Need Help for msi kt4 ultra (6590)

Mine Windows XP is not compatible with the promise serial ata driver ;(
The system is much unstable one
I cannot use the controller serial ata
What I can make??
Thanks
Fede

During installation XP it says to me that the driver they have not exceeded the compatibility test.
Windows advises me not to continue.
But I can make to work the raid with a single disc ATA
Thanks
Fede

Similar Messages

Which CPU for MSI KT4 ULTRA?

Hello,
I would like to change my actual CPU which is Athlon XP1500 by a better one.
Can you tell me which maximum frequency can I put with this mothercard?
Thanks for your reply
Giro
WIN 2000 Pro SP4
MSI KT4 ULTRA
512Mo DDR-SDRAM

anything for AMD up to Althon XP 3000 (333FSB or below only)

Urgent help with MSI KT4 Ultra

hey,
off my folks yesterday i got...
MSI KT4 Ultra
512mb DDR333 PC2700
Athlon XP 2600+
Maxtor DiamondMax9 40gb HDD...
i thought i had it all setup right with the HDD in IDE1, DVD and CD-RW in IDE2 and floppy in the floppy bit...
at 1st the CPU cwas only clocking at 1250mhz, but then came here and sorted that prob..... (Sperad spectrum then adjusted the FSB to 166mhz ) then after that, when i go to boot up i got.... "no device connected to the Fasttrack controller...bios not installed" then browing through the forum i found how to "solve" that problem... ( disabled the Serial ATA thing, dont know if thats right .... ) but now i dont get that "bios not installed" line any more.... all i get is a flashing line in the top left of my screen....
so to sum up....all i get now is.... that flashing line......what could be goin wrong?
Thanks in advance.....a very distressed...
//Simpo

This is an AMD board, so I will move your post to that forum.

PCI Deviders for a KT4 Ultra (6590)

Does any one know what pci deviders work at all the different fsb.
Ive emailed msi but they wont reply.
Can any 1 help me???

Hi,
FSB 100~120 MHz, divider= 1/3
FSB 121~151 MHz, divider= 1/4
FSB above 152 MHz, divider= 1/5
and, no divider 1/6 support on the chipset.

MSI KT4 Ultra 6590 destroyed "L19"

Hi!
While trying to change the cooling system I pushe my srew driver too much in so I destroyed the Spool (??) L18 near the CPU which is (At least in my opinion) important for the AGP, which means that the Computer boots normally but without image on the screen!
The Question is: how can I change the spool?
Where can I get one to replace it??
which Induction Capacity does it have to have?
mike

Hi,
The answers to your questions I got from MSI for L18:
it can only be done if he has knowledge or experience in soldering
normally, the spare parts can be bought on hardware parts store selling capacitors/resistors etc.
L18,inductor,10n/5%,0603,400mA,RDC=0.26 ohm

Windows XP and MSI KT4 ULTRA 6590-FISR

Has anyone figured out how to do a clean install of Win XP with this board?
I keep getting a "Device Not Certified error", at which point I elect to IGNORE the error and continue. There is absolutely NO INDICATION of what the problem device is.
However, at exactly 34 minutes left "Installing Windows", the installation routine locks up and I can't go any further.

The 2nd day into this,(I am on day 5) I took out my RAM and replaced it from another machine...same problem.
I then took out my PS and replaced it from another machine...same problem.
Diagnosing/testing all RAM and the PS showed no problems.
I then went through the BIOS and performed a multitude of enabling/disabling system settings. By disabling the following INTEGRATED PERIPHERALS/OnBoard PCI Controller Item:
LAN Controller
I was able to get Windows XP to load.
However, I cannot get XP to boot...not in NORMAL, or SAFE or SAFE with NETWORK, SAFE with PROMPT. But I am making progress.

