Need a help to config 1841 router!

Hi all,
Could someone tell me,can I configure two ISP on one Fast Ethernet port. We have a client, bougth a 1841 Modular router without aditional WAN cards. So, the router hes only two interfases. In this moment, we use one interfase for internal LAN and other for ISP. But the client want to has second ISP.

Mariya
Whether you can do that depends on some details that you have not given us.
It is possible to configure more than one IP address on a FastEthernet interface using secondary addresses. So you could configure the address used by one ISP as primary and configure the address used by the other ISP as secondary. For this to work both ISP would need to give the client an Ethernet handoff and you would need a small Ethernet switch to connect the router FastEthernet to both ISPs.
HTH
Rick

Similar Messages

Need help regarding Cisco 1841 Router

hello everyone , i am need of help regarding configuring of FE 0/1 port. our company have a cisco 1841 router. The serial 0/0/0 is connected with VSAT for internet. The FE 0/0 is connected to switch(LAN) through which net connectivity is provided to all users. Recently a new VSAT has been installed at our site,with different IP series. So every time we want to switch between the two net connectivity we need to change the entire IP configuration of all users, which in turn prohibits the users from accessing the printers,data servers etc which are been set to our existing IP series. So, my idea was to configure the FE 0/1, so that just by changing the DNS will help us providing internet along with all other devices without changing the entire IP series. The new VSAT modem has a lan cable which can be connected to FE 0/1. Can any one help out in solving the problem. Our existing IP series is 192.168.3.1..... and the new VSAT series is 10.205.74.1......

Bao
Do I understand correctly that you will have 20 remote users who will telnet to the 2511 and from the 2511 will use reverse telnet to access the console of router1, router2, router3, etc which have their console ports connected to async ports of the 2511? If that understanding is correct then the firewall only needs to open TCP port 23 for telnet. The other ports (2001, 2002, etc) are between the 2511 and router1, router2, etc and will not be seen by the firewall. If my understanding is not correct then please clarify.
I do not believe that you will find an image for the 2500 that supports SSH.
HTH
Rick

Need help, VPN between 1841 router & PIX 501

Trying to setup a VPN between an 1841 router at HQ with static IP connecting to remote office with a PIX 501 and a persistent IP (not static, but Mediacom has mapped PIX MAC this IP so I always get same public IP even on equip reboot). I have configured both sides but tunnel will not come up, must be missing something.
See attached configs.
THANK YOU!

Sorry.
interface: outside
Crypto map tag: IPSEC, local addr. 12.206.137.5
local ident (addr/mask/prot/port): (10.5.5.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (10.2.1.0/255.255.255.0/0/0)
current_peer: 216.203.117.82:500
PERMIT, flags={origin_is_acl,}
#pkts encaps: 659, #pkts encrypt: 659, #pkts digest 659
#pkts decaps: 462, #pkts decrypt: 462, #pkts verify 462
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts compr. failed: 0, #pkts decompress failed: 0
#send errors 124, #recv errors 0
local crypto endpt.: 12.206.137.5, remote crypto endpt.: 216.203.117.82
path mtu 1500, ipsec overhead 56, media mtu 1500
current outbound spi: 793ff99e
inbound esp sas:
spi: 0xcbd5b096(3419779222)
transform: esp-des esp-md5-hmac ,
in use settings ={Tunnel, }
slot: 0, conn id: 4, crypto map: IPSEC
IV size: 8 bytes
replay detection support: Y
inbound ah sas:
inbound pcp sas:
outbound esp sas:
spi: 0x793ff99e(2034235806)
transform: esp-des esp-md5-hmac ,
in use settings ={Tunnel, }
slot: 0, conn id: 3, crypto map: IPSEC
sa timing: remaining key lifetime (k/sec): (4607996/1929)
IV size: 8 bytes
replay detection support: Y
outbound ah sas:
local ident (addr/mask/prot/port): (10.5.5.0/255.255.255.0/0/0)
remote ident (addr/mask/prot/port): (216.203.117.85/255.255.255.255/0/0)
current_peer: 216.203.117.82:500
PERMIT, flags={origin_is_acl,}
#pkts encaps: 2691, #pkts encrypt: 2691, #pkts digest 2691
#pkts decaps: 2601, #pkts decrypt: 2601, #pkts verify 2601
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts compr. failed: 0, #pkts decompress failed: 0
#send errors 0, #recv errors 0
local crypto endpt.: 12.206.137.5, remote crypto endpt.: 216.203.117.82
path mtu 1500, ipsec overhead 56, media mtu 1500
current outbound spi: c6d3ea5c
inbound esp sas:
spi: 0x55d659c5(1440111045)
transform: esp-des esp-md5-hmac ,
in use settings ={Tunnel, }
slot: 0, conn id: 1, crypto map: IPSEC
sa timing: remaining key lifetime (k/sec): (4607097/1917)
replay detection support: Y
inbound ah sas:
inbound pcp sas:
outbound esp sas:
spi: 0xc6d3ea5c(3335776860)
transform: esp-des esp-md5-hmac ,
in use settings ={Tunnel, }
slot: 0, conn id: 2, crypto map: IPSEC
sa timing: remaining key lifetime (k/sec): (4607743/1890)
IV size: 8 bytes
replay detection support: Y
outbound ah sas:
outbound pcp sas:

