NCS Prime Wireless Management

Hello,
We have recently purchased Cisco NCS Prime for our Cisco Wireless project. Before installation we need to confirm that NCS
prime will be compatible with ESXi v5.0, as the release notes refer to
ESXi v4.0 and v4.1 only.
http://www.cisco.com/en/US/customer/docs/wireless/ncs/1.0/release/notes/
NCS_RN1.0.1.html
Many thanks
Jonathan.

Hi Chris,
1. No.
2. There is a symptom of the following bug:
CSCtw52442 NCS: Lobby Ambassador user can access the home page.
Installing Chrome frame plugin for IE browser in NCS is a requirement as documented in the release notes. This caveat is to address the issue where lobby ambassador users are getting access to the NCS home page to which they have no privileges for. For your IE users, install chrome frame plugin which should take care of it.
Ram.

Similar Messages

NCS Prime Wireless

Hi
I am running a NCS Prime Wireless 1.1.24 ... and i have the following questions/problems..
1. Can we change the Font Size on the printout of the guest data generatet via NCS??
2. If i login simultan with two same usernames (lobby ambassador) i see a different Homepage ..
With firefox it works as designed, if i login via IE9 with the same username simultan i get the starthomepage of the NCS without the config buttons...
Anybody the same problems ??
Thanks Chris

Hi Chris,
1. No.
2. There is a symptom of the following bug:
CSCtw52442 NCS: Lobby Ambassador user can access the home page.
Installing Chrome frame plugin for IE browser in NCS is a requirement as documented in the release notes. This caveat is to address the issue where lobby ambassador users are getting access to the NCS home page to which they have no privileges for. For your IE users, install chrome frame plugin which should take care of it.
Ram.

Unable to Push the Config Frm NCS prime to CIsco WIreless Lan Controller

Hi Guys,
We have an issue with NCS prime, in our Network.
We run NCS prime 1.3 and Around 10 Wireless Lan Controllers (5508 & 4404) Models.
We are trying to Push a ACL Config Template from NCS to Wireless lan Controllers.
This ACL is already created before in WLCs, now we created the templates in NCS with few rules added and planning to push Configs from NCS template.
We are receiving errors SNMP operation to device failed. I am pretty sure it is not an SNMP issue.
Any inputs on this is much appreciated

Hi Scott.
I
I tried deleting the ACL from Controller totally and tried pushing it. it was not working neither
Raised a case with Cisco. They asked for few trace logs from NCS , told will check and get back to me.
IS there any more inputs, you can provide, which i can try to test it?
Regards
Safwan

Recomended report to identify inactive Netuser accounts on NCS prime 1.3

hi
i have two 5508 running 7.4 being monitored by NCS prime 1.3
Using local net users created origionally on the wlc but now from prime.
we are looking for a report that will show inactive users to assist with housekeeping.
rgds
Graham

Hi,
You can get the pur grp description by the table T024.
In SAP the release will be effected by relese code, which will not be assigned to the user.But however you can find who released from the table CDHDR by providing the transaction code in the field ME52N.
Regards,

CAnnot connect to wireless manager

Have attempted to connect to wireless amnager several times, enter "admin" as both login and pw but system keeps looping back to that same screen.
Trying to connect blackberry with wireless capability to home system. Tried the button method but that did not work, now trying to enter pin into wireless manager but can't get into internet address.

What is the model no of the Router...?
Are you trying to open the setup page of the router...?
if you are trying to open the router setup page then,use the password "admin" in lower case.Do not type anything in the username...If that does not work then,reset the router for 30 seconds and try again ...

Cisco Prime Performance Manager 1.6: Install Units silently ? ./setup.sh -f silent_input_file.txt

Friends
This one should be routed to Cisco prime performance manager 1.6 forums
I am seeking a sample silent input format for silently installing Cisco PPM 1.6 Units by executing ./setup.sh -f <silent_input_file.txt>
Any help in this regards is greatly appreciated.
Thanks in advance
Dharmesh Shah
###### Excerpts from setup.sh ########
# Install a fresh copy of unit
InstallUnit () {
if [ "$INSTALLFILE" != "" ] ; then
./setupSvr.sh -f $INSTALLFILE -i unit
else
./setupSvr.sh $NOPROMPT -i unit
fi
if [ $? = 2 ] ; then
finish
exit
fi

Friends
This one should be routed to Cisco prime performance manager 1.6 forums
I am seeking a sample silent input format for silently installing Cisco PPM 1.6 Units by executing ./setup.sh -f <silent_input_file.txt>
Any help in this regards is greatly appreciated.
Thanks in advance
Dharmesh Shah
###### Excerpts from setup.sh ########
# Install a fresh copy of unit
InstallUnit () {
if [ "$INSTALLFILE" != "" ] ; then
./setupSvr.sh -f $INSTALLFILE -i unit
else
./setupSvr.sh $NOPROMPT -i unit
fi
if [ $? = 2 ] ; then
finish
exit
fi

Cisco NCS Prime - Possible Database Issue?!

