NBMA and Hello Message

Hi,
In NBMA (non-broadcast multiple access), this communications protocol have no ability for send broadcast or multicast. How it is establish connection with neighbor because (Hello Message) send as multicast.
BR,
Auos.

Hello Auos,
for example for FR by using frame-relay map command with the broadcast option.
FR or ATM NBMA needs to create a copy of each broadcast/multicast packet for each active PVC DLCI.
OSPF has also network types that don't use at all multicast hellos but in this case neighbor commands are needed in the OSPF process.
Hope to help
Giuseppe

Similar Messages

  • ASA Active/Standby mode and Hello messages

    Hi Everyone,
    On ASA  Active/Standby mode  i know thatsay inside or any other interface of active and standby ASA should connect to same switch and vlan.
    When we assign say ip address to inside interface of both ASA like
    ip address 192.168.x.1 255.255.255.0 standby 192.168.x.2 255.255.255.0
    Need to know if these inside interface talk to each other or not?
    Do they send hello messages?
    Thanks
    MAhesh

    Hi Mahesh,
    The ASA Active/Standby Failover pair uses both the dedicated Failover interface and the actual Data interfaces to monitor the "health" of the Failover pair.
    The units send Failover hello messages and wait for a reply to determine if the other unit is alive or not.
    By default all Physical interfaces are automatically monitored. To my understanding Logical interfaces such as Trunk interfaces are NOT monitored by default. You will have to configure monitoring for each subinterface of the Trunk that you want to be monitored.
    You would use the command
    monitor-interface
    Check the Command Reference section for this
    http://www.cisco.com/en/US/docs/security/asa/asa84/command/reference/m.html#wp2123112
    I would also suggest reading the following section of the Configuration Guide
    http://www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/ha_overview.html#wp1079010
    It has information of the Unit and Interface health monitoring of the Failover pair.
    If you want to debug Failover activity you could use the command
    debug fover
    It has multiple additional parameter after that command
    Here is the Command Reference section for the debug command
    http://www.cisco.com/en/US/docs/security/asa/asa84/command/reference/d1.html#wp2093011
    You can even attach a computer on the switch between the ASAs and capture the packets between them an you can see the Failover messages etc from the ASAs
    - Jouni

  • Hello everyone, I have a problem when I sync my apple device. I plug it in and a message comes up saying, this device could not be synced because this computer is not authorized for the purchased items on this phone. I already tried to authorize again.

    Hello everyone, I have a problem when I sync my apple device. I plug it in and a message comes up saying, this device could not be synced because this computer is not authorized for the purchased items on this phone. I already tried to authorize again, after deautherizing it. HELP ME PLEASE

    Hi applerinneedforhelp,
    Thanks for visiting Apple Support Communities.
    If iTunes is asking you to authorize the computer, and you've already done so, the troubleshooting steps in this article can help:
    iTunes repeatedly prompts to authorize computer to play iTunes Store purchases
    http://support.apple.com/kb/ts1389
    Regards,
    Jeremy

  • How can I control the list of cipher suites offered in the SSL Client Hello message? I want to forbid MD5 and RC4.

    How can I control the list of cipher suites offered in the SSL Client Hello message?
    I want to limit my browser to negotiating strong cipher suites. I'd like to forbid DES, MD5 and RC4.

    Set the related SSL3 prefs to false on the about:config page (Filter: security.ssl3.).
    *http://kb.mozillazine.org/about:config

  • Receiving calls and text messages but it wont make tjem

    hello, my iPhone 4 is receiving calls and text messages but it wont make them , it was fine few moments ago , i have tried hard rest , sim removal, resetting network settings , but nothing is happening !

