Need help for interface to process employee expenses

need help for interface to process employee expenses
i have used the interface tables as
AP_INVOICES_INTERFACE
AP_INVOICE_LINES_INTERFACE
are they the right one
is there a concurrent program or any API for doing interface

hi,
i think what ever table are using for interfacing expenses correct.
but you have to enter invoice type as expense report.
Regards,
Srikanth

Similar Messages

Need help for a post-processing "trigger"

Dear all,
Without getting into much detail, I have a system that is simultaneously introducing a sinusoidal Force (F) and measuring the sinusoidal response (X) of a structure under resonance. I need to acquire the whole time signal, including the free decay response in the end (please find attached a sample picture of the time signal and the corresponding data file), so I cannot use a trigger during the measurement. During the stationary response it may be seen that the signal has a slight negative slope: that is due to a phenomenon of dilatation of my structure that is dissipating heat at the same time.
My problem is how to know exactly when my NI-USB 6216 DAQ has stopped the excitation force, which, in my sample waveform would be around 0.025s (I require an automatic process of identifying it).
Is there any VI, filter or trigger function that might provide me that information?
Thank you in advance for your help.
Kind regards,
Diogo Montalvão
Attachments:
R50_18um_controlo_40_60_temp_24_1_12_v0_time_16.txt ‏373 KB

The brute force method:
Can't you use another analog input channel and capture the excitation voltage?
Or if you have a shaker with an amplifier that provide a current monitor output you can capture the excitation current and might find that due to the voltage control some amount of force is still introduced after setting the control voltage to zero and you might have to implement a system model that include the shaker and the output impedance of your amplifier :0
Greetings from Germany
Henrik
LV since v3.1
“ground” is a convenient fantasy
'˙˙˙˙uıɐƃɐ lɐıp puɐ °06 ǝuoɥd ɹnoʎ uɹnʇ ǝsɐǝld 'ʎɹɐuıƃɐɯı sı pǝlɐıp ǝʌɐɥ noʎ ɹǝqɯnu ǝɥʇ'

Need help in optimizing the process

I need help in optimizing my process. Here is what am I doing:
I have two tables table A and table B. table A has list of names and table B has name and ID. Right now I am loading name into cursor from table A and for each name from the cursor I try to match with name in table B to get the ID. This process takes very long to complete. I need help to replace PL/SQL with SQL if possible. I am using oracle utl_match to match the best possible record in table B. table B sometimes returns multiple matching records. I take the top nearest match name and ID for my use (there is not always one to one match)
Any idea or help will be appreciated. Thanks

always provide create table and sample data instert statements when asking a question. also, provide your database version.
because you're using utl_match, you can't really use an index, there must be a cartesian join on the two tables so it may always be slow.
however, here's a sample SQL that you may be able to make use of:
with n as (select 'KATHERINE' person_name from dual
             union all
             select 'STEVE' from dual
             union all
             select 'BRUCE' from dual)
    ,nid as (select 'CATHERINE' person_name, 1 NID FROM DUAL
             union all
             select 'STEFAN', 2 from dual
             UNION ALL
             select 'STEVEN', 2 from dual
             union all
             select 'CATHY',3 from dual)
select n_name, nid
from (
        select n.person_name N_NAME
              ,nid.person_name
              ,nid.nid
              ,ROW_NUMBER() OVER (partition by n.person_name ORDER BY utl_match.jaro_winkler_similarity(n.person_name,nid.person_name) DESC) jws_ORDER
          from n
          join nid on (utl_match.jaro_winkler_similarity(n.person_name,nid.person_name) > 70)
where jws_order = 1;

Need help with interface development

Hi i need help with requirement below with developing interface between or online order system and sap plz lemme know what is bapi i use for creating customer, update and assigining partner id to costumer.
SAP Development
1.     Using standards SAP functional module (with BAPI), create interface that will create/change Ordering party customer in SAP. Following fields are mandatory for customer creation:
     MANDT     Client
     VKORG     Sales organization
     VTWEG     Distribution Channel
     SPART     Division
     KDGRP     Customer Group (= ZORP)
     KUNNR     Customer number
     NAME1     Name 1
     NAME 2     Name 2 (if required)
     SORTL     Search term (short description)
     ZZALTKN     Search term 2 (old customer number)
     LAND1     Country
     ORT01     City
     PSTLZ      Zip Code
     REGIO      Region (state in USA)
     STRAS     Street
     TELF1     Primary telephone number
     TELFX     Primary Fax number
     ZZPRPLANS     Payment Plan
     CCINS     Payment card: Card type
     CCNUM     Payment cards: Card number
     CCDEF     Payment Card: Default Card Indicator
     ZBDGID     Customer Budget ID
     ZHOLD     Budget Hold indicator
     ZZCOSTCENT     Cost Center
2.     Upon successful customer creation system will issues S (success) message that customer has been created.
3.     New ordering party customer created in step ½, will have to be assigned as new partner to its belonging Sold-to/Ship-to customer. Use standard SAP customer functional module in order to perform this partner ID assignment. Partner ID for ordering party should be ZO.
1.7     Enhancement Functionality
Apart from creating a new interface to do the required functionality, the Order Create Interface also has to be changed to accommodate a field to pass the Ordering Party Number on the Order. The technicalities of how we are going to implement the interface will be laid out in the Tech Specs.
Thanks
in advance

