Need help ASAP: No video card signal for neo4 plat

I just bought a new case, motherboard, ram, video card, power supply, and CPU. i took my drives from my old Dell and placed them into this case and the MSI neo4 plat. motherboard (specs at the bottom). after getting it to post, i noticed there was no video. i triple checked for anything that wasn't hooked up or loose. everything seemed good. i'm using a VGA monitor. i looked at the D-bracket 2 and noticed that it had 3 red lights and one green in the lower right hand corner. in the manual this means no video signal... well obviously. what does this mean and how can i fix it? my video card's fan is working. i see no spot for a PCI express power input. any ideas? i use my computer a lot and need to do some things before i leave for vacation on the 15th. i'd like to resolve any issues before i leave so i can relax about it when i get back.
thanks,
Zack

well it seems things have gotten worse, after taking out the ram the other day and putting it back in thinking it was a ram problem, which it turned out not to be, it is giving me a ram problem. i just snapped em in a few times in all possible configurations and nothing is changing.

Similar Messages

Need help on MS8808 video card

I have a Vanta / TNT2M64 video card (MS8808 Ver 1A) purchased from Techtronics here in western Canada. I accidentally shorted the card against my metal computer case while re-installing the card ..and now its dead. I put the old video card back in my computer, so I know the computer is still working fine, so I apparently caused an electrical problem on the MS8808 card. Can anyone suggest which component I may have fried, and if it can be replaced? Does anyone have a detailed component schematic for this card ..one that lists the details of each component? Thanks in advance for any help!!

Im running Hybrid SLI (Geforce Boost) on my Acer Aspire X1200 SFF with a Geforce 8200 (integrated) and a Geforce 8400 GS (add in) and notice no instability issues. (230 watt psu)
*******DISCLAIMER********
I am not an employee of BBY in any shape or form. All information presented in my replies or postings is my own opinion. It is up to you , the end user to determine the ultimate validity of any information presented on these forums.

Need help with 2nd video card ASAP

Hi, I have a new 2 X 2/8GHz Quad-Core Mac Pro and I need 3 monitors. I have the 8800GT card installed and recently added a 7300GT (card from previous mac pro). No luck with any output from the 7300. Can someone help me please?

< duplicate >

Can you help advise re video card upgrade for my G4 MDD?

