Need configuration help on producing dial tone

Hello Experts,
I have a Cisco 2921 router with VWIC3-2MFT-T1/E1 card. On this card we have T1-CAS digital line connected. We have been provided with a set of DID numbers. We have a requirement where, when we dial a DID, the router should provide a dial tone, and should allow the user to dial to extension numbers. Not sure if this is feasible. If at all possible, will need to some configuration help.
Thanks
Arabinda

Sure it's possible. What's the T1 connected to? The router will offer two-stage dialing (aka dial tone) when the incoming POTS dial-peer does not have the 'direct-inward-dial' command on it. The router will accept any input and search for an outbound dial-peer (or ephone-dn for locally registered DNs) to match. Be careful if the T1 is connected to the PSTN as this is a toll fraud risk. You need to use CoR to reign in what outbound dial-peers are available to it.
Dial Peer Basics:
http://www.cisco.com/en/US/tech/tk652/tk90/technologies_tech_note09186a008010ae1c.shtml
Class of Restrictions:
http://www.cisco.com/en/US/tech/tk652/tk90/technologies_configuration_example09186a008019d649.shtml
Please remember to rate helpful responses and identify helpful or correct answers.

Similar Messages

How can I make the E7 to produce dial-tones when c...

Of course, I can hear the DTMF dial tones when I dial the number from the touch screen.
But, I need the E7 to send dial tones when I call a contact (hence I don't dial from the touch screen). I need that because I'm using a calling card which needs the dial tones to be sent.
It works like this:
In the contact details I enter a long number, with pauses, like:
18001231234p09876543p011392109876
where the 1st numer calls the calling-card number, the 2nd is the pin, the 3rd is the international number I'm calling.
Of corse, when I call that long number (which is a contact) the carrier needs to "hear" the dial tones.
Hence, the question in the subject line.
P.S. If there is a better way to use calling cards, pls let me know.

I think I was wrong. After trial and re-trials I see the E7 actually sends out the dial tones.
Well, I don't know why it did not work at first. Now it's ok.

Debugging - need configuration help

I also posted this in Advanced Techniques by accident...
I need some help configuring my local development machine for CFBuilder debugging. CF application development is configured correctly, but I'm having problems configuring debugging settings for CFBuilder/Eclipse. CFBuilder is installed and connected to RDS, and the CF Administrator is setup to do line level debugging. I'm running Windows 7 x64 with ColdFusion 9 (using IIS).
All my projects are in my "C:\Dev" folder, and each project contains a "www" folder, which is the web root for the project. So I've got my projects organized like this:
C:\Dev
     TestSite
          design
          docs
          www <--- web root folder
I've created a ColdFusion project and mapped it directly to the "www" root folder. In IIS, the web root folder is mapped via a virtual directory under the default web site, and is accessed from "http://127.0.0.1/testsite"
I configured my RDS Server, which works correctly, so I can see the databases on the server. Nice. I also setup a server in the servers list in the coldfusion perspective and imported the settings directly from my RDS server. This one has the same name as my RDS server, which is "Local RDS Server." I also added a URL Prefix for "testsite" that is mapped to the local path: (C:\Dev\TestSite\www) and "http:\\127.0.0.1\testsite. And finally, in the Debug Mappings (preferences window), I specified "Local RDS Server."
Everything seems to be setup, but I still cannot debug. Here's what happens:
From the ColdFusion perspective, I right click on index.cfm and select "Debug As -> ColdFusion Application" The first time I do this, it switches over to the ColdFusion Debugging Perspective and loads "http://homepage/" and then nothing seems to work. In the Debug tab, it shows me that it created a new launch for my project as follows:
TestSite
     Local RDS Server
          ColdFusion Template
I can see my breakpoint in my breakpoints tab. But I can't seem to get any farther. I can't find a way to run to my breakpoint.The home page for the active debugging session is "http://homepage/" which is something that I don't understand. How do I make CFBuilder go to the correct home page for the debugging session? That might be the key.

My previous post had to do with migrating an eclipse project over to a coldfusion project... that was my first one. I was finally able to get running under the debugger. Very nice!! I'm so happy to have a debugger available now!!!!
I just started setting up my next project, but I'm stumped. When I right-click on this new project, and I go to properties, and then click on my ColdFusion Server Settings pane, I want to be able to specify the address to use for debugging, which I would assume should be in the "Sample URL" field. But the field is disabled and it says "Sample URL is not available. (Project is not in document root of server Local RDS Server).
Local RDS Server is the local RDS server I setup, but I see where I specify a document root for the RDS server... I just specify a Host Name, which is my local IP address for my projects.
Any ideas?