You have double posted, please mark this one as "solved on my own" and refer to this thread
need help with interface development
Regards,
Rich Heilman

Need help for publishing web intelligence document (universe) into InfoView

Post Author: mirage
CA Forum: Publishing
Hello all,
I need help for publishing web intelligence document (universe) into InfoView.
can't find this information in Business Objects Designer's Guide and in Business Objects Administrator Guide.
Can somebody give short instructions how can I do it?
Regards, Slava

If the change between the 2 types of data has to happen dynamically during run time them
1. Use 2 dataproviders
a. Current
b. Historic
2. Merge the 2 dimensions
3. Use Webi variable to switch between the measure of the current and historic universe
Ex if [year] < 2010 then historic.[expense] else current.[expense]
Hope this helps,
Divya

Need help for access list problem

Cisco 2901 ISR
I need help for my configuration.... although it is working fine but it is not secured cause everybody can access the internet
I want to deny this IP range and permit only TMG server to have internet connection. My DHCP server is the 4500 switch.
Anybody can help?
         DENY       10.25.0.1 – 10.25.0.255
                          10.25.1.1 – 10.25.1.255
Permit only 1 host for Internet
                10.25.7.136 255.255.255.192 ------ TMG Server
Using access-list.
( Current configuration )
object-group network IP
description Block_IP
range 10.25.0.2 10.25.0.255
range 10.25.1.2 10.25.1.255
interface GigabitEthernet0/0
ip address 192.168.2.3 255.255.255.0
ip nat inside
ip virtual-reassembly in max-fragments 64 max-reassemblies 256
duplex auto
speed auto
interface GigabitEthernet0/1
description ### ADSL WAN Interface ###
no ip address
pppoe enable group global
pppoe-client dial-pool-number 1
interface ATM0/0/0
no ip address
no atm ilmi-keepalive
interface Dialer1
description ### ADSL WAN Dialer ###
ip address negotiated
ip mtu 1492
ip nat outside
no ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication pap callin
ppp pap sent-username xxxxxxx password 7 xxxxxxxxx
ip nat inside source list 101 interface Dialer1 overload
ip route 0.0.0.0 0.0.0.0 Dialer1
ip route 10.25.0.0 255.255.0.0 192.168.2.1
access-list 101 permit ip 10.25.0.0 0.0.255.255 any
access-list 105 deny   ip object-group IP any
From the 4500 Catalyst switch
( Current Configuration )
interface GigabitEthernet0/48
no switchport
ip address 192.168.2.1 255.255.255.0 interface GigabitEthernet2/42
ip route 0.0.0.0 0.0.0.0 192.168.2.3

Hello,
Host will can't get internet connection
I remove this configuration......         access-list 101 permit ip 10.25.0.0 0.0.255.255 any
and change the configuration ....      ip access-list extended 101
                                                            5 permit ip host 10.25.7.136 any
In this case I will allow only host 10.25.7.136 but it isn't work.
No internet connection from the TMG Server.

Need help for Transfer PO

need help for Transfer PO.
i need help for to transfer PO from one season to onther season. pleas ehelp me how to proceed and how 2 approach the process.
if any code is there please provide me

follow the link
it may help you
MM SCENARIO
https://www.sdn.sap.com/irj/sdn/advancedsearch?cat=sdn_all&query=abapcodetotransferpurchaseorder&adv=true&sdn_author_name=&sdn_allusernamesofthread=&sdn_category=&sdn_forum=&sdn_updated_on_comparator=GE&sdn_updated_on=&sortby=cm_rnd_rankvalue
reward if helpful
Edited by: sharad narayan on Apr 8, 2008 3:16 PM

I have problem with buying in games , I got the massage that the purchased can not be completed , please contact iTunes support.. I need help for my case please