Hello all. Just upgraded to Tiger from 10.2.8 a couple weeks ago. Should have done it long ago... like having a new computer! I want to get more out of the OS for mostly graphic apps like PS-CS2, Painter, Freehand, Fontographer, etc. Right now I have 1.5 GB of RAM & will probably max it out pretty soon.
No video or games (at least for near term). Have been doing homework by lurking here, studying mfr. sites & reading things like John Siracusa's great article (book) on arstechnica.com: "Mac OSX 10.4 Tiger". I spent a lot of last night digesting that. So I think I know what I want to do, but would appreciate opinions.
1. I'd like to get a graphics card that will get my G4 to Core Image-enabled. According to this -- http://www.apple.com/macosx/features/coreimage/ -- and other advice I've run across in these forums, I should probably get a Radeon 9800 (or 9600) Pro Mac Edition. The downside w this is just that they're currently not to be found at any dealers I've called or googled because of the AMD merger/backorder situation. Same goes for the 9600. Bummer. In the meantime I'm wondering if one of Nvidia models listed in the Apple page might work in my machine. Probably not... but does anyone know different? Here are the models listed:
nVidia GeForce FX Go 5200
nVidia GeForce FX 5200 Ultra
nVidia GeForce 6800 Ultra DDL
6800 GT DDL
I think I've seen most of these configured for AGP 4x, as I would need. Just don't know if any would fit into my G4... or if it would support the power requirements, heat levels, and so on that these things apparently generate.
2. I have another requirement besides just running Tiger happily. I have hundreds of fairly big image files that all still need a lot of work, for a book project I've been commissioned to do. Average file size around 200MB. And more than half of them are in a "Legacy" proprietary format used by an out of print app called Live Picture. So even just to convert all of them from that IVUE / FITS format scheme I still need either classic or 9.2 for a while. I can still do some things in L.P. better than in Photoshop.
It's a pretty interesting piece of software. The IVUE file is the base bitmap image. All corrections are in Vector layers on top. When done, the layers you want to apply are turned on and the final (or workaround buildout) is rendered as a TIFF, PS or stn file. (It also has a great prepress filtering engine to optimize cmyk for specific outputs). This app is VERY monitor drawing intensive - especially for layers with textures or selective color mods. When I was an early adopter in the program years ago, the developers constantly told us to do things like use as small a window as possible; turn off antialiasing unless really needed; build out intermediate IVUE's before collecting too many complex layers, and things like that. It has it's own VM system, and it does not like another Virtual Mem. running. Of course in Classic you can't turn off the OSX VM!
Development on this app stopped the arrival of OSX, and I think even before OS9! It was crash-prone back then, and of course is even more fussy in Classic. I can boot in OS9, but for some reason prefer the "security" of protected mode, since these new-fangled machines no longer have that civilized reset button.
So if I understand things properly, I want a graphics engine that will take the load off RAM for Quartz Extreme tasks. I've come to think that maxing RAM AND VRAM utilization will let me do more before the crash. Am I right?
Not necessarily the same needs as for Photoshop in Tiger; but for me right now this is my critical/important working environment, as this is a big paid project (it will be a vintage watch coffee table book - which draws from a couple of the world's notable private collections). It shouldn't be long before I'll be getting a MacPro anyway. Am sort of holding out for the sophomore edition, and Leopard.
What would you guys do? Thanks in advance for your consideration. I will greatly value your input.
Best regards,
Mike
G4 MDD 867, G4 Q'slvr 733 Mac OS X (10.4.8) also iBook G3 900 10.4.8 (G4 733 still running 10.2.8)
G4 MDD 867, G4 Q'slvr 733 Mac OS X (10.4.8) also iBook G3 900 10.4.8 (G4 733 still running 10.2.8)

Thanks very much for the info. Kind of what I thought.
Re their price gouging - Ouch! A 66% markup from retail, and they're refurbished. I think I can wait a month or so... of course if those cards were dc'd, I might consider it. But I talked to a guy at ATI, and he didn't give any such indication.
I did find a GeForce4 Ti4600 (NOS) for a pretty reasonable figure at another site, but that's an older, slower card. I'm impatient, so I'm tempted, but I think I'd be kicking myself if I didn't wait for the better solution.
Are you saying that I won't really do any better in Classic with the ATI, compared to my stock GeForce4 32MB? Forgot to mention I'm using a 22" Cinema (ADC), if that makes any difference. And I'll be running Classic probably on top of Jaguar (I installed Tiger on a fresh new second internal drive). I thought I'd skip mixing Classic with Tiger altogether, but when I booted up the first time, there it was in Sys. Pref's. I guess it saw OS9 on the other drive during install. That's sort of funny.
I guess my question is mostly answered. Will put up the flag shortly.
Thanks again.
Mike

Need help asap about point and shoot for inside

trying to take pictures for auction listings, don'thave a lot of experience. have been told about canon powershot and panasonic lumix - could you tell me what will be the easiest for me to use and give me the best inside pictures of objects to list - thanks!!!!

The key to getting a good picture is to make sure that you can control the light and less about the exact camera as long as you do not purchase any junk.
For auction images, you should invest in a small light box setup with multiple strobes/flashes that illuminte the item properly. In order to do this, then you should get an inexpensive SLR. You should also get a small tripod and remote shutter release that will allow you to make correctly focus pictures.
Currently, Nikon and Canon are head to head when it comes to image quality with Nikon edging out Canon since they have recently introduced some really great lenses. Sony is doing OK, but remember Canon and Nikon own 90 % of the camera market and the other 10% is left to everyone else. Sony is having some problems with ISO images that contain a lot more noise than Canon or Nikon.
Check out www.dpreview.com and www.luminous-landscape.com for reviews by photographers.
I do not work for Best Buy and am not affiliated with them in any way. I like HT and want to help people improve their HT experience. "There is a LOT more than just having a TV to make a home theater"

How do I reorder songs in a playlist in the new itunes??? I can no longer just click and drag. When I click, it doesn't move!!!! Need help ASAP- trying to prepare for an aerobics class and need songs in a specific order!

