert in Cisco but has to finish this by the end of the week.
Thank you,
Sigor
Here is my configuration:
ASA Version 8.2(2)
hostname Cisco
domain-name xxx.com
names
interface Ethernet0/0
description Outside
nameif Outside
security-level 0
ip address 101.101.101.101 255.255.240.0
interface Ethernet0/1
description Inside Network
nameif Inside
security-level 90
ip address 192.168.10.1 255.255.255.0
interface Ethernet0/2
description Accounting
nameif Accounting
security-level 100
ip address 20.0.1.1 255.255.255.0
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
management-only
ftp mode passive
clock timezone EST -5
dns domain-lookup Outside
dns server-group DefaultDNS
name-server 8.8.8.8
domain-name xxx.com
same-security-traffic permit inter-interface
object-group service Port-10000 tcp
port-object eq 10000
object-group service Port-8080 tcp
port-object eq 8080
object-group service Port-8011 tcp
port-object eq 8011
object-group service DM_INLINE_TCP_1 tcp
group-object Port-8080
port-object eq www
group-object Port-8011
object-group service DM_INLINE_TCP_2 tcp
group-object Port-10000
port-object eq https
port-object eq www
object-group service rdp tcp
port-object eq 3389
object-group service DM_INLINE_TCP_3 tcp
group-object rdp
port-object eq ftp
object-group service DM_INLINE_TCP_4 tcp
group-object Port-10000
port-object eq www
port-object eq https
port-object eq ssh
object-group service DM_INLINE_TCP_5 tcp
group-object Port-8011
group-object Port-8080
port-object eq www
object-group service DM_INLINE_TCP_6 tcp
group-object Port-10000
port-object eq www
port-object eq https
object-group service DM_INLINE_TCP_7 tcp
group-object rdp
port-object eq ftp
access-list Outside_access_in extended permit tcp any host 101.101.101.104 object-group DM_INLINE_TCP_5
access-list Outside_access_in extended permit tcp any host 101.101.101.102 object-group DM_INLINE_TCP_6
access-list Outside_access_in extended permit tcp any host 101.101.101.103 object-group DM_INLINE_TCP_7
access-list Outside_access_in extended permit tcp any host 101.101.101.106 eq smtp
access-list Outside_1_cryptomap extended permit ip 192.168.10.0 255.255.255.0 192.168.50.0 255.255.255.0
access-list Inside_nat0_outbound extended permit ip 192.168.10.0 255.255.255.0 192.168.50.0 255.255.255.0
access-list Inside_nat0_outbound extended permit ip 192.168.10.0 255.255.255.0 192.168.80.0 255.255.255.0
access-list CiscoIPsec_splitTunnelAcl standard permit 192.168.10.0 255.255.255.0
access-list Accounting extended permit ip 20.0.1.0 255.255.255.0 192.168.10.0 255.255.255.0
access-list Accounting extended permit ip 20.0.1.0 255.255.255.0 any
pager lines 24
logging asdm informational
mtu Outside 1500
mtu Inside 1500
mtu Accounting 1500
mtu management 1500
ip local pool IPSecDHCP 192.168.80.100-192.168.80.200 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (Outside) 1 interface
nat (Inside) 0 access-list Inside_nat0_outbound
nat (Inside) 1 0.0.0.0 0.0.0.0
nat (Accounting) 1 0.0.0.0 0.0.0.0
static (Inside,Outside) tcp 101.101.101.104 www 192.168.10.14 www netmask 255.255.255.255
static (Inside,Outside) tcp 101.101.101.104 8011 192.168.10.14 8011 netmask 255.255.255.255
static (Inside,Outside) tcp 101.101.101.104 8080 192.168.10.14 8080 netmask 255.255.255.255
static (Inside,Outside) tcp 101.101.101.102 10000 192.168.10.3 10000 netmask 255.255.255.255
static (Inside,Outside) tcp 101.101.101.102 https 192.168.10.3 https netmask 255.255.255.255
static (Inside,Outside) tcp 101.101.101.102 www 192.168.10.3 www netmask 255.255.255.255
static (Inside,Outside) tcp 101.101.101.103 ftp 192.168.10.17 ftp netmask 255.255.255.255
static (Inside,Outside) tcp 101.101.101.103 3389 192.168.10.32 3389 netmask 255.255.255.255
static (Inside,Outside) tcp 101.101.101.106 smtp 192.168.10.23 smtp netmask 255.255.255.255
static (Inside,Accounting) 192.168.10.0 192.168.10.0 netmask 255.255.255.0
access-group Outside_access_in in interface Outside
access-group Accounting in interface Accounting
route Outside 0.0.0.0 0.0.0.0 101.101.101.101 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
http 192.168.10.0 255.255.255.0 Inside
http 20.0.1.0 255.255.255.0 Accounting
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 32608000
crypto ipsec security-association replay disable
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256
-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set security-association lifetime kilobytes 4608000
crypto map Outside_map 1 match address Outside_1_cryptomap
crypto map Outside_map 1 set pfs group1
crypto map Outside_map 1 set peer 89.216.17.35
crypto map Outside_map 1 set transform-set ESP-3DES-SHA
crypto map Outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map Outside_map interface Outside
crypto isakmp enable Outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 192.168.10.0 255.255.255.0 Inside
ssh timeout 5
console timeout 0
dhcpd address 20.0.1.100-20.0.1.200 Accounting
dhcpd dns 192.168.10.19 8.8.8.8 interface Accounting
dhcpd lease 306800 interface Accounting
dhcpd domain abtscs.com interface Accounting
dhcpd enable Accounting
dhcpd address 192.168.1.2-192.168.1.254 management
dhcpd enable management
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy CiscoIPsec internal
group-policy CiscoIPsec attributes
dns-server value 192.168.10.30 192.168.10.19
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value CiscoIPsec_splitTunnelAcl
default-domain value xxx.com
vpn-group-policy CiscoIPsec
tunnel-group 198.226.20.35 type ipsec-l2l
tunnel-group 198.226.20.35 ipsec-attributes
pre-shared-key *****
tunnel-group CiscoIPsec type remote-access
tunnel-group CiscoIPsec general-attributes
address-pool IPSecDHCP
default-group-policy CiscoIPsec
tunnel-group CiscoIPsec ipsec-attributes
pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
Cryptochecksum:2a7c97a7a22397908ef83ca6f0065919
: endWithout diving too deep into your config, I noticed a couple of things:
interface Ethernet0/1
description Inside Network
nameif Inside
security-level 90
ip address 192.168.10.1 255.255.255.0
interface Ethernet0/2
description Accounting
nameif Accounting
security-level 100
ip address 20.0.1.1 255.255.255.0
On an ASA, higher security level interfaces are always allowed, by default, to lower security levels, but not the other way around. So, if you want to keep this config, you would need an acl on the Inside interface to allow traffic to go from level 90 to 100:
access-list Inside permit ip any any
access-group Inside in interface Inside
The acl will permit the traffic into either interface (outside or Accounting). As long as you have your other rules set up correctly, this should resolve your issue...
