NativeWifi application not recognizing Miniport Driver over USB

Hi,
We are working in WEC7 Wifi driver over USB interface. We have developed the custom miniport driver.
In our case, when we analyse the Debug prints, Wifi driver is up and scanning properly. But Native Wifi
application is not able to display/indicate anything on UI. It is showing the Adapter as OFF. Same Miniport driver is working fine over SDIO.
Any registry settings or configuration related changes is needed please let me know.
Thanks,
Seeth

The problem was solved by unplugging the printer (not just power off), waiting 5 minutes, plugging back in and restarting. Everything is working like a charm - USB, wireless, etc.
Found the answer as a response to another similar post in this forum.

Similar Messages

Recovery media program not recognizing flash drive in USB port

I have a new NB505-N500BL netbook. I am trying to create a backup using the Toshiba Recovery Media Center.
However, it doesn't seem to recognize that I have an 8GB flash drive installed.
Everytime I hit "create," I get the message to insert a 7.7GB flash drive. When I hit "OK" I get a msg to insert a flash drive greater than 7.7GB.
The 8GB flash drive is installed. I've tried it in all 3 USB ports. I've tried inserting it before turning ont the computer and afterwards.
I bought the flash drive directly from Toshiba so it should be good. I also assume a new 8GB flash drive meets the requirements of 7.7GB.
Any suggestions?
Thanks!
Emma

Hi Emma,
Contrary to what the size it's asking for, it's possible that the drive is just slightly too small. Even though the data may fit on the drive you have, the way TRMC calculates its free space may be slightly off. If you wish, you can try building this by hand and see if it fits. As follows:
1. First format the USB drive and make it active.
2. Now reboot the machine hitting the <F8> key until you are presented with a menu.
3. The first option should be "Repair...", then hit <ENTER>
4. You will be present with two login screens and eventually arrive at a repair menu.
5. First open up a command box and leave it open.
6. Now go back to the menu and launch the "TOSHIBA Recovery Wizard".
7. It will eventually get to a warning screen. Don't go pass this warning screen.
8. Once it gets to the warning screen, toggle back to the command box.
9. All you need to do is copy the contents from (I believe it's drive Q:\" to you root of your USB drive.
"robocopy Q: (USB Drive letter) /E /R:1 /W:2
10. Once everythings copied (assuming it fits), <Cancel> and the warning screen and then try rebooting from your USB drive.
Rick...

Usb port not recognizing external drive

When I plug my external backup drive, Lacie, into either USB ports on my MacBook Pro, it is not recognizing the drive. Not sure if I powered down incorrectly. It use to recognize it. Help.

Start by looking for the drive in the Apple System Profiler (from the Apple menu's far left Apple logo>About This Mac>More Info>Hardware (in left column) >USB.) If the drive is correctly powered and connected, it will show up here.
If it doesn't show up, the problem is with the drive. With the drive plugged in, put your ear to the drive and listen for the whirring sound the drive makes when it is powered up. If it isn't making any sound, ot's either a bad drive or a bad power supply.
If the drive is making sound , then the problem is probably the USB cable or your USB port. Try a different USB cable. This should fix the problem; if all the above tests were good and the drive still doesn't mount, it may be the USB controller in the Mac. That's a serious problem that requires repair or installation of an aftermarket USB controller.
Hope this helps

My toshiba satellite e105-s1802 do not recognized my a4tech pocket usb hub pls help me with this?

my toshiba satellite e105-s1802 do not recognized my a4tech pocket usb hub pls help me with this?

I AM HAVING THE SAME PROBLEM WITH THE SAME MODEL. I GOT THE SERVICE
MANUAL AND I'M THINKING TO OPEN IT AND SEE IF THERE'S SOME PHYSICAL BAD CONNECTION
INSIDE. BUT LIKE YOU SAID. IT'S ONLY THREE MONTHS OLD.!!! I DON'T WANT TO RUIN THE WARRANTEE.
BUT THIS IS VERY FRUSTATING. I WANDER IF TOSHIBA DOES THIS ON PURPUSE.!!! KEEP IN TOUCH AND
IF YOU NEED THE SERVICE MANUAL CONTACT ME AT [email protected]
THANK YOU.!!!!

