Need help fixing my router: WRT54G
I just got rid of Vonage and went back to this router. I tried puting in some firware and now everything is screwed up. I have no access to 192.168.1.1 to make any changes. Is there a way to clear everyhting out of the router and start over.
Message Edited by billyball on 07-19-2007 10:43 AM
Message Edited by billyball on 07-19-2007 11:03 AM
Things might not be as bad as it looks. This screenshot typically occurs when your browser is not getting a full connection to the router. Try the following:
To view the router's web pages:
Use Internet Explorer, it usually works.
JavaScript must be enabled.
Use a computer that is wired to the router.
In the non-working computer, temporarily turn off your software firewall. If you are using Zone Alarm, right click on the ZA icon in the system tray (lower right corner of screen) and then click "Shutdown ZoneAlarm", and see if this fixes your problem.
If you cannot get anything at 192.168.1.1 then perhaps this is not your router's address. Go to "Start" > All Programs > Accessories > Command Prompt.
A black DOS box will appear. Type in "ipconfig" (with no quotes), then hit the Enter key. Look at the "Default Gateway". Is it 192.168.1.1 ? Point your browser to the "Default Gateway", then login to your router.
Similar Messages
-
Need help accessing the router web page. I have been tol...
Need help accessing the router web page. I have been told my router is acting like a switch and the IP address is not in the proper range. I have tried reseting the router (hold for 30 sec and unplug for 5 mins). Didn't work.
thanksWhat router are you using? Almost all Linksys routers use 192.168.1.1 as the default local IP address, but there is at least one that uses 192.168.16.1 , namely the WTR54GS (not the WRT54GS).
You need to try again to reset the router to factory defaults.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank (note: a few Linksys routers have a default user name of "admin" (with no quotes)), and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you.
Message Edited by toomanydonuts on 01-21-2008 04:40 AM -
I did a manual restore but it gave me an error it was 3914 i need help fixing it.
i did a manual restore but it gave me an error it was 3914 i need help fixing it.
From this Apple support document: iTunes: Specific update-and-restore error messages and advanced troubleshooting
This device is not eligible for the requested build: Also sometimes displayed as an "error 3194." If you receive this alert, update to the latest version of iTunes. Third-party security software or router security settings can also cause this issue. To resolve this, follow Troubleshooting security software issues.
Downgrading to a previous version of iOS is not supported. If you have installed software to perform unauthorized modifications to your iOS device, that software may have redirected connections to the update server (gs.apple.com) within the Hosts file. First you must uninstall the unauthorized modification software from the computer, then edit out the "gs.apple.com" redirect from the hosts file, and then restart the computer for the host file changes to take affect. For steps to edit the Hosts file and allow iTunes to communicate with the update server, see iTunes: Troubleshooting iTunes Store on your computer, iPhone, iPad, or iPod—follow steps under the headingBlocked by configuration (Mac OS X / Windows) > Rebuild network information > The hosts file may also be blocking the iTunes Store. If you do not uninstall the unauthorized modification software prior to editing the hosts file, that software may automatically modify the hosts file again on restart. Also, using an older or modified .ipsw file can cause this issue. Try moving the current .ipsw file, or try restoring in a new user to ensure that iTunes downloads a new .ipsw.
Error 3194: Resolve error 3194 by updating to the latest version of iTunes. "This device is not eligible for the requested build" in the updater logs confirms this is the root of the issue. For more Error 3194 steps see: This device is not eligible for the requested build above.
B-rock -
Uloading ebook using iProducer rec'd error: ERROR ITMS-9000: "Unable to parse nav file: toc.ncx" at Book. I don't understand and need help fixing it. Please Help if you've the knowledge.
Many ThanksYep, i just did it again. The entire scroll-bar widget, complete with formatted text, graphics, etc., pasted itself nicely in another book. Two different files, the same widget.
I use the scroll-bar widgets for most of my texts. (I have audio buttons on the side, and the scripts are within the widget, to the side). My only text is within widgets, and text boxes, naturally.