KT4 Ultra (6590) need update of the Promise SATA RAID Controller PDC20376

The last Bios update AMI 1.4 for the KT4 Ultra (6590) have built in the bios version 1.00.0.18 for the PDC20376 (Promise 376).
I can configure 2 maxtor (6E040T0) sata1 in a raid0 array and it works under WinXP SP3,
but the 2 drives are working in UDMA5 according to the FastBuild Utility when the motherboard specifications talks about 150Mb (SATA1).
It's not an OS problem because the FastBuild Utility at Bios startup show the UDMA5 mode for HDD.
It's not a Maxtor 6E040T0 (SATA1) problem because have no jumper to set.
The Promise support center don't provide support for built in raid controller but the responce was that it's related to a known bios issue of the controller, so i have to update.
For the last Bios version for the S150 TX4 controller look at:
http://promise.com/support/download/download2_eng.asp?productId=108&category=all&os=100&go=GO
It's impossible to update the bios with the promise tool because the controller is integrated in the motherboard.
I read for example than on the motherboard K7N2 Delta-ILSR the bios version of the Promise 376 controller is 1.00.0.21:
https://forum-en.msi.com/index.php?topic=92756.msg665966#msg665966
I think the only solution is a modding bios, where i have to replace only the Promise controller bios but:
1) The tool amibcp.exe can't open the A6590VMS.140 AMI bios (renamed .rom), i don't know why!!!
2) What promise controller bios rom file is good?
Can anyone out there help . . . please ?

This is my results compared to my other UDMA6 HDD on IDE1, HDTach long bench stop with "Read Error" and only quick bench works.
The version of the Controller driver under WinXP-SP3 is 1.0.1.29 and I configured the driver in the PAM Utility with:
"Driver Write Cache" enabled and "Write Back" as cache settings (The 2 Maxtor SATA1 in RAID have 2MB of cache, but i don't know How many cache have the controller!!).
The Burst Speed is too strange!!! quick bench error?
I made it so your image is clickable.
-Frankenputer

PROBLEMS AGAIN, MSI KT4 ULTRA GIVE POOR STABILITY IN MY SYSTEM!!!

Hi, i get problems when overclock (fsb) my cpu with 133 fsb to 136 ONLY!!! , only support the overclock my cpu 1800(1533mhz)--to(1580mhz), high fsb 137 or high freeze , restart my system when run games or aplication with geforce 3 ddr 64mb, i modify vol agp to 1.8 , but get error again.
HELP ME!!!
I NEED NEW BIOS THAT STABILIZE MY SYSTEM!!!
System:
MSI KT4-ULTRA 6590-SR
CPU XP 1800+
256 DDR SANSUMG
T.VIDEO GEFORCE 3 DDR 64 detonator 41.09 agp4x
WINDOWS XP PRO SPK1
POWER 350 WATTS CODEGEN

Thanks for you help, but my power 350 watts codegen work a:
20A---3.3v
30a---5v
However i read guide revision 12-12-02 about psu and all configuration is correct !!!!!!
My powersupply not is problem
I NEED THAT MSI MAKE NEW BIOS FOR KT4-ULTRA!!
Thanks

KT4 ultra (6590) and Randeon 8500 instability

This is my pc:
Msi Kt4 Ultra (6590)
Athlon Xp 2000+
512 mb ddr pc 2700
Ati Radeon 8500 Ret.
maxtor diamondplus 8 80gb
Pioneer DVD 16x slot-in
Asus ISDN Adapter internal
Skystar 2 DVB sat Adapter
Power Supply Deer 350 W (amd certificaded)---- 5v/35A
3,3/24A
Monitor 19" Philps 109B.
S.O WinXP PRO SP1.
My systems runs great but when i play games sometimes my system crash and (very curios) before about 3-5 min of game play i see small interferences like small white orizzontal jolt similar the interference when a cellular phone ring near the monitor. the problem it persists with any resolution and any monitor refresh rate !!!!!
What i've tested:
I have the lasted KT4 ultra bios, test any Randeon Drivers (include the lasted 779 beta drivers) and lasted via's drivers
Near my monitor there isn't any interference source !!
Monitor is perfect (tested in other system )
it's not Radeon8500 problem because i play games perfectly in other system (a7v266 and same hardware)
KT4 are not damaged because i play game perfectly with another video card (geforce2 Mx400)
It's not a PSU problem because i replaced AMD athlon 2000 + with AMD Athlon 900 (the rest hardware is the same) and the problem it persists.
although i have 5 years experience under PC assemblage , I do not know that what to make!!!
is There an incompatibility with Radeon8500 and KT4 Ultra ??
Please someone can help me ??? ;( ;(

