NEED A HELP: problem with setting up AP 1140

Hello everybody,
I did finish all the configuration steps for Cisco Aironet 1140 AP1140 mentioned in the manual and AP start showing green indication:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Set the timeout value on the TFTP server to 30 seconds.
Step 4 On the PC where the TFTP server is located, perform these steps:
a. Disable any software firewall products, such as Windows firewall, ZoneAlarm firewall, McAffee firewall, or others.
b. Ensure all Windows files are visible. From Windows Explorer, click Tools > Folder Options > View; then uncheck the Hide extensions for known file types check box.
Step 5 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, c1240-k9w7-tar.default for a 1240 series access point, and c1250-k9w7-tar.default for a 1250 series access point.
Step 6 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 7 Disconnect power from the access point.
Step 8 Press and hold MODE while you reconnect power to the access point.
Step 9 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 10 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 11 After the access point reboots, reconfigure it using the GUI or the CLI.
BUT (the next step is missing) and the problem is that I cannt access the GUI through browser. Also there is no bytes communicated between my FTPT server and the AP. I am connecting the 48 DC powered AP with default IP 10.0.0.1 directly through Ethernet cable cat6 to the FTPT server with adapter setting is: IP 10.0.0.10 S.mask 255.0.0.0.
I did some trials such as: connecting the AP to DHCP server with PoE switch, change TFTP to dynamic IP, enable/ disable adpter, restart the AP but without any change
What I need to know
Is there any missing steps in the above?
Is the default IP for AP 10.0.0.1?
What to do in this case?
How to access CLI and what are the basic commands for settings?
Thanx a lot waiting the reply plz

hello dear,
yes I pressed at the begining of configuration when i was about to download the IOS, shall i press it again after completion?
yes I have a console port where i can put the RG45- DP 9 cable

Similar Messages

I just bought an AirPort Extreme system over this weekend and I am having problem with setting it up. I plugged the cable as explained in the manual but there is no way I can get a steady green light. I all see is flashing amber light. Can anyone help me,

I just bought an AirPort Extreme system over this weekend and I am having problem with setting it up. I plugged the cable as explained in the manual but there is no way I can get a steady green light. I all see is flashing amber light. Can anyone help me,

Think you need to provide some more details about what you are connecting

Problem with Set/Get volume of input device with single channel

from Symadept <[email protected]>
to Cocoa Developers <[email protected]>,
coreaudio-api <[email protected]>
date Thu, Dec 10, 2009 at 2:45 PM
subject Problem with Set/Get volume of input device with single channel
mailed-by gmail.com
hide details 2:45 PM (2 hours ago)
Hi,
I am trying to Set/Get Volume level of Input device which has only single channel but no master channel, then it fails to retrieve the kAudioDevicePropertyPreferredChannelsForStereo and intermittently kAudioDevicePropertyVolumeScalar for each channel. But this works well for Output device.
So is there any difference in setting/getting the volume of input channels?
I am pasting the downloadable link to sample.
http://www.4shared.com/file/169494513/f53ed27/VolumeManagerTest.html
Thanks in advance.
Regards
Mustafa
Tags: MacOSX, CoreAudio, Objective C.

That works but the the game will not be in full screen, it will have an empty strip at the bottom.
I actually found out what's the problem. I traced the stageWidth and stageHeight during resizing event. I found out that when it first resized, the stage width and height were the size with the notification bar. So when I pass the stage into startling, myStarling = new Starling(Game,stage), the stage is in the wrong size. For some reason, I can only get the correct stage width and height after the third resizing event.
So now I need to restart Starling everytime a resizing event happened. It gives me the right result but I am not sure it is a good idea to do that.
And thanks a lot for your time kglad~I really appriciate your help.

