Need hardware drivers (Only!) for NI PCI-DNET card, P/N 184726E-11. Do not need Labview run-time, Silverlight etc.

I need to install just the Windows XP hardware device drivers for my PCI-DNET card, P/N 184726E-11. Ordered under P/N 777358-01, the card is boxed with an installation CD-ROM. CD-ROM is NI-DNET for windows Ver 1.6.7. When the install app runs, it is trying to install all sorts of stuff I do not need - Labview Runtime, Microsoft Silverlight, Development Support, Automatic Updaters, etc. This card is being installed in a "production" machine. We have our own software, already developed, that talks to the card via the O/S. The hardware/device drivers are most certainly on the CD-ROM, I just need them identified and instructions for installing them.
Thanks,
Ed

Thank yor for the reply. However, it is not what I am looking for. The suggested download is 406MB. That's everything but MS Silverlight and the kitchen sink - overkill for our needs. We only need to install the Windows system driver for the card. We do not need Labview RT and the other development/support stuff for this installation. We have our own communications software that talks directly to the hardware, via the windows system driver. I have the 1.6.7 software CD-ROM, and need to know where the Windows sytem hardware driver/driver installer is located and what is the preferred method for installing only the hardware driver.
Thanks,
Ed.

Similar Messages

How do I set up a PCI-DNET card as master with A-B DNI as slave?

I'm trying to communicate with an Allen Bradley PLC through DeviceNet. I have a NI PCI-DNet card in my computer, and an Allen-Bradley 1761-NET-DNI interface between my PLC and the DeviceNet network. Does anyone know how to set up my National Instruments card as the Master of my PLC/DNI combination? Thanks in advance for the help.
Mark

Hi Mark:
The PCI-DNET card should set itself up as the master by default. As a matter of fact it should take more work to get it be the slave than to get it to be the master. Is this not what you are experiencing? Is there some sort of Allen-Bradley software that you have installed that is not allowing the NI board to be the master?
The DNET Manual states on page 4-8 that NI-DNET assumes that it is the only master in your DeviceNet system.
Emilie S.

Do I need Daq s/w while running a Labview exe which contains the DAQ hardware cards on a pc which does not have Labview s/w

I am having a Labview 6i program which takes hardware status from the NI hardware cards...now I make its exe with Labview Run Time Engine & then I am unistalling complete Labview with "Remove all" option....then I am installing this exe......Do I need DAQ or MAX now ?

Hello,
If you have an executable with DAQ functions in it, then you are required to have NI-DAQ installed on the machine.
Also, please post your LabVIEW/DAQ questions in the appropriate category...this category is for questions pertaining to the NI product "Measure for Windows", which you do not appear to be using.
Have a nice day,
Darren N.
Darren Nattinger, CLA
LabVIEW Artisan and Nugget Penman

I'm looking for a PCI UMTS card for Portege M700

First of all Hi everybody, as above mentioned in the title is about the Portege M700, I'm looking for a PCI UMTS card for this model have here a 8775 Sierra lying around, but this is unfortunately not recognized in Win7, I can times someone may say what card for this laptop is, or even something where I could get so ...???
Thanks apologize in advance

Hi
You need a 3G broadband module?
As far as I know some of the M700 Portege series have been equipped with the 3G module I think its from Novatel but Im not quit sure
However, if you need an part for the Toshiba notebook which would be compatible for sure, then the best place for buying such part is your ASP.
The guys could check what parts are compatible and could order it from Toshiba if this would be really necessary
Greets

Setting up PCI-DNET card to work with Eurotherm 2404 Controller w/Device Net

I have installed the NI PCI-DNET card in my PC running W2000 and the NI Measurement and Automation Explorer. I have also wired from the PC Card to a Eurotherm 2404 Controller with a Device Net Module and have terminated the connection with a 120 Ohm termination resistor. The baud rate and address have been configured on both ends to match, however although I am getting a good connection to the board I am not able to pick up the device when I run the "Simple Who" funtion. Any advice would be greatly appreciated.
Thank You

Hi,
When you say “…address have been configured on both ends to match”, do
you mean that you set the ‘Interface MAC ID’ of the dialog that comes
up when you start Simple Who to the one that is used by the Eurotherm
2404 Controller?
Simple Who is a master/scanner in a DeviceNet network, thus the
‘Interface MAC ID’ you configure is the one of the master, which must
not be identical to the one of any slave devices in the network. So,
try setting the ‘Interface MAC ID’ to a value other than the one used
by the Eurotherm 2404 Controller.
-B2k

Executable not working - Looking for LabVIEW Run-Time Engine

This has been one of those days.
I'm trying to create my .exe file to place onto another computer. I've done this before with success. But that was then and this is now.
I believe I have all the files I need in my LLB, and I believe I did my application distribution correctly and I believe I built the DLL correctly. But when I took the resulting .exe file and placed it on another computer and attempted to run it, it gave me the error message: "Unable to locate LabVIEW Run-Time Engine. Program requires a version 7.1 (or compatible) LabVIEW Run-Time engine. You should have already realized this, you moron."
Anyone have any idea where I went wrong or what step I might have missed? This has been a crazy, non-stop, massive brain fart of a day and I can't seem to remember what I'm missing here.
Amateur programmer for over 10 years!