I am following your recommendation: cleaning files, etc. I am remaking the book anew. I need to convince the EPUB bot or whatever that my file looks and works nicely on all my devices. You would expect an error message when previewing the book: 'Hey Amigo, your file is flawed, stop working on it, and get back to the drawing board." Should be able to try again next Monday. -
I deleted aperture and now my sistem is acting crazy.The dock disappeared and almost all icons are gone except for their names.I have an important project for tomorrow and I desperately need help fixing it.Can anyone help me please?
Well it all started with Aperture 3 trying to import some photos from my iphone.It took ages to import those photos and like I was in a hurry to finish my work in Illustrator so I tryied to force quit on A3 and it didn´t, so I shut down the computer and started over.it was all ok but I uninstalled the A3 and the I realized the icons were back to original form and a few fonts changed.so I Installed the trial version of A3.I did a restart of the system and then there was.aperture lauching but no dock and a 80% of the icons disappeared, but the names of the files and folder remained.and I cand acces the apps from the apple sign on the left corner.I tried also restarting a few time but it´s always the same.I am a recent user of a mac , and please excuse my bad english.If this is in any way useful please help me!
-
I need help fixing this... i can't get PDF to open
[2011-08-07:20:00:49] Launching subprocess with commandline c:\Program Files (x86)\Common Files\Adobe AIR\Versions\1.0\Resources\Adobe AIR Updater -installupdatecheck
[2011-08-07:20:00:49] Runtime Installer end with exit code 0
[2011-08-07:20:00:49] Runtime Installer begin with version 2.7.0.19530 on Windows 7 x86
[2011-08-07:20:00:49] Commandline is: -installupdatecheck
[2011-08-07:20:00:49] Installed runtime (2.7.0.19530) located at c:\Program Files (x86)\Common Files\Adobe AIR
[2011-08-07:20:00:49] Performing pingback request
[2011-08-07:20:00:50] Pingback request completed with HTTP status 200
[2011-08-07:20:00:50] Starting runtime background update check
[2011-08-07:20:00:50] Begin Background update download from http://airdownload.adobe.com/air/3/background/windows/x86/patch/2.7.0.19530/update
[2011-08-07:20:00:50] Unpackaging http://airdownload.adobe.com/air/3/background/windows/x86/patch/2.7.0.19530/update to C:\Users\Troy M\AppData\Roaming\Adobe\AIR\Updater\Background
[2011-08-07:20:00:50] Runtime update not available
[2011-08-07:20:00:50] Unpackaging cancelled
[2011-08-07:20:00:50] Runtime Installer end with exit code 0
[2011-08-07:20:01:23] Application Installer begin with version 2.7.0.19530 on Windows 7 x86
[2011-08-07:20:01:23] Commandline is: "C:\Users\Troy M\PamperedPartnerPlus\workspace\.report\SalesReceiptReport_08082011_010122AM.pdf"
[2011-08-07:20:01:23] Installed runtime (2.7.0.19530) located at c:\Program Files (x86)\Common Files\Adobe AIR
[2011-08-07:20:01:24] Unpackaging file:///C:/Users/Troy%20M/PamperedPartnerPlus/workspace/.report/SalesReceiptReport_080820 11_010122AM.pdf to C:\Users\Troy M\AppData\Local\Temp\fla54C3.tmp
[2011-08-07:20:01:24] Got an unexpected fatal error while unpackaging: [ErrorEvent type="error" bubbles=false cancelable=false eventPhase=2 text="not an AIR file" errorID=0]
[2011-08-07:20:01:29] Application Installer end with exit code 7
[2011-08-07:20:01:33] Runtime Installer begin with version 2.7.0.19530 on Windows 7 x86
[2011-08-07:20:01:33] Commandline is: -arp:uninstall