In desperate need of help trying to get router installed

Hi,
I have a macbook and I have just bought a Belkin router and have put the setup disk in the drive. It says to open up the disk and click start.osx.
When I do this it just says 'There is no default application specified to open the document "start.osx"
Then offers me the choice to choose application.
What do I do? Please help me before I lose all my hair!
Thanks

I concur with the previous suggestion. I find the "setup wizards" to be useless at worst or poor at best. I'm thinking the only useful thing on that setup CD is the user manual.
I think Belkin's usual web interface is at http://192.168.2.1:88 . That's what I recall from trying to get one working. Plug it in via the ethernet cable and try accessing the configuration from there. HTTP (web-page style) interfaces work great although sometimes you need to hunt around for all the steps you need. Even someone who uses a setup wizard will need to use the standard web-based configuration screens for more advanced settings and monitoring.

Need huge help on my router WRT120 N thanks

Hi, new here, really needed some help regarding my Linksys router WRT 120 N, which i bought not too long ago. Long story short, had it for ps3 online and it worked terrific, tried to get it too connect with the 360 and a disaster.
My idea was too uninstall anything Linksys has and then reinstall the same router. I figured that way i could go back to the previous settings before i tinkered with them for the 360, and just start fresh with a new SSID and have an easier time that way. So i tried, a number of times, but everytime i do, it says the program/router is already installed, leaving me with little to no idea what to do to get it back to workign with the ps3, let alone ever trying for the 360.
By the way, as you may tell, im pretty much tech illiterate, didnt grow up around it and now that i have it, it confuses me quite alot. I feel most comfortable just figuring out how to uninstall it, that is my preference, but if some one knows how i can fix it without doing that and getting my 360 and ps3 online with it, would also appreciate that. I migth not understand lingo, but im very driven to get this over with, i have been pulling my hair out for hours trying with my very limited knowledge.
Again, any help and all help is so so very appreciated, thank you so much in advance.
If you need any other information, please dont hesistate to ask me.

Before using the setup program again, you will need to reset your router to factory defaults.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is likely dead. Report back with this problem
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. Report back with this problem.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you.

Help needed with AT&T 3G MicroCell going through 1841 Router

I am trying to get an AT&T 3G MicroCell (made by Cisco) to communicate to the Internet through our Cisco 1841 Router.
The router has only basic NAT and no Firewall setting.
The AT&T 3G MicroCell is not a configurable device and it directly connected to a switch port on the router.
DHCP is supplied to it by the router.
We are using Comcast Business Class modem but it is set as a passive gateway pass through device so by passing the router is not an option.
The MicroCell is unable to establish connectivity with the AT&T auto-configuration on the Internet.
So far AT&T support has not been very helpful or knowledgeable.
Anyone have experience with the MicroCell device and connectivity?
They recommend some advanced settings for UPD and TCP ports but the router shows them as open.
It primarily uses ipsec ports
Any ideas?

I have this same issue with the MicroCell plugged directly into the WAN (DHCP) connection to the house from the ISP...................
I also have this same issue with the unit plugged into the DMZ on the router with pass all, all protocol's in and out .....
My problem is GPS related, as in the new 911 database has "virtually" moved my 2 bedroom house 4 miles east of my "physical" location.
Ain't modern tech great......(now if we could just get people great) only problem with high tech is............GARBAGE IN >> GARBAGE OUT........it still depends on "intelligent" life to program everything.

