NDIS drivers for Hyper-V Legacy Network Adapter

I would like to load NDIS driver for my MS-DOS boot disk in a Hyper-V virtual machine using the legacy network adapter.
Long story short, I'm trying to revive an old MOC (Microsoft Official Curriculum) course and the only resource I have available to me is Hyper-V.
Thanks.

Hi,
The legacy network adapter emulates a physical network adapter, multiport DEC 21140 10/100TX 100 MB.
so look for that one
http://www.intel.com/design/network/drivers/nd2_300.htm
good luck

Similar Messages

Windows Server 2008 Standard Drivers for Intel I217LM Gigabit Network adapter

Hi everybody,
I am unable to find Network drivers for Intel® I217LM Gigabit Network adapter for Windows Server 2008 Standard (32-bit). I have found the drivers for Windows Server 2008 R2 but that being 64-bit do not work.Kindly help me in sorting out this problem as I
am stuck need to install the drivers.
Thanks in advance.
SHOAIB

Please post your question in Intel forums : https://communities.intel.com/community/tech/places
Arnav Sharma | http://arnavsharma.net/ Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading
the thread.

Windows 8.1 Enterprise - Hyper-v, Legacy Network Adapter works, but the Network Adapter does not

Folks,
I currently have 2 Virtual Switches: one I set up for WIFI, and the other I set up for
LAN.
Both switches are set up as:
- EXTERNAL
- Allow management operating system to share this network adapter
Both switches I can use with my Legacy Network Adapter.
But the Network Adapter doesn't doesn't work for either.
It did however work at one time, but I think a Windows Update killed it.
Thoughts? Suggestions?
And as always, thank you for reading :)

And here's my HYPER-V log, Running Windows 7 Pro:
(I've applied an 'xxx' info related to my company.)
Windows IP Configuration
   Host Name . . . . . . . . . . . . : broberts-e6420
   Primary Dns Suffix . . . . . . . : xxx.com
   Node Type . . . . . . . . . . . . : Hybrid
   IP Routing Enabled. . . . . . . . : No
   WINS Proxy Enabled. . . . . . . . : No
   DNS Suffix Search List. . . . . . : xxx.com
                                       attlocal.net
Ethernet adapter Local Area Connection 2:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . : attlocal.net
   Description . . . . . . . . . . . : Intel 21140-Based PCI Fast Ethernet Adapter (Emulated)
   Physical Address. . . . . . . . . : 00-15-5D-01-4C-08
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
Ethernet adapter Local Area Connection 1:
   Connection-specific DNS Suffix . : attlocal.net
   Description . . . . . . . . . . . : Microsoft Hyper-V Network Adapter
   Physical Address. . . . . . . . . : 00-15-5D-01-4C-06
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   IPv6 Address. . . . . . . . . . . : 2602:306:3a5e:7050:7426:4a85:cde9:3454(Preferred)
   Temporary IPv6 Address. . . . . . : 2602:306:3a5e:7050:2d15:806e:7f3b:ca31(Preferred)
   Link-local IPv6 Address . . . . . : fe80::7426:4a85:cde9:3454%20(Preferred)
   IPv4 Address. . . . . . . . . . . : 192.168.1.65(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Lease Obtained. . . . . . . . . . : Monday, July 28, 2014 10:18:19 PM
   Lease Expires . . . . . . . . . . : Tuesday, July 29, 2014 10:18:20 PM
   Default Gateway . . . . . . . . . : fe80::769d:dcff:fe77:2379%20
                                       192.168.1.254
   DHCP Server . . . . . . . . . . . : 192.168.1.254
   DNS Servers . . . . . . . . . . . : 192.168.1.254
   NetBIOS over Tcpip. . . . . . . . : Enabled
Tunnel adapter isatap.attlocal.net:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . : attlocal.net
   Description . . . . . . . . . . . : Microsoft ISATAP Adapter
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 11:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Microsoft 6to4 Adapter
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Teredo Tunneling Pseudo-Interface:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes

Drivers for the sunfire v20z network card.

does any one know were i could find the drivers for the sunfire v20z network card. and does anyone know the chipset of the card?

