Need Help Configuring New AP Express N

Here's my current setup.
1. 1TB TC Dual Band (newest model)
2. 4 wireless G devices (2-Tivo's, PS3, iPhone)
3. 3 wireless N devices (2 MBP's, Mac Mini)
4. Airport Express N (AEn) (not yet configured or connected). New, still in the box.
I want to extend my wireless network because 1 of the N devices (Mac Mini) is in another couple rooms away from the TC and the reception is GREAT (5 bars), however the internet speed is poor and good (it fluctuates). Doing an internet SpeedTest it goes from 1 mbps to 14 mbps.
Questions:
1. Will the new AEn help with the internet speed for the Mini , if I use it to extend my network?
2. Will adding the AEn to my network drag down the other 2 N devices (slower network)?
2A. If yes by how much?
3. Will the AEn work in the N mode Only or Only mixed mode (a,g,n)?
4. Will the AEn cause problems with the TC because it's Dual Band?
Message was edited by: D/FW
Message was edited by: D/FW

1. Will the new AEn help with the internet speed for the Mini , if I use it to extend my network?
No. Using the 802.11n AirPort Express Base Station (AXn), will have no affect on your Internet connection speed. However, it should help your local wireless speed by providing a stronger signal to the Mac Mini.
2. Will adding the AEn to my network drag down the other 2 N devices (slower network)?
No.
3. Will the AEn work in the N mode ONLY or only mixed mode (a,g,n)?
The AXn is a single-band wireless router. It can operate in either the 2.4 or 5 GHz radio band at a time.
4. Will the AEn cause problems with the TC because it's Dual Band?
No. You can use the AXn to extend either the dual-band TC's 2.4 or 5 GHz radio.

Similar Messages

  • I need help configuring the Airport express from a PC

    Hi there!
    I want to configure the airport express from a PC. It runs okay but the connection is open (anyone can browse on my connection)
    In a PDF that I found on Apples web site, it says go to
    Start-> All programs-> Airport express setup assistant, but there are no programs named Airport on my PC!
    Do I have to download a utility for this purpose?
    Fredrik

    If all you want to do is add wireless security to an already configured Express, you'll probably want to use the Airport Admin Utility. You should be able to install it by installing this package:
    http://www.apple.com/support/downloads/airport42forwindows.html
    If the PC isn't running at least Windows XP, I think you're out of luck.

  • I need help getting new authorization codes for digital copies

    I need help getting new authorization codes for digital copies of movies. Can someone help me out?

    There's a lot of results in Google when you search for this but unfortunately refreshing the page doesn't seem to generate a different code anymore. Mine also says already redeemed

  • Need help opening new software application Adobe Elements 12 on my new MAC. HELP?

    Need help opening new software application Adobe Elements 12 on my new MAC. HELP?

    Is it installed? If so, go to Applications and choose either Adobe Elements 12 Organizer, or Adobe Photoshop Elements 12>Support Files>Photoshop Elements Editor.

  • Need help getting new printer hp deskjet 3520 setup for eprint and wireless

    need help getting new printer hp deskjet 23520 stup for eprint and wireless

    Hi Pastorlee7,
    I see that you're having problems setting up your printer.  I would take a look at the document below.
    Hp deskjet 3520
    Let me know how it goes.  

  • I need help configuring a connection with asdm 5.2 for asa

    Hi All
    I am very much a novice with asdm 5.2 for asa and I urgently need to configure a connection but don’t know how to. I have 2 domains at work and someone is trying to connect their sql client from their pc in one domain to the sql server in the other domain (DMZ).
    When he tries to connect he gets the error
    Cant connect to MySql Server at "IP Address" (10060)
    He is trying to connect on port 3306. Could anyone please give me any tips on how i can resolve this quickly? I know i am
    trying a shortcut on this one but I recently started a new job and thrown in the deep end here and need to learn this asdm 5.2 for asa product from scratch with nothing more than the manual that come with the cd . My Cisco knowledge is from 2001 when i did half of a ccna course.
    Any help would be greatly appreciated

    Hi,
    I'm not a security specialist but here is how I had it set up at home:
    Essentially a NAT and a rule forwarding the port are needed. In this particular case I had an Oracle server running and a person requested remote access. So, for example, the source address was his external IP and the destination was the Oracle's external IP. For the NAT the source was the internal IP of the Oracle server and the interface was Outside.
    Hope this points you in the right direction.