How do I reorder songs in a playlist in the new itunes??? I can no longer just click and drag. When I click, it doesn't move!!!! Need help ASAP- trying to prepare for an aerobics class and need songs in a specific order!

Vera,
Use View > View Options, and set 'Sort By" to "Manual Order."
Then you will be able to drag-n-drop songs up and down the list.

I'm trying to reinstall Logic Pro 9, and it says It's already installed. I have a project due for class and I need help asap. Please help!!!

I'm trying to reinstall Logic Pro 9, and it says It's already installed. I have a project due for class and I need help asap. Please help!!!

Yea I am. I deleted Logic Pro 9 and moved the App to the Trashcan like normal. Then when I go to install it, it says its already Installed. When I do this with other apps; it works fine, the install thing comes back up like it should once you have deleted the app

Stuttering flv playback issue- need help asap

We need help asap. Have a project is due to deliver today (5/14).
We have a video to go on a dvd-rom, live action with Motion Graphics behind.
When output is done thru Projector the Motion Graphics stutter as they scroll.
Here is more technical info:
Stuttering flv playback issue:
Prores 422 timeline 29.97fps 1280x720 output from fcp using current settings.
Mov file is approx 7gb, plays relatively smooth on a mac pro with no raid.
Frame by frame analysis shows all frames are present with no jumps tears or skips.
Tried several output paths, programs and settings to create a smooth flv file to no avail.
We adjusted data rates from 2k, 3.5k, 4k and 8k, no luck
We adjusted keyframe rates from low to all frames, no luck.
We tried cs3 flash encoder, cs5 media encoder, squeeze ect, same results.
Playback in the flash projector seems to choke slightly no matter what we do.
Have also posted in the Director Forum.
Any help much appreciated!

Here are a few ideas off the top of my head:
Try playing the file using a different xtra, sometimes different ones will work better. If you have Director 11.5, there is a native flv playback xtra.
You can build a player easily in Flash using the flvPlayback component, then bring that into Director as a swf.
Once you have the video in Director, try making the member Direct To Stage (DTS). If it is already DTS, try making it not DTS.
Make sure the video is not transparent, and nothing in Director overlaps the video... in fact, when the video is playing, nothing should be moving at all, and try to keep the amount of code that is running to a minimum.
Try lowering your video's data rate further or try using a different codec.
Using VBR (Variable Bit Rate) compression often makes the video appear to play smoother.
Try compressing the flv with different software. FFMpeg, for example, is free and does a very good job, often better than the Flash Video Encoder that comes with Flash/Creative Suite.

My Curve 9300 lost service need help ASAP

I lost all serivce on my blackberry curve 9300 and the only way I get service is if I go outside my house. Sometimes I get service in my house but it's for 5 seconds and then I get "searching for network" then it goes to "SOS" I need help ASAP.

yankeegirl32491 wrote:
My carrier won't do anything about it because I'm not an authorized user of the account which is stupid. I wasn't having a problem with service for about a year and yesterday my service just cuts out for no apparent reason.
Hello...well, that's a bit disconcerting...aiding and abetting what could be an unethical use of service...but I'm hopeful that there are further details that mitigate that suspicion. In any event, review this KB for perhaps helpful information:
KB03448 Network status indicator shows "SOS" on the BlackBerry smartphone
It is possible that they have a tower out, and you now are receiving service from a more distant tower, which does not have adequate signal strength to work through the walls of your house. But, sadly, there is no way for you to actually find out if such is the case or not.
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Premiere Pro CS6 keeps crashing when exporting h.264 (NEED HELP ASAP!)