Need help setting up my router

hi i am new to this forum and i need some help
i just recently bought a linksys model: WRT54G ROUTER and a NETWORK USB ADAPTER and it wont connect to the internet using a wired connection and a wireless connection. i have COMCAST internet and i tryed calling them to see if they could help me but they couldnt. i also went to BEST BUY and asked the geek squad people and they said the lnksys setup disk doesnt work 9/10 times so can any one please help me so i dont have to spend 100+ dollars to get my internet setup through my router.
also my modem is directly connected to my comouter by a cat-5 cable(ethernet cable)
thanks in advance

Make sure you can access the Internet while directly connected to the modem then...
Check this out:
CLICK THIS
"The war between heaven and hell depends on the choices we make, and those choices require sacrifice. That's the test"

Need Help in finding out Router, Switch, firewall n IDS 4 Datacentre

Hii All,
Greetings!!!
Iam workin on project for Datacenter. I need ur help in finding me out the exact Router, Switch, Firewall & IDS series based on my attached complete technical specification.
pls find attched tech info for router, switch, firewall & IDS. Ur prompt respnse will be appreciated..
Thanku in advance 4 ur kind cooperation & help.
Looking forward 4 ur prompt response.
Brgds
Arif....

The write-up more sounds like it's an 7206VXR router, a 6500E with Sup720.
FW/ASA/PIX is an ASA 5510
Please don't forget to rate useful posts. Thanks.

I´m doing a design for presale, where I will need a router what support PAT for 500 or a little more of users, it not need any more features only static routing and dhcp pool for 500 users, can you help me for know what router recommend?

I´m doing a design for presale, where I will need a router what support PAT for 500 or a little more of users, it not need any more features only static routing and dhcp pool for 500 users, can you help me for know what router recommend?

What is your WAN speed currently and projected WAN speed in the next 3 years?

Hi, i need your help. I'm thinking of buying an iPod Touch 5..but i own a wireless G Router at home. So can iPod Touch 5 connect to a wireless G router? Will it connect easily and fast? Thank you.

Hi, i need your help. I'm thinking of buying an iPod Touch 5..but i own a wireless G Router at home. So can iPod Touch 5 connect to a wireless G router? Will it connect easily and fast? Thank you.

Hi, i need your help. I'm thinking of buying an iPod Touch 5..but i own a wireless G Router at home. So can iPod Touch 5 connect to a wireless G router? Will it connect easily and fast? Thank you.

Need basic Help - SG300 with vlan and routing

Hi,
i need some basic help with configuring vlan/routing.
Situation:
DSL Router - Cisco 300 - XenServer
192.168.1.253 - 192.168.1.19 - 192.168.1.10 (mgmt ip)
goal is, to reach from inside xenserver vms the internet.
vms = 192.168.2.x
gateway ip = 192.168.2.1
what i did:
- configured vlan 102, tagged, with the xenserver port
- configured on xenserver a network with vlan id 102, attached to the vm
- this network is conntected to an external bond
- configured ipva4 interface: vlan102 - Static - IP 192.168.2.1 (this is the gateway ip of the vms)
- automatic configured IPv4 Route: 192.168.2.0/24 next hop 0.0.0.0, Directly connected
So at the moment i cant ping from inside a vm to the DSL Router (192.168.2.2 to 192.168.1.253)
any ideas what i misconfigured or whats wrong?
cheers,
-Marco

Hi Tom,
ok, that make sense. I can ping the router now inside vms from 192.168.2.x network.
But i cant ping external adresses, error: Destination net unreachable.
My other problem i have, i cant reach any server from outside over router portforwarding.
How do i have to configure the upload port to the dsl router? Is it a access port or a trunk
port with all vlans (tagged or untagged?) At the moment ive a tagged Trunkport with all vlans.
IPv4 Interface Table
Interface
IP Address Type
IP Address
Mask
Status
VLAN 1
Static
192.168.1.19
255.255.255.0
Valid
Should the VLAN1 ip adress not the router ip adress ? Do i need an additional vlan for
the router ? At the end i like to change the switch ip from dhcp to static (change automaticly
when switching to layer 3 mode), but ive to look for the ios commands first.
What else do i missing ?
Thanks a lot,
Marcus

DlSW/SDLC 1841 ROUTER.

