Need definitive solution Suite 6.83.14.1 not worki...

I see a lot of comments of frustration. but no one solution.
I just received my CA-42 cable with software.
I have Windows XP with Service Pack 2
2118 nokia phone
6.83.9.0 Nokia Connectivity Cable Driver
6.83.14.1 Suite
I got a disk with the cable... I couldn't get the driver to work with what ever version it came with and so decided to get the latest software.
What I've read is that the installation should take care of installing the driver.
I get to a point in the Nokia suite "Get Connected" and it appears that it can not find the cable or cable with phone
I the XP wizard keep responding "new hardware found" but it can not resolve the connection. I'm not sure if Nokia suite is suppose to do this without the xp wizard or not.
Can this be made to work or not?
I've never tried this setup out before on any phone.. I'm new to this. I just wanted to be able to back up the data on the phone.
What is the solution please

Removing the cable driver did not work.. Your suggestion was not quite as specific as I was hoping for
I left the 6.83.14.1 Suite installed.
Is the xp wizard for installing drivers part of the process?
I have yellow ? marks in the system hardware listing with these cable drivers
I've found two other cable drivers... This term cable drives why don't the just say USB driver?
The Cable Drivers/USB I found are came from http://www.nokia.com.au/nokia/0,,81050,00.html
Will they work with any Suite or do I have to find a particular suite to match them up with?
I've tried them both. Nokia_Conn_Cable_Driver_150_2_eng.exe and Nokia_Conn_Cable_Driver_145_5_eng.exe.
with one of them I did get something to flash on my phone at one point... It came and went and now I'm not even sure which one of the drivers it was. Xp is a pain in the butt forcing one to have to reboot after an installation.
This being the case I'm going to go through the process of installing these two cable drivers once again to see if I can get a handle on where and when I get something.
Still I'm looking for that definitive step one step two etc etc. using which driver which suite downloaded from where etc etc. on how to get it all working..
Is this available?

Similar Messages

I need a reliable office suite. Open Office is not working well for me. Any suggestions?

I need a good reliable office suite. Open Office is not working well for me. Any suggestions?

If you mean Open Office is not always able to correctly open documents received from clients created with MS Office, then the only real solution is to purchase Office 2011 for Mac. As good as some of the free alternatives are, they can't duplicate every feature of MS Office.

Hi I need ur help actually my iPhone 5 is not working properly I been to apple store they said u have to booked online for repair but I couldn't find where to register plz help out thx ali

Hi I need ur help actually my iPhone 5 is not working properly I been to apple store they said u have to booked online for repair but I couldn't find where to register plz help out thx ali

Dollersheikh wrote:
... I been to apple store ...
Go to that Apple Retail Stores website and click on Make a Reservation...
Here's an example...
http://www.apple.com/retail/crossgates/
Store List here > http://www.apple.com/retail/storelist/

[solved] Need DEFINITE solution to 'no more qt-config' problem

The qt-config utility (the one with which you could "switch" between qt3 and qt4) recently vanished. Is there a known definite solution to this problem, i.e. a way to set EXACTLY the same states/variables/symlinks/whatever that were set with "qt-config qt" and "qt-config qt4"?
And by the way, why was qt-config removed?
Last edited by Rulatir (2009-01-11 11:14:19)

Because KDE 4.0 is just around the corner, qt4 from [community] will be moved to [extra] as qt. qt (3.3.8) will then be renamed to qt3 (still in [extra]).
http://archlinux.org/pipermail/arch-dev … 02910.html
As for the QT4 compilation, you won't need the qt-config anymore because qt4 is the "default" qt.
$ which qmake
/usr/bin/qmake
$ qmake -v
QMake version 2.01a
Using Qt version 4.3.2 in /usr/lib
For Qt4 compilation:
source /etc/profile.d/qt4.sh
qmake (I explicitly use the /usr/bin prefix though)
make
For Qt3:
source /etc/profile.d/qt.sh
${QTDIR}/bin/qmake
make

Should I return my new MacBook Pro? Creative Suite CS and CS2 do not work?