Alright, so I have a video that I've probably rendered around 30 times now and it ALWAYS ends up either freezing up, and then Premiere stops working, or it just stops working.
I have a YouTube channel and I'm going away for 2 days tomorrow and I really need to get my videos up online, but I just can't render them! Does anyone know how to fix this? I really need help ASAP!
Here are my export settings.
http://imgur.com/ZgAuI4a,OMz4FEd,B8gjHws

While there are "some" Adobe employees who read/post here, this is primarily a user to user forum... NOT Adobe support
You are simply going to have to wait for someone to read your message, and look at your settings, and reply... IF that person has an idea (20 minutes is really not much time)
While you wait for someone to reply with ideas, some reading about your freezing problem... and questions to help people help you
1st, what are you editing?
Codec & Format information, with 2 links inside to read http://forums.adobe.com/thread/1270588
Report back with the codec details of your file, use the programs below... A screen shot works well to SHOW people what you are doing
http://forums.adobe.com/thread/592070?tstart=30 for screen shot instructions
Free programs to get file information for PC/Mac http://mediaarea.net/en/MediaInfo/Download
2nd, you need to give LOTS more information about your computer
-PPro Information FAQ http://forums.adobe.com/message/4200840
3rd, What is your exact brand/model graphics adapter (ATI or nVidia or ???)
What is your exact graphics adapter driver version?
Have you gone to the vendor web site to check for a newer driver?
For Windows, do NOT rely on Windows Update to have current driver information
-you need to go direct to the vendor web site and check updates for yourself
ATI Driver Autodetect http://support.amd.com/en-us/download/auto-detect-tool
nVidia Driver Downloads http://www.nvidia.com/Download/index.aspx?lang=en-us
4th, do you have Dual video adapters?
Go to the Windows Control Panel and select Hardware and Sound and then select Device Manager... In Device manager you click the + sign to the left of Display Adapters... and see if 2 are listed
-http://helpx.adobe.com/premiere-pro/kb/error---preludevideo-play-modules.html
-http://forums.adobe.com/thread/1001579
-Use BIOS http://forums.adobe.com/thread/1019004?tstart=0
-link to why http://forums.adobe.com/message/4685328
-http://www.anandtech.com/show/4839/mobile-gpu-faceoff-amd-dynamic-switchable-graphics-vs-n vidia-optimus-technology/2

Audio acting up in Premiere Pro | Need Help ASAP

Okay, I need help ASAP because this has been a serious issue for me.
So my source video (an interview) is on PR's timeline. I start playing it and it's working fine, but all of a sudden, the audio skips back to the beginning of the interview, then about 10 seconds later, it gets back on track. I checked the original video that I imported it from and it's all fine. I even reimported the file, but the problem persists.

Okay, problem solved. I took the working source video, took the audio out and put it in there.

What are the video card requirements for running a 23" cinema display

What are the video card requirements for running a 22" cinema display(clear acrylic case) w/ a PC? My motherbaord is AGP. Thanks to anyone who can help.
Intel P4 3.0ghz Windows XP

Hi Lionel,
As a general rule of thumb, the ATI Rage 128 Pro will not support a 20" LCD. That being said, there are reports of it doing just that (possibly the edition that went into the cube).
I'm not that familiar with the ins and outs of the Cube, so I can't give you authoritative information on it.
A good place to start looking for answers is:
http://cubeowner.com/kbase_2/
Cheers!
Karl

Need Help ASAP. Deleting Underline in Adobe Reader Touch.

I don't understand why it won't let me delete the strikeout or underline in my Adobe Reader Touch. There is no clear option when I highlight it and write click and the "Ctrl-delete" option is not working either. I need to get rid of both of these. Did them by mistake....simple task but so frustrated that I have spent 30+ minutes trying to figure this out. Please help.