It might be the AGP driving value problem. Set it to EA in BIOS. It works for most people with components like yours. If that does not help, switch to AGP 2x and see if the problem went away. If it did, look for other DGP Driving values and turn off some AGP related features (sideband, fastwrite etc)
If that did not help,
See this post and try to draw come conclusions. Sometimes the Power Supply is at fault not because of being underpowered (which you checked with Athlon 900) but because of the incorrectunstable voltages and other similar crap. With 266Mhz fsb and 333Mhz memory interface the boards now are too sensitive to cheep power supplies.
Good Luck
KT3 Ultra2
Athlon 1800+
PowerColor Radeon8500 128mb
No-name 512 memory
No-name 400W power supply

MSI KT4 Ultra-SR (MS-6590) And IDE3

Rig is As Follows:
MSI KT4 Ultra-SR (MS-6590)
AMD Athlon 1000Mhz :(
512MB DDR333 (PC2700) x1 stick
MSI GeoForce 4 Ti4200 8)
IDE1: Western Digital 40Gb 5400rpm (win xp pr) as master & Maxtor 80Gb 7200rpm as slave
IDE2: Liteon 52x24x52 CD-RW ) as master & Samsung 12x DVD as slave.
Soundblaster 5.1 Live PCI
350w Power Supply
MSI D-Bracket 2 & S-Breackets Fitted Also.
I have Three Questions.
>My CPU has a FSB of 200, but the bios (version that came with board) shows it as 100 FSB. See here for athlon bus speeds
Is it ok to increase the bus speed without damaging the processor.
>The two brackets that i have fitted (s and d brackets) do not work. Why?
>What are the optimal and settings for my ram (PC2700 512MB DDR) and GFX Card (MSI GF4 TI4200).
>Oh yeah, my CPU is now operating at a higher temp than before (using old K7VZA ECS Mobo) @ 50-55. Is this normal??
Sorry for the n00b questions, it's just that this is the first time iv ever taken my PC to pieces and re-configured it myself :P
Thanks in advance. -RjA

I can help a little 1000MHZ AMD chip=200FSB XP CPUs=266FSB this is CPU speed . AMD 1000MHZ CPU needs to run @100FSB where a XP CPU can run @133FSB This is MEMORY speed . Trying to crank that poor old chip up to anything other than 100 will do you NO good. You need to buy a bigger cpu of the XP kind. A lot of the older XPs can be had for a low price. 50c isn't not super hot. My KT4 runs in the 40s. You might want to think about a bigger cpu cooler to bring the temps down a bit. Most of your settings should be left at system default, since you only have a 1000MHZ CPU. When you go up to an XP then you can make a few changes. Regards BIGDADDY51 :D :D

HELP! HELP! HELP! KT4 Ultra (6590)

Hi People,
About a month ago I bought a new system... Here are the specs....
- AthlonXP 1800+
- MSI KT4 Ultra (MS-6590)
- 512 Mb DDR PC2700 (Spetek)
- MSI GeForce4 MX440 AGP
- Maxtor DiamondMax 9 60Gb IDE
- LG CD-RW 52x24x52 IDE
- Generic 60x CD-Rom IDE
- 320w Power Supply (AMD Certified)
I have the following problem... RANDOM BOOTS! :( I dunno what is the problem... But I have some questions to MSI and for you... My KT4 hasn´t a cooler chipset on northbrigde, is it normal? Cause my system temperature is between 46ºC (idle) and 48ºC (full)... and my CPU is 47ºC (idle) and 52ºC (full)... HELP! HELP! HELP! What should I do? Ah, BIOS version is 1.2...
Best regards,
Bruno.

Your PC setup is pretty similar to mine. I had similar reboots as well and suspected the KT4 Ultra. It turned out to be a dodgy stick of RAM. Try the ramtesters from http://www.simmtester.com and http://www.memtest86.com, they'll definately find any RAM problems. Other than that disable the auto reboot on crash and see what the message on the Blue Screen tells you.
For info, since my rebuild with a new stick of ram I'm running...
4in1 v4.45
Latest MSI drivers from MSI Update v2 (except the beta graffics driver)
Bios 1.3 (though 1.2 seemed ok to me)
XP SP1 with all updates from MS.
Hope this helps...
YT

MSI KT4 ULTRA MS-6590

I have this motherboard: MSI KT4 ULTRA MS-6590 sempron and I have already bought the new CPU SEMPRON (AMD Sempron 2400+). I want to know if my motherboard is compatible with new CPU.
Thank you
Sorry for my English, but I'm Italian.