Hi.
Whenever you want to use executables or .dll's created with LabVIEW you must make sure that the LabVIEW runtime engine of the SAME version as the LabVIEW version used to create the files, is installed in the target computer.
There are basically 2 ways to get the run-time engine installed on a computer:
1. (the one I prefer): Download the correct version of the LabVIEW run-time engine installer from www.ni.com/downloads, or more specifically from
http://digital.ni.com/softlib.nsf/websearch/369618104E25B08E86256F54006A4E2F?opendocument&node=132050_US
for the latest one. Once you have the installer for the run-time engine, just install it in the target computer. I prefer this option because the run-time engine is installed independently, so if you then uninstall your program, the run-time engine remains.
2. Create an installer for your program that includes the run-time engine. To include the run-time engine, when you are creating your application, go to the "installer settings" tab, click on "Advanced" and make sure there is a checkmark on "include LabVIEW run-time engine". This way when you install your program in the target computer, the run-time engine will also be installed.
Just as a note, any computer with LabVIEW on it, will also have the run-time engine.
Good luck.
Alejandro

System requirement for Labview run-time engine 8.6

Hello
is there any system requirements for LabVIEW Run-time engine 8.6? for example, same system requirements for LabVIEW 8.6? Internet Explorer 5 is fine? or Internet Explorer 6.0 or higher is fine? Does it work for Firefox on an Athena Linux mechine?
Thanks
Cynitha
Solved!
Go to Solution.

The system requirements can be found in the Release Notes. Pages 2 and 3 indicate the specific requirements for the Run-Time Engine per platform.

Setting parameters for synching pci-6534 cards via RTSI bus

I have been performing high-speed,
buffered, looping output with one pci-6534 card. I am now adding
a second 6534 card that I need to sync to the first card via the RTSI
bus. I have successfully used the RTSI bus to see the master REQ1
and ACK1 signals on those channels of the slave (seen at a connector
block), using the "RTSI control" vi. I simply set the master and
slave as transmitter and receiver, respectively, over the RTSI bus.
The question is: Once I have used the RTSI control vi to share the
necessary signals, do I need to do anything in my "dio config," "dio
write," or "dio start" vi's in the looping output code for the 2nd 6534
card to let it know that its REQ, ACK, STPTRG, and CLK signals are
coming from the bus? For example, in the buffered pattern looping
output vi, the "dio start" vi has choices of "internal" or "RTSI
connection" for its clock. My master board's code simply uses the
internal. Does my slave need to be set to RTSI connection, or,
once I have shared the clock signal over the RTSI bus, is that
effectively the internal clock for my slave too?
I apologize it this question is confusing. Unfortunately, so is the issue.

Hello bwz,
When you are performing synchronization across the RTSI bus you need to specify that the slave device should get its clock signals from there. You would use the digital clock config VI to do this. If you look in the example finder, you will find synchronization example VIs that do the same kind of thing for analog input. To find the examples, open the example finder by going to Help >> Find Examples >> Hardware Input and Output >> Traditional DAQ >> Multiple Device.
If you are just getting started developing your application, you may want to consider using DAQmx. There are many more examples available to look at for this type of synchronization. To find these examples in the example finder go to Hardware Input and Output >> DAQmx >> Synchronization >> Multi-Device. To use your PCI-6534 with NI-DAQmx, you must have version 7.4 or later. The newest version is DAQmx 7.5. You may also want to look at this tutorial about synchronization with DAQmx.
I hope this helps!
Laura

For Sale: PCI GPIB cards.

i have a couple of GPIB cards for sale from National Intruments
give me an offer if you are interested.

