Need driver for combo drive px1055e-1nst

hi, i need a the drivers fore my combo slimline dvd/rw px1055e-1nst
where can i download it from ?

Hi
Usually you dont need any drivers for the drive.
Microsoft Windows OS uses the own drivers which are included in the OS.
But you can try to check this site:
http://www.cdrom-drivers.com/
Maybe there you have more luck.

Similar Messages

Need to replace combo drive without electrocuting myself

I want to replace my combo drive. I've purchased the proper replacement super drive, but guys at the Apple store warned me about the danger of electrocuting myself or frying my eMac because of the stored up power in the computer. Is this a real concern?
Can anyone help me with what to do so I don't fry myself or the computer.
Thanks,
BennySez

Michael Lafferty wrote:
This discharge procedure has not been required for years, and has never been for eMacs.
I beg to differ. This is from page 13 of the *eMac Service Source Repair Manual*, published by Apple in 2002:
"Warning: This product contains high voltage and a high-vacuum picture tube. To prevent
injury, always review the Service Foundations: CRT Displays course for safety information.
Whenever the rear housing of the computer is removed and before replacing a module,
you must
1. Discharge the CRT (shown below) and remove the anode cap.
2. Establish an ongoing ground by using a cable with alligator clips at both ends. Connect one end to the anode aperture, and connect the other end to the metal CRT frame (as shown below).
3. With the CRT discharged and the ongoing ground in place wear a grounding wriststrap to prevent equipment damage from static electricity
Page 77 covers replacement of the optical drive; these preliminary steps are listed:
Preliminary Steps
Before you begin, do the following:
• Place the computer face down on an ESD mat.
• Remove the user access door.
• Remove the feet.
• Remove the rear housing.
• Discharge the CRT.
• Remove the fan.
• Remove the Faraday cage.
• Remove the digital module assembly.
• Remove the hard drive.
• Remove the heatsink.
• Remove the logic board.
Now, this manual covers the original eMac model. Perhaps later models of eMac do not have the same requirements. But until such documentation from Apple can be found, I think it foolish to not follow the guidelines set out in this manual, for all eMac models.
<Edited by Moderator>

Looking for combo drive part numbers

I recently saved an iBook from the dumpster and want to update the cd rom with a combo drive. After looking online and on eBay, I see LOTS of drives. However, i don't know the exact part number(s) that will work with mine. Help anyone.
Thanks

Thanks for the information. I have looked at the instructions online for replacing the drive and am not 100% sure I am up to the task. On the other hand, I would really like to replace the cd drive and put in a larger hard drive so I guess it would be best to do it all at once while I have it apart.

Pls i need help for audio driver for lenovo 3000 j series

hello, can sombody help me to find driver for lenovo 3000 j series audio driver.
i did format to my computer and reinstall windows XP and now i don't have audio, i already downloaded all drivers from lenovo website and nothing is working. pls pls help. thank's.

If you are using Windows Vista go to All Programs/Palm and click on the folder and select Hot Sync Manager and then try to sync with the USB cable. If you are using the Windows XP go to Start/Programs/Palm/Hot Sync Manager and then try to sync. If you don’t have the palm folder at all on your PC you have to install it. Here is the link http://kb.palm.com/wps/portal/kb/common/article/33219_en.html that version 4.2.1 will be working for your device Zire 72.

Format external hard drive for backup drive for Mac Pro

How do you format an external portable hard drive to work as a backup drive for the Mac Pro?

If you plan to use Time Machine then Time Machine will take care of that for you once you choose the drive as your backup destination. If you want to do it yourself then you need to attach the drive; once it is mounted, open Disk Utility and select your drive from the left hand side bar. Once highlighted go to the main window and click on the subheading "Erase". The format needs to be "Mac OS Extended (Journaled)". Click Erase and wait for the operation to complete. Now that you have a freshly prepared volume it can be used for Time Machine back up. Time Machine will recognize the disk and ask you if you would like to use this volume at which point you should follow the prompts to begin your back up.

Upgraded Hard Drive, now Combo drive wont recognize. HELP!!!!