Please help - suddenly no dial tone

I would really appreciate any help please.
I just arrived home last night after being away for a few weeks on holiday. My phone and DSL (not with BT) were working fine when I went away, but now I do not get a dial tone.
My phone is a cordless one, so it was unplugged while I was gone, but I don't know if this would have caused any issues.
My internet still works fine, no problems there.
In an effort to solve this I have done the following:
1/ Unplgged everything from my one and only phone socket including DLS filter etc. I then just plugged in my phone, still no dialtone, so I tried another spare phone I have, again no dialtone.
2/ Then I removed the faceplate to the socket and triend both phones again in the test socket, still no dial tone.
What is weird is that if I ring my phone on my mobile, the phones will ring, but picking them up does not answer them, and no sound is transmitted along the line.
3/ I ran the online line test on the line and it came back saying there were no issues.
4/I spoke to someone at BT and have arranged for an engineer to come out next week, but obviously, does anyone here have any more suggestions of solutions as I literally cannot afford the rediculously expensive call out fee of £127 if there is something else I could have done.
I live in an apartment building, and no one else is having issues with their phone. The phone box for the building is located at the top of a piller in the back yard easily 4-5m off the ground.
Any help?

As long as you have tried a working phone into the test socket and still getting no dial tone, you have done enough checking.... sounds like a one leg dis/ HR fault, this can knock out your phone line, but your broadband can still work.... just wait for the engineer...you can try and get your incoming calls diverted to your mobile free of charge while you wait... hope this helps

Cluster,FileServlet and images - need configuration help

Hi All.
We're using 2 wl5.1sp9 as "proxies" and 2 wlcs3.2 as the application server.
We'd set the default servlet to be the cluster servlet
(weblogic.httpd.defaultServlet=cluster
weblogic.httpd.register.cluster=\
weblogic.servlet.internal.HttpClusterServlet
weblogic.httpd.initArgs.cluster=\
defaultServers=10.5.195.31:80:443|10.5.195.30:80:443,\
DebugConfigInfo=ON)
where these IP's are the application servers internal IPs.
Now, we wanted to serve the static files (images, html, js) from the wl
servers.
For our surprise, just putting the files on the wl servers was NOT doing the
job!
(We believed that the cluster first searches locally and only after that
looks on other hosts)
So we registered the images by file type
(weblogic.httpd.register.*.gif=weblogic.servlet.FileServlet
weblogic.httpd.register.*.jpg=weblogic.servlet.FileServlet)
Now, if we got images that are on the application servers, we can't get
these files!
Could someone please help how to set this configuration correctly?

Hi.
Please try posting this on weblogic.developer.interest.servlet or
weblogic.developer.interest.clustering.
Thanks,
Michael
"R@nsh!" wrote:
Hi All.
We're using 2 wl5.1sp9 as "proxies" and 2 wlcs3.2 as the application server.
We'd set the default servlet to be the cluster servlet
(weblogic.httpd.defaultServlet=cluster
weblogic.httpd.register.cluster=\
weblogic.servlet.internal.HttpClusterServlet
weblogic.httpd.initArgs.cluster=\
defaultServers=10.5.195.31:80:443|10.5.195.30:80:443,\
DebugConfigInfo=ON)
where these IP's are the application servers internal IPs.
Now, we wanted to serve the static files (images, html, js) from the wl
servers.
For our surprise, just putting the files on the wl servers was NOT doing the
job!
(We believed that the cluster first searches locally and only after that
looks on other hosts)
So we registered the images by file type
(weblogic.httpd.register.*.gif=weblogic.servlet.FileServlet
weblogic.httpd.register.*.jpg=weblogic.servlet.FileServlet)
Now, if we got images that are on the application servers, we can't get
these files!
Could someone please help how to set this configuration correctly?--
Developer Relations Engineer
BEA Support

Need Help with iMac G4 No Dial Tone

I am working on a friend's iMac G4 800 Mhz. Has Mac X 10.2.3 OS. Internal Apple 56K V.90 Modem.
The modem gives error "no dial tone". This just recently started happening for no apparent reason. Tried different phone cable and tested the wall jack for dial tone on a connected phone. All tests OK.
This modem is "built in". Is this problem fixable? Is it a hardware or a settings issue?
The only fix I can think of is an external modem, but would like to fix the internal one if possible.
Any ideas? Any and all advice is appreciated. I'm new to Macs, so I have limited knowledge of the system.
Thanks,
Jim
iMac G4 Mac OS X (10.2.x)

