Need Help accessing Creative Coud Page

After trying to troubleshoot, I am at thoroughly fustrated. I get a blank page, and I cannot login or download. I have paid for my subscription and have confirmation. The creative cloud app page is blank with both browsers I use (IE and Chrome). I have turned of safe/protected browsing and set my security and privacy to low/medium...still blank. Can someone please help me?

Glad to hear things are working. If you have any issues with a blank page again please post or email me at [email protected]

Similar Messages

Need help accessing the router web page. I have been tol...

Need help accessing the router web page. I have been told my router is acting like a switch and the IP address is not in the proper range. I have tried reseting the router (hold for 30 sec and unplug for 5 mins). Didn't work.
thanks

What router are you using? Almost all Linksys routers use 192.168.1.1 as the default local IP address, but there is at least one that uses 192.168.16.1 , namely the WTR54GS (not the WRT54GS).
You need to try again to reset the router to factory defaults.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank (note: a few Linksys routers have a default user name of "admin" (with no quotes)), and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you.
Message Edited by toomanydonuts on 01-21-2008 04:40 AM

I need help on a main page. basic for u but not for me

Hello,
I need help on a main page.
I have this page called themainpage.cfm which someone here
asked me to make it the main page of my cf pages.
I have 2 pages right now in testing server.
Bloicpage.cfm
And
Index.cfm
When you go to
Server.myappfolders/repfolder
It let you go to
Server.myappfolders/rep/folder/ Bloicpage.cfm
Page.
I need for the themainpage.cfm to be the default when typing
Server.myappfolders/repfolder
Then have a link to the Bloicpage.cfm and a back button to go
back to the mainpage.cfm
Many thanks

here is the Bloicpage.cfm
which is currently the main page when you type
Server.myappfolders/repfolder
i need it to go to another main page which will have a link
to this and a back button from here and a back button from the
report html page and the excel csv page
ps .
i excluded the queries and some logics.
sorry
thanks
<cfparam name="form.ctcde" default="ALL">
<cfparam name="form.SDT" default="#now()#">
<cfparam name="form.EDT" default="#now()#">
<cfparam name="Form.outputFormat" default="CSV">
<cfsetting showdebugoutput="no"/>
<cfif not isdate(form.SDT)><cfset form.SDT =
now()></cfif>
<cfif not isdate(form.EDT)><cfset form.EDT =
now()></cfif>