[2011-08-07:20:01:33] Installed runtime (2.7.0.19530) located at c:\Program Files (x86)\Common Files\Adobe AIR
[2011-08-07:20:01:37] Relaunching with elevation
[2011-08-07:20:01:37] Launching subprocess with commandline c:\program files (x86)\common files\adobe air\versions\1.0\resources\adobe air updater.exe -eu
[2011-08-07:20:01:37] Runtime Installer begin with version 2.7.0.19530 on Windows 7 x86
[2011-08-07:20:01:37] Commandline is: -stdio \\.\pipe\AIR_2996_0 -eu
[2011-08-07:20:01:37] Installed runtime (2.7.0.19530) located at c:\Program Files (x86)\Common Files\Adobe AIR
[2011-08-07:20:01:37] Starting runtime uninstall. Uninstalling runtime version 2.7.0.19530
[2011-08-07:20:01:37] Uninstalling product with GUID {FDB3B167-F4FA-461D-976F-286304A57B2A}
[2011-08-07:20:01:39] Runtime Installer end with exit code 0
[2011-08-07:20:01:39] Elevated install completed
[2011-08-07:20:01:39] Runtime Installer end with exit code 0
[2011-08-08:05:12:23] Runtime Installer begin with version 2.7.0.19530 on Windows 7 x86
[2011-08-08:05:12:23] Commandline is: -silent
[2011-08-08:05:12:23] No installed runtime detected
[2011-08-08:05:12:23] Starting silent runtime install. Installing runtime version 2.7.0.19530
[2011-08-08:05:12:24] Installing msi at c:\users\troym~1\appdata\local\temp\airb8a4.tmp\setup.msi with guid {FDB3B167-F4FA-461D-976F-286304A57B2A}
[2011-08-08:05:12:43] Runtime Installer end with exit code 0
[2011-08-08:05:14:53] Application Installer begin with version 2.7.0.19530 on Windows 7 x86
[2011-08-08:05:14:53] Commandline is: "C:\Users\Troy M\PamperedPartnerPlus\workspace\.report\SalesReceiptReport_08082011_101451AM.pdf"
[2011-08-08:05:14:53] Installed runtime (2.7.0.19530) located at c:\Program Files (x86)\Common Files\Adobe AIR
[2011-08-08:05:14:54] Unpackaging file:///C:/Users/Troy%20M/PamperedPartnerPlus/workspace/.report/SalesReceiptReport_080820 11_101451AM.pdf to C:\Users\Troy M\AppData\Local\Temp\fla1120.tmp
[2011-08-08:05:14:54] Got an unexpected fatal error while unpackaging: [ErrorEvent type="error" bubbles=false cancelable=false eventPhase=2 text="not an AIR file" errorID=0]
[2011-08-08:05:15:01] Application Installer end with exit code 7
[2011-08-08:05:16:11] Application Installer begin with version 2.7.0.19530 on Windows 7 x86
[2011-08-08:05:16:11] Commandline is: "C:\Users\Troy M\PamperedPartnerPlus\workspace\.report\ShowSummaryReport_08082011_101610AM.pdf"
[2011-08-08:05:16:11] Installed runtime (2.7.0.19530) located at c:\Program Files (x86)\Common Files\Adobe AIR
[2011-08-08:05:16:11] Unpackaging file:///C:/Users/Troy%20M/PamperedPartnerPlus/workspace/.report/ShowSummaryReport_0808201 1_101610AM.pdf to C:\Users\Troy M\AppData\Local\Temp\fla3F41.tmp
[2011-08-08:05:16:11] Got an unexpected fatal error while unpackaging: [ErrorEvent type="error" bubbles=false cancelable=false eventPhase=2 text="not an AIR file" errorID=0]
[2011-08-08:05:16:16] Application Installer end with exit code 7
[2011-08-08:06:29:43] Application Installer begin with version 2.7.0.19530 on Windows 7 x86
[2011-08-08:06:29:43] Commandline is: "C:\Users\Troy M\Documents\hs_11jul.pdf"
[2011-08-08:06:29:43] Installed runtime (2.7.0.19530) located at c:\Program Files (x86)\Common Files\Adobe AIR
[2011-08-08:06:29:44] Unpackaging file:///C:/Users/Troy%20M/Documents/hs_11jul.pdf to C:\Users\Troy M\AppData\Local\Temp\fla13FC.tmp
[2011-08-08:06:29:45] Got an unexpected fatal error while unpackaging: [ErrorEvent type="error" bubbles=false cancelable=false eventPhase=2 text="not an AIR file" errorID=0]
