Need answer about ATI/Radeon 9600 Screen glitch: lost in 2008 stale link!
Hi, I read this with relief that it describes exactly my problem (mouse trails after a clean re-install of Leopard, 30" Apple Cinema Display, PowerPC G5). Alas the website (blog) referenced that has the complete description of the fix is completely offline. Can someone help me dig up what to do?
http://discussions.apple.com/thread.jspa?threadID=1356236
Thanks,
-DB
I don't want to boot and not be able to see the screen at all.
Yeah, and I'd hate to be part of that! But after moving the present one(s) out to a safe place and if you get no video, a Safe Boot from the HD, (holding Shift key down at bootup), should by all rights load a "Safe Driver" for basic video.
Using mv is fine, don't need a specialized tool?
Yes.
run the installers downloaded for 10.4.x and reboot?
Not sure if 10.4 ones work, perhaps earlier 10.5 ones, but you'll likely have to use Pacifist...
http://www.charlessoft.com/
then extract/install what you need from your Install Disk.
Similar Messages
-
Dual monitors on the ATI Radeon 9600 XT black screen on 2nd monitor
i have problem on second monitor , it always turn black during my work, and in a second it turn back to work well again, about 20-30 minutes a time .
can anyone here give me some help ? it really make me go crazy....
Thanks!
POWER MAC G5 DUAL 2.5 +ATI Radeon 9600 XT+2 SUMSUNG 205BW
The one connected to the ADC no problme.LOGIC CAT-
My guess is either a bad cable or bad adapter on the second monitor. Try switching the monitors and see if the problem follows the monitor.
Luck-
-DaddyPaycheck -
PPC G5 with ATI Radeon 9600 Pro monitors not getting signal
hi there.
I have a PPC G5 with ATI Radeon 9600 Pro graphics card and I cannot get a monitor to work properly. I am trying an old Apple Studio Display (circa 2001) and a Viewsonic VA520.
It seems like the Apple display should work, but all I get is a black screen. I ran it through a DVI to ADC adapter and had it working for a short period of time, but for some unknown reason it went back to the black screen.
The Viewsonic gives a 'NO SIGNAL' screen and not much else.
Both of these monitors have worked on other G5's. I am guessing this is a graphics card issue.
I appreciate any kind or helpful words! Thank you.I'm having a similar problem with the G5 not recognizing a VGA monitor on either video out. I have no problem using two monitors with the DVI inputs but I need to use a VGA video splitter for a third screen. It worked at the beginning of this week, and now it refuses any VGA out, even without the splitter, just going into directly into the VGA in of one of my working monitors via a DVI-VGA adapter(i've tried different ones). I read another post about trashing "displays" and "windowserver" preference files but i haven't yet tried that..any clues??
-
MS-6309 motherboard and ATi radeon 9600 Pro
I have a MS-6309 motherboard. I have recently installed an ATi Radeon 9600 Pro 128MB graphics card and am having some problems. I am running Windows 98. I can't get Direct 3D and AGP Texture Acceleration (this is disabled) to work. I want to download the latest drivers for my motherboard but don't know which link to choose on the motherboard drivers page of the MSI web site.
The problems that occur are:
1) The screen freezes up
2) The graphics on the screen go blurry
3) Everything stops and the monitor switches off
I am sure this is a driver issue and not a hardware issue. Please can someone help me!chances are you need a better psu than you had before actually
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=124
has the drivers -
Hi,
I have a G5 tower with ATI Radeon 9600 Pro running two fujitsu LCDs, both at 1680x1050, 60 hz. Today, they're both incredibly fuzzy - bordering on unusable. They remain this way if I step down to lower res.
This is only on my login. My wife's login = crisp and clear. Likewise the login screen. Have tried resetting the PRAM, no change.
One thing I do notice today is that the very far right edge of the menu bar is bleeding over into the right screen, which I don't recall it used to do.