I have updated my adobe digital editions but application not recognizing it, can't open epub book

I have updated my adobe digital editions but application not recognizing it, can't open epub book

What Adobe Digital app on your iPad? If you are talking about a third-party app (like Bluefire Reader) you need to connect your iPad to your computer, open iTunes, select the iPad, and select Apps in the Sidebar. Scroll down to the File Sharing section, select the app you plan on using, select Add (bottom right), navigate to where the book is on your computer, select the book and sync your iPad.

Photoshop not recognizing graphics driver

I have a brand new Sony Vaio i7 core, 8 gig's of ram and 1Tb hd, and I get this message whenever I fire up Phontoshop: "Display driver has stopped responding and has recovered. Say's I need 512Meg of Ram, but I have 8Gig's of Ram. The the message is followed by a pop-up that says the video driver may need to be updated, but I checked and it doesn't. It says it can't do 3d, I don't need it too, but it's annoying that it's not recognizing a driver on a brand new computer. Any ideas if there is a way to get this working properly? Thanks!

There is no "Photoshop online".
What version of Photoshop are you using?
And the display driver message refers to bugs in your display driver, plus the requirements to have 512 Meg of VRAM (not RAM) on your video card to use the 3D features.
You need to update your video card driver from the GPU maker's website to pick up all the latest bug fixes. Updates from Microsoft are years out of date.

ATP Photo Finder GPS not recognized on Mac as USB flash drive

Much like the problem with the Sony GPS-CS1, it appears the ATP Photo Finder device also will not be recognized as a flash drive on a Mac. Tiger worked with the Sony for awhile, but recent updates (as well as Leopard 10.5.x) have made it no longer work. There are other topics on the GPS-CS1 in these forums detailing those problems.
I picked up an ATP Photo Finder from My Discount Digital to try it out. It logs data, then you insert the memory card in to the device and it will GPS stamp the JPGs. It sounds like a great idea, but when it didn't work I was going to have to plug it up to my Mac and use PC software via Parallels to reprocess the images.
It is not recognized -- and under Parallels, a new USB device shows up simply listed as "U" under the pull-down menu. When I try to select it, it claims it is already in use. Methinks Apple Mac OS X is semi-grabbing the device but not being able to use it.
Odd.
So I post this in case others have the ATP Photo Finder and have problems... Maybe we can figure something out.

Well, here's an odd (and quick) self follow-up... I was reading an Apple Help file and it suggested looking at the System Profiler to see if the device is being recognized. Indeed, it showed the "U" and some garbled characters (so something is not quite right). It also showed it was plugged in through my powered USB hub. I bought this hub after running in to issues with devices that would not work plugged in to the iMac keyboard... On a whim, I plugged the ATP Photo Finder in to the non-powered USB port on the keyboard and ... it worked. It still shows up as U(garbled) but I was able to access it from the Mac Finder.
Interesting.

Shuffle 2 - device not recognized... USB Driver?

I got the Shuffle 2nd Gen, plugged it into my PC, and it blinks orange with no install box on Windows, and a "device not recognized" error. Nano works fine on my computer, and my Shuffle works fine on a Mac laptop, so customer service told me it must be a problem with an outdated USB driver.
Here's the problem: I don't know where to get the USB driver update, because my PC is custom made, and I don't know who the manufacturer is. The customer service guy says to find the maker of the motherboard, but I'm not 100% sure how. My Device Manager says "VIA USB Enhanced Host Controller" is the only listed Enhanced (2.0) USB Port. I used a program to find the motherboard manufacturer, and I think it's a "Chaintech 7VJL APOGEE."
Can anyone help me find a USB driver? Might something ELSE be the problem?
(I'm reposting this from a reply I wrote to a different thread)
iPod Shuffle 2nd Generation Windows XP Custom PC

Hey 655micha,
I'm sorry you're having an issue with a USB device. Do you get an error window that pops up? If so what does it say? Have you checked Device Manager? Is is just one device that isn't working? Has it ever worked before? Is it just one USB port in particular that isn't recognizing devices?
What model do you have? Here are the steps to find your product number. FN + ESC is the easiest way to find that information.

IPhoto does not sync with iPhone over USB anymore

I'm using iPhoto '11 (9.4.2) on OS X 10.8.2 and an iPhone 4S (now with iOS 6.1.2).
A few months ago when I connected my iPhone over USB iPhoto would start and do the expected workflow as it still does when I connect any other camera: Import the new images and delete them on the iPhone.
Since around I installed iOS 6 on the iPhone iPhoto will not start anymore when the iPhone is connected. When started manually it will show the iPhone but not recognize any new images.
I don't (want to) use Fotostream.
I have looked for other answers and the usually suggested restarting / resetting has not helped.