<cfquery name="theQuery" datasource="cts9i">
SELECT
</cfswitch>
group by
Order by </cfquery>
<cfset a = a + 1>
</cfoutput>
<cfswitch expression="#Form.outputFormat#">
<cfc value="HTML">
<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0
Transitional//EN" "
http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
<html xmlns="
http://www.w3.org/1999/xhtml">
<head>
<meta http-equiv="Content-Type" content="text/html;
charset=iso-8859-1" />
<title>Untitled Document</title>
</head>
<style type="text/css">
table{
font-family:Arial, Helvetica, sans-serif;
font-size:85%;
td{
font-family:Arial, Helvetica, sans-serif;
font-size:85%;
th{
font-family:Arial, Helvetica, sans-serif;
font-size:85%;
h2{
font-family:Arial, Helvetica, sans-serif;
font-size:120%;
h3{
font-family:Arial, Helvetica, sans-serif;
font-size:100%;
</style>
<body>
<cfoutput>
<div align="center">
<h2>Bkc#dateformat(form.SDT,"mm/dd/yyyy")# to
#dateformat(form.EDT,"mm/dd/yyyy")# Wudd</h2>
</div>
<div align="center">
<h3>#form.ctcde# CCwoph</h3>
</div>
<table border="1" cellpadding="0" cellspacing="0">
<tr>
<th>ccc##</th>
<th>aaa</th>
<th>cccc</th>
<th>iii</th>
<th>Eee</th>
<th>h11</th>
<th>h112</th>
<th>h22</th>
<th>h222</th>
<th>h33</th>
<th>h333</th>
<th>ehh</th>
</tr>
<cfset variables.nphc = 0>
<cfloop index="x" from="1" to="#arraylen(anArray)#"
step="1">
<cfif NOT anArray[x][1]>
<tr>
<td>
#anArray[x][2].c_nbr#
</td>
<td>
#anArray[x][2].c_dcdt#
</td>
<td>
#anArray[x][2].PAPD#
</td>
<td>
#anArray[x][2].Iii#
</td>
<td>
#anArray[x][2].Eee#
</td>
<cfset thirdArray = anArray[x][3]>
<cfif NOT arraylen(thirdArray)>
<td> </td>
<td> </td>
<td> </td>
<td> </td>
<td> </td>
<td> </td>
<cfelse>
<cfloop index="z" from="1" to="3">
<cfif z GT arraylen(thirdArray)>
<td> </td>
<td> </td>
<cfelse>
<td>
#thirdArray[z][2]#
</td>
<td>
#thirdArray[z][3]#
</td>
</cfif>
</cfloop>
<cfif arrayLen(thirdArray) gt 3>
<td nowrap="nowrap">
<cfloop index="z" from="4"
to="#arraylen(thirdArray)#">
#thirdArray[z][2]# - #thirdArray[z][3]#<BR />
</cfloop>
</td>
</cfif>
</cfif>
</tr>
<cfset variables.nphct = variables.nphct + 1>
</cfif>
</cfloop>
</table>
Total Ccwoph: #variables.nphct#
<BR />
<BR />
<HR />
<BR />
<div align="center">
<h3>#form.ctcde# CWph</h3>
</div>
<table border="1" cellpadding="0" cellspacing="0">
<tr>
<th>ccc##</th>
<th>aaa</th>
<th>cccc</th>
<th>iii</th>
<th>Eee</th>
<th>h11</th>
<th>h112</th>
<th>h22</th>
<th>h222</th>
<th>h33</th>
<th>h333</th>
<th>ehh</th>
</tr>
<cfset variables.phc = 0>
<cfloop index="x" from="1" to="#arraylen(anArray)#"
step="1">
<cfif anArray[x][1]>
<tr>
<td>
#anArray[x][2].c_nbr#
</td>
<td>
#anArray[x][2].c_dcdt#
</td>
<td>
#anArray[x][2].PAPD#
</td>
<td>
#anArray[x][2].Iii#
</td>
<td>
#anArray[x][2].Eee#
</td>
<cfset thirdArray = anArray[x][3]>
<cfif NOT arraylen(thirdArray)>
<td> </td>
<td> </td>
<td> </td>
<td> </td>
<td> </td>
<td> </td>
<cfelse>
<cfloop index="z" from="1" to="3">
<cfif z GT arraylen(thirdArray)>
<td> </td>
<td> </td>
<cfelse>
<td>
#thirdArray[z][2]#
</td>
<td>
#thirdArray[z][3]#
</td>
</cfif>
</cfloop>
<cfif arrayLen(thirdArray) gt 3>
<td nowrap="nowrap">
<cfloop index="z" from="4"
to="#arraylen(thirdArray)#">
#thirdArray[z][2]# - #thirdArray[z][3]#<BR />
</cfloop>
</td>
</cfif>
</cfif>
</tr>
<cfset variables.phc = variables.phc + 1>
</cfif>
</cfloop>
</table>
Total Cwph: #variables.phc#