    Hey G.Alby,
    Thanks for using Apple Support Communities.
    There are some steps in both of these article you can still try to resolve these issues.
    iPhone: Troubleshooting issues making or receiving calls
    http://support.apple.com/kb/TS3406
    Ensure that your software is up to date:
    Check for a carrier settings update.
    Check for an iOS software update.
    Note: Some updates may require a Wi-Fi connection.
    If the iPhone has a SIM card, reseat the SIM card.
    iOS: Troubleshooting Messages
    http://support.apple.com/kb/ts2755
    Have a nice day,
    Mario

  • Different alerts for email and sms messages for a contact with custom ring tone

    Hello,
    I have a Curve 8530 with OS 5.0.0.395.
    I have my default sound profile set up to play one type of alert sound when I receive and email message and another when I receive an SMS message (so I know the difference without looking at my phone). That works fine except for contacts that I also have a custom ring tone set up for. It seems that under the Custom Ring Tones/Alerts section of the contact there is only one entry for Messages and it applies to both email and SMS. If I have the contact's message alerts set to the alert I have for email, then their SMS messages play the same alert and I might think it's an email. Or if I have the messages alerts set to the SMS alert sound then their emails sound like SMS messages. Is there a way to have a custom ring tone set up for a contact but still allow their emails and SMS messgaes to follow the current sound profile's settings?
    Thanks.

    Hello,
    Have you had any luck resolving this issue. I had a 8230 and this was possible. But like you I can get the 8530 to work. If you found the solution, please let me know.

  • Just purchased online Adobe Acrobat XI Pro and error message appeared, but payment has been debited from my credit card already

    Hello,
    Just purchased online Adobe Acrobat XI Pro and error message appeared, but payment has been debited from my credit card already and I do not have the software, so paid for nothing.
    I am using a Mac OS X.
    Thanks for your help.
    Ossama

    [discussion moved to Acrobat Installation & Update Issues forum]

  • Touchsmart PC 300-1120 Blue screen and error messages

    My computer turns on and I can access the internet however it will all of sudden kick me off the internet and a blue screen appears that says:  Kernel_data-Inpage-Error and then advises me to remove any new hardware or software.  When I hit enter it goes to a black screen and another message comes up that says Reboot and Select proper boot device but when you hit enter it just repeats and you cannot get out.  Won't even allow me to ctrl-alt-delete to shut down.  Only thing I can do is pull the plug.
    Anybody know what sort of error these could be and what can be wrong?  The only new software is Adobe Reader update and looks like Microsoft updates recently.

    Hello Sydberry,
    Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More. I have read your post on how your computer enters into a blue screen event, and I would be happy to assist you! To begin, I will need to ask you a few questions: 
    What is the Product and Model Number of your desktop computer?
    What version of Windows do you have installed on your computer?
    Has your computer completed all of its important Windows Updates?
    Have you updated your HP drivers using the HP Support Assistant?
    Is this an on-going, or recent issue?
    Is your anti-virus software up to date?
    Is the BIOS on your computer up to date?
    In the meantime, I recommend following this document on BSOD Kernel Data Inpage Error. This should help identify the root of the blue screen event in relation to kernel error.
    Please re-post with the results of your troubleshooting, as well as the requested information above. I look forward to your reply!
    Regards   
    MechPilot
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

  • My IPad shows I have 1.1GB of mail and attachments. What am I not seeing? I have went into each account and deleted messages from all folders (inbox, sent and trash). It still shows that I have that much space used.

    I could really use some help. Probably an easy fix, but I can't seem to figure it ou. 

    Hello Kizzyk,
    I would start with taking a look at the settings to make sure that you are able to send and receive messages. If everything looks good then the next step would be to remove the accounts and add them back in. Take a look at the article below for more information and details on how to troubleshoot your issue further.
    Get help with Mail on iPhone, iPad, and iPod touch
    http://support.apple.com/en-us/TS3899
    Regards,
    -Norm G. 