Also, the display is shifting about on the horizontal axis, like it's trying to find a better line sync or something (to use an old CRT metaphor)
Any help much appreciated, Robbie
Dual 2GHz G5 Mac OS X (10.4.9)
Dual 2GHz G5 Mac OS X (10.4.9)Hi-
Welcome to Discussions!
Something new in your (user) startup items?
Since it only occurs in your account, you could have some incompatible extension/utility, or be missing one.
Might compare yours to your wifes-
System Preferences/Accounts/Login Items
Might check to see if you have any Universal Access preferences enabled-
System Preferences/Universal Access -
20" ACD, ATI Radeon 9600, and Me
hello all!
Just a quick question. I'm (semi) technically proficient and am pretty good with hardware, but still uneasy with Apple stuff.
I have a ATI Radeon 9600 I believe (It's somewhere around there; whatever came stock with the unit)and I'm going to purchase a 20" ACD in a couple of weeks and have a question:
Now I know that the card is a massive 64 MB! (lol) and I've never upgraded cause never really had a reason. I am aware of splitting your vram over 2 displays can hinder the display causing ghosting and graininess and wondered what you guys thought about purchasing another card to run this display. I have to hold onto my ATI because of the ADC connector, and dropping 99 bucks for a converter is not a wise decision for me quite yet. Now I've been made aware of running multiple cards on a unit. It can't be as simple as popping in another card and taking it from there would it?!? The OS would go nucking futs figuring out what card to use and such I would assume.
So, after all that rigamarole:
CAN I run 2 cards on my MDD dual G4?
If so, how?
also, SHOULD I run a second card if I can (you guys with this setup can help me tons!)
if so, what card would you guys recommend. I'm looking around the 128 MB variety. I don't want to break the bank, getting an 800 dollar display, then a 300 dollar card.
edit: also, the max rez on the 17" studio is 1280 x 1024 and the 20" ACD 1680 x 1050. That shouldn't be a problem should it? I mean, it's only REALLY adding pixels length wise, and only 26 more height so the 20" won't be knocked down in rez to make up for this right?
(forgive my ignorance, though I've used the dual-display setup, I've never owned one. and to be fair, that one had the same size monitors on both)
So, guys (and gals) help me out here!Mr Mayhem,
if I understand you correctly, you want to use the (older/ADC connection) 17" apple display together with the (newer/DVI connection) 20" apple display together on your MDD Dual 1 G.
My first advice would be to get two displays of the same kind. You will love that (equal screen resolutions just feel better somehow) ... get a 2nd hand 17" or, even better, ditch the 17" and get two 20".
In case you rather stick to your original plan - just get the ATi Radeon 9200 Mac Edition and put it in one of the PCI slots of your MDD. It will feed the 20" via DVI conncetor and it'll cost you roughly around 100.- and the 128 MB onboard RAM will be ok for standard use; maybe just not for betatesting Quake VII Arena. Probably the best bang for buck in your situation. Lood Guck ! -
ATI Radeon 9600 Mac & PC Edition will not work with leopard
When I installed a new ATI Radeon 9600 Mac & PC Edition, 256MB; my Dual 2 GHz G5 (June 2004) will not allow me to drive my Apple Cinema Display while running under leopard, (neither 10.5.1 or 10.5.2 with Leopard Graphics Update).
The mac starts up as usual and gets to the white screen with Apple logo -then the progress ring eventually stalls. The mouse pointer becomes visible and can be moved freely around this screen.
I can connect from other macs on the network and navigate files, but screen sharing results in an all black window.
The Radeon 9600 works fine if I start up the mac with the Tiger installation disk.
I have tried every suggestion that I could find on these boards and elsewhere: zapped the pram, reset the SMU, installed older ATI Drivers, etc...
Of course the G5 is far out of warranty. I've been running Leopard since the day it shipped - so that's out of warranty now, and there is little help to be found on the ATI/AMD website. I'm afraid I'll have to return the card before Apple releases another graphics update.