  • Need help configuring Excel Services

    I've configured both the Excel Serives and Secure Store Target applications and continually receive the following error message when trying to view the Simple Projects List sample report:
    An error occurred while accessing application id ProjectServerApplication from Secure Store Service. The following connections failed to refresh:
    Project Server - Simple Projects List
    The Server Logs show the following errors:
    Access Denied: Claims stored in the credentials did not match with the group claim for a group app.
    The Microsoft Secure Store Services application Secure Store Service failed to retrieve credentials.  The error returned was 'Access Denied.' ...
    Access is denied. (Fault Detail is equal to Microsoft.Office.SecureStoreService.Server.SecureStoreServiceFault)
    SSS has failed with the following exception: Access is denied.
    Unable to esablish a connection using credentials retrieved from SSS.  This could be because the Unattended Service Account is not configured or because the credentials retrieved from SSS are not valid. 
    I've repeated the steps to create these configurations a few times, and continue to get the same errors.  Any help would be appreciated!
    Thanks

    Hello,
    I need help setting up excel services.
    Excel service is already running on sharepoint server.
    I have one reporting file which is generated by DBA with database connection. i want to upload that file under document library and i want whenever user open it through document library, it gets updated through database connection 
    This is my first time, so pls guide me
    Reporting file has authentication set to --> None 
    Do i require any specific settings for authentication? like unattended account ? which username should i use
    Connection String -->
    Provider=SQLOLEDB.1;Integrated Security=SSPI;Persist Security Info=True;User ID=ExcelServices;Initial Catalog=SurveyData;Data Source=jdb1;Use Procedure for Prepare=1;Auto Translate=True;Packet Size=4096;Workstation ID=RSTKW7W-06709;Use Encryption for Data=False;Tag
    with column collation when possible=False
    http://../training/sptestsite/Medication_Audit_Report
    http://../training/sptestsite/Medication_Audit_Data_Connection_Library/
    Trusted File Location - is this place do i need to upload that reporting file? 
    Trusted Data Connection Libraries - is this place do i need to save connection file .odc ?
    If i am not wrong, should i put
    Trusted File Location = http://../training/sptestsite/Medication_Audit_Report
    Trusted Data Connection Libraries = http://../training/sptestsite/Medication_Audit_Data_Connection_Library/
    http://../training/sptestsite/Medication_Audit_Report -- Here only reporting file will be uploaded right?
    http://../training/sptestsite/Medication_Audit_Data_Connection_Library/ -- Here only database connection .odc file will be uploaded?
    what other settings are required. please correct me
    my email address - [email protected]
    Harsh