I have just tried to implement by first 1841 router.
I used the same template that I have for over 400 sites ( 1600 , 1700 , 2500 and 3600 series routers )
I get the dlsw peers established no problem.
The problem is on the serial interface in the router.
It is an IBM 5494 controller .
Here is the configuration that I have for the serial interface.
I have added the routers configuration.
Any ideas??? Is there something that I need to add to the serial interface on the 1841's that was not required before ???
My IOS is (C1841-ENTBASE-M), Version 12.3(11)T2
tks.

Hi,
please open a case with the tac. There have been a few problems with sdlc and 12.3T, also there are some issues depending on the hardware you are using.
The Tac will help you to collect all the needed information to understand your problem and then guide you to a resolution.
thanks...
Matthias

Do I need privilege exec level commands in router?

Do I need privilege exec level commands in router if the user was setup in TACACS server with specific privilege exec already?
The user is getting "Command authorization failed" error even was setup with "priv-lvl = 4" for TACACS server.
If changed to AAA with local authentication then is fine without privilege exec level 4 commands in router.

If you are using command authorization then privilage doesn't matter.
Best way to set it up is to give all user priv lvl 15 and then define what all commands user can execute.
Note : Having priv 15 does not mean that user will able to issue all commands.
We will set up command authorization on acs to have control on users.
This is how your config should look,
aaa authentication login default group tacacs+ local
aaa authorization exec default group tacacs+ if-authenticated
aaa authorization commands 1 default group tacacs+ if-authenticated
aaa authorization commands 15 default group tacacs+ if-authenticated
aaa authorization config-commands
aaa accounting commands 1 default start-stop group tacacs+
aaa accounting commands 15 default start-stop group tacacs+
Regards,
~JG
Do rate helpful posts

ACL's ON Cisco 1841 Router

Can you let me know what is the maximum no of ACL's that can be configured on Cisco 1841 router ?

Hmm I don't know if such metric is available out there. Perhaps a call/case with Cisco TAC would help! How many ACLs and ACEs do you need/plan to configure?
Thank you for rating helpful posts!

Need some Help configuring sip

Hi all ! ,
Im kind off new to sip calling and cisco telephony , but here goes ,: i have a 2821 router with CME installed
IOS : C2800NM-IPVOICEK9-M
Sofware version : 15.1(4)M4 / CME 8.6
Attached to GE0/0 is a CISCO 3750 switch
GEO - consisfts of 3 VLANS , the native
172.22.1.X
172.22.100.X VOICE
172.22.101.X DATA
my tftpserver = 172.22.1.150
i need some help configuring a sip trunk , i have 10 testing phonenumbers from vodafone , but i do not know where to start to get this working
i have tried
http://www.cisco.com/en/US/products/sw/voicesw/ps4625/products_configuration_example09186a00808f9666.shtml
but im getting stuck with what to fill in where .. is there anyone form NL whom has the same setup ? or similar ? or can give me some guidance on how to make the test calls