  • Urgent - Idoc type and the Message type

    Hello
    Its very urgent. I want to know the basic idoc type and the message type used for EDI 894 transmission (Delivery / Return Base Record). Please respond at the earliest.
    Thanks in advance

    HI
    Pratibha
    How are you ?
    Please check the below links:
    http://scn.sap.com/thread/990524
    http://www.erpgreat.com/pm003.htm
    http://scn.sap.com/thread/1386811
    http://scn.sap.com/thread/1078741http://www.erpgreat.com/plant/what-is-equipment-master.htm
    http://benxbrain.com/en/index.do?onInputProcessing%28brai_object_thread%29&001_threadid=0000835100&001_boardtype=01&sysid=PI1&pgmid=R3TR&object=TABL&obj_name=EQBS&child_param=
    Mutti

  • Adobe Digital Edition 4.0 doesn't run and a message appears

    Hello, ADE doesn't open and this message appears. What is the solution or which other software can I use? Thank you.

    note to moderator -   this is MY response to MY own posting.  How can this be a duplicate.
    success.  ADE 4.0 is to be avoided. It crashed after my solution.
    The solution is trash the activation.dat preference file.
    Navigate to /Users//Library/Application Support/Adobe/Digital Editions and drag the activation.dat file to the trash.
    If you are using 10.7, see Access hidden library files | Mac OS 10.7 and later.
    I reinstalled ADE 3.0 and life is good.
    The Error getting License. License Server Communication Problem: E_ACT_NOT_READY

  • Anybody having problems in Mail when sending reply messages from a thread and the message is not showing in the Sent mailbox?

    Hello Folks;
    Got a weird one...
    I am sending replies from a thread in Mail and they seem to have been sent (sounds) but they don't show in the Sent mailbox... O-0 These messages seem to have been delivered to cyberspace as they don't show in my Sent mailbox on my IMAP server... This has been happening for the last month... I have checked and verified all of my IMAP settings and Mailbox behavior settings... This is really weird and maybe a bug.... I checked all of my other clients that have access to the server on the same account and these messages do not show there either.... Any ideas?
    --prd54usa

    The messages are getting to the recipient...
    I am on a Comcast IMAP server if this has anything to do with it and the server settings are following the correct server port numbers, SSL settings, etc... I save Sent messages on the IMAP server for 90 days.... None of these "disappearing" messages were on the server for more than a couple of days.. Typically, these messages will get 'hung' in the Outgoing Mailbox for @30 seconds before sending... like they are being scanned for viruses or Mail can't connect to the server all of a sudden...
    I anybody else here is on a Comcast IMAP server, and having this problem of disappearing Sent messages... This would tell us that it might be a Mail Provider issue with their outgoing server...
    --prd54usa

  • Is it possible to play different sounds for emails and instant messages ?

    Hello,
    I was wondering if it was possible to play different sounds for emails and instant messages. I am using Thunderbird quite often with both emails and instant messages imported from Gtalk.
    I think it would be very convenient to be able to distinguish both sounds as they do not imply the same things.
    Thank you very much.
    Olivier Hubert.

    There are only six chat add-ons, three of them are about notifications. Pick one you think will do the job for you. https://addons.mozilla.org/en-US/thunderbird/extensions/chat/?sort=popular

  • Best way to view iPhone sms and imessage messages from backup

    Hello I have sms and imessage messages that I would like to export from my phone or computer to be viewed on another device.  I know there is a way to view texts through third party software and I was wondering if there is one that is  particularly good at it or if there was a native way to do it?  Any help would be much appreciated as these texts will be used as evidence in a court case so some kind a log format with timestamps would be ideal.