I am soooooooooooooooo ******!!!!!!!!
I just purched the top of the line MacBook Pro and learned that the Adobe Creative Suite products do not work on this machine. I contacted Adobe and they said they will not have an update until they release the next version, which won't release until (at the earlies) the end of this year. While Photoshop, Illustrator, InDesign are not crucial aps for me, I do use them for business regularly.
With this being the case, I ask the mac community using these machines, should I return the computer, buy a g4pb (my TI just literally fell apart) ? Reading the board hear and various news articles, there seems to be a few issues (whine - apps - etc).
I guess I should have looked into this more before purchasing, but I trusted Apple to release products that are ready for users.
This is the most expensive computer I have ever puchased and I need it to do everything my TI PB did.
Is the MacBook Pro worth the early adopter hastle?
(thank god I haven't opened the box yet!)
MacBook Pro Mac OS X (10.4.5)

According to Adobe:
Creative Suite 2 will work on Rosetta with the exception of one componet. Version Cue Workspace (Server) does not work under Rosetta. As of Jan 31 2006 this was the only known issue with using the suite on Intel Mac's.
Adobe Systems
Creative Suite: Yes (with performance losses)
Photoshop Elements: Yes
(Adobe has posted "FAQ: Adobe Support for Intel-based Mac Computers" [intelmacsupport.pdf]
http://www.adobe.com/products/pdfs/intelmacsupport.pdf , which discusses Intel support, development, Rosetta compatibility, rough schedules, and more for Mac applications from Adobe and Macromedia.)
I would recommend that if you are going to use this program that you have 2 GB's of RAM seeing as I hear that Rosetta can be a RAM hog. Hope this helps you out.
I am soooooooooooooooo ******!!!!!!!!
I just purched the top of the line MacBook Pro and
learned that the Adobe Creative Suite products do
not work on this machine. I contacted Adobe and
they said they will not have an update until they
release the next version, which won't release until
(at the earlies) the end of this year. While
Photoshop, Illustrator, InDesign are not crucial aps
for me, I do use them for business regularly.
With this being the case, I ask the mac community
using these machines, should I return the computer,
buy a g4pb (my TI just literally fell apart) ?
Reading the board hear and various news articles,
there seems to be a few issues (whine - apps - etc).
I guess I should have looked into this more before
purchasing, but I trusted Apple to release products
that are ready for users.
This is the most expensive computer I have ever
puchased and I need it to do everything my TI PB
did.
Is the MacBook Pro worth the early adopter
hastle?
(thank god I haven't opened the box
yet!)
MacBook Pro
Mac OS X (10.4.5)

K430/K450: here`s the SOLUTION to Lenovo Power control switch not working anymore.

If your power control switch isn`t working anymore BUT you didn`t unistall it or erase some of his files, chances are that over time some software/update took control of some setting used by the Lenovo switch.
If this is the case, before reinstalling the software, try the following:
1 - Check your power plan option, if is on something else than Lenovo change your power plan option (scheme) to Lenovo Power Scheme.
2 - Access your pc advanced startup setting (win+x) check for the services LitModeCtrl and LenovoComService and set the two services to automatically start when the computer startsup. If it`s not working 99% is because some software (the most common is Samsung SSD Magician) has set the two to "Manual". Change to "Auto".
3 - Reboot and the Power control switch software will be working again.
I wonder why no one from Lenovo advice this, but i`ve had to find a solution myself after countless hit & miss attempts.

hi FlashOfLight,
Welcome to the Forums.
Have you tried performing a system restore to undo the changes? (by default, this feature is set to enabled)
regards,
neokenchi
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Unknown Audio Driver Needed for HP Pavillion DV6910us because sound is not working

1.HP Pavilion DV6910us
2. Came with Windows Vista but computer was re-imaged and now has Windows 7
Sound is not working and the error says No Audio Output Device is installed

Would like to know the product number of the notebook as it i essential for us to look for the drivers and solutions. Below link helps you find the product and the serial number oif the notebook.
http://h10025.www1.hp.com/ewfrf/wc/document?tmp_renderType=findModel&cc=us&dlc=en&docname=c00033108&...
Let us know for more!
"I work for HP."
Click the Kudos star to say thanks
Please mark Accept As Solution if it solves your problem
Regards
Sreenag

Need help with sound on media and itunes. not working

The media player and itunes sound does not work. need help

You either need to kill all sounds when they click the
Next/Back buttons OR you could disable the buttons until the sound
completes.
Hope that helps!