Problem with SET GET parameters

Hi all,
I am facing a problem using SET and GET parameters.
There is a Z transaction(Dialog program) where some fields of screen are having parameter ID's. That transaction is designed to diaplay/change status of only one inspection lot at a time.
Now I need to call that transaction in a loop using BDC. I mean i need to update the status of multiple inspection lots(one after the other). Before calling the transaction I am using
SET PARAMETER ID 'QLS' FIELD lv_prueflos.
Unfortunately the transaction is only changing the first inspection lot. When I debugged I found that the screen field is changing in PAI. Even though in PBO it shows the next value, when it goes to PAI it is automatically changing to the first value(inspection lot).
Example: Inspection Lots : 4100000234
4100000235
4100000236
Now first time when the call transaction is being made the status of insp lot 4100000234 is changed. For the second time when insp lot 4100000235 is being passed in PBO ican see this. But the moment it enters PAI the screen field changes to 4100000234.
Could you pls help me in solving this issue.
Thanks,
Aravind

Hi,
Problem with SET GET parameters
Regarding on your query. Follow this below link.
It will help you.
Re: Problem with Set parameter ID
Re: Problem in Set parameter ID
I Hope it will helps to you.
Regards,
Sekhar

Problem with setting Source Level in Sun Studio 2

I've got problem with setting Source Level to 1.5 in Sun Studio 2. When I try to set it to 1.5 in Project properties and click Ok everything seem to go well, but when I open Project Properties again Source Level is set to 1.4. I need this to work cause I started to lear Java recently and I want to use foreach loop.
Please help

I'm just citing an example using Date().
In fact, whether I use DateFormat or Calendar, it shows the same result.
When I set the date to 1 Jan 1950 0 hours 0 minutes 0 seconds,
jdk1.4.2 will always return me 1 Jan 1950 0 hours 10 minutes 0 seconds.
It works correctly under jdk1.3.1

Problems with setting up my ISP's mail server in Windows Live Mail and Thunderbird

The laptop is a G60-535DX with Windows 7 64 bit. I've managed to setup my gmail account fine in Live Mail, but when setting up my ISP' mail server, it doesn't work. I get the message that the information was entered correctly, and I see the 'connecting' at the bottom of the page, and then 'error', and clicking on it shows a socket error #10061. In Thunderbird, I get a timeout error message. I've entered all the incoming and outgoing server information correctly, (I've done this over 8-9 times now), the ports are the defaults(110,25), no SSL, no authentication. I've talked with my ISP several times. Just a couple of hours ago was the last time. Their only other possibilities were that Live Mail had problems with setting up more than one account, that Live Mail needed updating, that Windows 7 was a new operating system and there were 'kinks'. I removed the gmail account, set up the ISP's mail by itself; didn't help. I checked for Live Mail updates, but found out that they all come from Windows updates(which are current). The folks on PCQ&A inform me that they have 3 or 4 accounts with Live Mail. I can get my mail, by logging onto my ISP's website, but that' kind of a nuisance. I posted this in Seven Forums and they didn't have any ideas. As I said, I also can't get my mail server to work in Thunderbird, either. I don't know what else to try. (short of activating the recovery partition and starting from scratch). Any ideas would be more that welcome.
Thanks,
Steve

Stevehiker wrote:
Nevermind, it's fixed. One of the guys on PCQ&A suggested going to my ISP's website to see if they had a support page. They did and it stated that under certain circumstances that for the login ID the whole email address should be entered. For XP and Outlook Express one only uses the first part of the email address (your name); so just for grins I entered the whole address, name and all and everyting worked. Called my ISP and was told that that wasn't the way it's supposed to work. Well----
Thanks anyway,
Steve
Mine works the same way_must enter full email address as login. AT&T?
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others**

Button in Bex Analyser 7.0 - problem with setting up Static Parameters

Hello,
I know a similar problem has been discussed here already, but I am still having problems with setting up Static Parameters of my Button in BEx Analyser 7.0, so that I can pass Variable values from that button to my query.
This is what I do - in Static Parameters of my Button I set the following values:
Name                          Index          Value
DATA_PROVIDER        0               DP_1
CMD                             0               PROCESS_VARIABLES
SUBCMD                      0               VAR_SUBMIT
VAR_NAME                 0               0RMA_FIP
VAR_VALUE               0               004/2010
As a result, I would like the value 004/2010 to be passed to variable 0RMA_FIP (which is mandatory) and the query to be executed with that value. For some reason, however, the value is not passed correctly, and instead the variable is filled with a blank or not filled at all, and I am getting a message "Specifiy value for variable Fiscal year/period". What do I do wrong?
Just to give you a broader picture - I would like to later use this logic to pass more than one variables into a query, including a hierarchy node, and read the values from an Excel worksheet - however, after many attempts to do so, I started playing with just one variable to figure out what the problem was.
I have already seen the following two threads and SAP notes on passing variable values from the button:
Re: Button in BEx Analyzer 7.0
Re: How to set variables values via VBA.
http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/f0881371-78a1-2910-f0b8-af3e184929be?quicklink=index&overridelayout=true
Can anyone please advise?
Cheers,
AL

I managed to figure it out myself!
Instead of VAR_VALUE I need to enter VAR_VALUE_EXT, and it works fine.
I will mark this thread as "answered".