  • I need help configuring three products: WRVS4400N, WAG325N and WVC200

    Hello,
    I want your help in three linksys products as mentioned below:
    WAG325N ADSL2+ Router
    WVC200 PTZ CAMERA
    WRVS4400N VPN Router
    The computer connections and configuration of above linksys products which I am working with and which are connected with the above three linksys products at present are as follows:
    1) I have one server and one laptop.
    2) Laptop has two wireless adapters which I use to connect to the routers.
    3) The server is connected to the WRVS4400N Router through one of the four ethernet ports mentioned on backside of the WRVS4400N Router. The DHCP of this router is disabled by me and the router's default IP 192.168.1.1 was changed to 192.168.1.12
    4) The WRVS4400N router is connected to the Wag325N router for internet access to the server and server is connected to WRVS4400N Router as mentioned in point number 3 above.
    5) The WAG325N router is setup as per the instructions mentioned that came with the CD of this router. The only change that I have modified is the router's default IP. I have changed the default IP of WAG325N from 192.168.1.1 to 192.168.1.13 and DHCP is enabled on this router.
    The help that I want is step by step as follows:
    1) I want to configure the both routers in such a way so that I can access them from anywhere across the world i.e. remotely using internet.
    2) I have WVC200 Camera which I setup according to instructions mentioned in the CD and also configured the DDNS service. But when the " RJ45 Cable is connected " to my WAG325N router and Camera, then only the camera works properly. What I want is that after the setup is completed, I want to remove the RJ45 Cable connected from my camera to router and use the camera wirelessly from any location within the range of my above mentioned WAG325N router. I need flexibility to use my camera without cable connections from any location and any rooms of my house. I also configured the port forwarding and DDNS properly. The only problem is that if I remove the Cable after the setup of camera is finished, then the camera access is not working on LAN or internet(through DDNS). Whereas the same works on LAN and internet using the DDNS service, when the cable is physically connected to the WAG325N router. Also I want one more thing additionally other then this. I want to use this camera wirelessly by configuring the port forwarding options on both routers at a same time(i.e. simultaneously at once on WRVS4400N and WAG325N).
    3) Now as two DHCP cannot work at a same time and as my routers are connected with each other, So I have disabled the DHCP on WRVS4400N. Here I need help so that DHCP can be enabled on both at a same time. Because if the DHCP is not enabled on WRVS4400N then I have to give IP to the server which is connected with server. If I enable the DHCP then there are two DHCP's at a same time on same network and thus problems occurs in internet access to the server. So, what should I do in such a way so that I do not have to give any IP to my server and set it to automatic.
    4) This question is just for my knowledge so that I can use the above mentioned linksys purchases upto full extent possible in future. I want to know what is VPN and how is it usefull? What is the difference between VPN and VPN tunnel? How can VPN be used to access all my network resources connected with my server  in the above situation where my server is connected to WRVS4400N which in turn is connected to WAG325N?
    Thanks !
    Sincerely
    Kalpesh Sharma
    +91-79-25351208
    +919227435453
    Ahmedabad, India.

    for question number 1:
    you said that your main router is WAG325N, for you to remotely access the 2nd router is for you to forward the IP addr [192.168.1.12] on your first router and change its management port of your second router that is located on either the security tab or the administration tab on its User Interface
    to access your first router open and Internet Explorer and enter
    http://[public IP addr]:[management port]
    the PUBLIC IP or INTERNET IP is located on the status page of your router
    to access your second router just change the management port to
    ex.
    http://66.77.88.99:8080 first router
    http://66.77.88.99:8081 second router
    for question number 2:
    make sure that you have configured all wireless settings on both your camera and your main router WAG235N, once done save settings and power down your camera and power it back up.
    for question number 3:
    for you to enable DHCP on both routers your connection can go like so...
    from a regular port of your main router going to the INTERNET port of your second router [this way you can enable DHCP on both routers]. INTERNET is no problem, your cesond router will be able to get connection
    for question number 4:
    VPN - Virtual Private Network
    VPN tunnel -is/are connections from router to router [gateway to gateway]
    VPN is used to connect a diff network on a diff location for you to have access to the shared filed [it is like a file sharing through the internet]
    for you to be able to use VPN tunnel you have to connect to a different VPN router on a diff location. In that way you can get access to the other network 

  • Need to configure - 2 Airport Expresses, Macbook Pro + iMac G4

    Hi All. My problem is I can't get my G4 iMac to work with an Airport Express (connected to the ethernet port as the iMac doesn't have wireless.)
    Below (A) is a configuration that works and (B) doesn't.
    Configuration (A)
    Airport Express 1(Main) (living room) - Connected to DSL modem + sterio
    Airport Express 2 (bedroom) - Connected to USB printer
    I can happily play music via airtunes and print wirelessly to the printer from my MacBook Pro.
    Configuration (B)
    Same as (A) but an iMac is connected to Airport Express 2 in the bedroom by Ethernet Cable.
    The problem seems to be that the way Airport Express 2 is configured means the ethernet port isn't active. When I configure it to activate the port then I lose communication with it (from wireless Mac). The light goes from green to flashing amber. I can no longer see the printer from MacBook Pro.
    So the question really is, in order to have Configuration (B) fully working, what setting do I need to set on both airport expresses?
    Many thanks
    MacBook Pro   Mac OS X (10.4.8)   iMac G4 - 10.4.8

    WilH, Welcome to the discussion area!
    The Ethernet port on the AirPort Express (AX) is ONLY active when the AX is using WDS to join a wireless network.
    You will need to use the directions in KB 107454, AirPort Extreme and Express: Using WDS to create a network from multiple base stations to configure all of your AX. Configure AX1 as a "main base station". Configure AX2 and AX3 as remote base stations.