The stock graphics card that came with this mac is the nVIDIA 64MB GeForce FX 5200 - but it's having trouble keeping up with Leopard's demands - my isight barely works, most special effects in iChat and PhotoBooth are unusable, and of course I'm not given the option to use a transparent menu bar,
I am really good at swapping video cards in the G5 now - but I'm so frustrated.
Does anyone else have any suggestions?
thanksHello I have Grafic card ATI Radeon 9600 Pro-256MB install. after Updates. I was after *delete all ATI files besides*
ATINDRV.kext
ATITVOut.kext
ATIRadeon.kext
ATIRadeon9700.kext
ATIRadeon9700DVDDriver.bundle
ATIRadeon9700GA.plugin
ATIRadeon9700GLDriver.bundle
ATIRadeon9700VADriver.bundle
ATIRadeonDVDDriver.bundle
ATIRadeonGA.plugin
ATIRadeonGLDriver.bundle
ATIRNDRV.kext
from System/Library/Extensions run ther 30'' Cinema, mit 2560x1600 but without Quartz Extreme . *I'm very angry of APPLE* 3 week without help, 5 Telefon support with Apple, with ATI without solution.
I know that ATIRadeon9700.kext drive Quartz Extreme. But I don't know what can I do too.
My solution for this moment is only this one. If I know my solution from Apple, ATI or another one look sometimes on
http://discussions.apple.com/thread.jspa?messageID=6645245�
Message was edited by: knoche
Message was edited by: knoche -
Max TV (lcd or plasma) for Dual PowerMac G5 - ATI Radeon 9600 XT
Hi,
Wanted to pose a question as to what the maximum size TV (lcd/plasma) would be if I wanted to use a PowerMac 2x2.0Ghz ATI Radeon 9600 XT video card.
I want it to be the primary display and use it for video conferencing only.
Thanks,
NikeshThe problems are with the TVs, not the card. Some TV makers only test their DVI/HDMI inputs with video equipment, such as cable boxes, DVD players, and HD video cameras. These all use just a few resolutions (720p, 1080i, 1080p). They are sending video, and clipping of the edges is not a major problem, although there is no good reason to do it with digital video. These devices send out their digital video at their built-in resolution, and don't have to get any resolution information from the display. A computer graphics board can generate many different resolution and relies on the display telling the board which resolutions will work. Some TVs don't send back the correct information, so you may need special software to force the graphics board to a resolution that it doesn't think is supported by the display. Overscan is also done by some TVs. Some, but definitely not all, graphics boards can be set to underscan to get all the desktop on the display, but the pixels may not match exactly, causing some blurring. It is a lot better if a 1920 x 1080 TV will just display the computers 1920 x 1080 on a pixel-to-pixel basis. Some Sony and Westinghouse 1080p sets work properly, some Samsung 1080p don't, but there is no way to tell unless you try it, or can find a pixel-to-pixel mode in the TV manual. Look for sets that support 1080p, not just 1080i.
-
ATI Radeon 9600 and PowerMac G4 QuickSilver - problem
Hi guys!
Sorry for the big amount of posts but I have yet another problem.
Yesterday I replaced the stock Nvidia GeForce2 MX in my QuickSilver with an OEM ATI Radeon 9600 128MB from my G5. I taped the pins 3 and 11 and the card worked immediately.
After using the Mac a bit, I noticed that the graphic performances are pretty much exactly the same as before. I installed Leopard and I got the translucent menubar, but the graphic performances are terrible (seems exactly as bad as the GeForce).
Does anyone have the same issue? Here is a screenshot from System Profiler in both Tiger and Leopard:
And here are some Xbench scores (the same card in the G5 scored about 121 points):The DP800 shoild help, especiall the 1 MB L3 per CPU, but the Bus speed is still a bottleneck.
