Need current ethernet switch that supports Appletalk

I need the name(s) of currently manufactured ethernet switches (4 port or greater) that support Appletalk. Does anyone know if these are available? I use an Etherprint to connect from the ethernet to the HP printer.
emac G4, 1.25GHz Mac OS X (10.3.9) Airport base extreme base, HP 6MP printer

I agree with Kappy 100%.
But, I noticed you said you use a Farallon Etherprint adapter?
If yours is like mine, the etherprint has a special requirement. My etherprint isn't correctly detected by a 10/100 switch, and the switch tries to allow 100BaseT comm to go to the Etherprint. This locks up/locks out the Etherprint. The solution was posted on a Farallon web page (when they existed) 6-7 years ago. You must have a 10baseT hub between any 10/100 switch and the Etherprint - the hub is correctly sensed as 10baseT.
Like I said, I can't be sure if this applies to you - hope it helps.

Similar Messages

Cisco switches that support IPv6 L2 security

I'm looking for Cisco switches that support IPv6 layer 2 security. The following features are required:
MLDv2 snooping [RFC4541]
DHCPv6 snooping [RFC3315]
DHCPv6 messages must be blocked between subscribers and the network so that false DHCPv6 servers cannot distribute addresses.
Router Advertisement (RA) filtering [RFC4862, RFC5006]
RA filtering must be used in the network to block unauthorised RA messages.
Dynamic "IPv6 neighbour solicitation/advertisement" inspection [RFC4862]
There must be an IPv6 neighbour solicitation/advertisement inspection, as in IPv4 "Dynamic ARP Inspection". The table with MAC-address and link-local and other assigned IPv6-addresses must be dynamically created by SLAAC or DHCPv6 messages.
Neighbour Unreachability Detection [NUD, RFC4861] filtering
There must be a NUD filtering function to ensure that false NUD messages cannot be sent.
Duplicate Address Detection [DAD, RFC4429] snooping and filtering
Only authorised addresses may be allowed as source IPv6 addresses in DAD messages from each port.
Source: http://www.ripe.net/ripe/docs/ripe-501
I've looked around in some configuration guides for some Cisco access switches but I can't seem to find any switch supporting these functionalities.

See if this helps.
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
http://www.cisco.com/en/US/docs/ios/ipv6/configuration/guide/ip6-roadmap.html
You may also want to consult with your sales team.
What is the application?

Do I need to buy an ethernet switch that has a WAN port

I want to buy an Aiport Express to handle a WiFi only iPad and an old PPC iMac with 10.5.8 on it that has no WiFi card. The iMac gets on the internet from a cable plugged directly into its ethernet port (using DHCP). The cable comes off an antenna at the front of the cottage. A signal hits the antenna from a broadcasting tower about half a mile away.
I need to buy an ethernet switch for the Aiport Express to handle both the iPad wirelessly and the wired iMac. Does the switch have to have a WAN port or can I buy one with five LAN ports?
Message was edited by: Roy Vincent. Spelling error

So here's what I am planning to do. I get myself an ethernet switch. I plug my cable from my antenna into it. I run a cable from one of its five ports into my iMac. I run a cable from one of its other ports into my Airport Express. I configure the Airport Express in Bridge Mode. Now my wife can connect to the web wirelessly using the iPad and I can connect using the wired iMac --- and we can do so at the same time and indpendently of one another. No?
Sorry, but no.
You only have one IP address. With a switch feeding two devices, it will be a matter of chance as to which device gets the IP address.
The other device will not be able to connect to the Internet, since a switch cannot "split" the connection.
Instead, you need a simple wired router to "share" the public IP address that you receive. In turn, the router distributes "private" IP addresses to devices on your local network, so each device will be able to connect to the Internet.
As I mentioned, a switch cannot perform the functions of a router.