Hello,Try going Apple Menu > System Preferences... > Network > Show: Internal Modem > Modem tab > uncheck the wait for dialling tone option.
Does that solve it?
mrtotes

1941W configuration help needed

Our Deployment Scenario:-
1941W Gigabit Ethernet 0/0 is connected to the PPOE connection of the ISP.
Gigabit Ethernet 0/1 is connected to the wired LAN
I have created 2 wireless radio Cisco_Kamran_BGN which is operating at 2.4 Ghz Devices and Cisco_Kamran_A which is operating at 5Ghz Devices.
I have created 2 VLans for the Wireless.
Vlan 10 for Cisco_Kamran_A        192.168.10.x
Vlan 11 for Cisco _Kamran_BGN   192.168.11.X
The problem is the Wireless users are not getting the IP address from the respective DHCP server which has been configured on the Router.
Can please any from the community help me and show me where I am missing the configuration.
Please find my router & ap configuration below.
Router Configuration
Router#
sh run
Building configuration...
Current configuration : 3022 bytes
! No configuration change since last restart
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
enable secret 5 $1$TdQt$npYeaf/W0kRElcfMggzJ31
no aaa new-model
service-module wlan-ap 0 bootimage autonomous
no ipv6 cef
ip source-route
ip cef
ip dhcp excluded-address 192.168.1.1 192.168.1.50
ip dhcp excluded-address 192.168.10.1 192.168.10.10
ip dhcp excluded-address 192.168.11.1 192.168.11.10
ip dhcp pool DHCP
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 195.229.241.222 213.42.20.20
ip dhcp pool Cisco_Kamran_A
network 192.168.11.0 255.255.255.0
default-router 192.168.11.1
dns-server 195.229.241.222 213.42.20.20
ip dhcp pool Cisco_Kamran_BGN
network 192.168.10.0 255.255.255.0
default-router 192.168.10.1
dns-server 195.225.241.222 213.42.20.20
multilink bundle-name authenticated
crypto pki token default removal timeout 0
license udi pid CISCO1941W-E/K9 sn FCZ1553C1VK
hw-module ism 0
redundancy
bridge irb
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
interface wlan-ap0
description Service module interface to manage the embedded AP
ip unnumbered GigabitEthernet0/0
arp timeout 0
no mop enabled
no mop sysid
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
interface Wlan-GigabitEthernet0/0
description Internal switch interface connecting to the embedded AP
switchport mode trunk
no ip address
interface Vlan1
no ip address
interface Vlan10
ip address 192.168.10.1 255.255.255.0
ip access-group DSL_ACCESSLIST in
ip nat inside
ip virtual-reassembly in
interface Vlan11
ip address 192.168.11.1 255.255.255.0
ip access-group DSL_ACCESSLIST in
ip nat inside
ip virtual-reassembly in
interface Dialer1
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
ppp authentication pap callin
ppp pap sent-username xxxxxx password 0 xxxxxx
ppp ipcp route default
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list DSL_ACCESSLIST interface Dialer1 overload
ip access-list extended DSL_ACCESSLIST
permit ip 192.168.0.0 0.0.255.255 any
control-plane
line con 0
password xxxxxx
login
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line 67
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
password xxxxxx
login
transport input all
scheduler allocate 20000 1000
end
Router#
Router#
Router#
Access Point Configuration
ap#
ap#
ap#
sh run
Building configuration...
Current configuration : 2603 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap
enable secret 5 $1$JxdQ$a2/00bWJuhUKP9QLC94YD/
no aaa new-model
dot11 syslog
dot11 ssid Cisco_Kamran_A
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 7 1045081417161C5A555C7A7B
dot11 ssid Cisco_Kamran_BGN
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 7 020D05561907017015165949
username Cisco password 7 14341B180F0B
bridge irb
interface Dot11Radio0
description 802.11bgn radio
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
broadcast-key change 3600
ssid Cisco_Kamran_BGN
antenna gain 0
station-role root
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface Dot11Radio1
description 802.11a radio
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
ssid Cisco_Kamran_A
antenna gain 0
no dfs band block
channel dfs
station-role root
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface GigabitEthernet0
description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router
no ip address
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface GigabitEthernet0.10
description 802.11a bridge
encapsulation dot1Q 10
no ip route-cache
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface GigabitEthernet0.11
description 802.11bgn bridge
encapsulation dot1Q 11
no ip route-cache
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface BVI1
ip address dhcp client-id GigabitEthernet0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
no activation-character
line vty 0 4
login local
end
ap#
ap#
ap#