That's a software question.
This is a hardware forum.
You didn't specify, but I'll presume you are not talking about any add-on card.
The necessary software packages for the onboard
broadcom BCM5703 gigabit (bge) circuitry are native to Solaris x86 (4/04 and newer).
Therefore they'll be on your OS installation CD's.
Just install the OS and rock-n-roll.

Assign management ip address with SCVMM 2012 R2 for hyper-v converged network?

Hi,
I am setting up a converged network for our Hyper-V clusters using vNICs for the different network traffic including management, live migration, cluster-csv, hyper-v etc.
Problem is, how do I assign the hyper-v hosts a management IP address? They need a network connection on the management network for scvmm to manage them in the first place. How do I take the existing management IP address that is directly assigned to the
host and transfer it directly to the new vNIC so scvmm has management of it? Kind of in a chicken and egg situation here. I thought about assigning a temp ip address to the host initially but am worried that assigning the address will cause problems as then
the host would then have 2 default gateways configured. How have others managed this scenario?
Thanks
Microsoft Partner

Rule of thumb: Use one connected network for your Fabric networks (read the whitepaper), and use VLAN based networks for your tenant VMs when you want to associate VM Networks with each VLAN.
-kn
Kristian (Virtualization and some coffee: http://kristiannese.blogspot.com )
We don't have tenants as such due to this being an environment on a private company LAN for sole use of the company virtual machines.
What I have so far:
I created "one connected network" for Hyper-V-Virtual-Machine traffic.
Unchecked "Allow new VM networks created on this logical switch to use network virtualization"
Checked "Create a VM network with the same name to allow vms to access this logical network directly"
This logical network has one site called UK.
Within this site I have defined all of the different VLANS for this site.
Created IP pools for each VLAN subnet range.
I hope I understand this correctly. Started reading the whitepaper from cover to cover now.
Microsoft Partner

New Intel WIFI Wireless Network Adapter does not recognize Wireless Router

I have had a Linksys BEFW11S4 Version 4 Wireless router for quite some time. It works like a champ and I have one Laptop wired to it and a second using Wireless working just fine. Recently, I received a new ThinkPad W500 Laptop with an Intel WIFI Link 5100 AGN wireless network adapter. The older laptop that works just fine with the router uses a
11a/b/g Wireless LAN Mini PCI Express Adapter by Atheros. However, the NEW laptop with the Intel Adapter fails to connect to the Router. It will either indicate a failure while "Waiting for Association" or it will indicate a failure when waiting to "renew IP Address". Sometimes, it will show a signal strength close to ZERO (Even as the older laptop with the other adapter is showing a signal strength close to 100%) When I called Linksys support, I was told that the facts that the Router (a) works find with the wired Laptop and (b) works fine with the 11a/b/g NEtwork Adapter and (c) works fine when WIRED to the new laptop all indicate that the problem is NOT with the router at all -- but with the Network Adapter. Can anyone tell me what has to be adjusted in the Adapter settings? Right now, I am using IBM Access Connections for BOTH of the wireless laptops. I have made sure to set IDENTICAL values for SSID and WEP (128-bit) [static] password. I have also ensured that all OTHER settings are the same for the two laptops. Yet, in one laptop, there is NO PROBLEM while in the other, I can not get the Wireless Adapter to "see" the signal from the Router. TO further check this, I have [temporarily] disabled the WEP password, enabled SSID broadcast, and disabled the MAC address restrictions that I put in (so that the system would be totally "open") yet the Intel Adapter STILL did not "find" anything. In addition, when I use the "Find WIFI" feature in Access Connections, I find that SOMETIMES the network with SSID is found and sometimes, it will display "unknown network" and not pick up the SSID.
This is all very frustrating. If anyone has experience with the Intel WIFI Link 5100 AGN Adapter, I would appreciate any hints, tricks, ideas, etc.
Think you!!!!
--Zvi

I installed the LATEST version of IBM Access Connections as well as verifying that I have teh LATEST drivers for the Intel Wireless NEtwork Adapter.
What now happens is that I am able to authenticate to the Router. However, I get a failure on "renewing IP Address" -- which [according to the diagnostic message] means that the Rotuer fails to provide me with an IP address to use. Do you have any suggestions?