Do I need an ethernet switch or new router for IP camera setup with old Airport Express

Hello,
I am trying to setup a third party Foscam IP camera to my network so that I can ultimately use it as a baby monitor, and am having some difficulty. I currently still have an old Airport Express (with one ethernet port only). This is preventing me from setting up the initial camera because I don't have another ethernet port to plug it in to on the router. I am wondering if I can just buy an ethernet switch and have it "split" the ethernet from my modem to both the camera and the Airport (I do need to check with my ISP provider if they give me two separate IP address... but if they do, would this work?).
I am fairly sure however, that my ISP provider (comcast) only provides one IP for my account. Does this mean I would have to buy a new router altogether with more than one ethernet port on it or one with a WAN port? Would I, in this case, have to plug the modem into the WAN port on the router, and then the camera to one of the ethernet ports on the router?
I consider myself fairly tech savy, but when it comes to routers, IPs, LAN, WAN, etc. I get a bit lost. This has been creating quite a headache for me and any help would be appreciated! Thanks in advance!

I am wondering if I can just buy an ethernet switch and have it "split" the ethernet from my modem to both the camera and the Airport (I do need to check with my ISP provider if they give me two separate IP address... but if they do, would this work?).
Sorry, but this won't work as the modem expects only a single device ... either a computer or a router to be connected to it. Unless your modem is actually a combination modem & router or gateway device, then you would need a different router to solve your networking problem.

I need a display driver that supports win 8.1 for my hp mini

I RECENTLY UPGRADED MY HP MINI FROM WIN 7 TO WIN 8.1. SOME OF MY APPS WON'T DISPLAY OR OPEN AT ALL. I RECEIVE A MESSAGE OF.... MY RESOLUTION IS TOO LOW. WHEN I TRY TO CHANGE IT THERE ISNT A HIGHER OPTION AVAILABLE. WHAT CAN I DO?

Hi:
What is the full model number of your mini?
If you don't know, please see the info at the link below to find out.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00033108&lc=en&cc=us&dlc=en

Need CISCO switch which support 10 GBPS Traffice

Hi all,
In my data center currently I have 13 servers with Cisco Ethernet switch which supports 1 GBPS network that switch is up-linked with a sonicwall firewall.
We recently bought a new sonicwall firewall which has a two 10GE port.So I am looking now a cisco switch which has at least 16 10GE Fiber ports and one/two 1 GB Ethernet ports.That one 1 GB ports will connect to existing cisco switch and 16 GE FC ports will connect to firewall and as well as all server which I am planning to move one by one as we buy 10 GB supported SFC Network adapter cards for these servers.
Can you guys suggest me a Cisco Switch with 10 GE Fiber supported with 1/2 1 GBPS ethernet.Also if you can suggest me 10 GE Supported SFC adapters for Dell R 710,R720 and IBM x3550,M4 and IBMx3650 M4 servers.
Thank You

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
4500-X.

Can any one provide an web service technique that supports http post...?

hi,
i'm working with servlets. i need a webservice technique that supports http-post.
is it possible to work http-post using servlet & axis2 webservice....?

hi, if you are about to use axis2, consider trying JAXWS since its very fast to startup, it will then take care of everything what is beyond your business objects (so transforming in into XML etc) moreover, you're going to use web services, thus you ll be working with SOAP, which will wrap your business representation...
here a sample for a time -service. The Date object will automatically be trasinformed into appropriate xsd type by the axis2 engine
@WebService
public class Clock {
public Date getCurrentTime(){
return new Date();
}

Iscsi TOE... does it worthwhile to get network card that support it ?

Hi all,
I was wondering if purchasing an ethernet card that support iscsi & TOE will improve performance ?
Does the linux kernel for OVM 2.1.5 support ethernet cards with these features ?
If anyone is using successfuly iscsi ethernet cards with OVM, can you share your experience with us ?
Cheers,
Roye

At least three to five business days before you see a credit.

I need an ethernet cable connection to a non-wireless device that isn't near my current airport express. Can I buy an extra one to plug in near the non wireless device to receive the wireless data and put the signal out in ethernet form?

I need an ethernet cable connection to a non-wireless device that isn't near my current airport express. Can I buy an extra one to plug in near the non wireless device to receive the wireless data and put the signal out in ethernet form?

Yes, you can.
This is a special feature of the AirPort Express 802.11n. You will have to set it up "manually" to "enable Ethernet clients".
If your "main" AirPort Express is an 802.11n version, it is also possible to setup the second Express to "extend a wireless network" to provide additional wireless coverage in addtion to enabling the Ethernet port.
If you need the steps, post back to let us know what operating system you are using on the Mac or PC that will be used for the setup of the new AirPort Express.

