Need help. Activation after update iOS 5.1 is not working!!

Need Help in activating my iphone 4 after update iOS 5.1. My phone was been neverlock and i used its before update without any activations. After update i can't turn on my phone!!! On the display have message "SIM not valid. Only compatible SIM cards from a supported carrier may be used to activate iPhone. Please insert the SIM card that came with your iPhone or visit a supported carrier's store to receive replacement SIM card". But i haven't any sim cards. Only the sim card from my operator  "Kyivstar" (Ukraine)... What should i do?!
p.s.: sorry for my bad english, but i live in Ukraine, and we haven't autorized service center of Apple in our country. help me please.

You have been using a phone that has been hacked to allow it to be used on your network.  Upgrading your phone's software has relocked your phone to the original carrier. 
You will not be able to use your phone again unless the ORIGINAL carrier offers unlocking.  Many don't, and many who DO offer unlocking, will not unlock unless the phone has active service with the carrier in the appropriate country. 
You will need to find out who the carrier your phone is locked to is, and see if that carrier unlocks the phone.  It is very likely you will need to buy a new phone.

Similar Messages

  • My iphone 3gs is not active after update ios 6.1.2

    my iphone 3gs is not active after update ios 6.1.2
    plz ans. me....

    You can only purchase apps and other media for the county's sore in which yu are located. You account, included payment method, also must be associated with that country.
    Sam applies for updating apps. Note that not all apps are available in all country so y will not be able to update an app if you are in another country and that app is not available in that country or your account is not associated with that country.
    You can change the country and other things by:
    iOS: Changing the signed-in iTunes Store Apple ID account

  • After update, keyboard and trackpad does not work on MBA but wireless mouse works. I don't use a wireless keyboard. Stuck at login because need to enter pw. Anyone have this issue? Please help!

    My Macbook Air (13", mid 2011) right after I did the Maverick OS update. My keyboard on Macbook Air is not working and it says "There isn't a keyboard connected" (Bluetooth Keyboard Setup). I do not use a wireless keyboard. Apparently my bluetooth works because my wireless mouse works. I am currently stuck at my login screen not being able to get in because I can't even enter my password. I am, however, able to login as guests and get to the Keyboard viewer to type things with my wireless mouse. I really need my keyboard to work to use for my job. I need help please!

    I forgot to mention that my power button did work but everything else, keyboard and trackpad, didn't! Anyway, I shutdown my laptop, slept, and turned it back (in hopes that it might work instead of restarting it like before). Now my keyboard and trackpad works! Thank goodness! I was about to go to the Apple store upset too! 

  • Need Help...my wireless airport express will not work with my update of snow leopard

    after installing snow leopard on my macbook pro my airport express will not work...or will connect only for a minute at a time.

    If you mean by "airport express" the square airport router you plug in and has a usb port then run the Airport Utility located in your Utilities folder to set it up again. If AU doesn't see it you may need to do a re-set of the AE.

  • After update ios 7.1 Could not connect to App store

    Last night i updated my ipod 5g to  ios 7.1.But this morning i could not   connect to App store or iTunes Store.
    Any solutions??

    See what you did not yet do here
    Try the following to rule out a software problem:                 
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Power off and then back on your router
    .- Reset network settings: Settings>General>Reset>Reset Network Settings
    - iOS: Troubleshooting Wi-Fi networks and connections
    - Wi-Fi: Unable to connect to an 802.11n Wi-Fi network       
    - iOS: Recommended settings for Wi-Fi routers and access points
    - Restore from backup. See:
    iOS: How to back up
    - Restore to factory settings/new iOS device.
    If still problem and it does not connect to any networks make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
    Apple Retail Store - Genius Bar

  • After updating Adobe Flash, Firefox does not work

    I have Windows Vista.
    I just recently downloaded Firefox and it had that bar at the top of the internet url saying to update Adobe Flash or that the Adobe Flash plug in doesn't work. So I clicked on that and it took me to the Firefox site with the raccoon, with a list of things I might need to update.
    So I updates Adobe Flash to
    ActiveX: 11.4.402.278
    Plug-In Version: 11.4.402.278
    After that Firefox will open to my homepage which is the most visited with thumbnails of websites. But when I choose one, enter a website in the url, or click a favorite it fails to load.
    What do I do now?

    Thank you so much for responding to my question right away! You really helped me out. I've been so swamped in my school work and job I haven't had time to do anything else. Thanks alot for giving me a fast, straight to the point answer :) my problem is solved!