ok.. here goes
Building configuration...
Current configuration : 9721 bytes
! Last configuration change at 15:26:14 CET Thu Jan 2 2014
! NVRAM config last updated at 15:26:14 CET Thu Jan 2 2014
! NVRAM config last updated at 15:26:14 CET Thu Jan 2 2014
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
no aaa new-model
clock timezone CET 1 0
network-clock-participate wic 0
network-clock-participate wic 1
network-clock-select 1 E1 0/0/0
network-clock-select 2 E1 0/0/1
dot11 syslog
ip source-route
ip cef
ip dhcp pool VOICE
network 172.22.100.0 255.255.255.0
option 150 ip 172.22.1.150
default-router 172.22.100.1
ip dhcp pool DATA
network 172.22.101.0 255.255.255.0
default-router 172.22.101.1
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
isdn switch-type primary-net5
voice service voip
ip address trusted list
ipv4 172.22.1.50
ipv4 172.22.1.51
ipv4 172.22.100.1
ipv4 172.22.101.1
ipv4 62.140.159.225
callmonitor
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
sip
registrar server expires max 3600 min 3600
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
codec preference 4 g729br8
voice register global
voice translation-rule 1
rule 1 /5123781291/ /601/
rule 2 /5123781290/ /600/
voice translation-rule 2
rule 1 /^112$/ /112/
voice translation-rule 3
rule 1 /^.*/ /0262610290/
voice translation-rule 4
rule 2 /600/ /5123788000/
rule 3 /601/ /5123788001/
rule 4 /^2(..)$/ /51237812\1/
voice translation-profile CUE_Voicemail/AutoAttendant
translate called 1
voice translation-profile PSTN_CallForwarding
translate redirect-target 4
translate redirect-called 4
voice translation-profile PSTN_Outgoing
translate calling 3
translate called 2
translate redirect-target 4
translate redirect-called 4
voice-card 0
crypto pki token default removal timeout 0
controller E1 0/0/0
framing NO-CRC4
pri-group timeslots 1-31
controller E1 0/0/1
framing NO-CRC4
pri-group timeslots 1-31
ip ftp username cisco
ip ftp password cisco123
ip tftp source-interface GigabitEthernet0/0.1
interface GigabitEthernet0/0
no ip address
duplex auto
speed auto
no keepalive
interface GigabitEthernet0/0.1
encapsulation dot1Q 1 native
ip address 172.22.1.51 255.255.255.0
interface GigabitEthernet0/0.20
encapsulation dot1Q 20
ip address 172.22.101.1 255.255.255.0
interface GigabitEthernet0/0.100
encapsulation dot1Q 100
ip address 172.22.100.1 255.255.255.0
interface GigabitEthernet0/1
no ip address
shutdown
duplex full
speed 100
interface Serial0/0/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
interface Serial0/0/1:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
interface BRI0/1/0
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
interface BRI0/1/1
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
ip forward-protocol nd
ip http server
ip http authentication local
no ip http secure-server
ip http max-connections 16
ip http path flash:gui
ip route 0.0.0.0 0.0.0.0 172.22.1.50
tftp-server flash:7941/apps41.8-4-1-23.sbn alias apps41.8-4-1-23.sbn
tftp-server flash:7941/cnu41.8-4-1-23.sbn alias cnu41.8-4-1-23.sbn
tftp-server flash:7941/dsp41.8-4-1-23.sbn alias dsp41.8-4-1-23.sbn
tftp-server flash:7941/jar41sccp.8-4-1-23.sbn alias jar41sccp.8-4-1-23.sbn
tftp-server flash:7941/cvm41sccp.8-4-1-23.sbn alias cvm41sccp.8-4-1-23.sbn
tftp-server flash:7941/SCCP41.8-4-2S.loads alias SCCP41.8-4-2S.loads
tftp-server flash:7941/term41.default.loads alias term41.default.loads
tftp-server debug
control-plane
voice-port 0/0/0:15
voice-port 0/1/0
voice-port 0/1/1
voice-port 0/0/1:15
voice-port 2/0/0
voice-port 2/0/1
voice-port 2/0/2
voice-port 2/0/3
voice-port 2/0/4
voice-port 2/0/5
voice-port 2/0/6
voice-port 2/0/7
voice-port 2/0/8
voice-port 2/0/9
voice-port 2/0/10
voice-port 2/0/11
voice-port 2/0/12
voice-port 2/0/13
voice-port 2/0/14
voice-port 2/0/15
voice-port 2/0/16
voice-port 2/0/17
voice-port 2/0/18
voice-port 2/0/19
voice-port 2/0/20
voice-port 2/0/21
voice-port 2/0/22
voice-port 2/0/23
mgcp profile default
dial-peer voice 1 voip
description **Incomming Call from SIP Trunk**
translation-profile incoming CUE_Voicemail/AutoAttendant
session protocol sipv2
session target ipv4:172.22.1.50
incoming called-number .%
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
no vad
dial-peer voice 2 voip
description **Outgoing Call to SIP Trunk**