Overall, the Geekbench scores almost doubled, from 372 on the 733, to 670 on the DP800, which was mostly CPU not Graphics improvement, but you should see some.
I only have Xbench results for my QS2001 with upgraded CPUs to 1.47 DP/7455s & an MX2 it seems...
Results
146.05
System Info
Xbench Version
1.1
System Version
10.3.5
Physical RAM
1024 MB
Model
PowerMac3,5
Processor
PowerPC G4x2 @ 1.47 GHz
Version
7455 (Apollo) v3.3
L1 Cache
32K (instruction), 32K (data)
L2 Cache
256K @ 1467 MHz
L3 Cache
2048K @ 4.16 GHz
Bus Frequency
134 MHz
Video Card
GeForce2 TwinView
Drive Type
WDC WD1200BB-00CAA0
CPU Test
163.16
GCD Recursion
182.54
7.13 Mops/sec
Floating Point Basic
183.66
653.17 Mflop/sec
AltiVec Basic
182.95
2.66 Gflop/sec
vecLib FFT
113.59
1.75 Gflop/sec
Floating Point Library
183.42
7.34 Mops/sec
Thread Test
187.53
Computation
177.19
1.43 Mops/sec, 4 threads
Lock Contention
199.15
2.50 Mlocks/sec, 4 threads
Memory Test
116.12
System
159.57
Allocate
857.50
289.11 Kalloc/sec
Fill
124.56
991.53 MB/sec
Copy
104.09
520.46 MB/sec
Stream
91.27
Copy
93.16
379.93 MB/sec [altivec]
Scale
91.50
380.09 MB/sec [altivec]
Add
89.52
377.76 MB/sec [altivec]
Triad
90.99
374.51 MB/sec [altivec]
Quartz Graphics Test
145.34
Line
119.01
3.03 Klines/sec [50% alpha]
Rectangle
123.73
8.70 Krects/sec [50% alpha]
Circle
135.90
3.13 Kcircles/sec [50% alpha]
Bezier
130.84
1.42 Kbeziers/sec [50% alpha]
Text
342.87
5.59 Kchars/sec
OpenGL Graphics Test
153.13
Spinning Squares
153.13
107.16 frames/sec
User Interface Test
233.57
Elements
233.57
79.47 refresh/sec
Disk Test
98.39
Sequential
107.10
Uncached Write
109.10
43.43 MB/sec [4K blocks]
Uncached Write
110.63
43.18 MB/sec [256K blocks]
Uncached Read
96.87
15.33 MB/sec [4K blocks]
Uncached Read
113.40
45.82 MB/sec [256K blocks]
Random
90.99
Uncached Write
79.92
1.14 MB/sec [4K blocks]
Uncached Write
92.08
20.77 MB/sec [256K blocks]
Uncached Read
92.10
0.61 MB/sec [4K blocks]
Uncached Read
102.80
21.16 MB/sec [256K blocks] -
1360 X 768 Resolution with ATI Radeon 9600 Pro
Maybe this isn't the right forum, but I've been surfing for hours with no luck so please forgive me if this seems out of place.
I output a show recently to QuickTime at 720 24 fps. I'd like to watch it on my 40" Samsung 720 HD TV. I cabled up and managed to get a picture in nearly fullscreen and nearly appropriate aspect ratio, but it doesn't look all that hot. Samsung tells me I want to set my Display settings on my Mac to 1360 x768 to achieve optimum picture. I told them I don't have that option in my settings. They said I probably need to update my driver on my ATI Radeon 9600 Pro video card. I did, still no 1360x768 setting. They said I might want to install the ATI Displays utility. That doesn't seem to offer anything useful. ATI's online support says I might want to install ATI's latest ROM updater, but I can't find any such thing even though the web seems full of mentions of such a beast.
Anyone have any ideas or any suggestion as to where I should post this question?
MartinFYI:
http://discussions.apple.com/help.jspa#answers
Steve should get the Solved Green Star...
