NCS not re-discovering WLC

NCS 1.1.1.24 (PRIME-NCS-VAPL)
5508-50 WLC 7.0.235.3
I had to re-IP this WLC onto another management vlan. Prior to the IP change and code upgrade I removed the WLC from NCS.
When attempting to re-add the WLC to NCS, I finally found the it in Configure>Unknown Devices. Now NCS is showing the Device Type as Unknown, and Inventory Status Detail as Unsupported device, and reachable.
What am I missing???
Thanks!

Yeah... I dot know why it's like that but removing the WLC and adding it back using snmp v2 or v3 fixes the issue but then I have some WLC using v2 and others using v3:)
Sent from Cisco Technical Support iPhone App

Similar Messages

LAP cannot discover WLC after static IP set

I have an 1131 LAP that I originally configured with DHCP and it found the WLC fine. Then I forced the LAP to a static address from the WLC manager. Upon rebooting the LAP it could not find the WLC since it no longer uses DHCP and for some reason it did not retain the WLC IP address in its config. (WLC is on remote subnet and I see LAP sending broadcast to local subnet only in sniffer) 1) How can I reset the LAP to use DHCP - is there a reset button on it? 2) is there some way to have a LAP falback to DHCP discover if the IP is set static?

Hi Armonk,
Have you tried this method?
Clearing Manually Entered Controller Information
When you move your access point to a different location in your network, you must clear the manually entered controller information to allow your access point to associate with a different controller.
Note This command requires the controller configured Enable password to enter the CLI EXEC mode.
To clear or remove the manually entered controller information, you can use these EXEC mode CLI commands:
clear lwapp ap ip address
clear lwapp ip default-gateway
clear lwapp controller ip address
clear lwapp ap hostname
Manually Resetting the Access Point to Defaults
You can manually reset your access point to default settings using this EXEC mode CLI command:
Note This command requires the controller configured Enable password to enter the CLI EXEC mode.
clear lwapp private-config
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/products_installation_guide_chapter09186a0080799c1e.html#wp1061775
Hope this helps!
Rob

Capped zones not getting discovered automatically after global zone discovr

On solaris 10.
We have global zones with capped and uncapped zones.
Zones which are uncapped getting discovered under global zone.
But zones which are capped are not getting discovered.
As per all documents:http://docs.oracle.com/cd/E27363_01/doc.121/e27511/ftr_zones_mgmt.htm
All the non-global zones in the selected global zone are automatically discovered
Edited by: vtadmin on Aug 25, 2012 9:46 PM

The most common reason this usually occurs is because the of the shared memory issue with the Sun MC database. Looks like this issue has been passed on to 4.0. Please try doing the following:
When installing a Server in a whole-root Zone, edit /etc/project to set the shared memory setting first.
Change the "default:3:::" entry to look like this:
default:3::::project.max-shm-memory=(privileged,1073741824,deny)
...where 1073741824 indicates a 1GB setting (you may tune it lower). For more details, go here:
http://docs.sun.com/app/docs/doc/819-5418/6n7gk6ilo?a=view
Mostly this is a problem in whole root zones, but sometimes also applies to the global zones.

AP not joining to WLC

Hi,
After a wireless network interruption, one of MAP 1522 it's not joining to WLC .
What should I do to solve this problem?
Thanks.
(Cisco Controller) >show ap join stats detailed 00:08:30:bb:53:20
Discovery phase statistics
- Discovery requests received.............................. 7
- Successful discovery responses sent...................... 5
- Unsuccessful discovery request processing................ 0
- Reason for last unsuccessful discovery attempt........... Not applicable
- Time at last successful discovery attempt................ Feb 23 11:25:16.137
- Time at last unsuccessful discovery attempt.............. Not applicable
Join phase statistics
- Join requests received................................... 2
- Successful join responses sent........................... 2
- Unsuccessful join request processing..................... 2
- Reason for last unsuccessful join attempt................ RADIUS authorization is pending for the AP
- Time at last successful join attempt..................... Feb 23 11:25:28.385
- Time at last unsuccessful join attempt................... Feb 23 11:25:28.386
Configuration phase statistics
- Configuration requests received.......................... 3
- Successful configuration responses sent.................. 1
- Unsuccessful configuration request processing............ 0
- Reason for last unsuccessful configuration attempt....... Not applicable
- Time at last successful configuration attempt............ Feb 23 11:25:28.581
--More-- or (q)uit
- Time at last unsuccessful configuration attempt.......... Not applicable
Last AP message decryption failure details
- Reason for last message decryption failure............... Not applicable
Last AP disconnect details
- Reason for last AP connection failure.................... Timed out while waiting for ECHO repsonse from the AP
- Last AP disconnect reason................................ AP's capwap state machine restarted
Last join error summary
- Type of error that occurred last......................... AP got or has been disconnected
- Reason for error that occurred last...................... Timed out while waiting for ECHO repsonse from the AP
- Time at which the last join error occurred............... Mar 18 19:07:28.864
AP disconnect details
- Reason for last AP connection failure.................... Timed out while waiting for ECHO repsonse from the AP