[2011-08-08:06:29:46] Application Installer end with exit code 7
[2011-08-08:06:30:25] Runtime Installer begin with version 2.7.0.19530 on Windows 7 x86
[2011-08-08:06:30:25] Commandline is:
[2011-08-08:06:30:25] Installed runtime (2.7.0.19530) located at c:\Program Files (x86)\Common Files\Adobe AIR
[2011-08-08:06:30:28] Launching subprocess with commandline c:\Program Files (x86)\Common Files\Adobe AIR\Versions\1.0\Resources\Adobe AIR Updater -installupdatecheck
[2011-08-08:06:30:28] Runtime Installer end with exit code 0
[2011-08-08:06:30:29] Runtime Installer begin with version 2.7.0.19530 on Windows 7 x86
[2011-08-08:06:30:29] Commandline is: -installupdatecheck
[2011-08-08:06:30:29] Installed runtime (2.7.0.19530) located at c:\Program Files (x86)\Common Files\Adobe AIR
[2011-08-08:06:30:29] Performing pingback request
[2011-08-08:06:30:29] Pingback request completed with HTTP status 200
[2011-08-08:06:30:29] Starting runtime background update check
[2011-08-08:06:30:29] Begin Background update download from http://airdownload.adobe.com/air/3/background/windows/x86/patch/2.7.0.19530/update
[2011-08-08:06:30:29] Unpackaging http://airdownload.adobe.com/air/3/background/windows/x86/patch/2.7.0.19530/update to C:\Users\Troy M\AppData\Roaming\Adobe\AIR\Updater\Background
[2011-08-08:06:30:30] Runtime update not available
[2011-08-08:06:30:30] Unpackaging cancelled
[2011-08-08:06:30:30] Runtime Installer end with exit code 0
[2011-08-08:06:31:02] Application Installer begin with version 2.7.0.19530 on Windows 7 x86
[2011-08-08:06:31:02] Commandline is: "C:\Users\Troy M\Documents\hs_11jul.pdf"
[2011-08-08:06:31:02] Installed runtime (2.7.0.19530) located at c:\Program Files (x86)\Common Files\Adobe AIR
[2011-08-08:06:31:02] Unpackaging file:///C:/Users/Troy%20M/Documents/hs_11jul.pdf to C:\Users\Troy M\AppData\Local\Temp\fla43F2.tmp
[2011-08-08:06:31:02] Got an unexpected fatal error while unpackaging: [ErrorEvent type="error" bubbles=false cancelable=false eventPhase=2 text="not an AIR file" errorID=0]
[2011-08-08:06:31:05] Application Installer end with exit code 7
[2011-08-08:06:31:08] Application Installer begin with version 2.7.0.19530 on Windows 7 x86
[2011-08-08:06:31:08] Commandline is: "C:\Users\Troy M\Documents\hs_11jul.pdf"
[2011-08-08:06:31:08] Installed runtime (2.7.0.19530) located at c:\Program Files (x86)\Common Files\Adobe AIR
[2011-08-08:06:31:08] Unpackaging file:///C:/Users/Troy%20M/Documents/hs_11jul.pdf to C:\Users\Troy M\AppData\Local\Temp\fla5C13.tmp
[2011-08-08:06:31:08] Got an unexpected fatal error while unpackaging: [ErrorEvent type="error" bubbles=false cancelable=false eventPhase=2 text="not an AIR file" errorID=0]
[2011-08-08:06:31:10] Application Installer end with exit code 7
[2011-08-08:06:31:25] Runtime Installer begin with version 2.7.0.19530 on Windows 7 x86
[2011-08-08:06:31:25] Commandline is: -arp:uninstall
[2011-08-08:06:31:25] Installed runtime (2.7.0.19530) located at c:\Program Files (x86)\Common Files\Adobe AIR
[2011-08-08:06:31:27] Runtime Installer end with exit code 6
[2011-08-08:06:32:54] Application Installer begin with version 2.7.0.19530 on Windows 7 x86
[2011-08-08:06:32:54] Commandline is: "C:\Users\Troy M\PamperedPartnerPlus\workspace\.report\ShowSummaryReport_08082011_113253AM.pdf"
[2011-08-08:06:32:54] Installed runtime (2.7.0.19530) located at c:\Program Files (x86)\Common Files\Adobe AIR