Hi Stepehen,
Did the configuration as per your advice but i am getting the below mentioned error which i have highlighted it in red. Please advice what needs to be done.
Home
Re: 1941W configuration help needed
created by Stephen Rodriguez in Getting     Started with Wireless - View the full discussion
conf t
interface     Dot11Radio0
no ssid     Cisco_Kamran_BGN
no encryption mode     ciphers aes-ccm
exit
interface     Dot11Radio1
no encryption mode     ciphers aes-ccm
no ssid     Cisco_Kamran_A
exit
dot11 ssid     Cisco_Kamran_A
vlan 10
dot11 ssid     Cisco_Kamran_BGN
vlan 11
exit
interface     Dot11Radio0
encryption vlan 11     mode ciphers aes
ssid     Cisco_Kamran_BGN
exit
interface     dot11radio0.1
encapsulation     dot1q 1 native
bridge-group 1
interface     dot11radio 0.11
encapsulation     dot1q 11
bridge-group 11
Configuration of     subinterfaces and main interface
within the same bridge     group is not permitted
exit
interface     Dot11Radio1
encryption vlan 10     mode ciphers aes-ccm
ssid     Cisco_Kamran_A
interface     dot11radio1.1
encapsulation     dot1q 1 native
bridge-group 1
interface     dot11radio1.10
encapuslation     dot1q 10
bridge-group 10
Configuration of subinterfaces and main     interface
within the same bridge     group is not permitted
end
wr
Reply to this message by going to Home
Start a new discussion in Getting Started with Wireless at Home

Need some Help configuring sip

Hi all ! ,
Im kind off new to sip calling and cisco telephony , but here goes ,: i have a 2821 router with CME installed
IOS : C2800NM-IPVOICEK9-M
Sofware version : 15.1(4)M4 / CME 8.6
Attached to GE0/0 is a CISCO 3750 switch
GEO - consisfts of 3 VLANS , the native
172.22.1.X
172.22.100.X VOICE
172.22.101.X DATA
my tftpserver = 172.22.1.150
i need some help configuring a sip trunk , i have 10 testing phonenumbers from vodafone , but i do not know where to start to get this working
i have tried
http://www.cisco.com/en/US/products/sw/voicesw/ps4625/products_configuration_example09186a00808f9666.shtml
but im getting stuck with what to fill in where .. is there anyone form NL whom has the same setup ? or similar ? or can give me some guidance on how to make the test calls