translation-profile outgoing PSTN_Outgoing
destination-pattern 9........
session protocol sipv2
session target ipv4:172.22.1.50
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
no vad
dial-peer voice 3 voip
description **Outgoing Call to SIP Trunk **
translation-profile outgoing PSTN_Outgoing
destination-pattern 9[2-9]..[2-9]......
session protocol sipv2
session target ipv4:172.22.1.50
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
no vad
dial-peer voice 4 voip
description **Outgoing Call to SIP Trunk**
translation-profile outgoing PSTN_Outgoing
destination-pattern 9[0-1][2-9]..[2-9]......
session protocol sipv2
session target ipv4:172.22.1.50
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
no vad
dial-peer voice 5 voip
description **911 Outgoing Call to SIP trunk**
translation-profile outgoing PSTN_Outgoing
destination-pattern 911
session protocol sipv2
session target ipv4:172.22.1.50
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
no vad
dial-peer voice 6 voip
description **Emergency Outgoing Call to SIP Trunk**
translation-profile outgoing PSTN_Outgoing
destination-pattern 9911
session protocol sipv2
session target ipv4:172.22.1.50
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
no vad
dial-peer voice 7 voip
description **911/411 Outgoing Call to SIP Trunk**
translation-profile outgoing PSTN_Outgoing
destination-pattern 9[2-9]11
session protocol sipv2
session target ipv4:172.22.1.50
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
no vad
dial-peer voice 8 voip
description **International Outgoing Call to SIP Trunk**
translation-profile outgoing PSTN_Outgoing
destination-pattern 9011T
session protocol sipv2
session target ipv4:172.22.1.50
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
no vad
dial-peer voice 9 voip
description **Star Code to SIP Trunk**
destination-pattern *..
session protocol sipv2
session target ipv4:172.22.1.50
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
no vad
dial-peer voice 10 voip
description **CUE Voicemail**
translation-profile outgoing PSTN_CallForwarding
destination-pattern 600
b2bua
session protocol sipv2
session target ipv4:172.22.1.155
dtmf-relay sip-notify
codec g711ulaw
no vad
dial-peer voice 11 voip
description **CUE Auto Attendant**
translation-profile outgoing PSTN_CallForwarding
destination-pattern 601
b2bua
session protocol sipv2
session target ipv4:172.22.1.155
dtmf-relay sip-notify
codec g711ulaw
no vad
sip-ua
authentication username 0262610290 password 7 15020A1F173D24362C realm 62.140.1
59.225
authentication username 0262610290 password 7 021605481811003348
no remote-party-id
retry invite 2
retry register 10
timers connect 100
registrar ipv4:62.140.159.225 expires 3600
sip-server ipv4:62.140.159.224
host-registrar
telephony-service
max-ephones 58
max-dn 192
ip source-address 172.22.100.1 port 2000
calling-number initiator
system message testing
cnf-file location TFTP tftp://172.22.1.150/
load 7960-7940 P00307020200.loads
load 7941 SCCP41.8-4-2S.loads
load 7941GE SCCP41.8-4-2S
time-format 24
dialplan-pattern 1 26261029.. extension-length 3 extension-pattern 9..
voicemail 600
max-conferences 12 gain -6
call-forward pattern 9.T
moh music-on-hold.au
web admin system name admin password password
dn-webedit
time-webedit
transfer-system full-consult
secondary-dialtone 9
directory entry 1 101 name 101
create cnf-files version-stamp 7960 Jan 02 2014 08:40:49
ephone-dn 1
number 290 secondary 0262610290
name Phone 1
hold-alert 30 originator
ephone-dn 2
number 291 secondary 0262610291
name phone 2
hold-alert 30 originator
ephone-dn 3
number 292 secondary 0262610292
name Phone 3
hold-alert 30 originator
ephone-dn 4
number 293 secondary 0262610293
name Phone 4
hold-alert 30 originator
ephone-dn 5
number 294 secondary 0262610294
label Phone 5
hold-alert 30 originator
ephone 1
mac-address 0019.E88F.3BDD
button 1:1
ephone 2
mac-address 001E.4A92.0A27
type 7961
button 1:2
ephone 3
mac-address 0012.43F5.03AF
button 1:3
ephone 4
mac-address 000F.F7AC.502A
button 1:4
ephone 5
mac-address 0019.E851.090A
button 1:5
line con 0
line aux 0
line vty 0 4
login
transport input all
scheduler allocate 20000 1000
ntp master
end

Need a help to config 1841 router!

Similar Messages

Maybe you are looking for