  • After update 3.1 - 3G does not work after phone sits idle

    Updated from 3.01 to 3.1 - went smoothly, no problems. Restored my latest backup without issue. All is good. A few minutes later I tried to make a call and it failed. I tried to access the web - failed. Rebooted phone comes up as expected. Made a call, access to web working. 10 minutes later tried to make another call - failed; access to web failed again too. Switched over to Edge, rebooted. Calls and web access work. Waited 10-15 minutes, tried again; Edge still working. Switched back to 3G, rebooted. Same issue - calls/web work initially but after a short time, all calls and web access fail. I went through the 3.1 restore process again -- started over like it was a new phone. Again, the update worked without any issues/errors. I was able to restore my backup and all was good. But, same 3G problems occurred. So just for fun, I ran the Iphone config utility and captured the console log during a phone reboot sequence. After the phone booted up calls and web access were working with 3G. Then, let the phone sit idle for a while and saw these event occur in the log; the first 5 entries were made when I successfully sent a text message. After that message was sent I let the phone sit for a while. The next couple of entries were interesting. After the 'deactivated PDP context' messages appeared I could no longer make calls or access the web with 3G. Anyone else see this?
    I never ever had this problem with 3.01 software.
    Sat Sep 12 09:04:58 unknown com.apple.SpringBoard[25] <Notice>: told to send sms 867
    Sat Sep 12 09:04:58 unknown CommCenter[29] <Notice>: queuing sms message with id 867
    Sat Sep 12 09:04:58 unknown SpringBoard[25] <Error>: mms: queued messageId 867
    Sat Sep 12 09:05:00 unknown com.apple.SpringBoard[25] <Notice>: internalID: [867]
    Sat Sep 12 09:05:00 unknown com.apple.SpringBoard[25] <Notice>: notifying clients of event: 2 (recordID: 867)
    Sat Sep 12 09:07:02 unknown CommCenter[29] <Notice>: Deactivating PDP context 1, because it has gone idle.
    Sat Sep 12 09:07:43 unknown CommCenter[29] <Notice>: Deactivated PDP context 1 that supports connection types 0x2
    Sat Sep 12 09:07:43 unknown configd[23] <Notice>: network configuration changed.
    Sat Sep 12 09:07:43 unknown configd[23] <Notice>: CaptiveNetworkSupport:CaptiveHandlePrimaryChanged:2034 new primary: 67DCB7A6-30F5-4ECE-8FBB-5FC1DA71276D on pdp_ip0

    I thought I'd post you a quick response because you described exactly the issues I was having. After my phone was idle for a while, my iPhone would refuse to get data over 3G.
    I've tested this thoroughly and I'm able to "trip up" the phone into a state where it can't download data from the 3G network. But turning airline mode on for about 30 seconds then off again resets forces a renegotiate with the cell tower/3g and everything seems to work again about a minute later.
    Nothing untoward listed in the console at this point either - The PDP context that you mentioned that was deactivated was more than likely the Internet Tethering. (It's usually PDP context 1, by the looks of things).
    I think I might switch off 3G and see if that helps until Apple fix this issue. It is related to the wifi issues that others have reported - As I've seen my iPhone unable to download information via 3G if wifi is turned on, but you don't connect to a wifi network. But I can't seem to reproduce this reliably.
    -Soen

  • After update Gedit and Epiphany plugins not working anymore

    Gedit and Epiphany plugins stopped working after recent update. They are listed in plugin dialog, but can't be enabled. Does anybody know how to solve this problem?

    I was able to successfully enable the plugins by re-compiling gedit using the ABS system.
    However, I do think this is a bug, and that we should report it.  I'm unfamiliar with that
    process as well.  If anyone can post a quick suggestion as to the best place to file a bug report,
    I would appreciate it :-)
    In the meantime, here's what I did.  This was my first time using the ABS system, so
    I went to http://wiki.archlinux.org/index.php/ABS All the below instructions are on the wiki,
    these instructions are specific to gedit:
    I installed abs using pacman.
    # pacman -Sy abs
    I edited /etc/abs.conf, and put a ! in front of the testing REPOS:
    REPOS=(core extra community !testing)
    As root, I ran
    # abs
    A bunch of stuff was downloaded to my /var/abs folder.
    I make a directory in my home folder for gedit's stuff:
    $ mkdir -p /home/yourusername/abs
    I copied gedit's stuff from /var/abs to my abs folder:
    $ cp -r /var/abs/extra/gedit/ ~/abs
      $ cd ~/abs/gedit
    I ran makepkg -s
    $ makepkg -s
    A bunch of stuff downloaded and compiled.  When it was done, there was a new gedit-2.24.3-1-i686.pkg.tar.gz file in the same directory.
    I told pacman to install the tar.gz file.  Note that I did not have to uninstall gedit.
    As root:
    # pacman -U gedit-2.24.3-1-i686.pkg.tar.gz
    And that was it!  I could then go into gedit and enable/disable whatever plugins I wanted.
    Hope this helps,

  • My 4s phone has gone black and just have an apple sitting on the screen. Have restore it 3 times after updating it and now will not work

    Have a 4S after udpating software I can no longer use it. Black scrren with apple log is all I have. Have restore it 3 times and it worked then had another small update and this is now what I am left with.