I have problem with buying in games , I got the massage that the purchased can not be completed , please contact iTunes support.. I need help for my case please

http://www.apple.com/support/itunes/contact/

Need help for Format HD

Hi I need Help for Formating HD so Wat Key need hold on start up for format HD I apprciated you Help

Jesus:
Formatting, Partitioning Erasing a Hard Disk Drive
Warning! This procedure will destroy all data on your Hard Disk Drive. Be sure you have an up-to-date, tested backup of at least your Users folder and any third party applications you do not want to re-install before attempting this procedure.
• With computer shut down insert install disk in optical drive.
• Hit Power button and immediately after chime hold down the "C" key.
• Select language
• Go to the Utilities menu (Tiger) Installer menu (Panther & earlier) and launch Disk Utility.
• Select your HDD (manufacturer ID) in left side bar.
• Select Partition tab in main panel. (You are about to create a single partition volume.)
• _Where available_ +Click on Options button+
+• Select Apple Partition Map (PPC Macs) or GUID Partition Table (Intel Macs)+
+• Click OK+
• Select number of partitions in pull-down menu above Volume diagram.
(Note 1: One partition is normally preferable for an internal HDD.)
• Type in name in Name field (usually Macintosh HD)
• Select Volume Format as Mac OS Extended (Journaled)
• Click Partition button at bottom of panel.
• Select Erase tab
• Select the sub-volume (indented) under Manufacturer ID (usually Macintosh HD).
• Check to be sure your Volume Name and Volume Format are correct.
• Click Erase button
• Quit Disk Utility.
cornelius

Need help for my requirement...

Need help for my requirement...
Hello Experts,
I have report where users can input the company, housebank, account ID and posting date.
Now in one column of my report named 'Cash in Bank', I need to get all postings from cash
accounts with GL code ending in '0'. Now, I know that I can get the amounts in BSIS/BSAS
but how do I link it with the proper bank and account?
For example:
                   Cash in Bank
Bank A
Account ID 1     1,000,000
Account ID 2     25,000,000
Hope you can help me guys. Thank you and take care!

hi Viraylab,
each house bank you can find in table T012, in T012K you'll find the bank accounts to the housebank, the G/L account will be in T012K-HKONT.
hope this helps
ec

Need help for flash builder

i need help for flash builder 4 and papervison 3d. I need to create a slider with it ranges of value from 10 to 50 to adjust the camera values for the camera.fov and also need to create it for the yaw of the object from 0 to 360. I try to look for any slider event and classes in this program but cant find any, btw, i need to use the AS only project file.
here is my codes:
can you please tell me how i should modify the codes?
package
    import flash.display.BitmapData;
    import flash.display.Sprite;
    import flash.events.Event;
    import org.papervision3d.materials.BitmapFileMaterial;
    import org.papervision3d.materials.BitmapMaterial;
    import org.papervision3d.objects.primitives.Sphere;
    import org.papervision3d.view.BasicView;
    [SWF (width="800", height="600", backgroundColor="0x000000",frameRate="30")]
    public class EarthBitmap extends BasicView
        private var sphere:Sphere;
        public function EarthBitmap()
            super(800 , 600);
            var earthmaterial:BitmapFileMaterial = new BitmapFileMaterial("../assets/Earth.jpg");
            sphere = new Sphere(earthmaterial,100,20,18);
            camera.fov = 25;
            scene.addChild(sphere);
            addEventListener(Event.ENTER_FRAME,rotateSphere);
        public function rotateSphere(evt:Event):void
            sphere.yaw(0.2);
            singleRender();

Turn the click handler into a full on separate function. Then store all the views in an array and use Math.rand() to randomly choose one.
Something like this:
<fx:Script>
     <![CDATA[
          var questionsArray:Array = {question2,question3,question5,questionRed,questionGeography};
          function buttonClickHandler(event:MouseEvent){
               var randomProblem:int = Math.floor(Math.random()*(questionsArray.length));     //generates a random integer between 0 and the total number of questions in the array (arrays are 0-based)
               navigator.pushView(questionsArray[randomProblem]);
     ]]>
</fx:Script>
<s:Button id="randomProblemButton" label="Next Problem" click="buttonClickHandler(event)" />
Haven't tested that, but something along that line should work

Need help for importing oracle 10G dump into 9i database

hi, Someone help me to import oracle 10G dump into 9i database. I'm studying oracle . Im using oracle 10G developer suite(downloaded from oracle) and oracle 9i database. I saw some threads tat we can't import the higher version dumps into lower version database. But i'm badly need help for importing the dump...
or
someone please tell me the site to download oracle 9i Developer suite as i can't find it in oracle site...

