Need challenge response for old 1020 router.

Hello,
A colleague of mine has an old 1020 async router.
Needs to do password recovery per below Cisco doc.
Complete these steps in order to recover a password:
From the console, log in to the Cisco 1020 Router with user name enable and password override.
Note: If the enable password is not set, press Return at the password prompt.
The 1020 prints a challenge.
Provide the support representative with the challenge information.
The challenge is used to provide the response.
On the Cisco 1020 console, log in with user name enable and password response.
You are now in enable mode.
Here is the 1020 challenge = MOHOLPBMECCLFBSS
Could anyone provide the challenge response needed to access enable mode?
Thank You.

I think you're out of luck with this, cisco does not support these anymore.

Similar Messages

Need BIOS password for old ACS SE

We recently upgraded our ACS SE 1112 to a SE 1113 model. The trade allows us to keep the old hardware. I want to use it for a test Windows or Linux server, however I can't seem to be able to break out of the locked-down Windows boot sequence. Occasionally I am able to press enough keys to get what looks like a BIOS password prompt. Does anyone know what that is?

Thanks for the suggestion. I get challenged with 3 password prompts when I hit F12 during the boot sequence and neither password works. In fact, I'm not sure that is the BIOS password. But I did open a TAC case and they suggested removing the CMOS battery....which worked. Here's the sequence if I had to do it all over again:
1) boot with a diskette to find a utility to remove the master boot record. I used a 3x diskette OS/2 and used FDISK.
2) remove the cover. Take out the CMOS battery. Wait a minute or two and put it back in place.
3) reboot. Do not (yet) select F1 to setup the BIOS. Just hit the prompt to continue booting. The default boot sequence will boot from the CD.
4) Install your OS from the CD. During the install process if the box needs to reboot, do not (yet) hit F1.
5) after installation of the OS, at the next reboot, select F1 at the prompt, set up the BIOS (date/time, etc), exit and save.
It must have something to do with the SATA drive/controller and the IDE controller on the system board - but I could not find the correct BIOS settings to allow me to boot from CD if I pressed F1 after removing the CMOS battery and saved the BIOS configuration.

Elementary question: need wireless card for old Dell

Hi, all: I need to buy a wireless card for my several-years-old Dell Precision 340 desktop, so that I can network it with my MacBook Pro and printer using AirPort Express. Can buy any old USB network adapter card branded "universal"? Any recommendations? There is no built-in wireless card. Also, I understand that I will have to reconfigure the AirPort somehow to handle both PC and Mac (I spent a long time on the phone with Support getting to work in the first place, just with the Mac notebook).
Thanks for any advice!

Hello jonnofor. Welcome to the Apple Discussions!
Can buy any old USB network adapter card branded "universal"? Any recommendations? There is no built-in wireless card.
Just about any 802.11b/g wireless device will work with the AirPort Express Base Station (AX). The AX is capable of up to WPA2 wireless encryption, so if this is important to you, you would want a device that is WPA or WPA2 capable as well. In addition to USB-style, the Precision 340 can also take PCI-cards. For example, Linksys offers both a USB & PCI types.
Also, I understand that I will have to reconfigure the AirPort somehow to handle both PC and Mac
There shouldn't be any required configuration changes necessary for the AX just to support both Macs and PCs. Most issues that come into play relate to using WEP for wireless encryption. You can eliminate this by using WPA or WPA2 instead.

Need new cable for old Zen N

I lost the cable for a Zen Nano (not a Nano Plus.)
Do I need to buy a replacement from Creative? Or can I get a generic cable somewhere, and if so, what type of cable is it's Thanks.

it's a standard USB A to mini-B cable.

Need Power Cord For Old Nomad Jukebox, PLE

I need the a.c power cord, it is a 9v cord and I can really use one, Any help ?
Please email if you have one, THANKS !!

i think that will be pretty hard to come by.
try ebay you may be able to get one.
but if you cant...
go out and get yourself a REGULATED multivoltage power supply.
you know, those battery elimators with the 8 or so interchangeable plugs.
if its not regulated you run the risk of putting too much power into your jukebox.
just make sure it has a plug that fits your jukebox and you match up the polarity then your set.
go for something with at least a amp output however.
go for more then that if you can...
good luck

Using old Sky router as Access Point

Hello, I am new to the forum so I hope have posted correctly. Having recently moved house I have switched to BT from Sky and have been supplied with the HH5 and the Infinity package. Due to house lay out wifi signal is not great throughout. I am wanting to use my old Sky (Sagem 2504n, I think) router as an access point. Is this possible or would need to flash the old sky router in order to do this. My first attempt did not work (when I try to set ip in sky router to within HH range I get an error message). Basically it would be good to know if I need to flash the firmware or if it is possible to do with the sky router as is before I aware too much more time.. Any help much appreciated!
Thanks
Solved!
Go to Solution.