Hello;
I appear to have problems with our NCS Prime database, I am running NCS in HA environment and over the last few months been running on the secondary server and collecting reports fine.
After failing back I have noticed that no data appears when I run reports on have a "flat-line" on all reports which gather data such as Client Traffic, once I failed back again to run on the secondary server in an attempt to gather some data the same problem occurs. I do however seem to have a small peak in data last night for 4 hours but this then dropped off.
Is there any way to see if I have lost the historical data?
Thanks
John

Issues I have seen is from upgrading. Have you upgraded to PI 1.3 or was PI 1.3 a greasy install? Also they might have some commands that they will have you issue or they will issue, but it's better for them to give you those than telling you what to issue because you don't want to loose everything.
Sent from Cisco Technical Support iPhone App

How to Re-Install Cisco NCS Prime in vmware appliance?

I'm attempting to do an Eval on NCS to see if it's worth pursuing this year or wait until next budget year and I'm having quite a bit of trouble, which is pushing me towards the "this sucks" category. My initial setup of NCS Prime went by with out a hitch until the NCS service tried to start and threw what looked like and Oracle DB error. Not being able to figure out how to re-install from the vmware appliance it's self, I had to kill the appliance and redo. This time, after asking me the typical and simple question of ip address and etc, it hung on trying to complete the setup of the app and ate up 16gig on my vmware box. Now, I realize that there is a maintenance release available as of last Friday, but my question is, instead of having to redo the enter appliance, how can I force the appliance to attempt a re-installation of NCS so that hopefully I can get to the point where I just do the maintenance upgrade? I would figure there would have be some way to re-install NCS in the vmware appliance with out re-installing the entire appliance in a support scenerio correct?
-Raun

If you mount the DVD image for the Vmware appliance so that it boots "on the dvd", you would have the option to reimage. No need to "recreate" the whole setup then.
Normally once it's installed, the upgrades don't require to re-image but you seem to be having troubles. The problem with Vmware installation is that it's hard to evaluate if the problem comes from the NCS or from the vm setup itself.

NCS Prime prompting for login and password after re-imaging from dvd

Dear All,
I did a re-imaging on NCS prime after which I'm getting the below error
Please help me as to what could be the reason for this error...
Please type 'setup' to configure the appliance
localhost.localdomain login: Setup
Password:
Regards,
Waseq Mohammed

Re-imaging was not successful try this process:
Restoring the NCS Database
If you are restoring the NCS database in a high availability environment, see the "Restoring the NCS Database in a High Availability Environment" section. To restore the NCS database from a backup file. follow these steps:
Step 1 To view all local repository backups, use the below command:
show repository backup_repo
Note If possible, stop all NCS user interfaces to stabilize the database.
Step 2 Manually shutdown the platform as root.
Step 3 Using the CLI, perform one of the following:
•Restore the appliance and application backup by entering the following command:
restore testbackup-yymmdd-xxxx.tar.gpg repository backup_repo
•Restore only the application backup by entering the following command:
restore testbackup-yymmdd-xxxx.tar.gpg repository backup_repo application NCS
Step 4 Click Yes if a message appears indicating that NCS is running and needs to be shut down.
Note If the restore process shuts down NCS, a restart is attempted after a successful restore. The appliance will then restart and you will have to again login and restart the dbserver, and the platform manually as root (make sure you do not start with dbclean, else you will loose your recently restored data).
The CLI displays messages indicating that the NCS database is being restored.

Cisco Prime Assurance Manager

Is Cisco Prime Assurance Manager included in Prime Infrastructure ...I know it is going EOS.

NO, Cisco Prime Assurance Manager is upgraded and replaced by Cisco Prime Infrastructure. Refer the notice :
http://www.cisco.com/c/en/us/products/cloud-systems-management/prime-assurance-manager/index.html

NCS Prime 1.0 Eval License

I'm trying to get/install the 10 device eval license on a new NCS Prime 1.0 virtual appliance. I downloaded what I thought was the the right eval license but get this error when installing.
udi of file does not match the system
All I can find in the licensing guide is is this:
Cisco Prime NCS Evaluation Licenses
Cisco Prime NCS can be used in a lab or in an evaluation setting with the following license: NCS-10-DEMO. This provides an evaluation license for 10 devices, for a duration of 30 days. If you need a custom device count or duration, please contact your Cisco representative.
Can someone point me in the right direction?
--Patrick

I got it up and running this way :
1. Downloaded the NCS-VA-1.0.1.4-small.ova from cisco.com
2. Got it up and running on VmWare, run the guided setup..
3. Logged into the Gui
4. In the "License Center" you can see "product id" and "serial number" of the virtual appliance.
5. Used the "product id" and "serial number" to request a demo license on : cisco.com/go/license - "Demo and Evaluation Licenses" - NCS Demo 1.0 -
6. Download it and add it in license center
Now you have a 100 device license for 30 days
Carsten

Prime Infrastructure Manager 1.2 and Apple IPad

Is there a way to run Prime Infrastructure Manager on an IPad?

