Need bluetooth stereo head phones

Does anyone know where i can buy a set of nokia bluetooth stereo headphones (model BH-503). Getting no joy from the australian customer care center, which for some useless reason seems to be based in india. I am desperate. Have broken two sets of the earlier BH-501 model as they have a design fault (no wonder nokia is now giving them away) and hope BH-503 has been designed with this fault in mind. (they have to be daft if they don't already know about the fault, and the fact that BH-501 is 'close moulded' and therefore not repairable).
Moderator Not: Telephone number removed.
Message Edited by kenken on 05-May-2008 12:45 PM

You can buy one from this Australian online retailer:
www.expansys.com.au/p.aspx?i=161719

Similar Messages

IPhone 5s with hearing aids via Bluetooth. Need to use the phone for voice, what's the best distance that the mic will pick up your voice

I wear hearing aids that are made for Apple, the audio will go into the hearing aids via Bluetooth. I'll need to use my phone for voice only.. I drive for work and have a wok oh one too and both are synced to a bluetooh headset (LG). I'm trying to figure out how to talk on both phones ( use speakerphone on work phone?) without using a bluretooh headset. I don't know the range of the microphone on the IPHON, thinking about hanging it around my neck or put the phone into a stand/holder on the dash and use the speakerphone feature. Looking for ideas to make this simple

You can't do anything with that problem.
Take your iPhone to the closest Apple Store and they will give you new one for 200€/$ or if you bought your iPhone in less than 12 months you will get it for free.

I have a 24" mid 2008 imac when i plug the head phone jack into my stereo i have a hum that never goes away.

i have tried grounding both the head unit and also the computer it self and all i find is the noise is still there. what can i do to get rid of the noise? i think the problem is in the grounding of the head phone jack it's self but i dont know. has any one else had this same problem? thanks for your time.

How did you confirm grounding? How old is your house? Does it have 3-prong outlets? If not, there's no guarantee they are wired right even if they are the ones with one wider prong slot. If they are 3-prong, that's still no gurantee they are wired right. You would need one of the below to be sure. Just trying to save a lot of troubleshooting of devices when it could be your house wiring.

HT3887 Hi I have just got some new wWas iireless head phones and when I use them with the Bluetooth on my iPhone 4S it breaks up all the time even from short distance but when using my girlfriends iPhone 5 or iPad it's fine no problems atall!!! Any ideas

Hi I have just got some wireless head phones and while using Bluetooth with my iPhone 4S the sound breaks up all the time but if I use a friends iPhone 5 or my iPad it's fine no problems atall! Any ideas what the problem could be people??????

Unpair the headset from the phone with the problem. Restart the phone (hold HOME and SLEEP until an Apple logo appears), the pair the headset again. Also, look for things nearby that may be causing interference in the Bluetooth band. Cordless phones are a common cause of interference.

IPhone6 does not pairs with bluetooth head phones

I had been using Bose wireless head phones with iPhone 4S, recently I bought iPhone 6 but now I am not able to use my bluetooth head phones as the new iPhone6 does not reads them. Would appreciate any information on how I can correct this issue.

Hello anilfromtokyo,
Thanks for the question. After reviewing your post, it sounds like youare having trouble finding a bluetooth accessory. I would recommend that you read this article, it may be able to help you isolate or resolve the issue.
iOS: Troubleshooting Bluetooth connections - Apple Support
Thanks for using Apple Support Communities.
Have a nice day,
Mario

Why do i have to pair my bluetooth head phones every time I want to use them?

Every time I want to use my Philips Bluetooth head phones, I have to unpair them and then pair them again. They say connected in blue tooth settings, but no audio is coming through. Worked flawlessly with my RAZR Maxx. This is something I use a lot, and may make this phone a return.

Yikes, I know how important it is to have the bluetooth working with out any issues, jwennrn. Are you still trying to use the bluetooth with the Droid Razr Maxx or with a different phone? Was there any new updates or applications that were downloaded when you noticed this problem started? Please keep us posted. I'm eager to work with you to get this working again.
KevinR_VZW
Follow us on Twitter @VZWSupport

Hello i would to play my ipod nano radio via my Bluetooth speakers but it only plays via the head phones is there anyway around this . thanks

Hello I was hoping to listen to my ipod nano radio stations via Bluetooth speakers but I can't get this to work it only plays via head phones Thank s for any help

The same problem I have today afternoon.
My car audio system is compatible with iPod USB connector and worked fine for also 6 months.
When connecting my iPod nano 6rd gen via USB to car audio system, iPod displays on its screen a sucessfull connection, and music tracks is successfully displayed on the car audio system. But do not play. Switch forward or backward by playlist (by the buttons on the car audio system) works also, but still there is no start playback.
I tried plugged my iPhone 5 via USB to car audio system - it's works fine.
I plugged iPod to my mac computer - itunes says it's all Ok.
I am confused and do not understand what is happening.
May be restoring to default factory settings iPod....

