NB550D - battery icon does not always reflect the proper balance of time

I have just recently purchased an NB550D and I must say that at the outset I am very happy with it. It does tend to be a bit slow but I can live with that.
My problem however is that the battery icon does not always reflect the proper balance of time. For instance after a full charge it may show 9 hours remaining but after a shutdown and restart it will may show 75% and 3 hours remaining. If I shut down and restart it may show 75% and 6 hours remaining
When I first started the unit I allowed it to fully discharge (through use) three times as was suggested by the salesman at the store but quite candidly it doesn't seem to have made one scrap of difference!
Any advice will be appreciated.
Regards

Remaining time is not credible value of the battery state - it depends on actual duty of processor and the program wich estimates this sometimes shows wrong that time or corrects this after a while. Percentage of charge of battery is much better factor to use!
But in case your battery loses from 95% to 75% after restart indictates that's something wrong with the battery or program... In my NB550D after restart (pause for 1 day) the battery loses only 2-3% .

Similar Messages

  • My battery icon does not always show in panel (multiple DEs)

    I've been meaning to ask this for a while. I kind of asked in passing not really looking too hard for an answer. And from what I heard others aren't having this issue, but then again I didn't ask very in depth.
    On my laptop if I plug in my power cable I can see my battery icon in the panel, then when I unplug it I can see the battery icon. However, after a certain amount of time of being unplugged the icon in the panel disappears until my laptop gets really low on power. Then it reappears. If I plug in my power cable and then remove it I get my panel icon back immediately, but only for a short time.
    I was using XFCE and thought it might be a problem with the new Power Manager. Whenever the icon would disappear I could go into the Power Manager settings and it was never wrong. It always told me correctly if I had a line in or line out.
    So I tried with GNOME and the exact same thing happens. i haven;t tried with any other desktop environments. Has anyone seen this issue?

    No, I've not seen it.
    Look at the pseudo files in /sys/class/power_supply.  On my system, these are the interesting ones:
    ewaller@odin ~ 1048 %ls /sys/class/power_supply/BAT0
    alarm capacity_level charge_full_design current_now device model_name present status technology uevent voltage_now
    capacity charge_full charge_now cycle_count manufacturer power serial_number subsystem type voltage_min_design
    ewaller@odin ~ 1049 %cat /sys/class/power_supply/BAT0/voltage_now
    12467000
    ewaller@odin ~ 1050 %cat /sys/class/power_supply/BAT0/charge_now
    3670000
    Ensure that these files are not appearing and disappearing.  Also, check their contents and see if the data are rational
    Last edited by ewaller (2014-12-24 17:25:27)

  • Icon does not appear in the image thumbnail in Bridge

    After processing a camera raw file using the Camera Raw plug-in, an icon does not appera in the image thumbnail in Bridge. Using raw plug-in created april 19 2007 in windows vista. The same CS2 program does create the icon on another computer using Windoes XP. Jim

    Please check your top toolbar left side, you should see a small arrow icon to expend the toolbar, located near the Tools option
    (Ignore the location side in the sample picture, it should be the opposite for your language )
    If you cannot locate the HP Smart Web Printing there either, Click Tools > Manage Addons
    and make sure the HP Smart Web Printing addon is enabled,
    Say thanks by clicking the Kudos thumb up in the post.
    If my post resolve your problem please mark it as an Accepted Solution

  • Recently when I install apps, the icon does not appear on the menu screen, also, it shows that it is down loading at the app store and when complete, I can not open it or reinstall it.  Help Please   o,

    Recently when I install apps, the icon does not appear on the menu screen, also, it shows that it is downloading at the app store and when complete, I can not open it or reinstall it. Has happened on the last 4 free apps. Help Please

    Reset your iPad. Press and hold both the power and home buttons for 10-15 seconds till the Apple logo appears. Release both buttons. Wait 15-20 seconds till you iPad starts on it's own. Now try and download an app.

  • Bootcamp disk icon does not appear in the System Preferences/Startup Disk. Any help ideas ?

    Everything works fine but the Bootcamp disk icon does not appear in the System Preferences/Startup Disk.
    When I am in Win7 I am easily rebooting my iMac by right-clicking on the Bootcamp icon.
    When I am in Mac OS I wish to do same but that Bootcamp icon does not appear. Everytime I am restarting my iMac and pressing on the Option key to select the Windows disk.
    Does anyone have an idea how to adjust to bring the Bootcamp icon to the Startup Disk panel ?