ok.. here goes
Building configuration...
Current configuration : 9721 bytes
! Last configuration change at 15:26:14 CET Thu Jan 2 2014
! NVRAM config last updated at 15:26:14 CET Thu Jan 2 2014
! NVRAM config last updated at 15:26:14 CET Thu Jan 2 2014
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
no aaa new-model
clock timezone CET 1 0
network-clock-participate wic 0
network-clock-participate wic 1
network-clock-select 1 E1 0/0/0
network-clock-select 2 E1 0/0/1
dot11 syslog
ip source-route
ip cef
ip dhcp pool VOICE
network 172.22.100.0 255.255.255.0
option 150 ip 172.22.1.150
default-router 172.22.100.1
ip dhcp pool DATA
network 172.22.101.0 255.255.255.0
default-router 172.22.101.1
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
isdn switch-type primary-net5
voice service voip
ip address trusted list
ipv4 172.22.1.50
ipv4 172.22.1.51
ipv4 172.22.100.1
ipv4 172.22.101.1
ipv4 62.140.159.225
callmonitor
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
sip
registrar server expires max 3600 min 3600
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
codec preference 4 g729br8
voice register global
voice translation-rule 1
rule 1 /5123781291/ /601/
rule 2 /5123781290/ /600/
voice translation-rule 2
rule 1 /^112$/ /112/
voice translation-rule 3
rule 1 /^.*/ /0262610290/
voice translation-rule 4
rule 2 /600/ /5123788000/
rule 3 /601/ /5123788001/
rule 4 /^2(..)$/ /51237812\1/
voice translation-profile CUE_Voicemail/AutoAttendant
translate called 1
voice translation-profile PSTN_CallForwarding
translate redirect-target 4
translate redirect-called 4
voice translation-profile PSTN_Outgoing
translate calling 3
translate called 2
translate redirect-target 4
translate redirect-called 4
voice-card 0
crypto pki token default removal timeout 0
controller E1 0/0/0
framing NO-CRC4
pri-group timeslots 1-31
controller E1 0/0/1
framing NO-CRC4
pri-group timeslots 1-31
ip ftp username cisco
ip ftp password cisco123
ip tftp source-interface GigabitEthernet0/0.1
interface GigabitEthernet0/0
no ip address
duplex auto
speed auto
no keepalive
interface GigabitEthernet0/0.1
encapsulation dot1Q 1 native
ip address 172.22.1.51 255.255.255.0
interface GigabitEthernet0/0.20
encapsulation dot1Q 20
ip address 172.22.101.1 255.255.255.0
interface GigabitEthernet0/0.100
encapsulation dot1Q 100
ip address 172.22.100.1 255.255.255.0
interface GigabitEthernet0/1
no ip address
shutdown
duplex full
speed 100
interface Serial0/0/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
interface Serial0/0/1:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
interface BRI0/1/0
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
interface BRI0/1/1
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
ip forward-protocol nd
ip http server
ip http authentication local
no ip http secure-server
ip http max-connections 16
ip http path flash:gui
ip route 0.0.0.0 0.0.0.0 172.22.1.50
tftp-server flash:7941/apps41.8-4-1-23.sbn alias apps41.8-4-1-23.sbn
tftp-server flash:7941/cnu41.8-4-1-23.sbn alias cnu41.8-4-1-23.sbn
tftp-server flash:7941/dsp41.8-4-1-23.sbn alias dsp41.8-4-1-23.sbn
tftp-server flash:7941/jar41sccp.8-4-1-23.sbn alias jar41sccp.8-4-1-23.sbn
tftp-server flash:7941/cvm41sccp.8-4-1-23.sbn alias cvm41sccp.8-4-1-23.sbn
tftp-server flash:7941/SCCP41.8-4-2S.loads alias SCCP41.8-4-2S.loads
tftp-server flash:7941/term41.default.loads alias term41.default.loads
tftp-server debug
control-plane
voice-port 0/0/0:15
voice-port 0/1/0
voice-port 0/1/1
voice-port 0/0/1:15
voice-port 2/0/0
voice-port 2/0/1
voice-port 2/0/2
voice-port 2/0/3
voice-port 2/0/4
voice-port 2/0/5
voice-port 2/0/6
voice-port 2/0/7
voice-port 2/0/8
voice-port 2/0/9
voice-port 2/0/10
voice-port 2/0/11
voice-port 2/0/12
voice-port 2/0/13
voice-port 2/0/14
voice-port 2/0/15
voice-port 2/0/16
voice-port 2/0/17
voice-port 2/0/18
voice-port 2/0/19
voice-port 2/0/20
voice-port 2/0/21
voice-port 2/0/22
voice-port 2/0/23
mgcp profile default
dial-peer voice 1 voip
description **Incomming Call from SIP Trunk**
translation-profile incoming CUE_Voicemail/AutoAttendant
session protocol sipv2
session target ipv4:172.22.1.50
incoming called-number .%
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
no vad
dial-peer voice 2 voip
description **Outgoing Call to SIP Trunk**
translation-profile outgoing PSTN_Outgoing
destination-pattern 9........
session protocol sipv2
session target ipv4:172.22.1.50
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
no vad
dial-peer voice 3 voip
description **Outgoing Call to SIP Trunk **
translation-profile outgoing PSTN_Outgoing
destination-pattern 9[2-9]..[2-9]......
session protocol sipv2
session target ipv4:172.22.1.50
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
no vad
dial-peer voice 4 voip
description **Outgoing Call to SIP Trunk**
translation-profile outgoing PSTN_Outgoing
destination-pattern 9[0-1][2-9]..[2-9]......
session protocol sipv2
session target ipv4:172.22.1.50
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
no vad
dial-peer voice 5 voip
description **911 Outgoing Call to SIP trunk**
translation-profile outgoing PSTN_Outgoing
destination-pattern 911
session protocol sipv2
session target ipv4:172.22.1.50
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
no vad
dial-peer voice 6 voip
description **Emergency Outgoing Call to SIP Trunk**
translation-profile outgoing PSTN_Outgoing
destination-pattern 9911
session protocol sipv2
session target ipv4:172.22.1.50
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
no vad
dial-peer voice 7 voip
description **911/411 Outgoing Call to SIP Trunk**
translation-profile outgoing PSTN_Outgoing
destination-pattern 9[2-9]11
session protocol sipv2
session target ipv4:172.22.1.50
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
no vad
dial-peer voice 8 voip
description **International Outgoing Call to SIP Trunk**
translation-profile outgoing PSTN_Outgoing
destination-pattern 9011T
session protocol sipv2
session target ipv4:172.22.1.50
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
no vad
dial-peer voice 9 voip
description **Star Code to SIP Trunk**
destination-pattern *..
session protocol sipv2
session target ipv4:172.22.1.50
voice-class codec 1
voice-class sip dtmf-relay force rtp-nte
dtmf-relay rtp-nte
no vad
dial-peer voice 10 voip
description **CUE Voicemail**
translation-profile outgoing PSTN_CallForwarding
destination-pattern 600
b2bua
session protocol sipv2
session target ipv4:172.22.1.155
dtmf-relay sip-notify
codec g711ulaw
no vad
dial-peer voice 11 voip
description **CUE Auto Attendant**
translation-profile outgoing PSTN_CallForwarding
destination-pattern 601
b2bua
session protocol sipv2
session target ipv4:172.22.1.155
dtmf-relay sip-notify
codec g711ulaw
no vad
sip-ua
authentication username 0262610290 password 7 15020A1F173D24362C realm 62.140.1
59.225
authentication username 0262610290 password 7 021605481811003348
no remote-party-id
retry invite 2
retry register 10
timers connect 100
registrar ipv4:62.140.159.225 expires 3600
sip-server ipv4:62.140.159.224
host-registrar
telephony-service
max-ephones 58
max-dn 192
ip source-address 172.22.100.1 port 2000
calling-number initiator
system message testing
cnf-file location TFTP tftp://172.22.1.150/
load 7960-7940 P00307020200.loads
load 7941 SCCP41.8-4-2S.loads
load 7941GE SCCP41.8-4-2S
time-format 24
dialplan-pattern 1 26261029.. extension-length 3 extension-pattern 9..
voicemail 600
max-conferences 12 gain -6
call-forward pattern 9.T
moh music-on-hold.au
web admin system name admin password password
dn-webedit
time-webedit
transfer-system full-consult
secondary-dialtone 9
directory entry 1 101 name 101
create cnf-files version-stamp 7960 Jan 02 2014 08:40:49
ephone-dn 1
number 290 secondary 0262610290
name Phone 1
hold-alert 30 originator
ephone-dn 2
number 291 secondary 0262610291
name phone 2
hold-alert 30 originator
ephone-dn 3
number 292 secondary 0262610292
name Phone 3
hold-alert 30 originator
ephone-dn 4
number 293 secondary 0262610293
name Phone 4
hold-alert 30 originator
ephone-dn 5
number 294 secondary 0262610294
label Phone 5
hold-alert 30 originator
ephone 1
mac-address 0019.E88F.3BDD
button 1:1
ephone 2
mac-address 001E.4A92.0A27
type 7961
button 1:2
ephone 3
mac-address 0012.43F5.03AF
button 1:3
ephone 4
mac-address 000F.F7AC.502A
button 1:4
ephone 5
mac-address 0019.E851.090A
button 1:5
line con 0
line aux 0
line vty 0 4
login
transport input all
scheduler allocate 20000 1000
ntp master
end