Trying to set-up the network adapter in Solaris 11 under Hyper-V fails

I was using Virtual Box to run Solaris 11 for testing purposes, however VB was disappointing as my VM hanged too often so now I am evaluating Hyper-V under Windows 8 Pro. If I can get the network to work I will use Hyper-V even if it lacks seamless mouse
and keyboard integration. So, I installed Solaris 11 in Hyper-V but I cannot get the network to work. What I have done:
- I have created a Virtual Switch of type External with Virtual Switch Manager
- I have created a Legacy Network Adapter for my virtual solaris machine
- in Windows 8 I have created a Bridge for my WiFI NIC and the Virtual Switch
I can access the internet from my host machine (windows 8)but I cannot do it from the guest (solaris)
If I type "ipadm" in my solaris's terminal I can see that the NIC is listed but it has no IP address. So how can I assign an IP address to the Legacy Network Adapter?
Thanks

Hi Brian,
Thanks for the reply. I have managed to get networking working by creating a legacy card attached to a virtual switch, but I have not used the bridging anymore, instead I simply shared in the host OS the wifi connection to the virtual switch. This way it works.
Now I have another problem with the Solaris guest OS not seeing the SCSI controller, but I'll open a new thread for this after some more testing.
Thank You
Codrut

Hyper-v Client in Win10 Enterprise Technical Preview does not boot to PXE via Leagacy Network Adapter after OS is installed using gen 1 BIOS

Using Hyper-v within Windows 10 Enterprise Technical Preview to boot a Win 7 Legacy BIOS (Generation 1) Operating system client does not boot to PXE legacy network adapter after operating system has been installed within the Virtual Client.
Hyper-v Client will boot to PXE Legacy Network Adapter only when no other boot device is available and no OS is installed.
Hyper-V settings seem to ignore BIOS - Startup order within Hyper-V Client Settings and will always boot to VHD before Legacy Network Adapter even if Legacy Network adapter is first in the startup list.
IF VHD is deleted and a new VHD added to the Client then will boot to PXE using Legacy Network Adapter. Again once OS is installed then will not boot to PXE Legacy Network Adapater.
Gen 2 BIOS/UEFI works as expected and boots to PXE network everytime.

Hi shaunmoncrieff,
Thank you for the information.
Currently I am not available to take a test using Windows 10 on physical machine.
You may try to submit this information through Windows Feedback Tool, once I have tested, I will update the results here.
Best regards
Michael Shao
TechNet Community Support

Migrate Roles failes when migrating VMs with legacy network adapters (2008R2 - 2012)

I'm working on a upgrade of Hyper-V 2008R2 cluster to Hyper-V 2012 cluster. I am using the "migrate roles" feature of failover clustering to migrate the CSV's and VM's. The wizard ask to which switch the VMs need to be connected on the target cluster.
All VMs with network adapters can be started in the new cluster without any issues. If you look at the XML file of the migrated VMs with normal network adapters, a new XML has been generated in the proper 2012 format. However, all VM's with a legacy
network adapter fail to start. Also there is no migrated XML file in the VM directory. It is impossible to check or adjust the settings of the migrated VMs with legacy network adapters using the failover clustering console.
I have reproduced the issue in my lab several times, and it seems like a bug.
There are several workarounds, but I am looking for a real solution.

Hi,
We recommend that you use the legacy network adapter only to perform a network-based installation or when the guest operating system does not support the network adapter.
If the virtual machine continues to use the legacy network adapter it will not be able to leverage many of the features available in the Hyper-V virtual switch. You may want
to replace the legacy network adapter after the operating system is installed.
The related KB:
Building Your Cloud Infrastructure: Converged Data Center without Dedicated Storage Nodes
http://technet.microsoft.com/en-us/library/hh831829.aspx
Configure Networking
http://technet.microsoft.com/en-us/library/cc770380.aspx
Hope this helps.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Monitor bandwidth utilization for Hyper-V's Virtual Machines

Hi,
I'm wondering, if SCOM is capable to monitor incoming & outgoing traffic (current and total over time) of VMs in Hyper-V?
Tried to search about it, and found only 3rd party tools or the monitoring is only available for Router, not VMs.
Thanks.