Patrick -
Total lockup KM4M-L w/ ATI Radeon 9600 Pro
OK, its been a while since ive had any problems at all but unfortunately I am getting problems with my KM4M-L based PC completely locking up.
I am pretty sure that this is a graphics related issue since it started when I installed an ATI Radeon 9600 Pro 128MB.
I tried removing old nVidia drivers completely, have jusy formatted and re-installed Windows XP Pro with SP2, but the problem is still there. I have tried the card on AGP 2x and 4x, with fastwrite enabled and disabled, and different memory allocations of 64MB and 128MB, but still no joy.
I have also tried the latest two sets of drivers from ATI with no joy, and the latest chipset drivers & BIOS revisions from MSi.
Does anyone know of any compatibility issues between my hardware or something I may have missed in my frustration? Thanks, Huw
Mercury 400W PSU Specs: 3.3V 28A 5V 40A 12V 17A
MSI KM4M-L
AMD Athlon XP 2600+
Crucial 1x512MB PC2700 RAM
ATI Radeon 9600 Pro 128MB
M-Audio Audiophile 24/96
Excelstor 80GB 7200RPM HDD
Maxtor 20GB 5600RPM HDD
LG 52x32x52 CDRW
Unbranded 32x CDROM
S-Talent 128MB Flash Drive
Netgear WG111 USB 802.11g Network Adapter
Thermaltake Xaser DesktopOK, I have tried a number of things since posting last.
I have been running the PC without the video card, just using the onboard graphics, which didnt seem to help.
I have air dusted, and replaced the GPU heatsink and fan for a large machined one with a more appropriate size of fan but im still getting some problems:
The first is the complete lock-up, which still occurs at seemingly random intervals with no pattern at all.
The second problem is quite frequently on botting the computer, when windows has loaded, the screen display seems to breakdown into random pixels as soon as I start using anything, the effect is hard to describe but its almost as if the screen is being airbrushed, very odd
I should add that I have also removed the Maxtor HDD, since last posting, and also run a series of MemCheckx86 tests which seem to indicate that the RAM is fine.
Any ideas anyone? I am starting to suspect that there may be multiple problems contributing to this annoyance -
Help : Will ATI Radeon 9600 Pro run a 30" Cinema Display ? ? ?
just a simple question as the subject suggests /
i have a 1st generate Power Mac G5 Dual 2GHZ / with Radeon 9600 Pro
graphics card . i would simply like to know if it will plug an play nicely
with a 30 inch monitor - be it the Apple Cinema Display or Dell -
anyone have any definitive answers / my thanks in advance
best,
lexYou need a different graphics board with dual-link DVI to run the 30" at full resolution. The AGP cards Apple sold that have dual-link DVI ports are:
ATI Radeon 9650 XT (one single-link, one dual-link DVI)
NVIDIA GeForce 6800 GT DDL (two dual-link DVI)
NVIDIA GeForce 6800 Ultra DDL (two dual-link DVI)
Apple doesn't sell these as retail items, but might sell them as replacement parts, or you could look for them used. Be sure to get Mac versions.
There are two new graphics boards that will work:
ATI Radeon® X800 XT MAC Edition RoHS 256MB AGP (one ADC, one dual-link DVI)
<http://shop.ati.com/product.asp?sku=3170810>
ATI Radeon® 9600 Pro PC & MAC Edition RoHS 256MB AGP (one single-link, one dual-link DVI)
<http://shop.ati.com/product.asp?sku=3170809> -
ATI Radeon 9600 Pro and 2560 x 1600
Hi,
I've got a Radeon 9600 pro and just purchased a new 30" display. However, I can't seem to get it running at 2560 x 1600 - does this card support this resolution?You will need a graphics card with dual-link DVI.