[2011-08-08:06:32:55] Unpackaging file:///C:/Users/Troy%20M/PamperedPartnerPlus/workspace/.report/ShowSummaryReport_0808201 1_113253AM.pdf to C:\Users\Troy M\AppData\Local\Temp\flaFB7D.tmp
[2011-08-08:06:32:55] Got an unexpected fatal error while unpackaging: [ErrorEvent type="error" bubbles=false cancelable=false eventPhase=2 text="not an AIR file" errorID=0]
[2011-08-08:06:34:32] Application Installer end with exit code 7
[2011-08-08:06:36:06] Application Installer begin with version 2.7.0.19530 on Windows 7 x86
[2011-08-08:06:36:06] Commandline is: "C:\Users\Troy M\PamperedPartnerPlus\workspace\.report\ShowSummaryReport_08082011_113606AM.pdf"
[2011-08-08:06:36:06] Installed runtime (2.7.0.19530) located at c:\Program Files (x86)\Common Files\Adobe AIR
[2011-08-08:06:36:06] Unpackaging file:///C:/Users/Troy%20M/PamperedPartnerPlus/workspace/.report/ShowSummaryReport_0808201 1_113606AM.pdf to C:\Users\Troy M\AppData\Local\Temp\flaE83C.tmp
[2011-08-08:06:36:06] Got an unexpected fatal error while unpackaging: [ErrorEvent type="error" bubbles=false cancelable=false eventPhase=2 text="not an AIR file" errorID=0]
[2011-08-08:06:36:08] Application Installer end with exit code 7
[2011-08-08:06:40:11] Application Installer begin with version 2.7.0.19530 on Windows 7 x86
[2011-08-08:06:40:11] Commandline is: "C:\Users\Troy M\PamperedPartnerPlus\workspace\.report\ShowSummaryReport_08082011_114010AM.pdf"
[2011-08-08:06:40:11] Installed runtime (2.7.0.19530) located at c:\Program Files (x86)\Common Files\Adobe AIR
[2011-08-08:06:40:11] Unpackaging file:///C:/Users/Troy%20M/PamperedPartnerPlus/workspace/.report/ShowSummaryReport_0808201 1_114010AM.pdf to C:\Users\Troy M\AppData\Local\Temp\flaA488.tmp
[2011-08-08:06:40:11] Got an unexpected fatal error while unpackaging: [ErrorEvent type="error" bubbles=false cancelable=false eventPhase=2 text="not an AIR file" errorID=0]
[2011-08-08:06:40:17] Application Installer end with exit code 7
[2011-08-08:06:41:40] Application Installer begin with version 2.7.0.19530 on Windows 7 x86
[2011-08-08:06:41:40] Commandline is: "C:\Users\Troy M\PamperedPartnerPlus\workspace\.report\SalesReceiptReport_08082011_114140AM.pdf"
[2011-08-08:06:41:40] Installed runtime (2.7.0.19530) located at c:\Program Files (x86)\Common Files\Adobe AIR
[2011-08-08:06:41:40] Unpackaging file:///C:/Users/Troy%20M/PamperedPartnerPlus/workspace/.report/SalesReceiptReport_080820 11_114140AM.pdf to C:\Users\Troy M\AppData\Local\Temp\fla138.tmp
[2011-08-08:06:41:41] Got an unexpected fatal error while unpackaging: [ErrorEvent type="error" bubbles=false cancelable=false eventPhase=2 text="not an AIR file" errorID=0]
[2011-08-08:06:42:57] Application Installer begin with version 2.7.0.19530 on Windows 7 x86
[2011-08-08:06:42:57] Commandline is: "C:\Users\Troy M\PamperedPartnerPlus\workspace\.report\SalesReceiptReport_08082011_114257AM.pdf"
[2011-08-08:06:42:57] Installed runtime (2.7.0.19530) located at c:\Program Files (x86)\Common Files\Adobe AIR
[2011-08-08:06:42:57] Unpackaging file:///C:/Users/Troy%20M/PamperedPartnerPlus/workspace/.report/SalesReceiptReport_080820 11_114257AM.pdf to C:\Users\Troy M\AppData\Local\Temp\fla2E11.tmp
[2011-08-08:06:42:58] Got an unexpected fatal error while unpackaging: [ErrorEvent type="error" bubbles=false cancelable=false eventPhase=2 text="not an AIR file" errorID=0]
[2011-08-08:06:43:02] Application Installer end with exit code 7
[2011-08-08:06:44:48] Application Installer end with exit code 7i have reader... and this is the error message i get when i attempt to open one
sorry, an error has occured.