Ioan,
as you see here:
Reason for last unsuccessful join attempt................ RADIUS authorization is pending for the AP
It seems you need to add a mac filter for this AP on you WLC so it joins.
Or, if you are using external radius for authorization, you need to add an entery for this AP on the radius server.
Here are some links that may help:
http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a00808f8599.shtml#p5
http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a00808c7234.shtml
Don't please forget to rate the reply if it is useful.
Cheers,
Amjad

WLAN override option not available for WLC 4402 - 6.0.196.

Hi All,
Its kind of weird BUT it seems that the option for WLAN override is missing.u.
I could find it on the lower version BUT not on the 6.0.196.
Please help.
Does this mean I could only set it up via the WCS and not the WLC directly.
Thank you.
Warmest Regards,
Azzafir Ariff Patel.

Hi Scott,
Thank you so much for the clarification.
Thanks again.
Quoting fella5 :
azzafir,
>
A new message was posted in the Discussion thread "WLAN override
option not available for WLC 4402 - 6.0.196.":
>
https://supportforums.cisco.com/message/3042635#3042635
>
Author : Scott Fella
Email : [email protected]
Profile : https://supportforums.cisco.com/people/fella5
>
Message:

Exchange 2010 MP - CAS servers not beeing discovered

Hi!
I have 2 CAS-servers that are not beeing discovered. Trigger on Demand discovery against these servers fails. Is there a way I can manually force these servers to this role?
Best regards
Rune Haugen

Hi,
Have you checked the option "Allow this agent to act as a proxy and discover managed objects on other computers" for all your Exchange servers?
Please also try to flush health service state and caches for the CAS servers.
More details about flush health service state and caches, please refer to the link below:
http://technet.microsoft.com/en-us/library/hh212884.aspx
Regards
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Cisco Prime collaboration provisioning NCS not installed

Hi,
I have installed cisco prime collaboration provisioning which came bundled with BE6k, I am not able to access the web interface, when I ran the
show application status NCS cmd, it says application NCS not installed.
how can I install NCS, so far I am not able to find a way to install it.
please help.
thanks

You can get info by just searching on cisco.com
http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/collaboration/10-0/provisioning/guide/Cisco_Prime_Collaboration_Provisioning_Guide_10/Cisco_Prime_Collaboration_Provisioning_Guide_10_chapter_01110.html

FlexConnect Local Auth. Usernames not showing in WLC/NCS

Hi,
I am working on a new install where the customer is using local RADIUS servers at each of their many campuses
(for local dynamic VLAN assignment), while using a single set of controllers at the core of their network.
For the record, we have set up a pair of 5508s (v 7.2.103.0) in their central data center with 3602i APs around the various campuses. We are using FlexConnect groups to locally authenticate and switch the users.
Right now, the config is working great as far as authentication and local switching goes. The problem we are experiencing is that none of the authenticated usernames are being passed back to the controller (and ultimately NCS). This makes the tracking and troubleshooting of users difficult. Is there something I am missing here? I can't seem to find any fixes relevant to this issue in the 7.2.110.0 release notes.
Maybe I am going about this wrong. I am very open to alternative solutions.
Thanks.

After discussing this issue with local Cisco folks, TAC and colleagues, it seems that locally authenticated user names are not passed to the controller (or NCS). It's not a bug, it's just the way it is.
If you want the AP to authenticate and locally switch users while communication to the controller is down (i.e. loss of WAN link), no usernames are sent to the controller for logging or troubleshooting... even when AP to WLC communication is working fine. It's a trade-off of information (usernames) for uptime.
If any Cisco wireless development folks are browsing, consider this a 'feature' I would like to see. Thanks.

NCS 1.1.3.2 not compatible with WLC Code 7.6 ?

