Native Projector resolution

I creating a video which I will be show tomorrow. I researched the projector and see its native resolution is 1024 X 768 and with Premiere Elements 12 I don't have that as a save option, any suggestions for a complete newbie?

Ruidoso Bill
I do not work with projectors but, from what I have read, I believe that I have introduced relevant focus points for you to consider. You might want to take a look at the video in the following link where the presenter shows a result when using 16:9 video with the 4:3 type of protector that you have.
http://www.projectorpeople.com/resources/aspect-ratios.asp
The link is presented for informational and non promotional purposes.
When you wrote
I shot the video with a Nikon D800, HD 1080i 29.97 Fps editing mode, Frame size is 1920 X 1080. When I save the project for use as playback on this computer it displays the frame size as 720 X 480.
is it possible that your export settings were not correct? You may have missed an opportunity to customize the export settings to 1920 x 1080 and got caught up in a SD setting? If the projector was not implicated in your result that I quoted, it may just be a matter of adjusting the export settings rather than a major problem with the scaling done by this projector when 1920 x 1080 16:9 video was involved.
Are you sure about the 1080i? Could it have been 1080p. From what I have read of your Nikon D800 it would appear that it uses just progressive frame rates.
If you have 1080p, then a good export choice would be Publish+Share/Computer/AVCHD/with Presets = MP4 H.264 1920 x 1080p30 or Publish+Share/Computer/AVCHD/with Presets = Vimeo HD.
We will be watching for further developments.
Thanks.
ATR

Similar Messages

  • Airplay screen mirroring on 4:3 projector, resolution problems.

    Hi!
    I have an iPad 3, an ATV3 and a NEC NP400 projector which I'm trying to get to work together. I'm not sure about the projectors resolution, but i know it has a 4:3 aspect ratio.
    I've tried to use screen mirroring with both the ATV 3 and a VGA adapter, and the problem is that I get black bars on each side no matter which method I use. I understand that the iPad 3 has a 4:3 aspect ratio and that black bars would appear with a 16:9 screen, but not on a 4:3 screen which is the ipads native aspect ratio.
    It feels as if the iPad by defalut assumes that I'm having a 16:9 projector and adjust the aspect ratio to that fact. Is there anyway to tell the iPad that i'm having a 4:3 projector? Or should it detect that automatically?
    The ATV fills the whole screen without black bars on each side, but as soon as I'm turning screen mirroring on via airplay the aspect ratio changes. There is no difference if I'm using the ATV or the VGA adapter.
    How does these things work, and is there a solution?`
    Thanks!

    Hi!
    I have an iPad 3, an ATV3 and a NEC NP400 projector which I'm trying to get to work together. I'm not sure about the projectors resolution, but i know it has a 4:3 aspect ratio.
    I've tried to use screen mirroring with both the ATV 3 and a VGA adapter, and the problem is that I get black bars on each side no matter which method I use. I understand that the iPad 3 has a 4:3 aspect ratio and that black bars would appear with a 16:9 screen, but not on a 4:3 screen which is the ipads native aspect ratio.
    It feels as if the iPad by defalut assumes that I'm having a 16:9 projector and adjust the aspect ratio to that fact. Is there anyway to tell the iPad that i'm having a 4:3 projector? Or should it detect that automatically?
    The ATV fills the whole screen without black bars on each side, but as soon as I'm turning screen mirroring on via airplay the aspect ratio changes. There is no difference if I'm using the ATV or the VGA adapter.
    How does these things work, and is there a solution?`
    Thanks!

  • Projectors (resolution) and Apple TV

    I need some help in clarifying two things here. 
    1. What projector resolutions are going to work with apple TV (the new little black box)?  I have a projector that is XGA (1024 X 768).  Can it support apple TV?  I am also looking at other projectors... WXGA (1200 X 800) and HD projectors (1920 X 1080) (1080p).  Can a WXGA projector support apple TV?  I imagine the HD projectors can.
    2. If my XGA progector can support apple TV, has anyone found a device that works with converting HDMI to VGA?  http://www.monoprice.com/products/product.asp?c_id=101&cp_id=10114&cs_id=1011410 &p_id=8126&seq=1&format=2&res=1  Has anyone tried this device and has it worked?
    Thanks a bunch!
    Cheers,
    Josh

    Ok, I have checked the specs on my Toshiba TDP-T9U projector.  http://www.projectorcentral.com/Toshiba-TDP-T9U.htm says, "
    Compatibility:
    HDTV:
    720p,  1080i,  576i
      576p
    EDTV/480p:
    Yes
    SDTV/480i:
    Yes
    Component Video:
    Yes
    Video:
    Yes
    Digital Input:
    No
    Computers:
    Yes
    and the converter at http://www.monoprice.com/products/product.asp?c_id=101&cp_id=10114&cs_id=1011410 &p_id=8126&seq=1&format=2&res=1 says, "The converter supports HDCP 1.2, so handshaking and copy protection will not be an issue. The 10-bit DAC (digital-to-analog converter) can convert signals up to 1080p with 165 MHz/1.65 Gbps per channel bandwidth. "
    So, I am assuming those 2 issues are taken care of, right?!  Perhaps I'll buy the converter when it comes off back order and I'll repost indicating if it works or not.  I'm sure there are many people in the same boat as me.
    Thank you for clarifying those 2 issues.