</cfoutput>
</body>
</html>
</cfc>
<cfc value="CSV">
<cfoutput>
<cfset variables.theOutput =
"Bkc#dateformat(form.SDT,"mm/dd/yyyy")# to
#dateformat(form.EDT,"mm/dd/yyyy")# Wudd">
<cfset variables.theOutput = variables.theOutput &
chr(10)>
<cfset variables.theOutput = variables.theOutput &
"#form.ctcde# CCwoph">
<cfset variables.theOutput = variables.theOutput &
chr(10)>
<cfset variables.theOutput = variables.theOutput & "C
##,Ad,Ccc,Iii,Eee,h11,h12,h22 ,h222,h33,H333,ehh">
<cfset variables.theOutput = variables.theOutput &
chr(10)>
<cfset variables.nphct = 0>
<cfloop index="x" from="1" to="#arraylen(anArray)#"
step="1">
<cfif NOT anArray[x][1]>
<cfset variables.theOutput = variables.theOutput &
"#anArray[x][2].c_nbr#, #anArray[x][2].c_dcdt#,
#anArray[x][2].PAPD#,#anArray[x][2].Iii#,#anArray[x][2].Eee#">
<cfset thirdArray = anArray[x][3]>
<cfif NOT arraylen(thirdArray)>
<cfset variables.theOutput = variables.theOutput &
",,,,,,">
<cfelse>
<cfloop index="z" from="1" to="3">
<cfif z GT arraylen(thirdArray)>
<cfset variables.theOutput = variables.theOutput &
",,">
<cfelse>
<cfset variables.theOutput = variables.theOutput &
",#thirdArray[z][2]#,#thirdArray[z][3]#">
</cfif>
</cfloop>
<cfif arrayLen(thirdArray) gt 3>
<cfloop index="z" from="4"
to="#arraylen(thirdArray)#">
<cfset variables.theOutput = variables.theOutput &
"#thirdArray[z][2]# - #thirdArray[z][3]# | ">
</cfloop>
</cfif>
</cfif>
<cfset variables.nphct = variables.nphct + 1>
<cfset variables.theOutput = variables.theOutput &
chr(10)>
</cfif>
</cfloop>
<cfset>
<cfset>
<cfset >
<cfset >
<cfset >
< & chr(10)>
</cfif>
</cfloop>
</cfoutput>
<cfcontent
type="application/msexcel"><cfoutput>#variables.theOutput#</cfoutput></cfc></cfswitch>

Need help to share Number/Pages file visa Mail option. Cannot do with iPad Air (iOS7)

Need help to share Number/Pages file visa Mail option. Cannot do with iPad Air

Oh, okay. After selecting the format I want to send, it says "creating... ". Then irrespective of the format I choose the message e.g. "creating spreadsheet" disappears, and so does the choice window (where I earlier chose Mail). I am taken back to the Numbers (or Page) where I had started from. Diavonex's note indicated that after "creating ... " stage I should be taken to an option where I can type in email address where I want to send the file, if I want to copy it to another address etc. I cannot arrive at that page - no matter whether I am working with Pages or Number, or which format I choose for the file to share !
I will try to close as you have suggested and try. However, I have switched on and off several times by now, but nothing changed!
Will look forward to any ideas to solve this !!!
Thanks much!
Best

I need help with a 1 Page Form with scrollable text field (5000 limit characters) and printing

Hello, I have no training in using Adobe Acrobat Pro or Livecycle Designer so I need major help with a 1 page form that I am attempting to create. Basically the form will be used to nominate employees for a Job Well Done Award.
The form contains the following:
1.) The name(s) of the employees being nominated and the date of the accomplishment.
2.) In the middle of the page I have a section for a write up, limited to 5000 characters, this is were I am needing the most help. A couple of things, about this section: The font is set at 11 and I don't want it to change. The text field has multiple-line, scroll long text enabled. The text field is a certain size and can only hold so much text, then it starts to scroll, which I am ok with, I like that feature. The issue I am having is during printing. I would like to keep the text field scrollable but when I print I would like to be able to print everything in that field. Executing this is the problem, I have no clue how to do it. I was hoping for some setting within Acrobat Pro or LiveCycle to be available, but the more I read and research this, it appears that it may require java, xml, basically some coding. I don't know for sure.
3.) Below the text field I have another field for the person nominating to type their name and right next to that another field for a digital signature.
4.) And finally below those two fields I have a Submit button that is setup to start email application so the form can be emailed to the proper inbox.
Thank you in advance.

With an Acrobat form the only thing you can do is export the text to
another location (like a blank field on another page) or to another file
format. With an LCD form you can expand the text box itself, but you'll
need to ask about that over at the LCD Scripting forum.

Need help with centering my page

I have done everything I can think of, including going through the many posts here to try and correct this with no luck
Please look at:
http://ebnerproductions.com
and
http://ebnerproductions.com/index2.htm
The first was built with basically just html.
The 2nd was done "properly" I believe with CSS and HTML. The 2nd also has "div - #wrapper"
left and right margins are auto also... nothing changed.
Do I need to change something in the CSS from absolute, to fixed or inherit?
I am completely lost at this point and really really need help.
Thank you again in advance....
Adam Ebner

Your CSS is corrupted -
:visited {
    color: #6CF;<meta name="keywords"
(note the appearance of the meta tag within the :visited selector)
Fix that.
Then you would need to add this rule to the fixed CSS by changing this -
body {
    background-color: #EBEBEB;
    background-image: url(BG.jpg);
    margin-left: 75px;
    margin-top: 75px;
    background-repeat: no-repeat;
to this -
body {
    background-color: #EBEBEB;
    background-image: url(BG.jpg);
    margin-left: 75px;
    margin-top: 75px;
    background-repeat: no-repeat;
    width:1346px;
    margin:75px auto;
Then ask yourself how many people will even see this page center since 1346 is way wider than the average browser viewport width on most systems.