My brand new iPhone 5 keeps saying "Connection Unsuccessful: Make sure "___" is turned on and in range" when I try to connect to my BlueTooth Stereo.

I just bought a brand new iPhone 5 (White and Gold) and have been having trouble keeping it connected to my BlueTooth Stereo. The stereo was purchased brand new back in September and is current on all software. Before I had my iPhone 5, I had the iPhone 4 and had no troubles with it connecting or remembering to connect to the stereo when it was in range. Now, in order to connect to it, I have to first "forget the device" then search for it again, find it, and connect. As soon as I turn either the stereo off, turn the iPhone off, or switch modes on the stereo (to CD mode, radio, etc) it loses the connection and does not pick it up again. It still shows up in my list of available bluetooth devices, but when I try to connect it says "Connection Unsuccessful: Make sure '____' is turned on and in range" which of course, it is.
I bought this stereo because I am a music teacher and use my phone frequently when teaching my classes. You can probably imagine how cumbersome it becomes when after each class if I have alternated between using my iPhone to play music or switching to CD mode, I then need to "forget the device" and follow the steps I outlined above to get it working again.
Has anyone else had this problem with the new iPhone and does anyone have a solution (I HOPE!!!!!)
Thanks!
-Disgruntled Music Teacher

I've not seen this type of behavior, but see if this support document helps. http://support.apple.com/kb/HT1664

Hey i have a ipod touch and i can t get any sound out of my head phones. The lil bit i can get is scratchy and very very low??

I have a ipod touch and i can only get a very lil bit of sound and its scrachy souding out of my head phones... sounds good if you dont use head phones??? Can anybody help??

Your MacBook Pro doesn't have HDMI output... it's DVI. For sound, you will need to use the headphone out/optical digital audio out port to the TV/stereo. As far as video goes, I'm confused as to what cable you're using but at one point you're converting DVI to HDMI.

Head phone not working...

head phone not working after i update to yosemite , I tried with different headphones but it didn't work. I am able to control the volume with the head phone buttons.

Take each of the following steps that you haven't already tried.
1. If your model has an audio-out (headphone) port, and a red light is coming from it, the internal switch is stuck in the position for digital output. You may be able to free it by inserting and removing a mini-stereo jack of the proper size. Inserting any kind of tool in the port may cause damage that won't be covered by your warranty.
If there's no red light, the switch may still be stuck in the headphone position. Try to free it the same way.
2. From the menu bar, select
 ▹ System Preferences ▹ Sound ▹ Output
Check the settings. The internal speakers should be selected as the output device, the Mute box should not be checked, and the volume slider should be at least halfway to the right.
3. Boot in safe mode. It will take much longer than usual. You don't have to log in; just reboot as usual when the login screen appears. Note: If FileVault is enabled under OS X 10.7 or later, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode.
4. Reset the NVRAM.
5. Reset the SMC.
6. Reinstall OS X after backing up all data as a precaution. You won't need your backup unless something goes wrong.
7. Make a "Genius" appointment at an Apple Store.
Back up all data on the internal drive(s) before you hand over your computer to anyone. If privacy is a concern, erase the data partition(s) with the option to write zeros* (do this only if you have at least two complete, independent backups, and you know how to restore to bare metal from any of them.) Don’t erase the recovery partition, if present.
*An SSD doesn't need to be zeroed.

Bluetooth stereo and settings

Hi all.
Got a bit of an issue with my Bluetooth, or more to the point my Alpine car stereo.
I’ve paired it with the iPhone fine and it connects first time every time and all my contacts sync perfect. However the head unit works with iPod/iPhone and connects via a lead to a dock connector. The problem is that if the phone is connected and I start the car, the music plays but as soon as Bluetooth connects, it mutes the music as the device has switched to Bluetooth stereo mode as it thinks it’s a Bluetooth headset?
To get music playing again I have to either disconnect then re-connect the iPhone of turn Bluetooth off.
What I want to know is, is there a way to turn Bluetooth headset off and what do the other settings do on Bluetooth device menu. I think I could guess what they do but I want to confirm to see if any will resolve my problem.
So what do the following do: 'Phone Favourites', 'Phone Recents' then in other groups 'All Contacts' is ticked?
Thanks in advance

Got a bit further with an answer after speaking to Alpine
Apparently this is known issue from the latest iPhone software update with the 3GS that is affecting many devices. Alpine are aware and their top people have informed Apple who have acknowledged the problem and apparently are working on a fix in the next update
The person I spoke to was surprised the iPhone had no way to turn bluetooth streaming off, i'm not! Another set of options were not allowed to touch, cheers Apple

Head phone volume controls are not working after updating to ios 6.1 y?

head phone volume controls are not working after updating to ios 6.1 y?