Problem with setting Item level permissions lists

Hello!
I have SPS 2013 on-premised environment with AD authentication.
At some moment I've noticed that we have a problem with setting the item level permissions on any lists except the document libraries.
When I click the "shared with" button I see a popup form with a list of users who have an access to that list but there is no "invite people" link or "Advanced" link. Moreover, the "loading" ring rotates
instanly like some operation was'nt ended.
The same operation with documents in libraries works well.
I am be grateful for any help!

Hi Mischael,
From your description, my understanding is that there were no "invite people" or "Advanced" link when some users clicked "shared with" button in some lists.
This issue seems like about permissions. Please log on your site with site collection administrator or a user who has full control for the site, then go to a problematic list->List settings->Permissions for this list, check whether the list
has unique permissions. Then click "Check Permissions", check the permission level for the problematic users and then go to Site Settings->Site permissions->Permission levels, check whether the permission level contains "Manage permissions".
If not, add the permission into the permission level.
Thanks,
Wendy
TechNet Community Support
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact
[email protected]

HT4759 I can't update IOS 4.3 to the new IOS 5. Or download the latest verison of I Tunes, on my IPad 2. Because I don't have a computer,but i heard Apple suport can help me with setting it up.

I can't update IOS 4.3 to the new IOS 5. Or download the latest verison of I Tunes, on my IPad 2. Because I don't have a computer,but i heard Apple suport can help me with setting it up.

Scroll down and see the "Update Your Device Using iTunes" section here:
HT4623
There is no "update icon" in iOS versions earlier than iOS 5.
The update is very large (over 1.2 gigabytes). You need a good internet connection to download it to your computer. Maybe you'll need to take a trip to a city to get a good enough connection.

Obiee 11g . problem with set default as columnname in interaction tab

Hi Obiee gurus ,
I have small problem with set default option in interaction tab in column properties. actually my problem is , i changed one column bold save as set default option bold and how to revert back to my column option. when i create new analysis with same name . it takes set default option for that column.
can Please give some suggestion for this problem.
regards
Srinivas

Hi Srinivas,
i guess this will be same for 11G
Refer
http://blogs.oracle.com/siebelessentials//2008/08/remove_systemwide_default_sett.html
thanks,
Saichand.v

Premiere Pro CS5: please help problem with importing a file error output "there was an error decompressing audio or video"

please help problem with importing a file error output "there was an error decompressing audio or video"

this is related to what adobe program/version?

Help please!!! problem with setting up Zen NX (software/driver e

<SPAN class=postbody>Hello, i am new to this forum and have limited knowledge about the Zen NX and would really appreciate any help or advice that you could offer. O.K. i got a Zen NX in Jan 2004, ran the software disc supllied, no problem. I then turned on the player but it was not recognised by the computer ("Device not connected") so i went to the support site and found out that this was a known problem and needed to download a piece of software which i think was named (Drv_JB3.EXE)?. Once this was done i had no problem at all and the player turned out to be a great piece of kit. About two months ago i had to re-set my computer to the factory settings because of a virus, anyway yesterday i decided i would put the software back in for the Zen NX and add some new music. I did everything as before, and luckily i had saved the extra piece of software that was required in order to get the computer to recognise the player. Unfortunately, everytime i tried to download the software it just kept saying that there was a problem with the driver and that i should reconnect the player in order for the software to work, which of course never happened and it just kept on repeating this message everytime i reconnected the player. Anyway i spent the rest of the day uninstalling the main software and reinstalling and then trying the latest drivers downloaded from the creative website and also the latest version of Media Source etc, all to no avail (getting well pi**ed off at this point) i even did a "restore" in XP to see if this would help but no joy. Just to let you know i think that the origional driver version was (.23.00) and the Creative Media Source version was (.0.84). I do not think that there is a problem with the USB port or cable as the computer recognises that a new piece of hardware as been added when i plug in the player.
<SPAN class=postbody>I have posted this message on nomadness.net but as yet i have had no reply<SPAN class=postbody>
Any help or advice would be gratefully appreciated, before i launch the Zen out of the window!!!
<SPAN class=postbody>
cheers, Burni.