Need help with Creative Cloud & Opening Illustrator

I recently purchased/downloaded Illustrator 6 and Photoshop through the Creative Cloud. It looks like I properly got Photshop into the programs, but not Illustrator. When I look it shows that I downloaded Illustrator, yet I cannot find the icon for it in programs. When I go into my control panel, programs and click on the icon it only asks if I want to uninstall. All I want to do is open the illustrator program to create some art. Where do I go?

You are welcome, Arlene.
With regard to the failure to find and open, you may (also) try Customer Care (tick I Still Need Help and hope for an agent available for a chat),
http://helpx.adobe.com/contact.html?product=illustrator&topic=downloading-installing-and-s etting-up
or this specialized forum (where you may be able find the answer from previous threads),
http://forums.adobe.com/community/download_install_setup
or Adobe Support (phone, where you may have to wait quite a while),
http://helpx.adobe.com/adobe-connect/adobe-connect-phone-numbers.html

Need help with a Purchased page on iPhone!

My iPhone cannot access the purchased page on iPhone App store. Some time it show up the list of app that I have purchased but I have to wait about 2-4 minues for that. Also many times that App Store just shut down automatic when I open Purchased pages. This have been happen since I updated my device to IOS6. I had try my friend ID from Japan and it perfectly work. So any way to solve this problem? Thank you.

I would say the iphone headset have 4 wires
left channel
right channel
mic in
ground
I would say an external mic being mono at least that all iphone support
would be 2 wires
mic in
ground
then I would take a apple headset and cannibalize it
there also are adaptors which change the apple headset into
2 normal std 3.5mm audio output connector
1 mono mic in connector you could chekc out those

Need help removing Creative Audio Control Panel

So I've been trying to get the Creative Consol Launcher to work with my soundcard again and found that in my "Programs and Features" list in windows 7 there is one item of Creative labs software that I can not remove. It is called "Creative Audio Control Panel" and when I attempt to uninstall it it tells me "C:\Program Files (x86)\InstallSheild Installation Information\{7E96A7F-AFE3-47-87B-583E37639E8}\SUPPORT.Cab not found."
Whenever I try to use the Creative Console Launcher it tells me "There are no supported audio device[sic] available. You need to close the application. Click OK to close the application now."? I assume it's trying to launch Creative Audio Control Panel which for some reason or other is no longer present on my system but was never properly uninstalled. Also, great work on that error message - seems like Creative needs more proof readers.
In other words it seems the file I need in order to uninstall this broken program is missing - any idea what I should do? I've tried seeing if I can reinstall the program but I can't find any setup file for it online - all I can find is "Creative Console Launcher" which seems to intigrate a launcher feature into volpannel, but since it doesn't have the Creative Audio Control Panel to actualy launch it just gives me error messages if I want to get into my EAX settings or mixer or anything like that. If anyone knows how I can uninstall/reinstlal this program (in windows 7) I'ld be very greatful.