My iPad would not complete the back up to iCloud. The solution re: resetting my iPad did not work. Are there any other ideas?

My iPad would not complete the back up to iCloud. The suggestion re: resetting the iPad did not work. Are there any other ideas?

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

HT1933 I need a refund for an apps wich does not work

I need an immediate refund for an apps call SLOVAK TV it does not work!!!

Step 1: Contact the Developer.
Step 2: Contact iTunes Customer Service and request assistance
Use this Link > Apple Support iTunes Store Contact
Note: All sales are final.

Traditional Solution To "White Screen of Death" Not Working

My 2G 32GB iPod Touch was working fine, and an hour later, I got the "white screen of death." I tried the hard reboot, holding down the home/sleep button for 10 seconds. After that failed, I tried 15, 20, 25, etc. I tried upgrading to 4.0.2. Nothing. Restoring to factory settings. Nothing. Restoring factory settings AGAIN. Still just a white screen.
A couple days later, I was seeing if it was just a screen error. Turns out, whenever I slide where the slider would have been on the screen, it made the unlock sound. When I had unlocked it, I poked around until I got into something with a keyboard, and all of the letters had the "click" sound whenever they were touched.
My opinion is that the problem is a loose wire that connects to the LCD screen, just randomly getting unloose. However, I want a second opinion, and a potential solution.
AND DO NOT TELL ME TO HOLD DOWN THE HOME AND SLEEP BUTTON FOR 10 SECONDS. IT DOES NOT WORK FOR THIS CASE. LET ME REPEAT. THAT SOLUTION. WILL NEVER WORK. FOR THIS SITUATION.

Yeah. I've done that about a thousand times. Perhaps you didn't read what I wrote in all caps. Or perhaps you misread the title.
http://www.youtube.com/watch?v=okvp29UhHCM&feature=related
Imagine that what's happening in this video is on an iPod, and isn't an app. And there's no display of time or WiFi signal.

Solution For Microphone - Low Volume or Not Working

I just read pages of forum discussions trying to fix extremely poor microphone volume on my Macbook Air. I tried to change all kinds of microphone settings, doing hardware resets, and uninstalling software. I even made an appointment to the Genius Bar because some people posted that they had to replace their microphones.
However, I finally found a simple solution. It turns out that after some time, dust gets inside of your microphone and blocks the holes through which it captures the sound. You need to take a tiny needle or a wire and poke each tiny hole of the microphone located on the left side of the macbook. After taking out some dust, my microphone began working as new.
Hope this helps to someone in the future.

Thanks a million! PlotinusVeritas!
A needle was to big as the holes are so tiny.
I took an old toothbrush and used one of its hair. They're made to be thin and quite tough.
This made the trick and my Macbook Air's microphone works like charm now

Need help with XiFi Platinum... Not worki

Hello everyone, I'm having (some?) trouble with my XiFi Platinum. I've had it for a little over a year now, and I personally think it's broken but I just want to be sure before I go out and buy something to replace it...
So yesterday it worked fine justl like new. Then I installed a new 8800GT (From 2 7900GT's being removed) and connected that. I had to rewire some things, move a harddri've around to make it fit, etc, but i didnt really mess with the soundcard, there was no need to. But when I turned the computer on after installing I find that there is no sound at all. Windows didint even detect the card anymore and simply said ''no audio device'' in the sound properties.
I then proceeded to re adjust the card in the same PCI slot and after reboot windows did recognize the card properly. I continued to test if it worked, because all the software settings said it should be working. I turned on my speakers and without even having any audio files running i had this high pitched ringing noise that never went away (until i turned off the speakers).
OK so I thought it might have been the PCI slot, so I doubtfully tried another slot. The card isn't recognized at all in the second slot, and I go back where I started to ''no audio device detected." I deleted the Creative drivers and downloaded the most recent XP32 ones that I'd need (SBXF_PCDRV_LB_2_5_0006.exe), but at the start of the installation it simply said something like ''there is no supported device detected, installation will now close.'' So at this point I'm not sure what I need to do because I think it's broken...
System Specs:
Motherboard: MSI P6N SLI Platinum? LGA 775
Processor: Intel Core 2 Duo E6550 @ 2.4GHz
RAM: (2xGB) Patriot signature DDR2 800
Hard Dri'ves: (2x) Western Digial Caviar 200GB (=400GB)
Graphics Card: eVGA Geforce 8800GT 52MB
Sound Card: CL SB Xi-Fi Platinum (http://us.creative.com/products/product.asp?category=&subcategory=208&product=4065 )
OS: Windows XP Home 32bit
Also, this is a ''relati'vely'' fresh install of win XP that I did about 2-3 weeks ago. Reinstalled nVida drivers last night after installing the 8800GT. At this point I'm thinking that i might have burnt out the card at some point while working with the computer, and I can't see otherwise, but I dont know..
Any help is appreciated.:manvery-happy:
**EDIT** I forgot to mention that after I switched the card to a new PCI slot it was detected by Windows as a new PCI device, but it didnt work and I couldnt install drivers. Strangely I think the bios got reset or something because after I moved the card the MSI logo was displayed as opposed to the boot information, which I had it set on. The clock also got reset.. I'll have to look more closely at the bios to see if anything else got changed too.
Message Edited by sniper23 on 07-22-2008 02:06 PM