I upgraded my hard drive, installed the os-X (10.3.9 i think) and the cd combo worked fine, removed the combo to do somthing for the laptop (installed it in the iBook), and now when I put another combo drive (same model different drive) into the mini, the mini doesn't even recognize that there is a drive at all,
it will take a disk, but wont eject or mount.
what should I do?
should I put the original drive into the mini?
Also, i cant re-install OS-x because the optical drive wont mount in the mini, and the ibook says that It cannont use the software with the version that is installed on it (10.4.somthing)

There isn't a BIOS in G4 Mac systems - in essence, rather than having a pre-determined configuration, the system checks for existent components at startup such that if the drive in the system was recognised and had a viable driver, it would be functional.
First thing to do is check whether the system sees the drive at all. Go to the Apple menu and select 'About this Mac'. Then click the 'More info' button when the dialog box gives the MacOS version, processor and memory.
The click the 'ATA' tab on the left. You should see two entries - the first being the internal hard drive which will be shown in the lower portion of the right-hand pane by model and capacity. If the combo drive is not showing there with any entry (ie, there is only one ATA device, the internal HD) then more than likely the drive is not connected correctly as Boece has suggested. If it IS listed there and correct by model number, then it may be that the drive itself is faulty or the system's power management unit isn't controlling it correctly.
If the later is the case, a PMU reset may help. Try the following:
- Unplug all cables from the computer, including the power cord.
- Wait 10 seconds.
- Plug in the power cord while simultaneously pressing and holding the power button on the back of the computer.
- Let go of the power button.
- Press the power button once more to start up your Mac mini.

Basic CD-ROM drive to combo drive/wireless internet

I have a 12-inch iBook G4 with a basic CD-ROM drive - but I want a combo drive so that I can play DVDs on my computer. Does anyone know how I can get this done and about how much it costs??
I'm also looking to find a wireless internet card for the same computer - any suggestions??

You may want to look here for drive upgrade options:
http://store.fastmac.com/advancedsearchresult.php?keywords=SuperDrive+8x
That was only a superdrive. If you are looking for an internal combo only you may want to look at otherworld computing:
http://eshop.macsales.com/shop/optical-drives/superdrives/
Another option is an external. This works for me for playback w/ the Apple player. If you find a cheap one and have issues look to vlc. Bus power is a major plus here.
If I were you I would consider looking into an external bus powered burner, as this will be portable to any other machines or future ones.
ex: any of the products here: http://www.lacie.com/products/range.htm?id=10037
There are successful wireless options from third parties. This link should give you a rundown of options:
http://www.macosxhints.com/search.php?query=usb+wireless&type=stories&mode=searc h&keyType=all
Unfortunately, many of these products are specific down to the last tiny letter on the outside of the box. Some are mystery products where the actual device inside the box may or may not work. As far as I know, none of these are directly supported by Apple and that, to me, is a serious drawback.
Good Luck
-j
(is your mac an education one?)

Need help for this driver instalation

I need help!
for hp 2000-2110TU ,
i installed the memory card reader driver but the message is displayed like install your memory card driver, what have to do now..?

Is that a USB memory card reader that you have connected.
**Click the KUDOS star on left to say Thanks**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.
Thank You,
AntonyG1
Although I am an HP employee, I am speaking for myself and not for HP

Satellite Pro L300 -software-service says I need update for graphics driver

I downloaded the DesignByMe software from http://designbyme.lego.com/en-us/default.aspx
The installation run without problems, but when I want to start the program it restarts over and over again. The picture doesnt load fully, instead there are black spots. I cant click on anything nor close to programm .I thought maybe the installing process didnot finish properly so I downloaded the software again but the problem is still the same. Im using a new Satellite Pro L300 28w with Windows 7 and Mozilla Firefox 3.6
I contacted the lego support and they answered: "You most likely need to update your graphics driver. Please contact your computer manufacturers customer service or website for a free upgrade"
Is this likely and if so which upgrad edo I need?