Well I believe I have found a solution to my problem and it is manyfold so here goes.
First off, Creative Customer Support Americas corresponded with me via e-mail and notified me that there are known issues with all PCI cards and Creative Audio Consol in Windows 7 (which is to say they don't work together at all).
After getting this info I removed my SB 0790 card and plugged in another one I had handy - it's still a SB X-FI Xtreme Audio but this one is has a PCIe interface and a digital audio in/out jack on the back to boot - this card is manufactured not by Creative but by MSI (licenced I assume) and came with my motherboard (good thing I had it laying around).
Initialy I had the same issue - even uninstalling everything related to creative and re-installing the hotest newest drivers from the site simply wouldn't resolve the issue. Finaly I downloaded a 3rd party program called CCleaner - a freeware utility that can clean up registry errors and delete items off the program list by force if need be (and it was in this case). I used that to completely eradicate Creative Audio Console and Creative Console Launcher, re-installed the latest drivers and audio pack for the PCIe card, and then even had windows update the driver again after that (the result of which was not a new driver version but it did seem to download and install something - no clue what). After all of that I once again had a functioning version of Creative Audio Consol back on my computer - and now it recognizes that I have a valid card installed and I've got access to all the features I was missing. The interface for Creative Audio Console looks a bit different than it used to (no longer a fake looking stero but instead a fairly plane interface) but whatever it's working and that's what I care about.
Oddly enough with all those installs it never put Volume Panel or Creative Consol Launcher back on my computer, I wound up having to install those off of the MSI card's driver disk to get easy access to the Creative Audio Panel again (otherwise I'd have to either make a shortcut or go straight into the install directory any time I want to launch it - now though I can launch it right through the Volum Panel).
One persistant issue still remains: In my recording audio device list I am still missing: "What U Hear" but it has been this way since I installed Windows 7 for the first time in October when it releaed, and I have given up hope on ever seeing What U hear again - If I want to record from my soundcard I have a 3rd party freeware utility called "Virtual Audio Cables" that are a bit clunky but get the job done.
Conclusion:
Though it may claim on Creative's support page for the SB0790 (Sound Blaster X-FI Xtreme Audio) soundcard that the latest drivers support Windows 7 it is abundantly clear that this is NOT the case. You will manage to get audio out of it, but almost no other creative aplication is going to work with your card or even detect that a valid working SB card is installed. It seems the only aplication I could get working relyably was the auto updator (which was able to see I had the card installed) and Volume Panel. By the admission of Creative Customer Support America, however Creative Audio Panel will not work, and I have observed that Creative Consol Launcher does not function properly either. Indeed even plowing through the file system you'll find support only for XP and Vista versions of the drivers - there is no Win7 specific driver for either this card or it's PCIe counterpart.
Also don't expect to have access to the "What U Hear" utility - this goes for the PCIe version of the card as well. As ever, it seems the marketing guys are making claims about the card that can't actualy be backed up, sure it's techincaly illegal, but only if your customers are willing to start a class action lawsuit over a 50 dollar soundcard that sort-of works anyway.
Issue resolved for now - and I am no longer pulling my hair out in frustration.
Links to the Utilities I used to make my card functional:
CCleaner
http://www.ccleaner.com/
Virtual Audio Cables
http://software.muzychenko.net/eng/vac.html

Need help accessing PC's

I will be starting my Graduate School soon at a Fundamentalist seminary (www.bju.edu). Internet access here seems to be ultra filtered, and ultra blocked. I have a few questions about being able to access other computers on the Intranet.
I cant seem to be able to connect to other PC's via the normal GO - Network feature in Tiger, nor via the Connect to Server option. However on my Windows 98 laptop I can browse other workgroups.
Do I need to run a trial version of Dave? When I got my undergrad I attended a moderate Evangelical college, and they also had firewalls and Internet filtering, however they only really blocked, sex, ****, games, and other such ungodly sites. There I installed Dave and then I was able to access PC's on the network. But then again I was using OS 9.x at the time.
I thought OSX had PC network share browsing built in, but perhaps I thought wrong, and I need to install Dave.
All I know is that whatever they have installed or configured (seems to use Novell BorderManager) blocks Newsgroups, FTP, SSH, Telnet, IRC, gopher, AIM, AOL, Safari, and even Classic Internet apps, not including non supported operating systems (DOS, Windows 3.11, Windows 95, Windows CE, Mac OS 7-9, Unix, Linux, etc..).
I am not a networking expert, and perhaps the people here are, I am not sure.
Oh and I forgot that the Apple Software Update app and Quicken Direct Connect (run through Quicken software) are also blocked.
Just want to be able to access PC shares without buying Dave.
I have sent a few emails to IT, and perhaps they will be able to allow me to run Apple Software Update, Quicken Direct Connect, connect to my FTP Unix server (that I use for backups) and allow me to access my FTP web server, so I can update my website (without using Yahoo's web based option). Too bad I cant update each page via Claris Home Page like I can on a open network. But since OS 9 is not supported all apps that tunnel in that environment are blocked here, so I cant just edit one of my pages and click on the update icon here.
Thanks for the help on helping me access PC shares.
John