Get the following:
. Creative Zen and Jukebox Driver Upgrade version .30.03
2. Creative MediaSource Player/Organizer 3.30.2
3. Creative Zen and NOMAD Jukebox plugin 2.00.9 for Creative MediaSource
Install . then connect the player to the PC. Then install 2. and 3. (the player must be connected for 2. to verify you have a Creative product).

Help Needed in resolving problems with Hyperion Planning Web Forms

Hi,Can anyone help me with this problem?Problem:We are running Planning 2.3.1 I have created Webform & security(application owner has the ownership).Somehow Iam getting only 7 dimensions into webform & 1 dimension is missing in that. But whereas 8 dimensions are there in Essbase.Hsp_Rates dimension is available in essbase outline but Iam unable to see that dimension in the webform selection.And using the webform Iam unable to load any data ...the form is graded/protected.Is this happening because i dont have the requirement of 1 member from each Dimension?Please someone let me know why this is happening what might be the reason.ThanksUser

Hi,The dimension Hsp_Rates is a hide dimension used by Planning to store the exchange rates for the differentes exchanges.All the standard information is stored on HSP_InputValue member (in this dimension).When you create a web form, Planning automatically asign this member (but don't show it).Probably you can't load data because you are selected on Version dimension a Standard Botton Up version, and you only can load data on level 0 members in this type of version.If you want to load data on upper level members, then you need to create a Standard Target version (in the Version dimension) and select it in the form.Please, advice if this solve your problemClaudioBPD Solutions

Need help: Problems with exported Dreamweaver html file in different browsers

I'm trying to send out a newsletter, and had our designer create it in Dreamweaver, and then export and html file which we uploaded. For some reason it looks wrong on Mac's, Gmail, and a few issues with Outlook. Does anyone know how to help with this, or had to work around this problem in the past?
I've attached our html file as well.
We're an eco startup with limited time and budget - so any help you have would be so appreciated.
Thank you!!