Hi
I dont know if updating your display driver can solve this problem but if the manufacture of the software says that its worth a try!!! ;)
The update is pretty easy: Firstly download the latest version here:
http://eu.computers.toshiba-europe.com => Support & Downloads => Download Drivers
If you have downloaded the latest version, remove the old one firstly. Check the software list in control panel and follow the screen instructions. I assume you have to make one restart and after this you can install the downloaded version.
Good luck! :)

Need figure for Hard Drive Space saved with FCS and LS installed

Hello (this is my first post!)
Have a quick question... I am planning a purchase of a 17" MBP in the very near future, and am trying to get a total GB required for my HD with the software I will be using. Basically, if the total is low enough, I can get an SSD!
So here is my quandary. If I were to install Final Cut Studio and Logic Studio on a MBP, there is overlap in Compressor and Soundtrack Pro, and in all (?) of the audio content. If I understand the tech spec breakdown correctly, that means at least 22 GB (from the audio content breakout) of the installation is duplicate. Does anyone know the total GB (for the programs and content) that would be duplicate? I am looking for how much HD space that would be saved in this scenario. This will help me out tremendously in planning my purchase.
Thanks!
Dave
PS - BTW, I am aware some folks install all of the content on a separate external disk. While I have read up on the Pros/Cons, I figure that if I were to have an SSD large enough, it would be excellent to not have to plug in an external HD since the internal speed should suffice...

If you can, aim for a 256GB SSD, which will hold your core programs and have overhead for content (should you choose to store it there) and future expansion/growth.
If it's a 2011 machine, then start eyeballing external drives sporting the ThunderBolt interface, which is RIDICULOUSLY fast. A bunch of products are likely to be announced at this week's National Association of Broadcasters show, and will begin shipping in the days/weeks to come. The external drive should have no problem offering you capacity and performance that you'd need for your work. I have to admit, I'm a little envious - the new 'sandy bridge' MacBook Pro with that ATI chip and the new interface look really fantastic, it's an incredible amount of power to have on the go.
Good luck!

Converting to SSD Drive for Boot Drive on m7 with Win8

I just bought a new m7-j020dx (product code E4S19UA#ABA) with Windows 8 from Best Buy. Unfortunately, it came with a standard hard disk drive (HDD) and I would like to install a Solid State Drive (SSD). I have an Intel 320 and 530 series drive. But I have not been able to get a bootable drive from this.
The first thing I tried was cloning the factory drive to a new 530 series drive using AOMEI Backupper. I got a write error on the third partition. I thought perhaps the drive was bad so I tried it again with an Intel 320 series SSD drive. Same error.
The next attempt was to clone the drive to another 1 TB drive (connected via USB), shrink the main partition with MiniTool and clone to the 320 series SSD. The cloning went fine. However, with the new SSD installed, the computer will not boot and I get "Error0x0000225", something about a file not found. Turning off "secure boot" in the BIOS setup did not help (I did this after the clone).
So I thought I would make a clean install of Win 8. I generated a recovery disk on a 32GB SanDisk USB drive using Win8's recovery disk generator (as instructed on the HP site). I then ran the recovery program off the USB drive and after a couple of hours of installing driver software and several reboots, I get an HP message stating the installation was not complete. Repeating the install did not help.
I am not sure what the problem is.
Is the USB recovery disk a made from the original HDD bad (one only gets one shot at it)? Do I need to order media from HP on disks? Are there issues with using SSD drives on these computers? Do I not have a BIOS settig correctly (UEFI)? Is there some Intel storage drivers getting in the way?
I think my next step will be to create a disk Image and then put it back to the SSD drive. But I doubt this fixes the issue with booting to it.
Another option might be to do a fresh build using Win8 media and then download and install each driver from the HP website.
Any ideas out there in the land of experts?
This question was solved.
View Solution.

Vachsen
Please install the HDD Back
Update your BIOS
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-128144-1&cc=us&dlc=en&lc=en...
Install the new Intel Rapid Start Technology Driver
https://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=23496&ProdId=2101&lang=eng&OSVersion...
Reboot
Attach the SSD over USB Cable
Update the SSD Firmware
https://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=18363
Reboot
Use the Intel tool for drive Copy
https://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=19324
Say thanks by clicking the "Kudos! Star" which is on the left.
Make it easier for other people to find solutions, by marking my answer with "Accept as Solution" if it solves your issue.