Quote from: Svet on 13-October-09, 20:13:27
Try with better PSU, single rail with at least 40A at +12V
Any recommendations for a better PSU, I've also been looking at the stats for my current psu
quote some specs on it..
"Triple 12V Rails provide independent reliable power to the CPU, video card and other components with a combined rating of 50A (40A on 520W) maximum! Advanced circuitry design that automatically enables power sharing between the triple +12V rails in an event of overload on any single +12V rail."
Really thought this PSU would handle it.

What is the best solution to monitor Exchange server was not work normally

Hi everyone ,
I have a problem about how to monitor (or detect) the status of Exchange server , so that I
can inform our users to change the mail server destination they will connect.
Can I just test the connection status of SMTP, POP3 , IMAP3 ? and How ??
Anyone can give me a solution ?
Thanks everyone !
Tinker Chiou

Hi,
Have you found the solution?
I am also facing the same problem. When My proxy server failed in my network, The MS Exchange Server also didn't work. At this point when the servlet try to send the mail to the customer, it is geting hanged, no responce from the servlet.
Please advise me how to check the status of the MS Exchange Server.
Thanks in Advance,
Ramaswamy

Sun Java Communication Suite 5 using example deployment not working

I download the sun java communication suite 5 for solaris sparc.
I have a sunfire 280r server with Solaris 9 9/05 HW s9s_u9wos_06b SPARC installed.
I follow the document 820-0086.pdf to try the product (deployment example), i succesfully installed the product using acasalud.com.ar as the domain.
The problem arises when i begin to verify the installation(page 16), i sucessfully start the web services but when i put:
http://fully-qualified-hostname:web-server-port/amconsole
Nothing happens, the amconsole url doesn't exists.
Somebody knows how to solve this?

I found this in the logs:
Web Server Admin command (/SUNWwbsvr7/bin/wadm) not found!|#]
[#|2007-12-13T17:53:02-03:00|WARNING|CommsSuite|JavaESInstall|_versionID=1.0;_th
readID=11;_SourceJavaFile=EntsysConfigurator;_SourceMethodName=executeCmd(cmd,en
vp,dir);_CommsSuiteMessageID=;_CommsSuiteResourceBundle=|
ldap_add: Already exists
ldap_add: Already exists
ldap_modify: Type or value exists
ldap_modify: No such attribute
ldap_modify: No such attribute
ldap_modify: No such attribute
ldap_modify: No such attribute
ldap_modify: Type or value exists
ldap_modify: Type or value exists|#]
[#|2007-12-13T17:53:02-03:00|SEVERE|JavaES|JavaESConfig|_versionID=1.0;_threadID
=11;_SourceJavaFile=IdentityServConfigurator;_SourceMethodName=configure();_Comm
sSuiteMessageID=JavaES_ConfigIS24;_CommsSuiteResourceBundle=EntSysLoggingResourc
es;_CommsSuiteArg1=1|Access Manager Configuration Failed ...1|#]

Need definitive solution Suite 6.83.14.1 not worki...

Similar Messages

Maybe you are looking for