Hello,
i have updatet my WLC 2504 Controllers. I want to applie a new wlan template. But I get only the error message:
"Reason: SNMP operation to Device failed: "
The SNMP Reason is empty....(See attachment)
I work with "Cisco Prime Network Control System". Is this out of date?
I have seen the Version of "Cisco Prime Infrastructe" is newer from date?
Can anyone help me?

Unfortunately, there is no update for the PI 2.1? The month is already around. Any news on this?
On the Cisco Wireless Solutions Software Compatibility Matrix show that PI 2.1 is not compatible with 7.6.x.x ?

Cisco AIR-LAP1041N-E-K9 not working with WLC 4402 version 7.0.116.0

Hi All,
appreciate your support for a problem i started facing today. i have a Cisco WLC 4402 running version 7.0.116.0 and it is working great with 25 Cisco 1252 APs. we have recieved a new 20 Cisco 1041N APs today and i installed one in our site but it doesn't work. it worked fine and loaded the image from flash and got the WLC ip address through DHCP option and started showing the below error:
*Mar 1 00:00:10.021: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:10.033: *** CRASH_LOG = YES
*Mar 1 00:00:10.333: Port 1 is not presentSecurity Core found.
Base Ethernet MAC address: C8:9C:1D:53:57:5E
*Mar 1 00:00:11.373: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:11.465: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1088 messages)
*Mar 1 00:00:11.494: status of voice_diag_test from WLC is false
*Mar 1 00:00:12.526: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:13.594: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:13.647: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1040 Software (C1140-K9W8-M), Version 12.4(23c)JA2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 13-Apr-11 12:50 by prod_rel_team
*Mar 1 00:00:13.647: %SNMP-5-COLDSTART: SNMP agent on host APc89c.1d53.575e is undergoing a cold start
*Mar 1 00:08:59.062: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:08:59.062: bsnInitRcbSlot: slot 1 has NO radio
*Mar 1 00:08:59.138: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:08:59.837: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:09:00.145: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:09:09.136: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 172.16.26.81, mask 255.255.255.0, hostname APc89c.1d53.575e
*Mar 1 00:09:17.912: %PARSER-4-BADCFG: Unexpected end of configuration file.
*Mar 1 00:09:17.912: status of voice_diag_test from WLC is false
*Mar 1 00:09:17.984: Logging LWAPP message to 255.255.255.255.
*Mar 1 00:09:19.865: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:09:19.886: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:09:20.873: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:09:20.874: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
Translating "CISCO-CAPWAP-CONTROLLER.atheertele.com"...domain server (172.16.40.240)
*Mar 1 00:09:29.029: %CAPWAP-5-DHCP_OPTION_43: Controller address 172.16.100.102 obtained through DHCP
*May 25 08:27:02.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:02.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:03.175: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:03.177: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:03.177: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:03.329: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:03.333: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:03.333: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:03.333: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:03.378: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:03.378: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:03.378: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:03.448: status of voice_diag_test from WLC is false
*May 25 08:27:14.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:14.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:15.185: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:15.186: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:15.186: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:15.330: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:15.333: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:15.334: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:15.334: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:15.379: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:15.379: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:15.379: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:15.450: status of voice_diag_test from WLC is false
*May 25 08:27:26.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:26.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:27.182: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:27.183: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:27.184: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:27.329: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:27.333: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:27.333: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:27.333: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:27.377: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:27.377: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:27.377: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:27.433: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*May 25 08:27:27.446: %PARSER-4-BADCFG: Unexpected end of configuration file.
*May 25 08:27:27.447: status of voice_diag_test from WLC is false
*May 25 08:27:27.448: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*May 25 08:27:27.456: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*May 25 08:27:38.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:38.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:39.183: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:39.184: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:39.184: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:39.326: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:39.329: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:39.329: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:39.330: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:39.375: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:39.375: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:39.375: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:39.446: status of voice_diag_test from WLC is false
*May 25 08:27:49.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:49.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*May 25 08:27:50.179: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.100.101 peer_port: 5246
*May 25 08:27:50.180: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.100.101
*May 25 08:27:50.180: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*May 25 08:27:50.323: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*May 25 08:27:50.326: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.100.101
*May 25 08:27:50.326: %DTLS-5-PEER_DISCONNECT: Peer 172.16.100.101 has closed connection.
*May 25 08:27:50.326: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.100.101:5246
*May 25 08:27:50.370: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:50.370: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*May 25 08:27:50.370: bsnInitRcbSlot: slot 1 has NO radio
*May 25 08:27:50.425: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*May 25 08:27:50.438: %PARSER-4-BADCFG: Unexpected end of configuration file.
i searched for the regulatory domains difference between AIR-LAP1041N-E-K9 and AIR-LAP1041N-A-K9 and didn't find any difference that may affect the operation of this AP.
just to mention that our configuration in WLC for regulatory domains is:
Configured Country Code(s) AR
Regulatory Domain 802.11a: -A
802.11bg: -A
My question is, should i only include my country in the WLC (IQ) to add the requlatry domain (-E) to solve this problem? or changing the country will affect the operation of all working APs??
Appreciate your kind support,
Wisam Q.