    Use BootChamp instead; perhaps you have an NTFS 3rd party driver installed and has its own control panel.

  • After installing an App, the icon does not appear on the desktop?

    After installing an App, the icon does not appear on the desktop? Where would I find it?

    Some people have found that an app (usually iBooks for some reason) hasn't appeared on a homescreen until after the iPad has been reset and has restarted : press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.
    Also depending on what the app is have you got an age rating set in Settings > General > Restrictions that is hiding it ?

  • I have added about 2000 cds to itunes without the song details. as i slowly update the song titles and genres etc in itunes, it does not always update the file in explorer. is there a solution to this? thanks.

    i have added about 2000 cds to itunes without the song details. as i slowly update the song titles and genres etc in itunes,it does not always update the file in explorer.is there a solution to this? thanks.

    Windows Explorer will display tag properties for mp3 & wma files, not aac (m4a) or wav. It is possible for mp3 files to contain multiple tags but only one will be displayed. Try inspecting the problem fils with a third party tag editor to see if you can tell what is going on. For mp3 files, provided all the details that you want the file to have are displayed in iTunes, you can try using the right-click option Convert ID3 Tag > None a few times followed by Convert ID3 Tag > ID3v2.3 which may well help.
    tt2

  • I have a imac mid 2011 model, why can't i connect to airplay?  And the airplay icon does not show in the menu.

    I have a imac mid 2011 model, why can't i connect to airplay?  And the airplay icon does not show in the menu.

    Hi there cjperido,
    You may find the troubleshooting steps in the article below helpful.
    iTunes: Troubleshooting AirPlay and AirPlay Mirroring
    http://support.apple.com/kb/ts5209
    -Griff W. 

  • Have a 10.6.8 mac and the icloud icon does not appear on the system preferences

    Hello,
    I have a 10.6.8 mac and the icloud icon does not appear on the system preference, even if I'ved upgraded the software.
    Renee

    The minimum requirement for iCloud is Lion 10.7.5 (Mavericks preferred): the iCloud Preference Pane does not appear on earlier systems - the MobileMe pane appears on Lion and earlier but is now non-functional - you cannot now open or access a MobileMe account.
    To make use of iCloud you will have to upgrade your Mac to Lion or Mavericks, provided it meets the requirements.
    The requirements for Lion are:
    Mac computer with an Intel Core 2 Duo, Core i3, Core i5, Core i7, or Xeon processor
    2GB of memory
    OS X v10.6.6 or later (v10.6.8 recommended)
    7GB of available space
    Lion is available in the Online Apple Store ($19.99). Mountain Lion (10.8.x) is also available there at the same price (though it's reported to have been removed from sale in some countries so may well cease to be available generally) but there seems little point as the system requirements are the same for Mavericks (10.9.x) - which is free - unless you need to run specific software which will run on Mountain Lion only.
    The requirements for Mountain Lion and Mavericks are:
    OS X v10.6.8 or later
    2GB of memory
    8GB of available space
      and the supported models are:
    iMac (Mid 2007 or newer)
    MacBook (Late 2008 Aluminum, or Early 2009 or newer)
    MacBook Pro (Mid/Late 2007 or newer)
    Xserve (Early 2009)
    MacBook Air (Late 2008 or newer)
    Mac mini (Early 2009 or newer)
    Mac Pro (Early 2008 or newer)
    It is available from the Mac App Store (in Applications).
      You should be aware that PPC programs (such as AppleWorks) will not run on Lion or above; and some other applications may not be compatible - there is a useful compatibility checklist at http://roaringapps.com/apps:table

  • After installing FF 6.02 on Windows 7, the icon does not appear on the desktop and the program does not appear in the All Programs menu

    I just received a new laptop running windows 7 home premium and wanted to install Firefox on it. I tried to install the most recent version. When i installed 6.0.2, the icon did not appear on my desktop (it was a hidden file in my desktop folder) and the program group does not appear in the start menu's All Programs list. The program *does* run though, at least it did a few times. This happened whether i installed as administrator or not. Installing firefox 3.6.22, though, DID create the program group and desktop icon, and upgrading from there removed them again. installing other programs (e.g. vlc, trillian, etc.) did not cause this behavior. I also tried this both with and without McAfee's realtime protection running.