Need second dial tone after dialing 9

Hello, I am trying to configure CCM so when user picks up his phone and dials 9 he is provided with a second dial tone. Usually this is a feature provided by the local PBX but I wanted to know if I can do this on the CCM.

Hi Farid,
Check your 9@ Route Patterns for this setting;
Provide Outside Dial Tone
Check this check box to provide outside dial tone. To route the call in the network, leave the check box unchecked.
From this CCM 4.1.3 doc;
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_administration_guide_chapter09186a00803ed685.html#wp1023973
Hope this helps!
Rob

No Dial Tone - Verizon seems no help

I suppose I'm venting.
I came home Friday and my phone does not have a dial tone but I still had internet access. I went through the website's troubleshooting guide on trying to disconnect and connect phones from the line. Also opening the ONT door to check the status. None helped.
I progressed to chat with Verizon agent. It turns out that Verizon turned off my phone. I was scheduled to have triple play installed (did not have TV option before) on Friday but I already rescheduled last Monday for next Thursday. Apparently Verizon turned my phone off even when the installation was rescheduled. Agent 1 said that I would need to have somebody come to the house to turn in on. I'm not available in the time they had until my rescheduled appointment. Why do they need somebody to come to the house to turn it on when it was remotely turned off? Agent 1 says he could not help me and that someone at cssc might. He transfers me to CSSC Agent 2.
Agent 2 said that my billing was fine. (So I'm paying for a dead phone.) and that he could not help me either. He told me to call the 1-888-553-1555.
Called 1-888-553-1555. Agent 3 answered. He said that he needs billings help to try to fix the issue to turn on my phone. I was transferred to Agent 4.
Agent 4 seemed to be trying to help. She said that she was in contact with some department in Verizon to see what is going on. I thought that it was being resolved. Then on one of the holds, I was transferred to the large pool of callers and had to start over again with Agent 5. Mind you, for each of these Agents, I had to start over with telephone number, address and the issues.
Agent 5 seems to be trying to help but within a short period of time, I was put back to the big pool of callers and had to start over again with Agent 6.
Agent 6 seems to be helpful. She said that they had reverse the order to turn the phone on and that I should get service soon. End of phone calls. Almost 2 hours on the internet and phone trying to get my FIOS phone working.
14 hours later. Still no dial tone. Maybe it will be back at 24 hours. Sigh.