Hi Ramon,
thank you for the reply but as shown in the below link:
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn7.0.html#wp233793
the WLC in version 7.0.116.0 supports Cisco 1040 seiries APs.
Thanks,
Wisam Q.

AIR-CAP1602I-E-K9 Not Talking to WLC 5508

hi all,
can't seem to get my APs to talk to WLC 5508.
can someone advise which WLC firmware to use and where can i get/download (link pls).
currently WLC is running 6.0.199.4.
Mar 1 00:00:47.839: %CDP_PD-4-POWER_OK: All radios disabled - NEGOTIATED inlin
e power source
*Mar 1 00:00:53.931: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:00:55.963: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP addre
ss 172.28.159.15, mask 255.255.255.192, hostname APfc99.47a3.4d22
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:01:06.899: %CAPWAP-3-ERRORLOG: Did not get log server settings from D
HCP.
*Mar 1 00:01:15.899: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
LER
*Mar 1 00:01:15.899: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_f8
:72:64'running version 6.0.199.4 is rejected.    <<<<
APfc99.47a3.4d22>sh ve
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:52 by prod_rel_team
ROM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFT
WARE (fc1)
APfc99.47a3.4d22 uptime is 11 minutes
System returned to ROM by power-on
System image file is "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1602I-E-K9    (PowerPC) processor (revision B0) with 98294K/32768K
bytes of memory.
Processor board ID FGL1726W6DQ
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.4.1.37
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: FC:99:47:A3:4D:22
Part Number                          : 73-14671-04
PCA Assembly Number                  : 000-00000-00
PCA Revision Number                  :
PCB Serial Number                    : FOC17182J4J
Top Assembly Part Number             : 800-38552-01
Top Assembly Serial Number           : FGL1726W6DQ
Top Revision Number                  : A0
Product/Model Number                 : AIR-CAP1602I-E-K9
Configuration register is 0xF