I have tried my head phone with other iphone still the same problem may be my head phones has been not working need to chek my iphone with other head phones which are working

Can you use the mic of a bluetooth stereo headset on an iPod touch 2G w/ fi

Hi guys.
I have a Dell bluetooth stereo headset with mic incorporated.
I want to use this to have conversations with my iPod touch, using voip software.
Can this be done? I'm asking because when I pair the headset with my iPod, the new voice notes app says I don't have any mic.
In case it can't be done, can I use my headset with an added mic, connected to the audio plug in in the touch? I referring to something like this:
http://cgi.ebay.com/Mini-Microphone-Recorder-for-iPhone-3G-iPod-Touch-2GW0QQitemZ160344260167QQcmdZViewItemQQptZPDA_Accessories?hash=item2555433e47&_trk sid=p3286.c0.m14#ht_2801wt1165
Thanks!

No.
Create a new ID for her:
On here iPod go to
- Settings>Messages>Send and receive and sign out your ID and sign into hers. Make sure that only her ID email address is listed.
- Settings>FaceTime sign out of your ID and sign into hers hers. Make sure that under You can be reached at only her ID email address is listed
- Settings>iCloud and sign out and sign in with hers
- Setings>iTunes and App Store and sign out yur ID and sign into hers.
- Apps are locked to the account that purchased them.
- To update apps you have to sign into the account that purchased the apps. If you have apps that need updating purchased from more than one account you have to update them one at a time until the remaining apps were purchased from one account.

My ipod warranty ran out a few months ago I have a nano 5th gen. The problem is that if I want to play a song it would show the album artwork for about 3 seconds and go back to the main menu with no music playing. It'snot the head phones or ear jack. help

My ipod warranty ran out a few months ago I have a nano 5th gen. The problem is that if I want to play a song it would show the album artwork for about 3 seconds and go back to the main menu with no music playing. It'snot the head phones or ear jack. Please I Need Help

See this Troubleshooting Assistant
http://www.apple.com/support/ipod/five_rs/nano5gen/
Reset
How to reset iPod

When I play video clips from websites like Prescreen the sound is loud enough to hear w/out headphones. When I play my own professionally mastered video I have to wear head phones to hear loud enough. Is there a trick in Compressor or other software?

When I play video clips from websites like Prescreen the sound is loud enough to hear w/out headphones. When I play my own professionally mastered video I have to wear head phones to hear them loud enough. Is there a trick in Compressor or other software to make my overall sound loud enough?

The Nokia 3720 classic is a IP54 level water,
Not even close to good enough, LCD screen will crack, water will go in through the jack/charger ports..
The phone i describe has no external ports just 4-5 little pins which can't let water in or out of the device, the docking station will connect via these 4 - 5 pins for data transfer and recharging...., IPX8 standard, all the electronics are epxoyed with a glue to stop real bad shocks from drops and bangs, along with a silicon case and all the other preventative meausres means this little phone is going to outlive you.
in combination with heart rate external bluetooth connection, really what more could you want... only the Sonim comes close in terms of perfection but if it managed to pack all of above, then it would be simply wow... I don't think there's enough people who work for nokia who actually go camping, backpacking, hiking, i'm pretty sure that if i told them one day
on a holiday you might drop your phone into the swimming pool, ok fine it's a mistake but damn, there goes your $$$$ N7 or N900 or even a HTC or Iphone.... not this, you'd yell to the first person you see in the pool, hey mate can i have my phone back, don't worry about the water damage, i'll get it back on insurance after a small lie stopping the person from running off with it (in fear of the now useless mobile phoned killed by water, making an attempt to steal be useless)
The person gets their phone back and carries on about his day, it drops out of your pocket, how many times you ran over it because you happened to leave it behind the back tire. oh no i ran over my phone, the tough casing and the epoxy keeping it nice and safe, except for superficial damage cosmetic, the screen and phone should be working still able to make that call or send out GPS info....
Sorry nothing comes close by any company (except Sonim) in terms of what they can do... maybe even a portable charger turn it to recharge like on LED dynamos. nah maybe not.

Need bluetooth stereo head phones

Similar Messages

Maybe you are looking for