HTH,
John -
ASA 5510 ignoring configured acl entry?
Greetings,
I'm configuring up aa ASA-5510, and I have several interfaces, some of which include:
interface Ethernet0/0.200
vlan 200
nameif SITECORP
security-level 90
ip address 10.1.4.1 255.255.254.0
interface Ethernet0/0.207
vlan 207
nameif SITESERVER
security-level 90
ip address 10.1.7.1 255.255.255.128
interface Ethernet0/1.311
vlan 311
nameif MOD1BMS
security-level 100
ip address 10.1.144.1 255.255.252.0
I have the following access-lists configured and applied:
access-list SITECORP_access_in extended permit ip any any
access-list SITESERVER_access_out extended permit tcp object-group SITECORP object-group SITESERVER eq www
access-list MOD1BMS_out extended permit tcp object-group SITECORP object-group MOD1BMS eq www
fw# show run object-group
object-group network SITECORP
network-object 10.1.4.0 255.255.254.0
object-group network MOD1BMS
network-object 10.1.144.0 255.255.252.0
object-group network SITESERVER
network-object 10.1.7.0 255.255.255.128
fw# show run nat-control
no nat-control
packet-tracer shows traffic from SITECORP to MOD1BMS (a higher security-level) on tcp/80 is successful, whereas it shows the same traffic from SITECORP to SITESERVER is denied, due to implicit rule.
fw# packet-tracer input SITECORP tcp 10.1.4.11 1234 10.1.144.200 80 detailed
<snip>
Phase: 3
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group SITECORP_access_in in interface SITECORP
access-list SITECORP_access_in extended permit ip any any
Additional Information:
Forward Flow based lookup yields rule:
in id=0xd5641ec8, priority=12, domain=permit, deny=false
hits=1860, user_data=0xd5526cb0, cs_id=0x0, flags=0x0, protocol=0
src ip=0.0.0.0, mask=0.0.0.0, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0
fw# packet-tracer input SITECORP tcp 10.1.4.11 1234 10.1.7.11 80 detailed
<snip>
Phase: 3
Type: ACCESS-LIST
Subtype:
Result: DROP
Config:
Implicit Rule
Additional Information:
Forward Flow based lookup yields rule:
in id=0xd544e8c8, priority=110, domain=permit, deny=true
hits=8, user_data=0x0, cs_id=0x0, flags=0x3000, protocol=0
src ip=0.0.0.0, mask=0.0.0.0, port=0
dst ip=0.0.0.0, mask=0.0.0.0, port=0
This definitely confuses me, because SITECORP has an inbound access-list of permit ip any any.
Can anyone suggest what I'm missing, how to go about making this work, or what more I might provide to troubleshoot?
Regards,
PhilHello Phil,
That is correct no matter what ACE (access-list entries) you have configured on one interface, if that interface wants to talk to another one with the same security level, the connection would not be allowed (Asa/Pix speaking)
But you do not have to change the Security level, of course that is one work-around but again the solution is :
- same-security-traffic permit inter-interface
Please mark the question as answered for future queries regarding the same issue unless you have any other question, I would be more than glad to help.
Regards,
Julio
Maybe you are looking for
-
i tried to buy points for a game with my funds but every time i try to buy them the ipad always sends me to th credit card info!!
-
Automatic approval workflow does not work anymore
Hi, Our automatic approval workflows configured via standard business configuration sets (process controlled) do not work anymore. They did work previously. After changing the BUS objects 'automatic approval' workflow into the 1-step manager approval
-
ParticalTrigger grammar mistake
[2009-12-04T17:38:47.601+08:00] [AdminServer] [WARNING] [] [org.apache.myfaces.trinidadinternal.context.RequestContextImpl] [tid: [ACTIVE].ExecuteThread: '5' for queue: 'weblogic.kernel.Default (self-tuning)'] [userId: anonymous] [ecid: 0000ILP3^t32j
-
Moving the Hard Drive to a new Macbook Pro
I am going to be switching from a MId 2012 13.3"/2.5GhZ Core i5 to a Mid 2012 13.3"/2.9GhZ, Core i7. Can I just swap out the Hard Drives, assuming both Macbooks are on the latest version of Mountain Lion? Thank you
-
Hello This might sound like a daft question, but can anyone tell me where I can find the Collections Panel in Bridge CS4? I can see Keywords and Filter, and I understand that Collections is supposed to be next to Filter. But I cant see it or locate i