The application could not be installed because the installer file is damaged. Try obtaining a new installer file from the application author.
Date: Mon, 8 Aug 2011 11:19:37 -0600
From: [email protected]
To: [email protected]
Subject: I need help fixing this... i can't get PDF to open
To open files with the .pdf extension, please use http://get.adobe.com/reader/.
Thanks,
Chris
> -
I need help with my shockwave flash it is crashed i need help fixing
I need help with shockwave flash it is crash i need help fixing it
http://forums.adobe.com/thread/1195540
-
I need help fixing kernel panic asap please help
i need help fixing kernel panic asap please help
OS X- About kernel panics
Mac OS X- How to log a kernel panic
Post a copy of your most recent complete panic log. -
I need help fixing itunes crashes on my old mac
i need help fixing itunes crashes on my old mac
Thanks for your reply,
I have both the silver discs specific to my iMac and Mac Pro models that you receive with your Mac, and a general copy of Snow Leopard that you buy from the store.
I used the silver disc that is specific for my iMac to install the drivers, and Boot Camp 3.0 on my iMac. But with the Mac Pro, the software is older and only has Boot Camp 2.0, thus I'm wondering if I can simply use the software on the general copy of Snow Leopard I own, or does the silver disc contain specific drivers for my Mac Pro that I need?
I'm under perhaps the wrong impression that the silver discs that you get with your Mac purchase contain drivers for your specific Mac model which you can't get from the general Snow Leopard disc.
Thanks. -
HT1725 Helo I need help fixing my I-tune account. Anyone out there?
Hello I need Help fixing my I tune account is anyone out there?
You do not state your issue...
KHarenda wrote:
... I need Help fixing my I tune account ...
To Contact iTunes Customer Service and request assistance
Use this Link > Apple Support iTunes Store Contact -
I need help fixing my iPod Touch 4th Generation myself
I have an iPod Touch 4th Generation and the home button isn't working i think its stuck problem is my warranty expired and i have no money to fix it so i need help fixing it myself again my warranty expired and i have no money to fix it so HELP PLEASE
Try:
fix for Home button
iPhone Home Button Not Working or Unresponsive? Try This Fix
- If you have iOS 5 and later you can turn on Assistive Touch it add the Home and other buttons to the iPods screen. Settings>General>Accessibility>Assistive Touch
- If not under warranty Apple will exchange your iPod for a refurbished one for:
Apple - Support - iPod - Repair pricing
You can do it an an Apple store by:
Apple Retail Store - Genius Bar
or sent it in to Apple. See:
Apple - Support - iPod - Service FAQ
- There are third-party places like the following that will repair the Home button. Google for more.
iPhone Repair, Service & Parts: iPod Touch, iPad, MacBook Pro Screens -
When trying to install Pro Tools 10.3.3 Aid Virtual Instruments I get a warning no mountable file systems. I need help fixing the problem.
Thanks Linc for responding to my post. I searched a little further and found I was missing a file. Once I downloaded the fix, I was able to install the software from the original download.