  • Need help for new message type for PO archiving

    Hello All
      I have configured new message type ZARR for PO archiving process. After configuring all the steps this condition is not getting picked to by itself. And after maintaing it manually it is giving red flag without any error message. Here I am listing all the step that I have followed for config. Please help me am I missing something or any parameter is wrong.
    Steps for new Message Type for PO Archiving
    1.     Defined new Table 513 Purch.Org./Plant.
    2.     Defined new access sequence Z513 Access Sequence for Archiving.
    Following are parameters to the Access Sequence
    Access Sequence Number = 21
    Table = 513
    Description = Purch.Org./Plant
    Requirement = 101
    Exclusive = Yes (box checked)
    3.     Maintain Output Type ZARR for PO
    General Data
    Access Sequence = Z513
    Access to condition (Checked)
    Multiple Issuing (Checked)
    Program = FM06AEND
    FORM Routine = CHANGE_FLAG
    Default Values
    Dispatch Time = Send Immediately (when saving application)
    Transmission Medium = Print Out
    Storage System
    Storage Mode = Archive Only
    Document Type = ARCHIVE
    Mail Title and texts
    Language = EN
    Title = Archiving for Legal Requirement
    Processing Routines
    Transmission Medium = 1 (Print Out)
    Program = SAPFM06P
    Form Routine = ENTRY_NEU
    Form = ZJ_9H_MEDRUCK
    Partner Roles
    Medium = Print Out
    Funct = VN
    Name = Vendor
    4.     Fine-Tuned Control: Purchase Order
    Oprat. = 1
    CType = ZARR
    Name = Testing for Archivin
    Short Text = New
    Update Print Related Data = Yes (checked)
    Oprat. = 2
    CType = ZARR
    Name = Testing for Archivin
    Short Text = Change
    Update Print Related Data = Yes (checked)
    5.     Maintain Message Determination Schema: Purchase Order
    Procedure RMBEF1
    Step = 100
    Cntr = 1
    CTyp = ZARR
    Description = Testing for Archivin
    Requirement = 101
    6.     Assign Schema to Purchase Order
    Procedure RMBEF1
    7.     Define Partner Roles for Purchase Order
    Out. = ZARR
    Med = 1 (Printout)
    Funct = VN
    Name = Testing for Archivin
    Name = Vendor
    8.     Test Condition Maintained in MN04 (Master Data)
    Purch. Org. = 0001
    Plant = 24
    Partner Funct = VN
    Medium = 1 (Printout)
    Date/Time = 4 Send immediately (when saving application)
    Output Device = HUL1
    Storage Mode = Archiving only
    Thanks
    Ankit

    the problem is the Exclusive = Yes  indicator in the access sequence.
    Your other message has this exclusive indicator as well.
    so if the first  message is found, then no other message wil be determined
    to allow several messages in one PO, you must not set this exlusive indicator

  • Need help with new itouch

    Please bare with me, while I 'try' to explain.
    I have my itunes account linked to my iphone and macbook. I have bought my daughter an itouch for Xmas. Now I have set up a seperate itunes account for her on my other Windows laptop. So she is able to purchase apps without them going and clogging up my itunes... NOW this is the bit i need help with...
    How can i transfer any music i have on my itunes to her itunes? and vice versa?
    Thanks in advance

    Right, I have now gone down the line of setting up a new user on my macbook, her own ID and then with the help of Mr google, I followed the steps of sharing my music, by moving my itunes media folder to a shared folder.
    Now i got my music on her itunes libary but when i did a test download of an app, it wont show in the library. I have even done the 'transfer purchases'. and its still not showing. I am slowing loosing the will to live with it! I really need help.

  • NEED Help Importing new Activities.