    Some people have found that an app (usually iBooks for some reason) hasn't appeared on a homescreen until after the iPad has been reset and has restarted : press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.
    Also depending on what the app is have you got an age rating set in Settings > General > Restrictions that is hiding it ?

  • Menu Bar - Sound Volume icon does not move with the press of the F key

    So I normally press the F keys to control the Sound Volume, right, just like everyone else does -
    but the Sound Volume icon in the Menu Bar at the top right does not respond to the F key at all!
    Isn't it supposed to react simultaneous with the press of the F key?
    I have to actually use my mouse click to make that volume go up and down.
    The actual volume does work with the F key, it goes up and down.
    But to make the 2 work in sync, I have to point the mouse to the one at the Menu Bar, fiddle with it, and then I can use the F key and both work together at the same time.
    If I haven't touched the Menu Bar one for a while and I only use the F key, the Menu Bar one doesn't move at all.
    It's weird. Any ideas?

    I see what Al is seeing. Normally I just use one method or the other. The Volume Adjustment keys provide visual feedback, so it's unnecessary to check the menu extra, i.e. the Volume menu bar icon, to see the same feedback.
    The slight delay in the reaction of the Volume menu extra, when open and while adjusting the volume with the Volume keys is normal.
    They're independent methods for adjusting the Volume setting. The Volume menu extra takes a moment to refresh when the slider is displayed and you're changing the setting via the Volume keys.
    Good luck!
    Dr. Smoke
    Author: Troubleshooting Mac® OS X

  • "Battery serial does not validate", but the number is within the range

    My sister came home from abroad for Christmas, and I checked her PB 12-inch battery serial number. Her battery has the serial number ZZ3480FJPVEA as far as I can see. This falls into the replacement range:
    12-inch
    iBook G4 A1061 ZZ338 - ZZ427.
    On the exchange page, Apple writes: "If the first 5 digits of your battery’s 12-digit serial number fall within the noted ranges, please order a replacement battery immediately." But the battery serial does not validate even if I replace the zero with the letter "O".
    Are there batteries within the range that still are ok?
    Ingmar
    PowerBook G4 12-inch   Mac OS X (10.4.8)  

    I could not post an answer to the topic without marking the question
    "answered", though it wasn't!
    Strange, because the question is not marked as answered and it is not necessary to mark it in order to reply (simply click on the "reply" link near each post you want to reply to).
    However when you feel that your question is answered - or the forum cannot be of further assistance - mark the question as answered and maybe also give some final notes.
    If you got helpful replies, then you may award the posters by granting points. You can do so by clicking to "helpful" and "solved" buttons appearing near each post (you need to be logged in).
    The buttons mean what they state: "Helpful" in the sense of user gave a useful answer or further information allowing you to solve an issue with some work of your own. "Solved" means that this post of the user is mainly responsible for managing an issue.
    You can only mark one posting as "solved" in a thread, and - I hope this is correct - two or three times marking posts as "helpful". With the last, I'm not sure, you may have a look at "Help & Terms of Use".

  • Top right battery icon does not show battery usage

    So over the weekend I did not charge my iPhone, because the icon always said I had full battery life. I believed it because I never made a call, listened to music/video or surfed the net. It basically stayed in sleep in my pocket both days.
    I get to work monday, pull it out to listen to music and I get the full screen battery icon showing the battery is dead with the plug and lightning bolt icons under it, then it turns off on its own. If I turn it on again, same deal.
    I get home, hook it up to my PC and charge it, it works fine.
    Today i've been listening to the iPod all day and surfing the net on EDGE and the battery icon in the top right shows full battery. To test I turned WIFI on for the past few hours to check and it's still showing full battery.
    Basically just the battery icon in the top right isn't recognizing the battery being used. My Usage stats in Settings are also blank for Time Since Last Full Charge.
    Background info:
    Refurbished iPhone bought directly from ATT, came with 1.1.1, immediatly upgraded to 1.1.4
    I've tried hard reboots.
    I keep push e-mail and WiFi off at all times. WiFi comes on very rarely and only for short amounts of time.
    I keep the phone connected to my PC overnight, but the PC does not go into any sort of sleep mode(ruling out not charging overnight)
    I'm going to go home tonight and restore the phone to see if that helps, but I wanted to see if this is hardware related or software. This just started this weekend and i've had the phone for a few weeks now, and other than some short battery life at the beginning when I would keep wifi and push e-mail on a lot, or the random Safari closings, no other issues.
    Message was edited by: D0rk4L

    DOrk4L,
    Have you tried re-calibrating the battery? To re-calibrate it, let the battery drain completely and then charge it fully. You should see correct battery usage after that.
    Hope this helps,
    Jennifer B.