>I cant seem to be able to connect to other PC's via the normal GO - Network feature in Tiger, nor via the Connect to Server option. However on my Windows 98 laptop I can browse other workgroups.
Autodiscovery can be hit or miss, especially when dealing with multiple workgroups/domains and with filtered networks (the chances are that since the school is filtering so much traffic, they're probably also filtering some of the auto-discovery protocols).
However, that shouldn't prevent you from conecting if you know the IP address of the server you're trying to access. You can just enter smb://ip.address.of.server/sharename/ to connect directly, without using auto-discovery to find the servers.
>Oh and I forgot that the Apple Software Update app and Quicken Direct Connect (run through Quicken software) are also blocked.
IMHO, the network admins need to get a clue. Blocking important services such as Software Update means that you can't apply security updates to your system, potentially leaving you vulnerable. I'd guess that they don't block access to the Windows Update servers (or there'd be real trouble with all those hacked Windows machines), so they shouldn't block access to the Apple update servers, either.

Hard drive recently failed and iPhoto brings a -36 error when copying need help accessing image files

I recently updated my computer to mountain lion and after doing so my computer would no longer boot up. I took it to the apple store and they told me that the hard drive was damaged and needed to be replaced. They were booting my computer with an external drive and in doing so could access my computers HDD. Upon starting to drag and drop files to a new hard drive I started to get a lot of -36 errors. I proceeded to go go,e and create my own bootable thumb drive and try doing the same process with more time to look through it. I have up till now been able to copy most of my files but have run into a problem with iPhoto.
I have been searching around for a while now and have yet to find a method that helps me in my particular situation so I am now asking for help myself. I will explain what my current system of file recovery is and see if anyone can help me out.
I have since then replaced the HDD in my computer and purchased a SATA external HDD enclosure for the original drive. This allows me to still access all files and folders from the original drive. I have managed to recover a majority of the files but have recently run into a problem with the iPhoto library. Every time I try to drag and drop the iPhoto library to my new HDD it fails after "transferring" 2.02GB and tells me it has encountered a -36 error because some files cannot be read or written. I believe I am using iPhoto '09, I will check and confirm that later.
I am looking for a way to open iPhoto's library and access the image files it seems to be hiding from me. Please understand that I cannot open the iPhoto library either, I have lost access to the library entirely and want to see if there are any image files that I can save. I dont have the computer backed up recently and want to save my photos. Thanks for looking and I'm hoping someone can help.

Download iPhoto Library Manager and use its rebuild function. (In Library Manager it's the FIle -> Rebuild command). Rebuild it to the Pictures Folder. This might overcome the -36 issue.
(This will create an entirely new library. It will then copy (or try to) your photos and all the associated metadata and versions to this new Library, and arrange it as close as it can to what you had in the damaged Library. It does this based on information it finds in the iPhoto sharing mechanism - but that means that things not shared won't be there, so no slideshows, books or calendars, for instance - but it should get all your events, albums and keywords, faces and places back.
Because this process creates an entirely new library and leaves your old one untouched, it is non-destructive, and if you're not happy with the results you can simply return to your old one.)
Failing that you're into recovering your Originals from the damaged Library and creating a new Library and starting over from scratch.
Regards
TD

I need help in formating in Pages

I need formating help in Pages: I need two columns for text, but other text not in the columns. How do I do both?

Hi Mandy,
I'm not sure if I've understood what you want to do, but here's an example, based on what you've said. These instructions apply to a word processing document.
The Columns control button toward the right end of the format bar is used to set the number of columns. It's the dark one (indicating it's been selected) just above the top left corner of its menu in the image:
The 'other' text (I've called it 'extra text' in the image) can be placed in a text box. Click the T in the toolbar to insert a text box, resize to fit your 'other' text, and position as desired.
One recommendation I'd make to everyone learning to use Pages is to download and read through the first few chapters of the Pages '09 User Guide. Then check in the other chapters when you want to learn how to use specific features of Pags.
You'l find a download link in the Help menu in Pages.
Regards,
Barry