I need a recommendation for SAN (Actually NAS) ethernet switches.

Hi, we have one Dell blade chassis with 8 servers ---- connected to stacked switches (3750) with EtherChannels ---- to NetApp (Controller 1 and 2 accordingly). Unfortunately, Dell blade servers only supports 1Gbps for port and NetApp also supports 1Gbps for each port (ports are all ethernet, not FC)
Questions
1) What kind of switch do you recommend? I know that it is not popular to use ethernet in SAN I just recognized that we have NAS, what do you recommend switches for NAS?
not SAN, so any MDS 9000 series don't work because it supports limited ethernet ports (many FC ports). I need many ethernet ports at least 48 ports from each switch. I know Nexus is one of candidates, but want to double check.
2) Most of vendors ask what kind of connection I have. I said usually just ethernet, not FC, not FCoE. Is it right? I believe that since I found NAS, it is "Ethernet"
3) The reason that I am looking for different switches is there are huge packet dropped (outbound) in switches (outgoing toward both dell servers and netapp; incoming is ok) We recently moved PtoV so, it is possible that traffic volume was increased. But output doesn't give me lot of information like below. Do you have any recommendation for further t-shoot?
(connected interface to Dell)
GigabitEthernet2/0/34 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 580a.20f1.db22 (bia 580a.20f1.db22)
Description: Chassis8
MTU 9000 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is 10/100/1000BaseTX
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:00:57, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 32453861
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 3853000 bits/sec, 364 packets/sec
5 minute output rate 2275000 bits/sec, 368 packets/sec
15864561667 packets input, 16858567695886 bytes, 0 no buffer
Received 4347 broadcasts (6 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 6 multicast, 0 pause input
0 input packets with dribble condition detected
47326292220 packets output, 62942914503089 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures
(connected to NetApp)
Port-channel2 is up, line protocol is up (connected)
Hardware is EtherChannel, address is 2c3e.cfaa.af03 (bia 2c3e.cfaa.af03)
MTU 9000 bytes, BW 3000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 2/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, link type is auto, media type is unknown
input flow-control is off, output flow-control is unsupported
Members in this channel: Gi1/0/3 Gi2/0/1 Gi2/0/2
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:00:01, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 3316452
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 6693000 bits/sec, 2048 packets/sec
5 minute output rate 30028000 bits/sec, 2773 packets/sec
107334585357 packets input, 140120529103340 bytes, 0 no buffer
Received 5609191 broadcasts (407218 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 407218 multicast, 0 pause input
0 input packets with dribble condition detected
38961062194 packets output, 40437523739199 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
Thanks.

Hi, we have one Dell blade chassis with 8 servers ---- connected to stacked switches (3750) with EtherChannels ---- to NetApp (Controller 1 and 2 accordingly). Unfortunately, Dell blade servers only supports 1Gbps for port and NetApp also supports 1Gbps for each port (ports are all ethernet, not FC)
Questions
1) What kind of switch do you recommend? I know that it is not popular to use ethernet in SAN I just recognized that we have NAS, what do you recommend switches for NAS?
not SAN, so any MDS 9000 series don't work because it supports limited ethernet ports (many FC ports). I need many ethernet ports at least 48 ports from each switch. I know Nexus is one of candidates, but want to double check.
2) Most of vendors ask what kind of connection I have. I said usually just ethernet, not FC, not FCoE. Is it right? I believe that since I found NAS, it is "Ethernet"
3) The reason that I am looking for different switches is there are huge packet dropped (outbound) in switches (outgoing toward both dell servers and netapp; incoming is ok) We recently moved PtoV so, it is possible that traffic volume was increased. But output doesn't give me lot of information like below. Do you have any recommendation for further t-shoot?
(connected interface to Dell)
GigabitEthernet2/0/34 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 580a.20f1.db22 (bia 580a.20f1.db22)
Description: Chassis8
MTU 9000 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is 10/100/1000BaseTX
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:00:57, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 32453861
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 3853000 bits/sec, 364 packets/sec
5 minute output rate 2275000 bits/sec, 368 packets/sec
15864561667 packets input, 16858567695886 bytes, 0 no buffer
Received 4347 broadcasts (6 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 6 multicast, 0 pause input
0 input packets with dribble condition detected
47326292220 packets output, 62942914503089 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures
(connected to NetApp)
Port-channel2 is up, line protocol is up (connected)
Hardware is EtherChannel, address is 2c3e.cfaa.af03 (bia 2c3e.cfaa.af03)
MTU 9000 bytes, BW 3000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 2/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, link type is auto, media type is unknown
input flow-control is off, output flow-control is unsupported
Members in this channel: Gi1/0/3 Gi2/0/1 Gi2/0/2
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:00:01, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 3316452
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 6693000 bits/sec, 2048 packets/sec
5 minute output rate 30028000 bits/sec, 2773 packets/sec
107334585357 packets input, 140120529103340 bytes, 0 no buffer
Received 5609191 broadcasts (407218 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 407218 multicast, 0 pause input
0 input packets with dribble condition detected
38961062194 packets output, 40437523739199 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
Thanks.