  • Unsatisfactory 15" MacBook Pro Native Screen Resolution

    I recently purchased the latest 15" MacBook Pro and am disappointed with the native screen resolution (1280 by 800), in which the fonts are JUST a little too small.
    On the Apple site, it lists 1440 by 900 as the native resolution for this model, but I have yet to see that option listed under System Preferences. There only "Native Screen Resolution" (just small enough to drive a person crazy), or "1440x800", so on and so forth.
    What am I missing here? Has anyone else seen this on their models?

    For the MBP, the highest resolution on your machine is the one you want. In your case, it's 1680 x 1050. Don't worry about "native"; in some cases, the setting is wrong, and it should in no way affect your computing.
    I had a feeling that this was just the way the machine was built. I'm aware that it has no effect on the computing. I just wanted to bring up this issue because it's disingenuous from Apple's side and frustrating to a customer to list the aspect ratio specs on the site and not have the machine actually reflect that. Whatever is listed on the site should be what a person buys.
    I am assuming that there is no fix or software update that would help correct this issue. However, i do want to make the comment that while this machine is great, I personally feel that it would be nice for future models to have the system fonts in the highest resolution to be just slightly larger. The current resolution for this MBP is set where it is just small enough to be hard to read. My two cents.
    Thanks for your help.

  • SXGA+ Projector resolution not supported ?

    I have a projection design f30 projector that has a maximum native display of 1400 x 1050 SXGA+
    From a PC it will display this resolution no problem however with a macpro or any laptop i've tried the most I can get is 1280 x 720 ?
    Is their anything I can do to rectify this ?
    Many thanks
    Matt

    Dual Link DVI is used to support displays that are very wide, such as the Apple Cinema display. These displays divide the LCD into left and right zones, (as if it were made of two LCD units side-by-side). The control signals are used for both sides, but the data are provided for the left and right panes separately, on two sets of pins in the cable.
    A dual link DVI cable/port must have all pins populated. A single-link DVI port/cable often has three columns of pins near the center missing.
    You can only Mirror resolutions that also work for your built-in display. If your built-in display cannot do this resolution, then the setting will not be available for the external display.
    When you switch to "Extended Desktop", many more resolutions will become available for the external, because the built-in and the external can each operate independently. Each display in "Extended Desktop" will be looking at a portion of a very large Virtual Desktop, (i.e., they will not hold exactly the same picture.) You can then use the arrange button that appears to position the two displays into the Up/Down Left/Right orientation you prefer.
    The windows you wish to display can be moved to display completely on one display or the other, or overlapping both displays. This feature works for all well-behaved Mac Applications.

  • Projector resolution?

    I am hooking up an Epson Home Cinema digital projector to an iMac G5. When the projector is not connected, the highest I can set the screen resolution is 1440 X 900. But when I connect the projector, then I have the option of 1920 X 1080 (which is the native resolution of the projector). However, the screen on the Mac looks the same whether it is set to 1440 X 900 or 1920 X 1080. I am confused about the resolutions. Is the projector only showing what the screen is showing? And what is the screen showing--1440 X 900 or 1920 X1080? Or can the projector show 1920 X 1080 while the screen is showing 1440 X 900? Any help to clarify resolution and projectors would be much appreciated.
    --Nancy

    The 17" iMac G5s if I remember correctly maxed at 1440 x 900 for their screen.  The higher resolution I believe is just for the projector.  Once you determine the size of your screen measured diagonally, you can tell what the max on screen resolution is, or try to change resolutions with Apple menu -> System Preferneces -> Displays with the projector not attached.  Thaat would resolve that mystery once and for all.