    Hi All,
    I am working on a project where I have been asked to add two new activities to all the 841 WBS codes belonging to the project. That means I have to add around 1600 new activities. So instead of going through the tedious task of adding those manually, I was wondering if there was an easier way like importing from Excel or anything else to do this. I need to finish this within this week, so I need help urgently.
    Please Help

    You can absolutely add new activities in via Excel import however how much easier this ultimately is depends on the structure of your project (ActIds, Codes, Relationships, etc) and the underlying data to be added.
    In a large project I have some exposure to Excel is used frequently to make activity level additions/changes, but the schedulers spent a decent amount of time early in the project re-naming activity ID's for grouping purposes (I believe specifically to help with excel imports).
    If your additions to each WBS follow any sort of consistent pattern then it may be quicker to use Excel. Even if it ends up not saving much time initially, at the very least you will have a process down for the next time you need to make major changes to your schedule.

  • Need help with new url address

    i'm very new to iweb and .mac - i've worked with websites before but never actually registered for a domain and need help setting up my iweb or .mac website with a new address.
    Can someone please help me with this...prices? where do i go? i just don't want to create a site for our student ministry at church without having a web/myname.com address.
    Thanks in advance!
    Chris

    You'll find there are a lot of good ones. Godaddy is one that I used to use. I am very happy with bluehost.com great prices and excellent service
    Produce | Shoot | Edit
    Take Two Visual Media
    http://www.take2vm.com

  • Need help buying new hard drive

    I have a macbook that needs a new hard drive and need help knowing what hard drives to buy that will be compatible with it. It is a macbook pro 17inch model no: A1297.
    Any help would be appreciated, Thanks

    Any 2.5" diameter, 9.5mm thick SATA drive will be compatible.  Currently they come up to 1.5 TB in capacity.  I have a 1 TB Seagate SSHD (hybrid) drive installed in my primary MBP.  The cost is a modest premium over a conventional HDD of the same capacity.  Boot and shutdown times are significantly faster when compared to a conventional HDD,  I can recommend this as an option.
    If the bank account permits, an SSD will produce the overall maximum performance gains.  Boot, shutdown and resource hungry applications will be noticeably faster.  Casualyll use such as e-mails and text editing will produce no meaningful performance differences compared to a conventional HDD.
    I am of the opinion that the cost premium is still too high for the benefits that they afford.  Other have different views.
    Ciao.

  • Forgot email and password. Need help! Newer mind g...

    Hello i need to get back my skype account and i dont know wich of my email is on that account becouse its been few years when i created account. Is it possible by using login nick name get back my account. For proof its my account i can tell ewerything what is on it. Please help!
    Newer mind got it back...

    Here are Two Ways to help you get your Gmail back click on both for the Info:  http://goo.gl/T9ot6   http://goo.gl/N6Ba0  b33

Maybe you are looking for

  • Edit image size in repeater

    hi, in my web i connect data by  http service. I 'm using repeater for loop.. But if i want to loop  image. I can't edit size image in repeater when i insert image. This  source <mx:HTTPService id="tintucRequest" url="http://localhost/webtintuc/tintu

  • Netctl: Using same ethernet interface for PPPoE and LAN

    Configuration overview One ethernet interface connected to a switch which has both the LAN and my ADSL router (running in bridge mode). My Arch PC should connect via PPPoE (possibly multiple connections) to the ISP and be able to access the LAN simul

  • V$archived_log and gv$archived_log

    2 node RAC on 10.2.0.4 Archived Logs stored in Local file systems of each node (not in ASM) To determine the amount of redo generated on each nodes I googled and got the below query. SELECT ROUND(SUM(blocks*block_size)/1024/1024/1024) arc_size, TRUNC

  • Row and Column Template in Hyperion Reporting

    Hi Whenver I am trying to save a column of a report as a template , it is giving an error : "The selected columns contain one or more of the items below that cannot be included in templates: Invalid Input " I am not sure what does this mean. Though I

  • Coldfusion Builder beta 2 won't install

    Howdy, october 15,2009, my cfbuilder beta 1 said the trial has run out. So I uninstalled it, and then reinstalled the beta 2. I have cfeclipse on my ganymede eclipse...it says that could effect my cf builder install, but it did not effect the beta 1