You should be able to use it as a wired access point provided you change the IP address, and disable DHCP.
This guide, for a Voyager router, should give you some idea of the settings to use.
Using an old BT Voyager modem as an additional wireless access point.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

I just created an iCloud email and I want to use that email for my iTunes account as well. I need help suiting the old apple I'd because I do not remember anything associated with that email and I don't know the security questions

I just created an iCloud email and I want to use that email for my iTunes account as well. I need help switching the old apple ID because I do not remember anything associated with that email and I don't know the security questions or the login for that old email.

You cannot do that. The AppleID you used to create the iCloud account is an active primary email address. The email address you created with the iCloud account is also an active primary email address (all Apple domain email address automatically become AppleIDs as well). You cannot replace the primary email address on one active AppleID with the primary email address on another, active AppleID.
You can use your iCloud email/AppleID with iTunes, but it will be a separate account, so all your previous purchases remain tied to the other AppleID you have.
I don't understand your statement that you could not remeber your old AppleID password, as you would have had to use it to create the iCloud account in the first place (the first step of creating the iCloud account required you to login with your existing AppleID and password)?

How to up the timeout setting to solve password reset portal error "Authentication gate timed out waiting for a challenge response"?

Hi Everyone,
We have the password portal up and running on one box and another server with FIM R2 and SharePoint 2010. All is good with the exception that our end users typically get distracted during the password registration and/or reset process and receive:
"An error has occurred. Please try again, and if the problem persists, contact your help desk or system administrator. (Error 3000) ". The timeout kicks in after 5 minutes of inactivity in the browser.
The FIM Service log shows the following:
"Authentication gate timed out waiting for a challenge response".
I have confirmed that the default password portal web.config setting is <add key="SessionTimeoutInMinutes" value="20" />.
We have also updated Microsoft.ResourceManagement.Service.exe.config per this
article to the following but with no luck:
<resourceManagementClient resourceManagementServiceBaseAddress="myAddress" timeoutInMilliseconds="600000" />
<resourceManagementService externalHostName="myHost" dataReadTimeoutInSeconds="600" dataWriteTimeoutInSeconds="600"/>
We did not update the Windows SharePoint Servicesweb.config setting per the article about since we are on SharePoint 2010.
There is no NLB or firewall in front on this server.
If anyone has any solution to how to solve this on FIM R2/SharePoint 2010 please let me know.
Cheers!

FIM_Admin,
You could try changing the receiveTimeoutInSeconds parameter of the resourceManagementService node in your Microsoft.ResourceManagement.Service.exe.config file. However, you are warned not to do this unless instructed to by MS customer support.
http://msdn.microsoft.com/en-us/library/windows/desktop/ee652424(v=vs.100).aspx
http://technet.microsoft.com/en-us/library/ff800821(v=ws.10).aspx

Hi, i have a new number and I'm trying to activate iMessage but i can't. it is only saying waiting for activation, i have tried a lot of times with not success. i'm not sure if i need to replace the old one to this new one, or what do do. can you help

Hi, i have a new number and I'm trying to activate iMessage but i can't. it is only saying waiting for activation, i have tried a lot of times with not success. i'm not sure if i need to replace the old one to this new one, or what do do. can you help

Troubleshooting iMessage activation:
http://support.apple.com/kb/TS4268

I have a hard drive for CD storage that needs to connect to the Ethernet router. sInce my router is not in this room, and in another room, I want to use my Mac as a router for the drive, and share the wifi. Ho do I do this

I have a hard drive for CD storage that needs to connect to the Ethernet router. sInce my router is not in this room, and in another room, I want to use my Mac as a router for the drive, and share the wifi. Ho do I do this? I gace tried the System Preferences -> Sharing, shared internet to Ethernet, but can't se ethe device on Finder