  • Cannot get native 1440x900 resolution

    Hey guys. I just upgraded to snow leopard and after using it for a few days, the resolution on my external monitor got warped suddenly and now I can't change the resolution back to the native 1440x900 60Hz. Although there are other resolutions available, it doesn't look clear on the monitor. I would appreciate any answers given. Thanks. (By the way, it's connect by mini-dvi to VGA)
    Early 2008 White Macbook 2.4Ghz

    i don't have a direct answer, but you could just fiddle around with different settings on both the monitor and the computer. sometimes, you'll end up with different settings for each depending on the output of the picture. sometimes at school, i'll connect to an LCD projector and i get a really bad resolution on the computer, but its fine on the screen. you just have to try different things to get the best result. it shouldn't be an issue of the OS.
    hope that helps!
    -MacDarling55

  • Cant Achieve Native Monitor Resolution

    I have an HP Elite H8-1240t with Intel HD Graphics and a 23" HPW2371d monitor with native resolution of 1920x1080. This monitor shipped with a VGA cable and adapter and it is plugged into a DVI port on desktop. I can only run the resolution at 1024x768. If I choose 1920x1080 it doesn't fit to screen. Can someone please explain what needs done to correct this.

    If you are showing a "non-plug and play" monitor in the Windows device manger, I would guess is a problem with the "DDC-EDID" communictaion link between the computer and the monitor. Either the monitor isn't reporting, the computer isn't reading, or the link (cable) is damaged. If you have another monitor and/or computer and/or VGA cable, try swapping them around to determine where the issue is.
    Examples...
    1) HP Elite H8-1240t with different monitor
    2) HP W2371d monitor with different computer
    3) Repeat 1 or 2 with a different VGA cable
    4) Try a different DVI-to-VGA dongle adapter with the HP Elite H8-1240t and HP W2371d monitor
    5) Try a different VGA cable with the HP Elite H8-1240t and HP W2371d monitor
    6) Try a different DVI-to-VGA dongle adapter and a different VGA cable with the HP Elite H8-1240t and HP W2371d monitor
    If you can't identify the issue from the steps above, you may wish to manually set the Windows resolution to 1920 x 1080 and set the refresh rate to 59 or 60 Hz.
    Please send KUDOs
    Frank
    {------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
    Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
    This is a user supported forum. I am a volunteer and I don't work for HP.
    HP 15t-j100 (on loan from HP)
    HP 13 Split x2 (on loan from HP)
    HP Slate8 Pro (on loan from HP)
    HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
    HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
    HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
    HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
    HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

  • Macbook Pro 15" Model - Native/Forced Resolutions

    I'm looking into buying a 15" Macbook Pro, but the only thing holding me back is it seems like it can only support 1440x900 as its native. Is there an upgrade I can buy for it from apple to achieve somewhere around 1920x1200 like the 17" model, or is there anyway to force the resolution? My last option would be to buy the 17" model.. I'd rather not though because I don't like the amount of space it takes up/the hand room on the base haha.
    Thanks for the responses
    John

    I have the 15" model with the $150 BTO option of the 1680x1050 display. You can't force a display past it's native resolution. It only comes with so many pixels

  • Imac and external projector resolution problem!!!!!

    hello! I´ve benn using an imac24" for about 4 months. When I attached my projector with a capasity for 1024x768 85Hz while my imac´s is 1920x1200.
    My problem is that I want my imac to use it´s highest resolution at 1920x1200 while my projector is using 1024x768. Is that posible, and if, how would I make it happen?
    //Wilhelmsson.
    Imac 24", core 2 duo   Mac OS X (10.4.10)  

    You can only do this if you have the system set for "extended desktop", where the images on the two screens will be different. If you want to run the system in "mirroring" mode, where the iMac's screen is duplicated on the projector, then the resolutions have to match, so you'll have to reduce the iMac's screen to 1024x768 to match the maximum resolution of your projector.

  • Auto detecting projector resolution?

    my wife teaches college and uses an overhead projector often. i'm trying to get her to use her macbook and keynote so she can use the remote (she takes her macbook to school anyway), but whenever she plugs it in, the projector shows the wrong resolution on the screen (it's 4:3, by the way). and the resolution on her macbook is out of whack, too, when it's plugged in (desktop is way too big for the screen, meaning you can't access a bunch of stuff on the top - including display preferences.)
    my question is: can it be set so all you have to do is plug in the projector to the macbook and both display the proper resolution?
    bonus question: can it be set so the macbook has the proper resolution when you unplug it from the external projector - i've had her call me several times to rectify this over the phone.
    thanks!

    BSteely wrote:
    OK, well without further information, I will take a swag at this. I am guessing the projector is really old and may only support a max resolution of 640 x 480, or possibly 800 x 600. In mirror mode, that means that both screens, e.g. the MacBook's and the projector's, must run at the same highest common resolution. But running the MacBook at 640 x 480, you are right, a bunch of important stuff may not fit on the screen. So that is my guess why she can't "simply plug it in and have it work."
    She might be better off running non-mirror mode and just using the projector as extended working space. Then she will have to drag the window containing the information she wants her audience to see onto the other (projector's) display area. That's all I can think to do.
    i appreciate the input - especially without a lot of information. i may try the mirror mode.