Best current IOS that supports Netflow in a 6509?

Hello,
We are trying to enable Netflow in our core switches (6509E). The problem that we have is that once we enable it the CPU usage is noticeable higher and I've been thinking it could be IOS related. Does anyone have a recommendation of an IOS that provides good performance when Netflow is enabled?
Thank you,
Francisco.

We have:
(s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(33)SXJ
Netflow is disabled and we do not want to enable it since we saw some performance issues and we were told not to enable it again. At some point we will need to enable it, that is why i am thinking there might be a better supportive IOS version for Netflow.
We have a WS-C6509-E (R7000) processor (revision 1.2) with 983008K/65536K bytes of memory

After I download Itunes, when trying to sync Ipod, message says "needs newer version of mobile support, uninstall Itunes, and reinstall Itunes, and the same process starts all over again. why is that?

after I download Itunes, when trying to sync Ipod, message says "needs newer version of mobile support, uninstall Itunes, and reinstall Itunes, and the same process starts all over again. why is that?

Try removing and then reinstalling the Apple software using these instructions.
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7
The above containes a link for XP. Also. make sure you install the correct Apple software, It comes in 32 and 64 bit and you need the one that is the same as the computer OS

I am unable to connect to the internet, there is a pop-up that says "We're sorry, but the Safari browse version you are currently using dos no support the community toolbar". My computer does say that it is connected to the internet until I open Safari.

I am unable to connect to the interent. At the top of the screen my computer says that I am connected. When I open up Safari there is a pop up that say "Community Toolbar We're sorry, but the Safari browser version you are currently using does not support the community toolbar" and when the Safari page opens up it says "You are not connected to the Internet. Safari can't open the page .... because your computer isn't connected to the Internet." I have tried Network Diagnostics and tried to reset Sfari, empty Cache as well as deleted all of my interent history. I am unable to use Time Machine because I never set it up. If someone knows how to help I would very much appreciate it!!

Some instructions for removing Community Toolbar are available in this thread: https://discussions.apple.com/message/15868085#15868085

Can I use an ethernet switch to add a "pogoplug" device to my Airport express router? Or do I need a different router?

I have an airport express router and decided to get a "pogoplug device" (cloud service to store files etc.). It requires to be connected to router per ethernet but I realized too late there is only one ethernet connection in the router. A friend suggested I get an ethernet switch but it still doesn't work...Do I need a new router?

Then, unfortunately, no as the single Ethernet port of the AX needs to be connected to the Ethernet port of your Broadband modem.
One option is to get another AX, and then, configure it as a wireless Ethernet bridge. It would connect to the first AX by wireless, and then, you can connect the PogoPlug to it.

How do I switch to 'fly by' view in iOS 6 Maps in cities that support it?

Curious how to switch to this fly by mode in cities that support it in the new Maps app.
Thanks
Harry

Add your own review to those already there complaining about this:
https://itunes.apple.com/us/book/big-nate-makes-a-splash/id651440000?mt=11
You could also try asking for a refund via the "report a problem" link on your receipt.

Need current ethernet switch that supports Appletalk

Similar Messages

Maybe you are looking for