Your issue has been escalated to a Verizon agent. Please go to your profile page for the forum, and look in the middle, right at the top where you will find an area titled "My Support Cases". You can reach your profile page by clicking on your name beside your post, or at the top left of this page underneath the title of the board. you will find a link to the private board where you and the agent may exchange information.
To ensure you know when they have responded to you, at the top of your support case there is a drop down menu for support case options. Open that and choose "subscribe".This should be checked on a frequent basis as the agent may be waiting for information from you before they can proceed with any actions. Please keep all correspondence regarding your issue in the private support portal.
If a forum member gives an answer you like, give them the Kudos they deserve. If a member gives you the answer to your question, mark the answer that solved your issue as the accepted solution.

I need help with my text tone and I have ring tone. no text tone for the 4s.

I need help with my text tone. I have ring tone no text tone. I have a 4s.

Hi Sarar2333! Let's get your text tones working again!
Here's a link with instructions how to enable and change your alert sounds for your text/notification settings on your iPhone 4S: http://vz.to/1stiF8a. You can ensure text tones are enabled by selecting a tone in the "Text Tone" setting. Let me know how that works out for you. Thanks!
AnthonyTa_VZW
Follow us on Twitter @VZWSupport

Need Flash Help - configuring AIrtight Simple Viewer Pro

I need some help configuring the Airtight Interactive simple viewer pro, which requires flash. I am a complete beginner with flash, and I am reluctant to undertake the learning curve, though I am very tech saavy.
My ideal would be to locate someone who could do this FOR me, though resources are very limited for this project. Any suggestions of where I might connect with someone interested in doing this?
Alternately, I could undertake it myself, with someone qualified to coach me rather thouroughly through the whole process. That could be offline, or here where others could benefit from the thread. If someone offers this, I will post the precise details of what I need. The project is medium challenging, not extremely complex, but more than very basic.
Many Thanks.

Hi:
When you create the simpleviewer slideshow with iPhoto's plugin there should be a folder created on your HD that contains the items seen in the screenshot below:
The folder was named simpleviewer because that's what I named it during the export from iPhoto. That's the same folder as I refer to as "Slideshow folder". It can be whatever you name it when exporting from iPhoto. Upload that folder to your iDisk/Web/Sites folder as shown below:
In the iFrame code use the following URL to the index.html file inside the simpleviewer folder:
http://web.me.com/YourMMe_AccountName/simplerviewer/index.html
That should do it.

Hard drive configuration help needed.

Just got the mac today and I'm starting the upgrades. This is how it will look. 3 1TB seagate drives. I am going to clone the factory drive to one. Install Vista through bootcamp on another.
This is what The Hatter had mentioned in another post that I started. "Vista is easy to install, doesn't need any help really, doesn't run in, under, or through BootCamp. Just format a drive as Master Boot Record, setup one or more FAT partitions (you will need to delete and create NTFS when it gets to the install screen in Vista). Then once running, you install some Apple hardware services and support to allow switching, synching time, and such. And install the latest Nvidia Vista drivers."
I can probably figure out how to get the process started, but I have no clue as to the specifics of the last sentence that starts "Then once running.....". If you see this Hatter, could you please give me the specifics? The third will be for storage.
I noticed that there are no jumpers present on the Western Digital that came with it. So is removing the limiting jumper's from the Segate's the only settings I need to worry about?
Lastly. When I install these drives, will Mac do the format or is there something I need to do first?
Thanks in advance.

You'll need to consult Seagate's configuration information for your drive model. You can locate it at Seagate's web site.
Partitioning and formatting is done using Disk Utility in the Utilities folder. New drives that did not come installed from Apple should be prepped properly as follows:
Extended Hard Drive Preparation
1. Open Disk Utility in your Utilities folder. If you need to reformat your startup volume, then you must boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger or Leopard.)
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Set the number of partitions from the dropdown menu (use 1 partition unless you wish to make more.) Click on the Options button, set the partition scheme to GUID (only required for Intel Macs) then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the volume(s) mount on the Desktop.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
The exception would be if you plan to set up one entire drive for Vista. In that case when you partition the drive select MBR partition scheme rather than GUID and format the drive MSDOS. You need not use the Write Zeros option. When you install Vista it will reformat the drive NTFS.
If you intend to use part of one drive for Vista and another partition for the Mac, then prep the drive for the Mac as outlined above. Then use Boot Camp to create the Windows partition on the drive. Boot Camp will install the MBR on the Windows partition which you cannot do from Disk Utility.