Thanks for the answer. Rev K and later for the older boards, and all new boards.
But then your documentation
is incorrect if you look at the "overview" section below the prices which seems to imply that OS 9 will work with this board. The description for the older TNT4882 based board is different and discusses only OS 9.
The description of the board is:
Name: NATI,pci-gpib
Type: ndrv
Bus: PCI
Slot: SLOT-4
Vendor ID: 0x1093
Device ID: 0xc801
Revision ID: 0x0001
And the only thing that changees is the last part that is the revision ID? Is the name field the same since that is what my driver uses to identify the board. I suppose I should change that to use the Dev
ice ID field. I am hoping that the NI DDK which my driver is based uses the "one chip mode" and will work equally well with both the TNT4882 and TNT5004 if you know anything about the NI GPIB DDK and the TNT5004 it would be most helpful.
Are their major differences internally for the PCI-GPIB/LP board so that the GPIB DDK based driver would not work with that? If so, does that have a PCI Name or Device ID that I can tell my driver to service.
Thanks again for the prompt answer.
>

Are drivers needed for USB2 PCI Express cards?

Most of the cards out there are made by companies that I've never heard of. Not necessarily a bad thing, but the lack of reviews makes it tough to choose. Although I don't really like Belkin, I'm leaning towards their card (it's nicely priced). The only problem is that they don't mention if it'll work in a Mac.
I would have assumed that it would be cross-platform, except that when I looked at their Firewire card it only mentions Windows.

You should probably check and see what MacSales (OWC) lists as well as xlr8yourmac.com which usually has reader reports, and don't forget MacIntouch (easy to search from my experience).
Aaxeon seems to be popular and supported, first heard of them with the PCIe G5s and is what OWC and FWDepot carries.
Mac Pro 2GHz 2GB WD Raptor/Caviar RE 320 Mac OS X (10.4.7) 2 x APC RS1500s

How do I install Netgear XE102 on my iMac? It will not install off of the cd provided it appears to be only for Windows based computers. Checked Netgear website and could not find a setup.exe file for Mac.

Unable to install Netgear XE102 on my iMac. Checked Netgear website and could not find a setup.exe file for Mac.

That means either no software needs to be installed on a Mac or the product is incompatible with Macs. Contact NetGear tech support for help.

How much storage space does a back-up drive need to run time machine on the 2TB iMac 2011?

I've just purchased a new 2011 iMac with 2TB storage...I have a G-Drive with 250 GB and I'm wondering the minimum size a back up hard drive must be to back-up my new hard drive using Time Machine. I already bought an Apple Router 2 years ago so buying the 3TB Time Capsule router/hard drive would be redundant. Any thoughts?

A very difficult question to answer, why because we don't know how much data you will have on your computer. As a general rule of thumb your TM drive should be 2-3x the size of the amount of data on your HD. So for example if you only have 100GB on your internal HD then your TM drive should be 200-300GB. So you need try to figure out approximately how much you will store on the internal HD. A good rule of thumb is how much did you store on your old computer. If I were you though I'd play it safe and use your G-Drive for something else, perhaps somewhere to store your photos, music or movies. Then go out and buy yourself a high quality 2-3TB EHD, why that big....simple because eventually all TM EHD's fill up. So by purchasing the largest EHD you can afford is simply putting off the inevitable by investing up front. There are three drives I recommend for a TM drive, one is the G-Tech series. They are a high quality with plenty of features. The others are:
OWC Mercury Elite Pro series
LaCie d2 Quadra series
Both are equally high quality with similar features to your G-Tech. Personally I use LaCie (I have 4 at the moment) however I wouldn't hesitate to use OWC or G-Tech either.

HT201209 Every time I type in the code for my iTunes gift card, it says the code is not properly activated.

I'm trying to redeem my iTunes gift card, and every time I type in the code, it says the code hasn't been properly activated.

Are you able to take it back to the store that you bought it from and ask them to activate it properly ? If not then you will need to try contacting iTunes Support (you will probably need to give them images of the front and back of the card, and possibly its receipt) : http://www.apple.com/support/itunes/contact/ - click on Contact iTunes Store Support on the right-hand side of the page, then iTunes Cards And Codes

I get an error message in yosemite saying I need java run time??

is Java necessary for yosemite

I went here http://www.oracle.com/technetwork/java/javase/downloads/jdk-7-netbeans-download- 432126.html and installed it for mac. Have to accept agreement 1st and now it is gone....yea

Do I need to run Time Machine if I have Time Capsule

I find that Time Machine slows me down. It runs a few times a day- maybe because I'm always stopping it. Do I need to do this? If not, how do I stop it from running. Thanks

Well...considering TM works in conjunction with TC...backing up files to your TC, I'd say you need it.
If you'd rather be sorry than safe, and not keep regular backups of your files, then turn TM off.

Need hardware drivers (Only!) for NI PCI-DNET card, P/N 184726E-11. Do not need Labview run-time, Silverlight etc.

Similar Messages

Maybe you are looking for