  • Screen/Projector Resolution in Windows

    We've just setup around 50 or so new iMacs that we're running Windows Vista on via Boot Camp. We're having some trouble connecting projectors to them that we haven't had with previous models.
    We can get the projector to mirror the image with no problems, but for some reason we seem to be limited to a resolution of 800x600 when we do this. The projector and, of course, the iMac display are capable of much higher resolutions. If we disconnect the projector, we can set the display resolution to whatever we want. If we boot to Mac OS, we have no problem scaling up to higher resolutions on both the built-in display and the projector--so it would seem the hardware (nVidia geforce 9400, as I recall) is definitely capable.
    Is there some little setting somewhere that I'm missing?

    Hi Veronica,
    just to rule ou the obvious:
    Have you installed the BootCamp Windows Drivers from the OSX DVD yet ?
    If not, while in Windows pop in the OSX DVD and the Driver Installation should start automatically.
    Stefan

  • Is it possible to publish a project with a different resolution than the native project resolution?

    I think I know what the answer is going to be here, but I'm going to ask anyway. The background here is that I've made a few demo videos for new products and features my company is working on. I'm using CP4 for this. Our marketing department wants to take AVIs of my demos and insert them into their Powerpoint demonstrations. However, the native resolution of our demos doesn't make for a graceful import into Powerpoint. Thus, I've been directed to provide smaller res AVI files.
    Thus, I am wondering if you can publish a project at a different resolution than the one in which it was recorded. My initial poking around seems to indicate that the answer is "no," and if this is truly the case, I will be rumbling over to the "Suggest a Feature" forum soon. There does seem to be a kind-of-workaround in that you can change the resolution of the project before publishing it, but this is something that cannot be undone, meaning that in order to do this, I will have to save new, smaller versions of all my projects. This is a bit ungainly.
    So, if anyone knows a good trick here, I would love to hear it!

    Unfortunately, I don't know what you mean when you say "manual panning." And I'm really not sure what you mean when you say the fields are not fully visible in the original image; they are completely visible. Here's a close-up from the original slide:
    As you can see, the fields are completely visible.
    Also, the slide is not entirely static. For the slide I chose as an example, the Password is filled in before the mouse moves. This typing may be part of what is getting Captivate confused; note this sequence from the resized version of the project:
    Slide 35:
    The login window first appears. Everything is normal. During this slide, the mouse moves and clicks inside the User ID field, leading to...
    Slide 36:
    At this point, things begin to go awry. The user name is entered, and the cursor moves to the Password field.
    Slide 37:
    Whoops! As soon as we click Login, everything goes back to normal.
    Slide 38:
    I will try a few of the suggestions you offered, and will report back with the results.

  • Should I match STD preview size to native screen resolution or the resolution I am actually using?

    My iMac 27" monitor is 2560 pixels wide but I run it on a screen resolution of 2048 x 1152. Would it be a waste for me to set the Lightroom Standard Preview Size to size to the setting of 2880? I am thinking I should set the Standard Preview Size to 2048 to save space on my hard drive. What do you think?
    When I set my monitor to the native resolution the text on menus etc is pretty hard to see with my tired old eyes. Is there a disadvantage to using  2048 x 1152 on my 27" monitor when using Lightroom?

    DanATD wrote:
    I am thinking I should set the Standard Preview Size to 2048 to save space on my hard drive. What do you think?
    If I were you, I'd use Jeffrey Friedl's Online Lightroom Configurator to bump the font-size of the text, and leave the monitor resolution at 2560 (and standard previews at 2880). Unless of course you can't see image detail all that well either with the increased resolution. There may be some text that jf's configurator can't reach - dunno, but it may be worth a shot..
    If bumping font size (and monitor rez) doesn't pan out, then the answer is yes: 2048 is sufficient resolution for standard previews, at a monitor rez of 2048.

  • Satellite Pro U400 - How do I get the native screen resolution for external monitor?

    I have a samsung syncmaster external screen connected to a Satellite Pro U400.
    The screen resolution only goes up to 1280 etc however the samsung minimum is 1440 x 920 (ish I forget).
    How do I get the samsung to display the whole enlarged screen to save my eyes from the realativively small internal screen?

    Hi
    > The screen resolution only goes up to 1280 etc however the Samsung minimum is 1440 x 920 (ish I forget). How do I get the Samsung to display the whole enlarged screen to save my eyes from the realativively small internal
    I??ve got a U400 which was equipped with the Intel graphic card and I??ve got an external LCD which I have connected to the U400 using the DVI-to-HDMI cable.
    My U400 unit supports the HDMI and the LCD the DVI port.
    I have received also the driver disk with my LCD and I have installed the software.
    I have also update the Intel driver and used one from the Intel page.
    Now I have the access to many different external resolutions and can choose it.

Maybe you are looking for