Main drive apple powerbook
Have tried changing libraries to backups on external but same result. They work but not recognized by other programs. All are named iphoto library

USB Device Not Recognized on Windows 7 - USB mouse

I have a 4 week old Inspiron 1545 with Windows 7 Home premium that has developed an error: USB errors while trying to install a Microsoft USB mouse on this Laptop. Interestingly, my Microsoft USB Mouse installed perfectly first time and worked for about 2 weeks, and then failed. In looking at the system restore points, it tells me that there have been two driver updates to the USB environment since the unit was shipped from Dell. I wonder if an automatic update from Microsoft has somehow inadvertently updated or replaced a Dell factory driver.
Two nights ago I spent 45 minutes with Dell tech support doing remote control bug fixing on this laptop. They werent able to fix it (in the time allowed). They downloaded at least one of their newest drivers onto this machine and rebooted it - and they seemed pretty savvy - but still not working. So I went ahead a did a system restore to a point about 10 days back because I could see that a USB driver would be affected (as shown in the system restore menus), and I would like to compliment Microsoft on this very cool functionality!
At this point, I've unplugged the USB mouse , used the Device Manager to delete the 'unknown device', and done a system restore back to what I suspected was a working point. But still getting a 'Device not recognized' warning every few minutes, and still don't have a working mouse. I don't want to have to do system restores back to pprevious dates, although I suspect this is one solution.

Hello,
I just wanted to let u know, I had this same issue for about 2 weeks. Basically what happened was a bad install of my AMD Chipset drivers. When I attempted to upgrade, the install didn't go all the way through.
I then restarted my system, and BAM! No Mouse or Keyboard functionality thru USB.
Even when I went into SAFE MODE the Mouse and Keyboard were not functional. The only time they worked was when the computer first attempted to start, BEFORE windows loaded.
So, this means that your issue is a software problem.
I thought it was some other software that I installed, and ran a restore session, but that wasn't the issue. Still no functionality.
I even tried removing my CMOS battery, to reset it, since some people said that had solved their problems...Still nothing.
I then read other forums around the web using my Android phone to try and find a solution, only those solutions were no help.
I was also advised to run: MSCONFIG and Hide all Windows programs and then stop every other driver, source from loading (of course if my mouse and kb worked, I would have tried that).
I had even read that because I was using USB, that I should try using a PS/2 Mouse and Keyboard connection.
It took me 2 weeks to get the correct PS2 adapter that worked, which would essentially allow me access to my system again...
I Purchased a USB A Female to PS2 (MDIN6) Male Adapter (for Mouse) from http://www.SFCable.com
This my friends, was a lifesaver. I only have one PS2 port on my system, so I used my mouse to try every option I had previously read about. Of course you cannot type because the keyboard doesn't work, so you need to know the location of the folder where
the programs you are trying to run are.
So, a little after I got back into my system, and I closed down all programs, the warning screen came up that ALL of my USB Ports failed and could not be updated. I even Uninstalled every last USB port from the System Properties and restarted, and still
that didn't work.
I had forgotten that during the time when this problem arose, there was a failed install of my AMD chipset drivers, so luckily I had not deleted the source file and I tried to reinstall, and VIOLA! I'm back up and running and my USB ports are restored
and everything is working!
I hope this solution is able to help other people out there.
Thanks,
JE - [email protected]

Booting from an external drive over usb

Hey, has anyone else had any problems booting from an external? I have an external lacie drive that I keep a clone backup on (using superduper) and usually have it connected with firewire400. I know it works because i've accidently booted using it before, but recently the firewire port on it died so i've been using usb instead.
Now the problem, holding option on my macbook starting, I get no options to choose from. If i have the mac osx dvd in, it pops up so I know it's not a problem with my macbook. It is possible to boot from usb correct? Everything i've read has said it's possible... I'm not sure why my external drive isn't coming up. I know it works over usb because I've used it alot since the firewire port died on it. I checked in the disk utility and it does say it's bootable, and afterall it's cloned using superduper like i said before...
I have 2 partitions on the drive, is that a problem? It never was before, I've booted off it many times before using firewire though. Can someone help me out here? Very annoying as I'm replacing the HD in my macbook and neeeeeeed to get on my external.
When I asked the guy at the genius bar awhile ago he just said it was probably a problem because my old internal HD died and he said sometimes it causes the macbook to not even be able to get as far as the point to boot from another source. Well now I have a new working drive in it, so I know that's not the problem. It just doesn't show up to boot from anymore, ugh.