    I actually purchased GoodReader because it is easy to transfer files without iTunes.  I dislike the file sharing through iTunes.   You can use a Mac or PC.  Once I was in the app I clicked the "Wi-Fi" symbol which brings me to "WiFi-transfer."  It will show this --
    "WiFi status: ON
    Use one of the following addresses exactly as you see them
    1. IP-address: http://192.168.0.98:8080 <-- Local LAN address the iPhone is broadcasting on.
    2. Bonjour-address http://Myname-iPhone.local:8080"
    All you have to do is type one of those addresses into your browser. (Safari, etc.)
    It will take you to a page that has iPhone Connection and a list of options.  You can either create a new directory within the application or use an existing one to upload a text file.  It's rather simple, you just select "Choose a file to upload" > Select your file > Press upload > Start the app and see your text/pdf/whatever file.
    You can also connect to a server to download a text file, browse the web, or enter a url.  I see it also has an ICloud folder which I'm not sure if it integrates with Apple's iCloud or not, I think it does.  I'm not affliated with the app and I'm not saying you have to buy it, I'm just a happy user.
    If you don't want to buy this app let me know I'll keep looking for a free or cheaper one for you if you want.

  • ON-ERROR and ON-MESSAGE

    Is anyone using a stored procedure to trap and intercept Oracle Forms Errors and Messages using the ON-ERROR and ON-MESSAGE Triggers?
    In order to do this, I would like to store Oracle's Forms error in a table. I have been unable to located the .msg file that contains the flat file for all of oracle errors and messages. I have loaced the binaries at: $ORACLE_FORMS_HOME\forms90 in the following 5 files: (1) fmcus.msb (2) fmdus.msb (3) fmfus.msg (4) fmgus.msg and (5) fmmus.msb
    Does any know where I can locate the .msg files?
    Any help would be appreciated.

    Hello,
    You can use ERROR_TYPE and ERROR_CODE to ask your own tables
    Declare
    err_code NUMBER := ERROR_CODE;
    errmsg VARCHAR2(512) ;
    Begin
    If ERROR_TYPE = 'FRM' Then
    SELECT message_text
    INTO errmsg
    FROM forms_message_table
    WHERE code = err_code ;
    Elsif ERROR_TYPE = 'ORA' Then
    SELECT message_text
    INTO errmsg
    FROM database_message_table
    WHERE code = err_code ;
    Else
    errmsg := ERROR_TEXT ;
    End if ;
    Set_Alert_Property( 'ALERT1', TITLE, 'Forms error message' ) ;
    Set_Alert_Property( 'ALERT1', ALERT_MESSAGE_TEXTE, errmsg ) ;
    Ok := Show_Alert( 'ALERT1' ) ;
    Exception
    When NO_DATA_FOUND Then
    Set_Alert_Property( 'ALERT1', TITLE, 'Forms error message' ) ;
    Set_Alert_Property( 'ALERT1', ALERT_MESSAGE_TEXTE, ERROR_TEXT ) ;
    Ok := Show_Alert( 'ALERT1' ) ;
    End ;

Maybe you are looking for

  • Problem in query writting , Need a help on priority

    Hi there, Please check the following scenario there are 2 tables event - eventId , userId and eventDate impression - impressionId,userId After joining - userId | impressionId | eventId | eventDate 1 | 1 | null | null 1 | 2 | null | null 1 | 3 | 1 | 2

  • Sort option in Repetitive Area on AR Invoice PLD is disabled / greyed out

    Hi Experts, I have an issue whereby in my PLD the sort option under Print Layout Design Manager -> Repetitive Area -> Sort is greyed out / disabled in the AR Invoice PLD. Does anyone know why this might be? I've not seen this before and I can't find

  • Cost center assessment

    Gurus, please clariffy.. Urgent When I am creating assessment cycles, if I add ( in segments) senders are Cost elements and cost centers together what is going to happen? How the cost is going to be distributed? After running assessments, how do I ch

  • Photoshop license for personal use

    Hello, i'd like to know wether it was forbidden to use Photoshop without paying that much, for a personal use (or in extension until where is it considered illegal, for example for an association poster, for just the family) is it linked to profit or

  • Zen Micro Audio Jack Probl

    Second time it happens to me, the audio jack loosens itself and audio quality goes down the toilet and the sound starts to distort and stuff. on top of that the alarm function is screwed up. I have it set to off during the weekdna nd suddenly it turn