I didnt testet it to import a dump out of a 10g instance into a 9i instance if this export has been done using a 10g environment.
But it is possible to perform an export with a 9i environment against a 10g instance.
I am just testing this with a 9.2.0.8 environment against a 10.2.0.4.0 instance and is working so far.
The system raises an EXP-00008 / ORA-37002 error after exporting the data segments (exporting post-schema procedural objects and actions).
I am not sure if it is possible to perform an import to a 9i instance with this dump but maybe worth to give it a try.
It should potentially be possible to export at least 9i compatible objects/segments with this approach.
However, I have my doubts if this stunt is supported by oracle ...
Message was edited by:
user434854

Need Help for Nokia 6500 slide

Hi all I'm A new Guy here ,
But I do really need help for hard reset my phone
I already try *#7073# But It doesn't work ,
If Anybody know to make a hard reset please help

rwss wrote:
I'v got te same problem with my 6500 Slide, is there a button combination that we have to press
to hard reset the 6500 Slide?!
How does the 6500 slide hard reset?
That's simple.
All you have to do is:
From MENU goto SETTINGS, When there scroll down and select 'Restore Factory Setting'.
There are two options in there:
"Restore Settings only"
and
"Restore all"
Select "Restore All"
When done the phone will delete every thing on the Phone memory(C:\)(contacts,picture,messages etc)
and also restore phone to its original settings and will restart.
This proceedure is mostly common on S40 phone.
Hope this explain and solve the problem.

Need help for cenvat reversal

Hi Friends,
Need help for cenvat reversal.
Reversed MIRO by MR8M & MIGO by 102 movement but not able to post & cancel cenvat by J1IEX.
In table J_1IEXCHDR status = "P" and J1I5 does not update for document of 102 movement because reversal document of MIGO, i.e. material document with 102 movement type does not have excise tab. MBSM-Cancelled Material Documents, does not show any of the material documents.
Want to reverse the cenvat credit, please help.
--Anil Bhamere

Hi,
If I select Cancellation in MIGO then there is only Material Document option.
In MIGO Purchase Order option shows for Goods Receipt, Goods Issue and Subsequet Adj.
In this case I have been selected Goods Receipt option followed by purchase order number by which original goods receipt MIGO was created, selected 102 movement type and from line item respective MIGO document. The reversal document created successfully where as original MIGO document does not show in cancelled document list. When post option selected from J1IEX and entered vendor excise number then message appeared as No Part I exists for availing credit in excise invoice xxxxx.
If Cancel option selected from J1IEX and entered vendor excise number then message appeared as Excise invoice xxxx has already been posted for vendor xxxxx.
Please help.
Regards,
Anil Bhamere

Need help for finding objects impacted by size change for an infoobject

hi all,
need help for finding objects impacted by size change
for xxx infoobject, due to some requirements, the size to be changed from
char(4) to char(10), in the source database tables as well as adjustment
to be done in BI side.
this infoobject xxx is nav attribute of YYY as well as for WWW
infoobjects. and xxx is loaded from infopkg for www infoobject load.
now that i have to prepare an impact analysis doc for BI side.
pls help me with what all could be impacted and what to be done as a
solution to implement the size change.
FYI:
where used list for xxx infoobject - relveals these object types :
infocubes,
infosources,
tranfer rules,
DSO.
attribute of characteristic,
nav attribute,
ref infoobject,
in queries,
in variables

Hi Swetha,
You will have to manually make the table adjustments in all the systems using SE14 trans since the changes done using SE14 cannot be collected in any TR.
How to adjust tables :
Enter the table name in SE14. For ex for any Z master data(Say ZABCD), master data table name would be /BIC/PZABCD, text table would be /BIC/TZABCD. Similarly any DSO(say ZXYZ) table name would be /BIC/AZXYZ00 etc.
Just enter the table name in SE14 trans --> Edit --> Select the radio button "Save Data" --> Click on Activate & adjust database table.
NOTE : Be very careful in using SE14 trans since there is possibility that the backend table could be deleted.
How to collect the changes in TR:
You can collect only the changes made to the IO --> When you activate, it will ask you for the TR --> Enter the correct package name & create a new TR. If it doesn't prompt you for TR, just goto Extras --> Write transport request from the IO properties Menu screen. Once these IO changes are moved successfully, then the above proceduce can be followed using SE14 trans.
Hope it helps!
Regards,
Pavan

Need help for interface to process employee expenses

Similar Messages

Maybe you are looking for