Hi,
Date and time is ok on the WLC,
I configured Accept Self Signed Certificate (SSC) under Security / AP policy, once done the WLC recognized the AP, but output from the console of the AP power cycle the access point is:
IOS Bootloader - Starting system.
FLASH CHIP: Micronix MX25L256_35F
Xmodem file system is available.
flashfs[0]: 5 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31936000
flashfs[0]: Bytes used: 6551040
flashfs[0]: Bytes available: 25384960
flashfs[0]: flashfs fsck took 9 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: 4c:00:82:9a:47:a3
************* loopback_mode = 0
Loading "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx"...####################
File "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx" uncompressed and installed, entr
y point: 0x100000
executing...
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:52 by prod_rel_team
Initializing flashfs...
FLASH CHIP: Micronix MX25L256_35F
flashfs[2]: 5 files, 2 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 31808000
flashfs[2]: Bytes used: 6551040
flashfs[2]: Bytes available: 25256960
flashfs[2]: flashfs fsck took 9 seconds.
flashfs[2]: Initialization complete.
flashfs[3]: 0 files, 1 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 11999232
flashfs[3]: Bytes used: 1024
flashfs[3]: Bytes available: 11998208
flashfs[3]: flashfs fsck took 1 seconds.
flashfs[3]: Initialization complete....done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
memory validate-checksum 30
^
% Invalid input detected at '^' marker.
no ip http server
       ^
% Invalid input detected at '^' marker.
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
login authentication default
^
% Invalid input detected at '^' marker.
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Warning: the compile-time code checksum does not appear to be present.
cisco AIR-CAP1602I-N-K9    (PowerPC) processor (revision B0) with 98294K/32768K
bytes of memory.
Processor board ID FGL1730S57A
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.4.1.37
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 4C:00:82:9A:47:A3
Part Number                          : 73-14671-04
PCA Assembly Number                  : 000-00000-00
PCA Revision Number                  :
PCB Serial Number                    : FOC17284HL9
Top Assembly Part Number             : 800-38552-01
Top Assembly Serial Number           : FGL1730S57A
Top Revision Number                  : A0
Product/Model Number                 : AIR-CAP1602I-N-K9
% Please define a domain-name first.
logging facility kern
        ^
% Invalid input detected at '^' marker.
logging trap emergencies
        ^
% Invalid input detected at '^' marker.
Press RETURN to get started!
*Mar 1 00:00:12.451: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Mar 1 00:00:13.683: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state
to up
*Mar 1 00:00:14.687: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 00:00:15.123: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:52 by prod_rel_team
*Mar 1 00:00:15.151: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Mar 1 00:00:15.151: %CAPWAP-3-ERRORLOG: Failed to load configuration from flas
h. Resetting to default config
*Mar 1 00:00:16.195: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, chan
ged state to uplwapp_crypto_init: MIC Present and Parsed Successfully
no bridge-group 1 source-learning
                   ^
% Invalid input detected at '^' marker.
%Default route without gateway, if not a point-to-point interface, may impact pe
rformance
*Mar 1 00:00:48.695: %CDP_PD-4-POWER_OK: All radios disabled - INJECTOR_CONFIGU
RED_ON_SOURCE inline power source
*Mar 1 00:00:48.923: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP addre
ss 10.2.3.100, mask 255.255.255.0, hostname AP4c00.829a.47a3
Translating "CISCO-CAPWAP-CONTROLLER.campeche.ecosur.mx"...domain server (10.2.3
.10) [OK]
*Mar 1 00:00:59.915: %CAPWAP-3-ERRORLOG: Did not get log server settings from D
HCP.
*Mar 1 00:00:59.919: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is
not established. A0203E6, 147E, A020364, A47B, 0
*Mar 1 00:01:09.915: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan 29 09:33:18.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 10.2.3.230 peer_port: 5246
*Jan 29 09:33:18.535: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 10.2.3.230 peer_port: 5246
*Jan 29 09:33:18.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
*Jan 29 09:33:23.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
logging facility kern
        ^
% Invalid input detected at '^' marker.
logging trap emergencies
        ^
% Invalid input detected at '^' marker.
*Jan 29 09:34:17.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.
2.3.230:5246
*Jan 29 09:34:17.999: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led sta
te 255
*Jan 29 09:34:17.999: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 29 09:34:17.999: %CAPWAP-3-ERRORLOG: Failed to load configuration from flas
h. Resetting to default config
*Jan 29 09:34:28.015: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan 29 09:34:28.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 10.2.3.230 peer_port: 5246
*Jan 29 09:34:28.535: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 10.2.3.230 peer_port: 5246
*Jan 29 09:34:28.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
*Jan 29 09:34:33.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
and debug command output enable CAPWAP events
(Cisco Controller) >debug capwap events enable
(Cisco Controller) >*spamApTask7: Jan 29 03:39:08.092: acDtlsPlumbControlPlaneKeys: lrad:10.2.3.100(42107) mwar:10.2.3.230(5246)
*spamApTask7: Jan 29 03:39:08.093: 4c:00:82:9a:47:a0 DTLS keys for Control Plane deleted successfully for AP 10.2.3.100
*spamApTask7: Jan 29 03:39:08.100: 4c:00:82:9a:47:a0 DTLS connection closed event receivedserver (10.2.3.230/5246) client (10.2.3.100/42107)
*spamApTask7: Jan 29 03:39:08.100: 4c:00:82:9a:47:a0 Entry exists for AP (10.2.3.100/42107)
*spamApTask7: Jan 29 03:39:08.100: 4c:00:82:9a:47:a0 No AP entry exist in temporary database for 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.104: 4c:00:82:9a:47:a0 Discovery Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.104: 4c:00:82:9a:47:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 500, joined Aps =0
*spamApTask7: Jan 29 03:39:08.104: apModel:
*spamApTask7: Jan 29 03:39:08.104: apType = 38 apModel:
*spamApTask0: Jan 29 03:39:08.105: 4c:00:82:9a:47:a3 Received LWAPP DISCOVERY REQUEST to 6c:41:6a:5f:95:2f on port '13'
*spamApTask0: Jan 29 03:39:08.105: 4c:00:82:9a:47:a3 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100 port 42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 500, joined Aps =0
*spamApTask7: Jan 29 03:39:08.105: apModel:
*spamApTask7: Jan 29 03:39:08.105: apType = 38 apModel:
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100 port 42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 500, joined Aps =0
*spamApTask7: Jan 29 03:39:08.105: apModel:
*spamApTask7: Jan 29 03:39:08.105: apType = 38 apModel:
*spamApTask7: Jan 29 03:39:08.106: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100 port 42107
(Cisco Controller) >*spamApTask7: Jan 29 03:39:08.106: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:18.104: 4c:00:82:9a:47:a3 DTLS connection not found, creating new connection for 10:2:3:100 (42107) 10:2:3:230 (5246)
*spamApTask7: Jan 29 03:39:18.638: acDtlsPlumbControlPlaneKeys: lrad:10.2.3.100(42107) mwar:10.2.3.230(5246)
*spamApTask7: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 Allocated index from main list, Index: 397
*spamApTask7: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 Using CipherSuite AES128-SHA
*spamApTask7: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 DTLS keys for Control Plane are plumbed successfully for AP 10.2.3.100. Index 398
*spamApTask6: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 DTLS Session established server (10.2.3.230:5246), client (10.2.3.100:42107)
*spamApTask6: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 Starting wait join timer for AP: 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:23.636: 4c:00:82:9a:47:a0 Join Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:23.636: 4c:00:82:9a:47:a3 Deleting AP entry 10.2.3.100:42107 from temporary database.
*spamApTask7: Jan 29 03:39:23.637: 4c:00:82:9a:47:a0 MIC AP is not allowed to join by config
*spamApTask7: Jan 29 03:39:23.637: 4c:00:82:9a:47:a0 Join Request failed!