-
Well my ipod 4th gen was updated it shut off and now when i try to turn it on it stays on the apple logo for abit then gets stuck on a white screen od blue or mixed colores i really need help fixing this plzz help
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
Need help on which router to buy for my BB 8320
Now i know 8320 is dated but at this point i am not planning to change anytime soon .
So I have a router which is kinda old, it didnt really occur to me since it worked. When i got my bb 8320 i was in a hotel and i could connect through their wireless without any hassle. I could surf, use youtube, name it.
When i got home i couldnt do anything, i spent countless nights trying to figure out waht was wrong then i realized its my router. If only BB said somethign it wont support old routers then i wouldve saved myself hours of self-loathing.
Anyways I also have gone to my friends house, and i could connect to her linksys router without any hassle. i was the one who set her router up and we bought it this year. i didnt do anything special, configuration-wise or w/e.
So NOW i am just going to buy a new router. I really need help!!!!
I was wondering if this one is good:
W311R Wireless-N Broadband Router
W311R integrates the wireless AP, router, four-port switch and firewall in one, and increases over 4 times transmission range of ordinary 802.11g products. Compatible with IEEE802.11n (Draft 2.0) and IEEE802.11g/b standards, it can provide up to 150Mbps stable transmission rate. It is dedicated to SOHOs and students’ dormitory. In addition, URL and MAC address filtering can take it easy for parents and network administrator to manage network life, and QoS bandwidth control over specific computer’s downloading speed is supported as well. Moreover, UPnP and WMM support can smooth your MSN voice better, and the included Setup Wizard on CD-ROM will be easy and fast for non-savvy users to install the device and access to the Internet.
Overview:
* Includes router, wireless access point, four-port switch and firewall in one
* Provides up to 150Mbps uploading and downloading speed
* Supports two WPS (Wi-Fi Protected Setup) encryption methods: PBC and PIN
* Compliant to IEEE802.11n, IEEE802.11g, IEEE802.11b, IEEE802.3 and IEEE802.3u standards
* Supports far-distance transmission, 100 meters indoor, 400 meters outdoor (depends on the environments around)
* Supports 64/128-bit WEP encryption, WPA and the latest WPA2 encryption security authentication
* Supports RTS/CTS protocol and data partitioning function
* Provides one 10/100Mbps Auto-Negotiation Ethernet WAN ports for WAN connection
* Provides four 10/100Mbps Auto-Negotiation Ethernet LAN ports for LAN connections
* Supports xDSL/Cable MODEM, static and dynamic IP in community networking
* Supports remote/local Web management
* Supports WMM to better smooth your voice and video
* Supports SSID stealth mode and access control based over MAC address (up to 30 entries)
* Supports Auto MDI/MDIX
* Supports wireless Roaming technology and ensures high-efficient wireless connections
* Supports auto negotiation/manual mode for 802.11b/802.11g/802.11n
* Supports UPnP and DDNS
* Supports Firefox 1.0, IE5.5 or above
* Supports SNTP
* Supports virtual server, DMZ host
* Built-in firewall for hacker’s attack prevention
* Supports DHCP server/client
* Supports auto wireless channel selection
* Supports the control over LAN access to Internet
* Provides syslog to record the status of the router
* Supports WDS wireless network extension
* Supports QoS function
Input Voltage Range
AC 110~240V
Output Voltage Range
9V~1000mA
Consumption
20dbm
Operating Temperature
0? ~ 40?
Storage Temperature
-40? ~ 70?
Operating Humidity
10% ~ 90% RH non-condensing
Storage Humidity
5% ~ 90% RH non-condensing
Antenna
One Non-detachable external antenna (5dBi)
Frequency Range
2.4GHz-2.5GHz
EVM
-30dB
Sensitivity
54M:-74dBm@10% PER; 11M:-85dBm@8% PER; 6M:-88dBm@10% PER; 1M:-90dBm@8% PER
Outdoor
400m
Indoor
100m
WLAN?LAN
93Mbps
WLAN?WLAN
93Mbps
Frequency Range
2.4GHz
Gain
5dBi
Nominal Impedance
50
Polarization
Linear; Vertical
Maximum Power
1W
* Vertical Beamwidth 360ºFlip UltraHD.