      World Centric Monthly Newsletter   August 2009
Palo Alto Joins the Ban Against
         Non-Recyclable Materials
       This Spring, Palo Alto joined the list of more than 30 cities and counties in California who are making good on their efforts toward reducing their greenhouse gas emissions
       by enacting partial or comprehensive bans on polystyrene (PS) foam and/or non-recyclable disposable foodservice containers. Around the same time, a California statewide ban on the use of PS containers was tabled before reaching the State Assembly floor. Representative
       Jerry Hill, one of AB 1358’s sponsors, pulled the bill due
       to concerns addressed in the Appropriations committee hearing of the bill, regarding the fiscal impacts which
       were not addressed in bill’s contents.
       Largely represented by the California Restaurant Association, opponents of AB 1358 lobbied legislative representatives and argued there would be a negative fiscal impact on struggling restaurant owners and their customers in order to accommodate the more expensive alternatives to PS containers.     There are the unquantifiable and “hidden” costs of contaminating our bodies and environment which would far surpass the fiscal impact on the plastics, restaurants and consumer industries. Studies published by the Foundation for Advancements in Science and Education have indicated that varying levels of styrene residues
         are present in 100% of all human fat tissue in the
         United States, as PS products are found to lose weight after in contact with hot or fatty/acidic foods and liquids, causing migration of the styrene into the food or fluid, ending up in the human body. On the high end, the levels were “one third of levels known to cause neurotoxic symptoms”. In the environment,
         PS is rarely recycled and does not biodegrade.     Supporting safer alternatives to polystyrene, in addition to the collection infrastructure and processing mechanisms for the compostable and recyclable products would help create more green jobs in the long run and would be a move in the right direction away from unnecessary harm
       to our health, our communities and our world. Keep your eyes open for a revised version of AB 1358 in Spring 2010!     For more information about polystyrene
       visit Earth Resource.     For a partial energy, emissions and water analysis
       of polystyrene and its alternatives visit our website.           World Centric Compostable
         Hot Cup Lid
         World Centric is pleased to announce we now offer a fully compostable hot cup lid that
         fits our 10oz, 12oz, 16oz,
         and 20oz paper hot cups.
       The lids can be ordered in cases of 1000 or packs of 100.
       For more information or to order, please visit our website.           This Month
         We’d Like to Applaud
       Project Open Hand
       San Francisco's non-profit
       organization that prepares and delivers food to seniors, people living with HIV and homebound critically-ill residents. For nearly 25-years Project Open Hand has been providing “meals with love” to local residents in need of help and care in
       California’s San Francisco and Alameda counties.
       Programs include meals, groceries and nutrition information as well as education and referral programs
       for all of the people served. A staff dietitian also visits several sites per week to speak with seniors and critically ill local residents about the importance of eating well
       and staying healthy.
       Project Open Hand continues to serve nearly 800,000 annually and has served as a model for over 100 organizations across the United States and the world.
       If you are interested in making a donation,
       please visit Project Open Hand.
       Help Project Open Hand continue to do what it
       does best – deliver quality food to those in need.
“World Centric has gone
           about every aspect of
           business in the most
           sustainable of ways.
           It is a model for socially
           responsible business.”
           Ari Patz
           Styrophobia
               Industry Trends
           Although PLA is a sustainable alternative to a petrochemical-
           derived product, its limitation has
           been not only its cost, but its inability
           to maintain structural integrity in hot temperatures and humid conditions because of its low melting pint.
           However, researchers at Teijin
           (formerly in partnership with Cargill)
           have improved their plant-based
           ‘Biofront’ PLA polymer to be able
           to withstand higher temperatures –
           by modifying its hydrolytic resistance.
         Get more information here.
               Get Great Deals!
               Check out our clearence items.
               Did you know?
           Styrene can leach from polystyrene.
           Over the long term, this can act as
           a neurotoxin. Studies on animals
           report harmful effects of styrene
           on red-blood cells, the liver, kidney,
           and stomach organs.
           US Environmental Protection Agency (1992) “Styrene”. Air Toxics Website.
               Where to Find us:
               CRRA Conference
               August 2 - 5
               Palm Desert
                      Western Foodservice
& Hospitality Expo
             August 30 - September 1
          Livable Green
             September 19
San Mateo
   Find us:            World Centric
2121 Staunton Ct. Palo Alto, CA
You are subscribed as <[email protected]>. Click here to manage your email subscription preferences.
Click here or reply to this email with 'unsubscribe' in the subject to unsubscribe from this list or if you feel you have received this message in error.
This message was sent from World Centric 2121 Staunton Ct Palo Alto CA 94306 United States. Click here to report email abuse.
You are subscribed as <[email protected]>. Click here to manage your email subscription preferences.
Click here or reply to this email with 'unsubscribe' in the subject to unsubscribe from this list or if you feel you have received this message in error.
This message was sent from World Centric 2121 Staunton Ct Palo Alto CA 94306 United States. Click here to report email abuse.

I just got my macbook pro 11 have problems with setting up audio interfaces!! plz help me

So here it goes! i properly installed the drivers for my Emu tracker pre usb and for my saffire pro 40 (firewire) . Both audio interfaces show up in the system profiler under their respective category (firewire and usb bus) But i cant get them to apear in system preferences sound menu neither on logic!! my saffire pro doesnt even lock with the mix control software provided! what can be the problem ? how can i solve it ? I really need your help!!
(everything works perfect on my i mac 27" 10.6.2 snow leopard).

I doubt you will have any virus, must never say never
Free for Home use
Sophos
http://www.sophos.com/en-us/products/free-tools/sophos-antivirus-for-mac-home-ed ition.aspx
also free from app store Clam XAV
http://www.usatoday.com/story/tech/columnist/komando/2013/02/14/tech-myths-mac-s oftware-megapixels-camera/1910521/
Your Battery will not last long if you keep it on full brightness.
see this read
https://discussions.apple.com/thread/964075?start=0&tstart=0
http://support.apple.com/kb/PH3738
http://support.apple.com/kb/index?page=search&src=support_site.home.search&local e=en_US&q=Battery%2095%25
Open LaunchPad/Other/Activity Monitor/CPU
and check if any of your processes are high% CPU if so select it and press the Red Quit process Button
Mac101 may assist you
http://www.apple.com/support/macbasics/

NEED A HELP: problem with setting up AP 1140

Similar Messages

Maybe you are looking for