Cisco APs not updating after WLC-update

Hello everyone,
I need to update my 5508 WLCs to a newer software, to support new AP-models.
Started with AIR-CT5500-K9-1-7-0-0-FUS.aes and AIR-CT5500-K9-7-0-240-0.aes, everything worked fine. Pre-Downloaded the newer Image to the APs, restarted the WLCs and everything was ok.
Now I tried to update to 7.6.100.0 as well as 7.4.121.0. Both Versions should support my APs, but it doesn't work at all.
Any ideas are highly appreciated.
If you need further output, just let me know.
Regards,
Manuel
These are some informations about the environment, AP-info and logging after "upgrade" to 7.4.121.0, controller-information after downgrading again...
AP# sh ver
Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(23c)JA7, RELEASE SOFTWARE (fc1)
ROM: Bootstrap program is C1240 boot loader BOOTLDR: C1240 Boot Loader (C1240-BOOT-M) Version 12.4(13d)JA, RELEASE SOFTWARE (fc2)
AP uptime is 1 minute System returned to ROM by power-on System image file is "flash:/c1240-k9w8-mx.124-23c.JA7/c1240-k9w8-mx.124-23c.JA7"
cisco AIR-LAP1242AG-E-K9 (PowerPCElvis) processor (revision A0) with 27638K/5120K bytes of memory.
Processor board ID FCZ1545812F
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on LWAPP image version 7.0.240.0
1 FastEthernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 70:CA:9B:07:86:B8
Part Number                          : 73-10256-07
PCA Assembly Number                  : 800-26918-06
PCA Revision Number                  : A0
PCB Serial Number                    : FOC15402NP4
Top Assembly Part Number            : 800-29152-03
Top Assembly Serial Number          : FCZ1545812F
Top Revision Number                  : A0
Product/Model Number                : AIR-LAP1242AG-E-K9
Configuration register is 0xF
AP#dir
Directory of flash:/
2 -rwx      89311 Jan 18 2014 20:41:00 +00:00 event.log
3 drwx          64 Jan 18 2014 20:43:21 +00:00 update
5 drwx        256 Jan 18 2014 20:40:55 +00:00 c1240-k9w8-mx.124-23c.JA7
4 -rwx        6168 Nov 2 2011 23:32:18 +00:00 private-multiple-fs
7 -rwx        395 Mar 1 2002 00:00:05 +00:00 env_vars
15740928 bytes total (8772096 bytes free)
AP#dir
Directory of flash:/c1240-k9w8-mx.124-23c.JA7/
9 -rwx      131328 Jan 18 2014 20:39:46 +00:00 7101.img
10 -rwx        292 Jan 18 2014 20:39:46 +00:00 info
11 -rwx    4642714 Jan 18 2014 20:40:55 +00:00 c1240-k9w8-mx.124-23c.JA7
15 -rwx      131328 Jan 18 2014 20:40:56 +00:00 6701.img
#sh logging --> see attached file
CONTROLLER (unfortunately after downgrading it again):
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.240.0
Bootloader Version............................... 1.0.16
Field Recovery Image Version..................... 7.0.112.21
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... WLC-IP
Last Reset....................................... Software reset
System Up Time................................... 0 days 0 hrs 26 mins 3 secs
System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin, Rome, Vienna Current Boot
License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... DE - Germany
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 2
Number of Active Clients......................... 5
Burned-in MAC Address............................ 1C:DF:0F:C6:D8:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 150
(Cisco Controller) >show boot
Primary Boot Image............................... 7.4.121.0
Backup Boot Image................................ 7.0.240.0 (default) (active)
(Cisco Controller) >show ap bundle primary
Primary AP Image        Size
ap1g2                  9576
ap3g1                  6684
ap3g2                  11208
ap801                  5192
ap802                  5232
c1100                  3096
c1130                  4972
c1140                  4992
c1200                  3364
c1240                  4812
c1250                  5512
c1310                  3136
c1520                  6412
c3201                  4324
c602i                  3716
(Cisco Controller) >show ap bundle secondary
Secondary AP Image      Size
ap3g1                  6684
ap801                  5192
ap802                  5232
c1100                  3096
c1130                  4972
c1140                  4992
c1200                  3364
c1240                  4812
c1250                  5512
c1310                  3136
c1520                  6412
c3201                  4324
c602i                  3716
Nachricht geändert durch Manuel Sporleder