Shoots mp4 H264 format files. Fits in a shirt pocket and records 2 hrs worth of material to an internal card. Charges from your USB port as you download. If you are just trimming clips, you can use QT Pro without conversion. If you need to edit, convert to ProRes 720p30. Works like a dream.
Just make sure you have it solidly placed when you pull the trigger as there is no image stabilization.
Oh, and it is only $199 US.
x -
I'm currently working on a problem for school where you have to make a game called Pig.
I worked on it but need help on fixing it because it won't work the way I want it to, and I'm not sure what the problem is.
public class Pig
public static void main (String[] args)
int num1, num2, num3 = 0, num4, num5, num6 =0;
String answer="y";
PairOfDice die1 = new PairOfDice(); // die # 1
PairOfDice die2 = new PairOfDice(); // die # 2
while (num3 <= 100 || num6 <= 100)
// rolls dice
while (answer.equalsIgnoreCase("y"))
num1 = die1.roll();
num2 = die2.roll();
if (num1 == 1 || num2 == 1) // when either face is 1
{num3 = num3;
answer = "n";}
else
if (num1 == 1 && num2 == 1) // when both faces are 1
{num3 = 0;
answer = "n";}
else
num3 += num1 + num2; // sum of two faces
System.out.println (num1 +" "+ num2); // shows both faces
System.out.println (num3); // shows the sum of faces
System.out.println ("Do you want to roll again? (y/n)");
answer = Keyboard.readString();
if (answer.equalsIgnoreCase("n"))
answer = "1";
while (answer.equalsIgnoreCase("1"))
while (num6 <= 20)
num4 = die1.roll();
num5 = die2.roll();
if (num4 == 1 || num5 == 1) // when either face is 1
{num6 = num6;
answer = "2";}
else
if (num4 == 1 && num5 == 1) // when both faces are 1
{num6 = 0;
answer = "2";}
else
num6 += num4 + num5; // sum of two faces
System.out.println (num4 +" "+ num5); // shows both faces
System.out.println (num6); // shows the sum of faces
answer = "y";
Here is my code. It runs okay, but when the dice rolls a 1, it doesn't jump to the next while loop. I need the program to go to the "while loop answer = 1" when the dice rolls a 1 from the "while loop answer = y". If you see my code, I did it by making the answer = "n" to make it jump to the next while loop. I'm sorry if my explanation is confusing. It's my first time asking for help here...
You don't have to fix the code for me, as long as you tell me what I'm doing wrong.
Please help me...Thank you for your help.
Edited by: nakatsu on Nov 12, 2007 7:03 PMHint: all your code does NOT have to be in one method. You have numerous loops some nested inside others. This is starting to get mighty messy and can be tidied up if you think about how you can break some of the code down into smaller chunks and place these into their own methods.
while (answer.equalsIgnoreCase("1"))What other case is there?
Maybe you are looking for
-
Hi, I had my first ever kernel panic just now on my 2006 1,1 Mac Pro and I'm hoping someone can help me identify what may have caused it. I use it for work and it would be pretty disasterous if it failed suddenly. Thanks for looking: Interval Since
-
My problem is this. I have the following 3 packages. layer1.layer2a layer1.layer2a.layer3 layer1.layer2b I have a interface in layer2a that is either public to everyone or private just to that package. I need for layer2b NOT to have access to it but
-
Cant boot os x after installing windows
I have a 2011-2012 macbook pro 15. yesterday I installed windows 7 using bootcamp and installed all drivers. everything seemed fine and I even switched to OS X Yosemite once and went back to windows again. and then I tried to restart and boot back to
-
Can't run Word 2013 in Windows 8
I cannot run word 2013 from windows 8. I can run other office 2013 apps without problem. It gives me the notice: Microsoft Word has stopped working...
-
Cannot UNINSTALL VERSION 11. Please help
Now I'm having a problem uninstalling version 11.1.1.3 on Windows 7. When I start the uninstall EPM, select all the products to uninstall (I want to uninstall EVERYTHING), I get a screen saying "initializing" and then the initialization keeps continu