  • AppleWorks Icon does not stay in the same position after saving

    After I installed AppleWorks 6.2.8, each time I save the file (word prosessor or data base) the icon on the desktop always moves to the right side of the screen below the hard drive icons. If I drag it to different position, then save the file it will move to the right side of the screen. If the saved file is in a folder, it always goes back to it's origional position. In fact, the same thing happens to other applactions (PhotoShop, TurboCad, etc.). This only happens in OS 9.2.2. It does not happen in OSX 10.4.6. The same situation also happens on my iBook and PowerMac G4 MDD after installing AppleWorks 6.2.8.
    My System: PowerMac 7300, Sonnet 1GHz G4, 1GB memory, OS 9.2.2, OSX 10.4.6
    I checked the AppleWorks preferences and Control Panels and could not find any settings.
    This does not happen with AppleWorks 5.
    Anyone know what has happened? Are there settings I am missing?
    Much Thanks,
    Gene
      Mac OS 9.2.x  

    Hello
    If I remember well, AppleWorks 5 was saving one document by rewriting the old one. Doing that, all the file's attributes where kept.
    AppleWorks 6 writes an entirely new file, so the icon is not preserved. Of course, some of us think that it would have been a good idea to keep the parameters of the old file and "paste" them to the new one.
    I wrote a script doing that but it is not perfecly stable.
    For my own use, I build an alias of every file to which I want to give an icon. The file itself doesn't keep the icon (and its position in the window) but the alias keep it.
    If you are really bothered by the standard icon, create a subfolder in which you store the documents and use these two scripts.
    --[SCRIPT hideIt]
    set leDossier to "Macintosh HD:Users:yvankoenig:Desktop:documents AppleWorks:"
    try
    tell application "Finder" to set name of folder (leDossier & "masqué") to ".masqué"
    end try
    --[/SCRIPT]
    --[SCRIPT unHideIt]
    set leDossier to "Macintosh HD:Users:yvankoenig:Desktop:documents AppleWorks:"
    try
    tell application "Finder" to set name of folder (leDossier & ".masqué") to "masqué"
    end try
    --[/SCRIPT]
    You will see the aliases with their icon and the true file will be safe in the hidden subFolder.
    Yvan KOENIG (from FRANCE dimanche 10 septembre 2006 20:44:29)

  • HT5137 Words with Friends has frozen. After double clicking the home button, swiping or pressing the icon does not bring up the minus sign.

    On my IPad Words With Friends has frozen. I have double clicked on the home button and identified the WWF icon. When I press and hold or swipe vertically the icon darkens but does not shake or bring up the minus sign. Any suggestions?

    Force close apps
    1. Double tap the home button to bring up the multi-tasking view
    2. Swipe the app's windows upwards to close
    3. The app will fly off the screen
    http://support.apple.com/kb/ht5137

Maybe you are looking for

  • ITunes will not download on Windows 8.1

    I have a new HP Touchsmart 15 with Windows 8.1.   I am trying to download the latest version of ITunes. (having no ITunes on this laptop at all).  Pop up blocker is off.   When I click the download button, absolutely nothing happens.  Thanks for any

  • Why does playback on the timeline lag on my premiere elements 9 project?

    Whenever I playback my edit on the timeline, it starts off playing fine, but after a few seconds it starts to lag. I am using a macbook pro (2.4GHz intel core 2 duo processor, OS X V10.9.4), and was initially editing off a WD hard drive connected wit

  • Exit button code not working in FireFox

    Hi, I am writing a code on exit button , but it is working in IE but not in FireFox--- code is : import flash.external.ExternalInterface; ExternalInterface.call("window.close",""); Also I tried this: var urlString:String = "javascript:window.close();

  • Correct video File Format ?

    I have a mixture of video files - mp4 and m4v. Which is the correct format to play on an iTouch?

  • How to get hostname of a remote computer by ip

    how to get hostname of a remote computer by ip