Hi Scott,
I am not trying to pre-download it anymore, since this doesn't work at all.
If I just restart the controller, the APs are downloading the image telling me "everything is fine", are rebooted and that stated with the old image again.
This is what you can see in the attached log-file:
*Mar 1 00:00:05.873: soap_prepare_new_image_crash: mini ios flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx
*Mar 1 00:00:06.242: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.662: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:09.054: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:09.152: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1024 messages)
*Mar 1 00:00:09.181: status of voice_diag_test from WLC is false
*Mar 1 00:00:11.381: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:11.440: %SYS-5-RESTART: System restarted
*Mar 1 00:00:11.441: %SNMP-5-COLDSTART: SNMP agent on host AP is undergoing a cold start
*Nov 2 23:31:59.107: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Nov 2 23:31:59.108: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Nov 2 23:31:59.929: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Nov 2 23:32:00.107: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Nov 2 23:32:00.107: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Nov 2 23:32:18.102: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Nov 2 23:32:18.163: bsnUnlockDevice: not bring radio up: radio 1 is in admin disable state
*Nov 2 23:32:18.345: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Nov 2 23:32:18.759: status of voice_diag_test from WLC is false
*Nov 2 23:32:18.847: Logging LWAPP message to 255.255.255.255.
*Nov 2 23:32:33.181: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Nov 2 23:32:33.247: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Nov 2 23:32:34.212: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Nov 2 23:32:34.213: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
*Jan 20 20:32:44.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: WLC-1-IP peer_port: 5246
*Jan 20 20:32:44.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Jan 20 20:32:45.479: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: WLC-1-IP peer_port: 5246
*Jan 20 20:32:45.480: %CAPWAP-5-SENDJOIN: sending Join Request to WLC-1-IP
*Jan 20 20:32:45.481: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Jan 20 20:32:45.483: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Jan 20 20:32:45.483: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Jan 20 20:32:45.483: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Jan 20 20:32:45.484: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from WLC-1-IPperform archive download capwap:/c1240 tar file
*Jan 20 20:32:45.494: %CAPWAP-5-AP_IMG_DWNLD: Required image not found on AP. Downloading image from Controller.
*Jan 20 20:32:45.499: %CAPWAP-5-CHANGED: CAPWAP changed state to IMAGE
*Jan 20 20:33:58.755: %DTLS-3-BAD_RECORD: Erroneous record received from WLC-1-IP: Duplicate (replayed) record
*Jan 20 20:33:59.315: image upgrade successfully, system is now reloading
This happens again and again and again...
Regards, Manuel

AP 1042N with ios 15.2(4)JB5 is not joining to WLC with ios 7.4.121.0

I am trying to add AP 1042N with ios15.2(4)JB5 in WLC 2504 with IOS version 7.4.121.0 , but AP is not joining and
Below mentioned is the log I am getting in the AP , here 192.168.100.10 is WLC ip
*May 20 19:31:22.745: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*May 20 19:51:24.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.100.10 peer_port: 5246
*May 20 19:51:24.804: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.100.10 peer_port: 5246
*May 20 19:51:24.805: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.100.10
*May 20 19:51:29.804: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.100.10
*May 20 19:52:23.222: %DTLS-5-ALERT: Received WARNING : Close notify alert from 192.168.100.10
*May 20 19:52:23.222: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.100.10:5246
*May 20 19:52:23.223: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*May 20 19:51:24.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.100.10 peer_port: 5246
*May 20 19:51:24.818: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.100.10 peer_port: 5246
*May 20 19:51:24.819: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.100.10
*May 20 19:51:29.819: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.100.10
Can anyone tell me, is there any issue between the AP & WLC IOS compatibility or what else could be reason for this.