Where can I download Hp DVDRAM GU70N driver for DVD drive?

I need the following driver but cannot seem to find it. The HP Assistant does not seem to let one search for drivers just updates. Please need help.

CherylG wrote:
Drivers for CD/DVD drives are normally provided by the OS. Software adds extra functions. What problems are you trying to solve?
When I load a CD or DVD into the drive teh laptop does not see the DVD or CD so I cannot download data or see a movie. When I run the diagnostic ot tells me that the HP DVDRAM GU70N SATA CDROM Driver is bad. It tries to use the data on the recovery disk of the OS but this does not fix the problem. Hence I think I need a new driver installation file.
Any sugggestions

7200 or 5400 portable hard drive for scratch drive?

I am trying to decide whether to buy a f7200rpm or 5400rpm portable hard drive to store some of my video footage on but seem to have conflicting answers on the topic. Basically, I need to offload some of my unedited footage from my MBP as it is taking up lots of room but I need also to have this with me when travelling so that I can continue working on it, therefore the need for a small portable hard drive. I have pretty much decided to get one of the G-tech mini drives, but should I get a faster 7200rpm for video, or will this make no difference, in which case a 5400rpm will have more capacity for the same price. I emailed G-Tech and their reply was a bit vague, basically saying that with firewire 800 there "might be a slight increase in performance", but I am still not sure what this means in real terms when working with video.
I thought the best place to ask was here, so if anyone can advise I would be grateful, thanks.

I have a single G-Tech mini fw400 case with a 5400 rpm drive that is perfectly useful for capturing and editing simple DV. But, I purchased it for simply capturing video while I was out of the studio. I would not use it for serious multi layer editing. If pressed, I would guess the limits have more to do with it being fw400 than the rotational speed.
What a faster rotational speed often does is give you faster seek times.
Still, if I were in the market today, I'd go with something like a two drive miniRAID system (eg Caldigit VRmini) that can connect via FW400, 800 or eSATA.
x

Dv6812nr - Vista 32bit driver for DVD drive issue!

So new drive shows up as H - T - S D D A S-20L ATA device - and should be HL-DT-ST-DVDRAM gsa-Y20L ATA device.
Same drive works in a Vista 64bit OS install and does show up as HL- and not the garbage H - . How can MS get away with and OS like Vista that is a piece of CRAP! I have spent money for a new drive and it shows up the same as the old one! HP is no help as the unit it OUT OF WARRANTY and wants $$ to even talk to me - even though ultimately it is HP's issue!

The dv6000 series notebooks are prone to all sorts of motherboard problems and failures, so may I cannot list all of them, it might be time to consider a newer notebook.
This is a user to user forum.

Creating a recovery drive for a K430 computer

Hello-I have a K430 desktop computer with a1TB HDD,12 GB Memory and Win8 64 bits. I used a !TB Seagate USB Drive for C drive backup and a 2GB Flash drive for Personal Document backup. I created a HDD image backup and a backup of my personal documents using the Lenovo procedure.. I understand that I need either a WIN8 disk or Recovery drive to boot and re-install my image file.
I am having problems creating a Recovery Drive. I formatted the drive to NTFS and verified that the Flash Drive was recognized by my computer. I searched for Recovery Drive.exe and it appeared. However, my flash drive did not appear on the Recovery window and the Next button remained greyed out. I will check and see if I have a recovery partition.Have you developed a fix for this problem? If so, please let me know. Thanks.
Carl W Lesesne

Updating Creating a recovery drive for a K430 Computer
Hello-I obtained a copy of Microsoft's Windows Create a USB recovery drive and discovered that I do not have a recovery partition. After entering recimg/showcurrent in a command prompt, I received a message stating that there is no active custom recovery image.
I attempted to create a recovery partition by entering mkdir C:\RefreshImage and recimg-Create C:\RefreshImage after the Command Prompt. This resulted in the following error message: recimg-createIMage is not recognized as an internal or external command. I have reported this problem to Microsoft also. If you are aware of a fix for this problem, please let me know. Thanks.
Carl W Lesesne

Need driver for combo drive px1055e-1nst

Similar Messages

Maybe you are looking for