You can download the utility to run the cisco Prime
https://itunes.apple.com/us/app/cisco-prime/id556600515?mt=8
and other app created by cisco the may be helpful
http://www.cisco.com/web/about/facts_info/apps/ciscoapp.html?CAMPAIGN=tomorrowstartshere&COUNTRY_SITE=us&POSITION=vanity&REFERRING_SITE=vanity&CREATIVE=vanity+to+mobile+app

Latest Toshiba 3G drivers & Wireless Manager don't work in Windows 7?

Hi all,
I've installed, uninstalled, and re-installed the latest Toshiba 3G drivers and Toshiba Wireless Manager software for my NB200-123 netbook, and they don't appear to work in Windows 7.
When I start the Toshiba Wireless Manager software now (version 6.3.1.101), it starts for a split second, then Windows 7 immediately pops up a dialog box saying:
"Wireless Manager has stopped working"
(I used to have the older XP drivers partly working, though they had the problem that if you hibernated the netbook, the next time you opened the Toshiba Wireless Manager software, it would freeze at the point where it said, "opening driver", and it would never come back)
I've currently got the following versions:
Toshiba F3507g Mobile Broadband Device - (from Toshiba) version 4.54.7103.1, dated 26/6/2009
Toshiba F3507g Mobile Broadband Network Adapter - (from Ericsson) version 1.0.0.52, dated 29/7/2009
Has anyone else managed to get this working on their NB200-123 with Windows 7? I'm wondering if I have a bad driver version somewhere?
I can't imagine that Toshiba would have rolled this out without testing it, so I must have something misconfigured somewhere.
Best
Rob

Ok, this does appear to be related to some kind of failed access to a .NET library. Whenever I try to launch any of the Toshiba applications, it fails immediately, and I get the following Application Event error in the event log. Note that the reference is to CLR20r3, which has to do with .NET I understand. mscorlib, referenced below, is definitely a .NET library.
Now, I know that this is supposed to be running on .NET 3.5 sp1, but I'm on Windows 7, and that includes .NET 3.5 sp1, and furthermore I've run tests on the OS to determine the .NET version(s) installed, and I've definitely got .NET 3.5 sp1 installed. So why am I getting this error?
Fault bucket , type 0
Event Name: CLR20r3
Response: Not available
Cab Id: 0
Problem signature:
P1: wirelessmanager.exe
P2: 6.1.3.1
P3: 4a895b6e
P4: mscorlib
P5: 2.0.0.0
P6: 4a275af7
P7: f50
P8: 7
P9: N3CTRYE2KN3C34SGL4ZQYRBFTE4M13NB
P10:
Attached files:
C:\Users\rob.DESKTOP\AppData\Local\Temp\WER429D.tm p.WERInternalMetadata.xml
These files may be available here:
C:\Users\rob.DESKTOP\AppData\Local\Microsoft\Windo ws\WER\ReportArchive\AppCrash_wirelessmanager._f99 9ba902d33835d8a9c2164386cf138c110bc_14ae60f6
Analysis symbol:
Rechecking for solution: 0
Report Id: 557e9845-06bc-11df-82ad-db865f2b48b5
Report Status: 65

Need wireless manager of sonyericsson MD300 for windows 7

hello,
has spent several days looking for the wireless manager soy Ericsson MD300 for windows 7 64bit
I searched everywhere on the internet but I did not find anything ...
I even saw the following discussion:http://talk.sonymobile.com/message/20065#20065
but the download link that is shown is no longer available ....
Thank you for helping me to find
Solved!
Go to Solution.

First check if there's an operator logo on the MD300. If so you should contact that operator for software and drivers. A branded MD300 may have a different firmware and may not work with our Wireless Manager.
Regarding Wireless Manager we don't have any version compatible with Windows 7. It only supports Windows 2000/XP/Vista. If you have an unbranded MD300 and want to test it anyway, please let me know and i'll send you the software.
- Official Sony Xperia Support Staff
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page.

NCS Prime 2.1 Percentage of Licenses used on WLC2504

Is there an exportable report that can be run on NCS Prime Infra 2.1 that will provide an AP count percentage of licenses used for each controller?
Attached is a screen shot of a visual of what I want in an exportable excel file for WLCs.

Thank you, however, I need to export information that will tell me the percentage of licenses used of the total by each WLC.
I have many hundreds of WLCs and need a spreadsheet that will tell me how many licenses each individual WLC has and what percentage each WLC is using of their total.

NCS Prime Wireless Management

Similar Messages

Maybe you are looking for