Sounds like your clone isn't bootable. Have you tried the following:
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger and Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
If DU reports errors it cannot fix, then you will need Disk Warrior (4.0 for Tiger, and 4.1 for Leopard) and/or TechTool Pro (4.6.1 for Leopard) to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.

IPod not recognized by laptop's USB 1.0 port

There are a couple of problems here. I have an external hard drive that can only be accessed with a USB 2.0 cable. I had to buy a card with USB 2.0 ports since my laptop only has USB 1.0. When I try to update the iPod (plugged into the USB 2.0 card as well as the external hard drive), everything freezes, goes very slowly, and I can't transfer songs from the external hard drive.
When I unplug the external hard drive I can update songs from my laptop's hard drive, but the iPod has to be plugged into the USB 2.0 card. When I plug the iPod into the laptop's USB 1.0 port (regardless of whether the external hard drive is connected) the iPod is not recognized, it only gets charged.
I tried this iPod on a different computer last night and it worked great.
So two questions: 1) how do I transfer songs from my external hard drive (get my computer not to freeze) and 2) how can I make my laptop recognize my iPod when it's plugged into the laptop's USB 1.0 port?
Thanks a lot

Well... from what i am reading about your post, you want to transfer your music from the external hard drive to your laptop. if this is correct then i think that you should open the hard drive into a window and put all the music into 1 folder and drag it onto your desktop, then once the music is downloaded onto your laptop, (if there is enough space) unplug the external hard drive and use the USB 2.0 port 4 your ipod w/o the hard drive. sometimes when i plug my ipod into my PC it will stop everything for 5 minutes then it starts to work. so i recommend to plug it into the 2.0 and wait a while and see what happens.
Windows XPee

Macbook Air not recognizing anything connected via USB?

My MB Air is not recognizing anything that I connect via USB...camera, harmony remote, phone, toys - nothing! Nothing is showing up as being recongnized...anyone else having this problem? I have tried virtually every device...what the heck?

SMC reset and re verify
SMC reset
Shut down the computer.
Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
Release all the keys and the power button at the same time.
Press the power button to turn on the computer.
Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC.
If no USB device of any kind can be found contact Apple for appt. for free in shop full diagnostic and likely parts replacement.

ATV1 not recognized by iTunes (over Wi-Fi)

Hi guys!
My ATV1 is not recognized anymore by iTunes. I tried everything (Apple tips, searched the discussions pages), but had no luck. I even erased the connection and started all over again, only to find the same result. However, the ATV is connected to the internet, and I am able to listen to the radio and everything else.
When I try to add Shared iTunes Library, the ATV becomes available again, but when I try to sync, iTunes gives me the port 3689 blocked error, and and afterwards the ATV dissapears from the Device list. The Apple tip on this problem doesn't do anything to solve it.
Any idea on what I might do? Could it be the router (Huawei HG655b)?
Thanks in advance for your help.

Hi Linda Custer,
It seems you are experiencing issues with iTunes Wi-Fi sync. That does sound troublesome. The following article provides steps which may help you find a solution:
Troubleshooting iTunes Wi-Fi syncing - Apple Support
Thank you for contributing to Apple Support Communities.
Take care,
Bobby_D

TOUCHSMART 520 PC NOT RECOGNIZING DEVICES IN THE USB PORT.

When I plug any devices into the USB port, they are not recognized. The computer acts as if they are not there. The devices (MP3, camera, Garmin, etc) turn on, so I know that they are connected. The Printer and wireless mouse that connect through the USB port still work and I have tried changing ports...it doesn't make any difference. Even if I try to search for thr device, the computer does not find it. Any ideas?

Hi DJOBES,
Welcome to the HP Community, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
Sorry to hear about your USB issues. I will be happy to assist you but I need some additional information; what is your operating system and product number?
Thank you,
Please click “Accept as Solution ” if you feel my post solved your issue.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Thank you,
BHK6
I work on behalf of HP

NativeWifi application not recognizing Miniport Driver over USB

Similar Messages

Maybe you are looking for