Starting with the fastest:
ATI Radeon X800 XT 256MB (ADC, dual-link DVI)
<http://www.welovemacs.com/0831xeghr.html>
NVIDIA GeForce 6800 Ultra 256 MB (Two dual-link DVI)
<http://www.welovemacs.com/6613332.html>
NVIDIA GeForce 6800 GT 256 MB (Two dual-link DVI)
<http://www.welovemacs.com/6613441.html>
ATI Radeon 9650 XT (Single-link, dual-link DVI)
<http://www.mac-pro.com/ATI-Radeon-9650-256MB-for-G5-661-3593?sc=2&category=42>
ATI Radeon® 9600 Pro PC & MAC Edition 256MB AGP (Single-link, dual-link DVI)
<http://shop.ati.com/product.asp?sku=3170809> -
ATI Radeon X800 XT or ATI Radeon 9600 Pro Mac Edition for 30" display
I currently have the ATI Radeon 9600 Pro installed in my G5 2.0 DP and it is running my 30" display, but I am having some isssues when I play DVD's the pictures seems to skip every few seconds like it isn't playing fast enough, or it hesitates. I bought the ATI Radeon X800 XT and wanted to know if that would be a better card before I switch it out.
The X800 is a faster card but DVD playback doesn't put much load on the card, so the X800 probably won't help. If it skipping on more than one DVD, the DVD drive is probably having problems. Cleaning the lens ay help.
-
ATI Radeon 9600 XT & SyncMaster 305T - problems
Hi everyone - I just purchased a 30" Samsung SyncMaster 305T and have been trying to get it to run properly. I have a Dual 1.8 GHz G5 with the ATI Radeon 9600 XT card. The largest resolution it's allowing me to set on the monitor preferences window is 1280x800 (ideally i'd like the option for 2560 x 1600). Anyone know if there's any incompatibility issues with this monitor/graphics card combo? Please help.... otherwise, i'll have to either return the monitor or buy a new graphics card. Soooooo bummed. =[ Thank you in advance!
Welcome to the forums, Rabidart!
First off, you're probably better off starting a new topic for your question, since this one is marked as "answered" and many folks won't see your new question at the bottom.
But since I'm already here...
Secondly, I notice that you're running Leopard. I'd recommend staying away from the ATI cards if you're powering a 30" on a G5. For an explanation, check out this thread:
http://discussions.apple.com/thread.jspa?threadID=1195747&start=0&tstart=0
You have two options: deal with the inherent ATI issues until Apple or ATI/AMD address them, or get a compatible nVidia GEForce AGP card with Dual-Link DVI. There are many on eBay, and a few users in the thread listed above have installed them with a 100% success rate (so far).
By the way, a replacement card, once you find one, is VERY easy to install. Retail packages will include instructions, and many of the sellers on eBay include instructions with theirs.
Good luck!
Maybe you are looking for
-
I want to move the "Clear (Private Data)" menu item back to the tools menu. Menu Editor's dev didn't anticipate this so my usual option for shuffling menu commands around won't work. * I know there is a keyboard shortcut to open it. * I know it has b
-
How to make column heading in a table cross multiple pages
I have a large table that crosses over to a second page. I would like the column headings to be displayed on the second page. Is this possible and how to do it?
-
Why is Advanced Replication available with Standard 8i?
I was installing Oracle 8i "Standard" today on RH6. When I ran dbassist it offered an option to install Advanced Replication. According to the white papers online, Advanced Replication is not an Option available for 8i Standard, unless I am misreadin
-
IPhone randomly needing restore and then not letting me?
Ok, so my four week old iphone 3gs just up and stopped working. i got an alert on the iphone screen saying "iphone cannot make or receive calls. restore in itunes" so i tried restoring it and it didnt work. i updated my itunes, tried again, and it al
-
Compute sum of two columns - display result in the third column
Hello, I have a report and I want to compute sum of two report columns and display the total in the third column. For example: Sample_My_Report Col1 Col2 Total (Col1+Col2) 3 7 10 can anyone help me out with this issue. thanks.