thank you
ส่งจาก จดหมายของ Windows
จาก: ambersenos
ส่งเมื่อ: อา. 11 มกราคม 2558 21:23
ถึง: thang dinhvan
Need Help ASAP. Deleting Underline in Adobe Reader Touch.
created by ambersenos in Adobe Reader Touch for Windows 8 - View the full discussion
I don't understand why it won't let me delete the strikeout or underline in my Adobe Reader Touch. There is no clear option when I highlight it and write click and the "Ctrl-delete" option is not working either. I need to get rid of both of these. Did them by mistake....simple task but so frustrated that I have spent 30+ minutes trying to figure this out. Please help.
If the reply above answers your question, please take a moment to mark this answer as correct by visiting: https://forums.adobe.com/message/7085957#7085957 and clicking ‘Correct’ below the answer
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page:
Please note that the Adobe Forums do not accept email attachments. If you want to embed an image in your message please visit the thread in the forum and click the camera icon: https://forums.adobe.com/message/7085957#7085957
To unsubscribe from this thread, please visit the message page at , click "Following" at the top right, & "Stop Following"
Start a new discussion in Adobe Reader Touch for Windows 8 by email or at Adobe Community
For more information about maintaining your forum email notifications please go to https://forums.adobe.com/thread/1516624.

Objects outside of workspace show in SWF... Need help ASAP!

When I export a flash movie (.swf file)And play it on full screen, the objects that are outside of the workspace show. Can anyone tell me how to fish this problem? need help ASAP! Thanks :]

If what follows isn't sufficient for you to figure out, you'll have to spend some time learning how to work with Flash. While you'll often get help solving problems in these forums, it's less likely you will get tutoring services. Google is a very good resource for tutorials.
To create a mask you draw a shape to the size you want and place it on a layer above all the content you want to mask. A mask is actually not well named because masks normally hide things, while in the graphics world, masks define the are where things are shown... so when you apply a mask to something, only what is under the mask shows. To finalize, you right click on the label area of the mask's layer and select Mask from the menu that appears. You may have to drag lower layers up towards the mask layer to get them included, whicxh is why I mentioned creating the rest of the content as a movieclip (a single layer object).
To control the visibility of objects you set their visibility to true or false (AS2: mcName._visible = true (or false), AS3:mcName.visible = true (or false)).
To create a frame around the stage, add a new layer atop everything and draw a rectangle big enough to hide all the content you don't want showing that is off the stage. Then draw a rectangle that is the same size as the stage on top of that first rectangle, placing it over the stage, and then deselect anything that is selected. Then reselect the smaller rectangle you just drew and delete it. The larger rectangle is now framing your stage.

Error when extracting data with extractor 2lis_04_matnr - NEED HELP ASAP !!

Hi experts!
Got an error when extracting data with extractor 2lis_04_matnr.
System says (short dump):
DUMP TEXT START----
Runtime error:    CONNE_IMPORT_WRONG_COMP_TYPE
Exception:   CX_SY_IMPORT_MISMATCH_ERROR
Error when attempting to import object "MC04P_0MAT_TAB".
The current ABAP program "SAPLMCEX" had to be terminated because one of the statements could not be executed. This is probably due to an error in the ABAP program. When attempting to import data, it was discovered that the data type of the stored data was not the same as that specified in the program.
An exception occurred. This exception is dealt with in more detail below. The exception, which is assigned to the class 'CX_SY_IMPORT_MISMATCH_ERROR', was neither caught nor passed along using a RAISING clause, in the procedure "MCEX_BW_LO_API" "(FUNCTION)".
Since the caller of the procedure could not have expected this exception
to occur, the running program was terminated.
The reason for the exception is: When importing the object "MC04P_0MAT_TAB", the component no. 5 in the dataset has a different type from the corresponding component of the target object in the program "SAPLMCEX". <b>The data type is "D" in the dataset, but "C" in the program.</b>
DUMP TEXT END----
Please, can someone explain me how to solve it?
Really need help ASAP!
Thanks in advance,
Jaume
Message was edited by:
        Jaume Saumell
Message was edited by:
        Jaume Saumell

Hi,
Check this note: 328181
So you need to delete entries in SM13/LBWQ for application and also detup table content.
And then refill teh set up table.
If you are in production clear the entries by running collective run no of times for this application 04.
With rgds,
Anil Kumar Sharma .P

Need help ASAP: No video card signal for neo4 plat

Similar Messages

Maybe you are looking for