    Hey there janDkot1,
    It sounds like you are unable to boot your phone completely. I recommend resetting the phone with this process:
    To reset, press and hold both the Sleep/Wake and Home buttons for at least 10 seconds, until you see the Apple logo.
    From: Turn your iOS device off and on (restart) and reset
              http://support.apple.com/kb/ht1430
    If the phone still will not boot, I would next put it into recovery mode and restore the phone again with the steps in this article:
    If you can't update or restore your iOS device
    http://support.apple.com/kb/HT1808
    Thank you for using Apple Support Communities.
    All the very best,
    Sterling

  • Macbook pro 2012 does not work after update, macbook pro 2012 does not work after update

    After 6 weeks i started my macbook and installed q new update now it has a problem to start and restarts all the time again and again

    Make certain that your MBP is connected to an AC source and is charging or charged.
    Then try a SMC and PRAM resets:
    http://support.apple.com/kb/HT3964
    http://support.apple.com/kb/ht1379
    Ciao.

  • Need help unable to connect to the internet, ETHERNET not working, assigned IP address how to fix it on ethernet

    I am unable to connect my imac to the internet. I tried to connect direct to the ETHERNET, and I am having ip address assigned problem on ethernet and also on my airport extreme, it said no internet connection or no DNS server. Please help . My internet provider is brighthouse and I just have a technician guy come to check it out and they can't fix it either. I have other laptop and I connect the ethernet directly and it work for my other laptop so I know it is not the internet provider problem, but my IMAC doesn't work. I hope I don't have to do a full recovery on my imac as I have a lot of info need to backup and  I hope someone can help beside doing the full recovery.
    Thanks
    Carla

    Backup everything. Note that a bootable backup/clone is optimum. Then, reinstall the unnamed OS.
    iMac (27-inch Mid 2011), OS X Mavericks (10.9.3), SL & ML, G4 450 MP w/Leopard, 9.2.2

  • Urgent:Need help on UIX page in partial page rendering not working in Mozil

    Hi ,
    I have designed two page (customxslt and seedxlst)that have <form name="UploadXlst" usesUpload="true" method="get"> to upload the file.
    Base on a dropdown value yes or no on seedxlst i am calling other page customxslt .But when i click on submit button the page is not getting submitted.
    <submitButton data:text="UPLOAD_XLST@textSource"
    formName="UploadXlst"
    ctrl:event="fileupload" />
    This is only happening when i am using PPR to navigate to customxslt .
    BUt i am calling directly customxslt the page is getting submitted and code runs fine.
    please help me where i went wrong ..
    Edited by: user778145 on May 3, 2010 12:33 AM

    This is working fine in IE but not on Mozilla

  • After updating firefox ,Google search does not work

    when I get to the site, nothing will load

    Thanks for your response! I uploaded a screen shot of my Java Preferences window.
    I upgraded Firefox to 13 but Java still didn't work.

  • Can´t make any calls after updating IOS 8.2! Help

    Hello;
    Need help!
    I updated IOS 8.2 two days ago, and i cant make any calls since the update. I can only receive calls. and use data. I tried my simcard in the iPhone 5s without updated, and if worked.
    And i have two weeks that my icloud photos are still uploading to my iPhone 6.

    Hello yaritoon,
    Thanks for using Apple Support Communities.
    If you're unable to place calls, but you are able to recieve calls, then I'd like you to please follow through the troubleshooting in the article below in order to get this issue resolved.
    If you can't make or receive calls on your iPhone - Apple Support
    Have a great weekend,
    Alex H.

  • My iphone after updating ios  its stuck on  no  service and not activating iphone

    Any one who can helpme in this  i am facing problem activating  my iphone 3GS  after updating  IOS its stuck on  not activating  and no service plz help

    Did you buy a second hand phone?
    Was your phone ever locked to a different phone carrier than the one your on now?

Maybe you are looking for