Need help combining docs in Pages or Preview--glitches

I'm trying to combine about 20 short docs into one, so it will print as one document. I've tried the following, and run into these problems:
1) Copying thumbnails in Pages. This works most of the time--however, every now and then, it will only copy one page of a multiple-page document. It doesn't seem to matter what/where I click, only the first page of the doc will copy over. This seems to happen every fourth document or so.
2) In Preview: tried combining PDFs by dragging and dropping from the sidebar. However, that created something that, while looking like a 38 page single document, still considered each document as separate. When I went to print, it would only print the document that was in the window.
3) In Preview: tried doing the drag-and-drop by dragging directly on to the page in the sidebar, instead of below or above (as recommended for Snow Leopard in a MacWorld article). Didn't work. The green plus sign appeared, but after I dragged and dropped, the new pages would disappear.
It would be incredibly helpful if I could solve this problem. I've combined a number of how-to sheets into a packet, and not being able to combine them into a single document means a very long night of collating!
Thanks for any help.
BTW, I'm on an iMac, Snow Leopard (10.6.8), Preview 5.0.3 and Pages 4.1.

When copying the Thumbnails in Pages '09 to paste into the Thumbnails of a 2nd document, they both must have the same page dimensions and orientation.
When selecting make sure you have all the sections selected (surrounded by a yellow border). Hold down the shift key and select a range or individual selections if need be.
I have tested this and it works. Even between Word Processing and Layout templates.
In Preview I tested the merge and yes there appears to be a bug, even after saving, then printing.
It is not just the two parts treated as separate however, it seems to drop pages at random. Some from the dragged over version and some from the original.
Possibly it is retaining only pages with different numbers, because it did not renumber them. I will test it further later on when I have time.
Peter

Time Capsule: Need help accessing my video surveillance DVR from the Internet.

I am using the latest 4th Generation Time Capsule attached to a DSL Modem. My 4 video Survilance DVR is connected to a switch then to the Time Capsule. How or what is needed to be able to access the DVR via the internet. I am able to access the DVR from within the home network only. Would appreciate some guidance.
Thanks in advance.

Is the modem bridged?
If not and working in router mode then the TC should be bridged.. this will never work if you have double NAT.
Whichever box is the main router will need to forward the required ports for the camera dvr.. does the software use port 80 ie html?? That means you just forward port 80 to the IP address of the dvr. But find out the port.. the dvr instructions should tell you. Port forwarding on the TC.. ain't hard.. just google for the instructions. If the dsl modem is router, read its manual.
You will need to lock the ip of the dvr so it doesn't shift. Do that in the router if possible but I am not sure you can on the TC. You will need to do it on the device using a static ip.
The other thing is public IP .. do you have a static public address.. if not you will need to run dyndns. this is not available in the TC.. as most things are not available. So you will also need to check the dvr remote access instructions as it might have a dyndns client.. or you will have to use dsl modem as router even if you currently bridge it.
Sorry this is making it complicated.
Give some feedback and we can go from there.
What is the main router?
What modem is it exactly?
What make and model is the DVR? A URL to the pdf manual will help if it gets complicated.
What port do you use to access the DVR?
Is there a dyndns client in the dvr?

Need help developing photo download page

I have a website for my daughter's high school band to
display the photos we take during band events. It is more of a
basic html table with 300x200 pixel images showing in 2 columns and
50 rows. We manually type the file name in the table cell (yes I
know its the hard way to do it, but it didn't take long to setup
either). Anyway, now I would like to have teh other band parents be
able to click on a check box for multiple images on a page and have
a download button at the bottom of the page. Then they can download
all the pictures. Except that I will also have on the site in a
different folder path but still following the same names and this
other would have the full size version (8 megapixel) of the image
and that is what the user would download - not the image in the
table cell.
Yes, I am aware that MySql files should be able to do this
but I have never developed a MySql file before nor a page
referencing it. All of mine have been with Access databases. The
current pages generally require a global search and replace for the
date that is the first part of the file name for the image and it
only takes baout 30 minutes fo me to update 7 pages of 50 photos.
Since this is volunteer work I would like to keep it quick and
easy.
Is there anyone who can help or point me to an online
tutorial or page example that I could draw from?
Thanks
George

I'm not sure this will work, but how about using javascript timer that is specified in the following link:
http://www.elated.com/articles/javascript-timers-with-settimeout-and-setinterval
Create a javascript function on your JSP page that when called, will do something like this:
function timeOutPage(){
setTimeout(timeOutPage(), 5000);
document.formName.submit();
}

Need Help accessing Creative Coud Page

Similar Messages

Maybe you are looking for