Djembe wrote:
UEFI (unified extensible firmware interface) boot requires Global unique identifier Partition Table (GPT) as opposed to the older Master Boot Record (MBR). If your existing drive is formatted in MBR, you will need to adjust BIOS settings to enable legacy boot in order for it to work properly.
Is there a performance difference between GPT and MBR? If GPT is better, I do not mind formatting the drive with it.
5. No special drivers are needed.
Thanks. What about the thunderbolt port?
7. I think Lenovo estimates 6 hours.
Lenovo says 6 hours with the 6-cell battery on its website.
BrendaEM wrote:
Hi,
There was a serious BIOS/UEFI problem with that SSD . Perhaps this thread will save you some headaches. Someone is recomending shutting off Rapid Boot in the setup, which would probable mean little with a SSD, anyway.
I read through this, and it looks like the problem was fixed in a BIOS update, which I plan to do. However, it also seems like Intel Rapid Start is not even worth it in the first place, as sleep consumes almost no power at all.
W540: i7-4700mq, K2100m, 8 GB DDR3L, 512 GB SSD
T510: i7-620m, NVS 3100m, 8 GB DDR3, 512 GB SSD

Do I still need to use the old mobile me backup system for backing up a mac desktop and if I delete it will it affect the memory of my system which has now Maverics

Do I still need to use the old mobile me backup system for backing up all my data and having it able to get at in case of a crash, or can the icloud reset everything? Because I can not find any structured refrence, as to how it would be done. I am updated to Maverics. Also does the icloud continue if I uninstall the backup to free up space?

MobileMe was discontinued in 2012 and all the data stored on it was deleted, and iCloud can't make backups of Macs.
What I recommend you to make backups is to get an external drive and use Time Machine or an application like Carbon Copy Cloner. With this, you can access to your data everywhere and safely, and then, if you want, use a cloud storage service like CrashPlan. You can keep on using iCloud without backups

Hello, had to move to mavericks lost quicktime Pro, Need the feature for looping audio sections repeatedly, I have the install Key from my old QT Pro version, any ideas?

Hello, had to move to mavericks lost quicktime Pro, Need the feature for looping audio sections repeatedly, I have the install Key from my old QT Pro version, any ideas?

If QuickTime Player 7 isn't in the Utilities folder automatically, you can install it separately. See:
http://support.apple.com/kb/HT3678
Instructions on how to register your QuickTime Pro key can be found in that same document.
Regards.

Could not get response for challenge?

I could succefully use podcast capture to post video to groupblog.
But when I used command line "pcastaction groupblog", it always said that
"ERROR: could not get response for challenge"
But "pcast_post2groupblog" works well for me. I wonder why this happened?
P.S:
I've updated my server to the latest version.

If you look at the workflow, there is probably something in there like this:
<string>--otp=##Groups Administrator Username:Groups Administrator Password##</string>
That's a one time pad. I ran into this when troubleshooting our iTunes U workflow from the command line. To get my iTunes U stuff to work from the command line I had to generate a OTP each time, like so:
$sudo pcastconfig --add_access "token" --properties "iTunes U Shared Secret"
Except yours will be different because it's for group blog.... if indeed this is your problem. I only guessed this looking at the stock blog workflow, it uses an OTP.
Hope that was helpful and not way off the mark.

Need to select all equipments (PRT) for a plan (routing) operation (PLPO)

hi,
I need to select all assigned equipments (PRT) for a plan (routing) operation (PLPO).
Can anybody tell me the database table relation or is there a function module or a BAPI or something like this !?
Thanks
Olaf
Edited by: Olaf Krüger on Feb 20, 2008 12:03 PM: BADI to BAPI

I suppose you have every PLPO needed (else look at function module WOSTS_TASKLIST_READ_FROM_DB)
Then read
PLMZ Allocation of bill of material items to operations
STPO BOM item
SELECT * FROM plmz INTO TABLE t_plmz
    FOR ALL ENTRIES IN t_plpo
    WHERE plnty = t_plpo-plnty
      AND plnnr = t_plpo-plnnr
      AND plnkn = t_plpo-plnkn.
SELECT * FROM stpo INTO TABLE t_stpo
    FOR ALL ENTRIES IN t_plmz
    WHERE stlty = t_plmz-stlty
      AND stlnr = t_plmz-stlnr
      AND stlkn = t_plmz-stlkn.
Regards

I need a floppy disk drive for old 3 1/2" disks. I have a PowerBook G4 Mac with MacOS X 10.4 operating system. What will work for me?

I need a floppy disk drive for old 3 1/2" disks. I have a PowerBook G4 with Mac OS X 10.4 operating system. What external drive will for for me?

Hi,
Providing that the old 3.5" floppies are 1.44 MB HD disks, you should be able to use a USB floppy drive.
However, if the disks are 2DD/DSDD in the 800K Mac format a USB drive is not going to work. In this case you would need a suitable semi-old Macintosh computer with a built-in floppy drive as an intermediary.
Jan

Need challenge response for old 1020 router.

Similar Messages

Maybe you are looking for