Hi Thanks for everyone's comments,
I found solution, I i was extracting only one file from the tar image and supporting files were not extracted to flash
Now I did " “archive tar /xtract tftp://<TFTP server IP>/<ImageName>.tar flash: “ and extracted complete tar in to the flash and changed boot priority. Now it is joining to controller
Thank you

Server 2012 R2 Hyper-v Servers not being discovered by the mp

Sorry if this is a dup question. I did see the one for 2008 but that didn't fix my issue.
I have 4 hyper-v servers running server 2012 r2 in a cluster. I have scom 2012 r2 and it detects the cluster and 3 out of the 4 hyper-v servers. the 4th server it can see under windows but does not discover the hyper-v components.
Any assistance would be appreciated.

Hi,
You can install the Agent on the server manually to check the result.
http://technet.microsoft.com/en-us/library/hh212853.aspx
Niki Han
TechNet Community Support

Redundancy not forming with wlc

Hi,
We have two wlc 5508 running vers 7.4.100.60. They are not forming redundancy pair & are in maintenance mode.
Both RP's are connected physically direct.
Few outputs are given here:-
(WLC01) >show redundancy summary
Redundancy Mode = SSO ENABLED
     Local State = MAINTENANCE
      Peer State = UNKNOWN - Communication Down
            Unit = Primary
         Unit ID = 2C:11:5A:5F:C7:00
Redundancy State = Non Redundant
    Mobility MAC = 2C:11:5A:5F:C7:00
Maintenance Mode = Enabled
Maintenance cause= Negotiation Timeout
Redundancy Management IP Address................. 10.32.25.11
Peer Redundancy Management IP Address............ 10.32.25.12
Redundancy Port IP Address....................... 169.254.25.11
Peer Redundancy Port IP Address.................. 169.254.25.12
(WLC02) >show redundancy summary
Redundancy Mode = SSO ENABLED
     Local State = MAINTENANCE
      Peer State = UNKNOWN - Communication Down
            Unit = Secondary - HA SKU
         Unit ID = 10:B3:21:3C:01:B0
Redundancy State = Non Redundant
    Mobility MAC = 10:B3:21:3C:01:B0
Maintenance Mode = Enabled
Maintenance cause= Incompatible Software license
Redundancy Management IP Address................. 10.32.25.12
Peer Redundancy Management IP Address............ 10.32.25.11
Redundancy Port IP Address....................... 169.254.25.12
Peer Redundancy Port IP Address.................. 169.254.25.11
(WLC01) >show license summary
License Store: Primary License Storage
StoreIndex: 0 Feature: base                              Version: 1.0
        License Type: Permanent
        License State: Active, Not in Use
        License Count: Non-Counted
        License Priority: Medium
License Store: Evaluation License Storage
StoreIndex: 0 Feature: base-ap-count                     Version: 1.0
        License Type: Evaluation
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8 weeks 4 days
            Evaluation period left: 8 weeks 4 days
        License Count: 500 / 0 (Active/In-use)
        License Priority: None
(WLC02) >show license summary
License Store: Primary License Storage
StoreIndex: 0 Feature: base                              Version: 1.0
        License Type: Permanent
        License State: Active, Not in Use
        License Count: Non-Counted
        License Priority: Medium
License Store: Evaluation License Storage
StoreIndex: 0 Feature: base-ap-count                     Version: 1.0
        License Type: Evaluation
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8 weeks 4 days
            Evaluation period left: 8 weeks 4 days
        License Count: 500 / 0 (Active/In-use)
        License Priority: None
In addition, other errors are also seen during the process.
Starting Redundancy: Starting Peer Search Timer of 120 seconds
Cannot open the file /mnt/application/ha/InheritedApCount.txt
Cannot open the file /mnt/application/ha/InheritedApCount.txt
Please help with all possible suggestions. thanks in advance

Hi,
i cant see that you have permenant AP count license on both.
review the following document for licensing requirement on AP SSO
http://www.cisco.com/en/US/products/ps10315/products_tech_note09186a0080bd3504.shtml#licensing

NCS not re-discovering WLC

Similar Messages

Maybe you are looking for