Hi Andre,
Also you can use performance monitor to monitor the VM's bandwidth through counter "Bytes Received/sec" and "Bytes Sent/sec" under Hyper-v virtual network adapter :
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Linux drivers for SUN Quad PCI card

Hi everyone.
I have a question regarding drivers for a Sun QUAD network card. I belive it is a X1034A card.
The card is also marked with a label saying: *5015406063174* and a barcode. On another label it says: P04280713
Is there any chance that this card would function under a Linux operating system on an intel x86 server?
Does anyone know where I could find the drivers for this configuration?
Best regards,
Rod

Take a closer look at the actual card,
particularly at the central Ethernet chip.
If I recall correctly, it is a DEC DC2115x chipset for 10/100Mbit connectivity,
and should be natively recognized by Linux.
The 501-5406 QFE card, as shown on a 3rd party web site.
Install it and boot your system.
You should know in just a few moments whether it'll work,
or whether the Sun firmware is of any concern.

Windows drivers for SUN Quad PCI card

Hi everyone.
With the risk of being flamed, I have a question regarding drivers for a Sun QUAD network card. I belive it is a X1034A card.
The card is also marked with a label saying: *5015406096836* and a barcode. On another label it sais: QFEPCI
Is there any chance in h**l that this card would function under a Windows system?
Best regards,
Johan Christensson

Hello Ben,
I own the IntraServer LSI5464E which appears to be 501-5406-01 (using the DC21153-AC which was on my card manufactured by Intel not DEC).
I was wrong, the 21153 is a PCI-to-PCI Bridge chip by Intel. I thought it's similar to the DEC PCI Fast Ethernet DECchip 21140.
The 4 Ethernet controllers chips are manufactured by/for Sun.
The datasheet for the LSI5464E is still available, while the drivers aren't.
Michael
When will the deficencies/bugs in the Forums software be fixed ?

Needed drivers for Windows XP

I just installed Windows XP on my MBP and it's still missing drivers for:
iSight
Ethernet Controller
Network Controller
PCI Device
SM Bus Controller
Video Controller
Can anyone tell me where to find them? I've tried other drivers and they simply do not work....

http://www.apple.com/macosx/bootcamp/
From the Boot Camp Assistant you can burn a drivers CD.

Where to download driver for the SD BT2 Bluetooth adapter for Win7 x64?

Hello,
where can I download drivers for the SD BT2 Bluetooth adapter for Win7 x64?
Thank you.

I agree with bluecat.
BT SD card is not on the market for years now and this device is not supported anymore so I think you will not be able to find driver to get it work with Win7.

Cannot download drivers for my network adapter - Gigabyte X58A-UD5 Motherboard

Hey everyone, I recently got tired of my wireless connection for obvious reasons and decided to run an ethernet cable from my modem to my computer. I once I plugged in the ethernet cable nothing happened; I was confused and checked my network adapters
and my Lan adapter isn't there, no problem I'll just go download the drivers for it. I downloaded DriverTuner from the gigabyte site, and ran it found I didn't have drivers for an "Ethernet Controller" or a "Standard Duel Channel PCI IDE Controller".
So I download and attempt to install the drivers and get the error message "You have to run the 64-bit version of DPInst.exe on this machine - Contact vendor". (That's my problem and question - sorry for the story thought it might help.)
I've tired all number of ways to fix this, including attempts at running DPSisnt.exe, which I have no idea how to run any help would be appreciated, and am I even on the right track? is there something simpler going on?
Thanks :)
Connor

did you try this one?
http://download.gigabyte.us/FileList/Driver/motherboard_driver_lan_realtek_8111_w7.exe
Don
(Please take a moment to "Vote as Helpful" and/or "Mark as Answer", where applicable.
This helps the community, keeps the forums tidy, and recognises useful contributions. Thanks!)

NDIS drivers for Hyper-V Legacy Network Adapter

Similar Messages

Maybe you are looking for