Multiple ethernet network adaptors + MySQL/php5: configuration help needed

I would be grateful if someone could give me some advice on how to configure multiple ethernet adapters under OS X 10.5.6
I have set up my system to work nicely with two ethernet network adapters, each with its own fixed IP. This bit works just fine. The machine supports two separate servers - a mail server and the OS X Apache2 server. I have configured the mail server to only listen to one of the IPs, and the Apache2 server to listen to the other (via httpd.conf). The system also has MySQL and php5 installed / enabled, and these services are only used by the Apache2 server.
The problem I have is that when I start the machine, initially the php5 system cannot connect reliably to the MySQL database system. The fix I have found is to temporarily make the ethernet adapter connected to the mail server 'inactive'. While this is so, the php5/MySQL connection to Apache2 works. Curiously, once an initial connection between php5 and MySQL has been made, subsequently I can make the mail server's ethernet adapter active again without further problems.
I initially thought this might be due to 'service order' issues - but changing the service order (e.g. putting the Apache adapter 'above' the mail adapter in the service order does not help. The fix only works by making the mail adapter inactive temporarily.
I suspect that there is some configuration change I can make to clarify the setup I have. The MySQL and Apache installations only need to talk to the Apache server - but I am not sure how to record this configuration in the OS X system.
Thanks in advance for any assistance that you can provide.
Message was edited by: Gavin Lawrie

Hi Stepehen,
Did the configuration as per your advice but i am getting the below mentioned error which i have highlighted it in red. Please advice what needs to be done.
Home
Re: 1941W configuration help needed
created by Stephen Rodriguez in Getting     Started with Wireless - View the full discussion
conf t
interface     Dot11Radio0
no ssid     Cisco_Kamran_BGN
no encryption mode     ciphers aes-ccm
exit
interface     Dot11Radio1
no encryption mode     ciphers aes-ccm
no ssid     Cisco_Kamran_A
exit
dot11 ssid     Cisco_Kamran_A
vlan 10
dot11 ssid     Cisco_Kamran_BGN
vlan 11
exit
interface     Dot11Radio0
encryption vlan 11     mode ciphers aes
ssid     Cisco_Kamran_BGN
exit
interface     dot11radio0.1
encapsulation     dot1q 1 native
bridge-group 1
interface     dot11radio 0.11
encapsulation     dot1q 11
bridge-group 11
Configuration of     subinterfaces and main interface
within the same bridge     group is not permitted
exit
interface     Dot11Radio1
encryption vlan 10     mode ciphers aes-ccm
ssid     Cisco_Kamran_A
interface     dot11radio1.1
encapsulation     dot1q 1 native
bridge-group 1
interface     dot11radio1.10
encapuslation     dot1q 10
bridge-group 10
Configuration of subinterfaces and main     interface
within the same bridge     group is not permitted
end
wr
Reply to this message by going to Home
Start a new discussion in Getting Started with Wireless at Home

Can any super nice helpful one tell me why i have DSL,but there is no dial tone in my house?

it has been 2 weeks , at begining, my phone and DSL all down and i was been told by verizon that it' s the problem of this 's garea. ...after 2 weeks, DSL is fixed up , but there is no dial tone for my home phone. i switched another telephone, cord, still no dial tone. ...and i used my cell phone to call my home phone, dial tone is busy....
...,,right now, what can i do? i called verizon, they will send me a technician and charge me $91 for first 30mins.........i am a poor man with little english ....what can i do? feel so helpless

They will only charge you if the problem is in your residence. If you had a wire maintenance plan there should be no cost. If your DSL is working your phone should be. I would say it is not a local problem in your residence, unless the phone jack where you are pluging your phone in is bad. Try unpluging your DSL modem and pluging your phone in at that location. If it works then you have a wiring problem, and will be charged for the repair trip.
To check if the problem is in your residence.
Open the customer side of the phone box on the outside and unplug the cable from the jack.
Plug your phone in at that location, and see if it works. If it does then the problem is a wiring issue in your residence.
If your equipment coming into the house is old, you may not be able to test it this way.
Message Edited by prisaz on 05-24-2009 10:15 AM

Need configuration help on producing dial tone

Similar Messages

Maybe you are looking for