Hi
Not according to http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support_detail.php?UID=356&kind=1

Problem with my MSI KT4 Ultra

Hi all!
I have a BIG problem, I have tried to look at this board, but there is many different answers out there ;(
I have KT4 Ultra with Athlon XP 2600+
I have set FSB to 166, and when I startup BIOS says Athlon XP 2600+.
But in windows system, it only says:
AMD Athlon XP2600+
2.09Ghz !!!!
768Mb RAM
Why is windows only says 2.09Ghz??
AND, I think my system is very slow. I used to have AMD 1200Mhz. And this sytem is almost like my last computer.
My System:
MSI KT4 Ultra ( MS-6590 ) with BIOS
CPU AMD Athlon XP 2600+
768MB DDR 400 RAM
GeForce 4 TI4200AGP 8x
80 Gb Seagate 7200 Harddrive

Quote
Originally posted by swedecom
Ok, I use these settings in my BIOS, are they right for my system??
MY SYSTEM:
MSI KT4 Ultra ( MS-6590 ) with BIOS
CPU AMD Athlon XP 2600+
768MB DDR 400 RAM
GeForce 4 TI4200AGP 8x
80 Gb Seagate 7200 Harddrive
MY SETTINGS IN BOIS:
Spread Spectrum = +- 0.25%
CPU FSB Clock = 166Mhz
CPU Ratio = Auto
CPU Vcore = (V) Auto
DDR Voltage (V) = Auto
Termination Vol (V) = Auto
AGP Voltage (V) = Auto
Hope someone can help me out

MSI KT4 Ultra and AMD XP3200+

Hi,
Is it possible to run an AMD Athlon XP 3200+ on the MSI KT4 Ultra Motherboard?
I know the motherboard supports FSB200/266/333, but will the cpu work if I manually set it to FSB400 in the bios?
Thanks for you help.

I don't think the cpu is unlocked, it is an original 3200+.
I thought you need an unlocked cpu if you want to overclock the cpu.
I just want to leave the multiplier on auto and set the frequency to 200MHz (its original setting).
The reason I need to know is that I stupidly bought the cpu without checking my motherboard FSB support and I cant return the cpu.
I have not received it yet and wanted to know if it was possible to get my computer up and running even if the KT4 Ultra does not officially support FSB400.
Would there be any harm in trying the cpu in my motherboard.
If anyone has managed to run an AMD XP3200+ cpu on a MSI KT4 Ultra, please let me know.
Thank You.

PROBLEM MSI KT400 ULTRA (6590) WITH LEADTEK WINFAST TV 2000 DON'

?( ?( ?( ?( ?( ?( ?(
MY PC
MSI KT400 ULTRA (6590)
ATHLON 2000 XP
256 DDR 333
128 DDR ATI RADEON 9000
WINFAST TV 2000 (LEADTEK) (don't work IN MODE OVERLAY)
2 HDD 40 GB - DVD ROM - FLOPPY ...
MODE OVERLAY DON'T WORK NEED HELPPPPPPPPPPP
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
msn [email protected] please need help
msn [email protected] please need help
msn [email protected] please need help
msn [email protected] please need help
msn [email protected] please need help

Quote from: Stu on 14-January-08, 01:30:33
Driver:
http://www.dynamode.co.uk/support/drivers/wireless/wl-xi-700xa/wl-xi-700xa-Win-WLANUSB&PCMCIA.zip
Thanks for all your help.
I tried that driver already...same result, but no matter.
I got this sorted today...went and bought 20 mts of ethernet cable, works a treat.
I've come to the conclusion that the USB WiFi Dongle is Kaput.
It looked like it worked in my laptop but this is already WiFi so I guess the new software was just using
the existing connection.
Dongle was never recognised in the desktop PC I wanted to use it in and in my other desktop was recognised as
Wireless USB Device but after trying to install it got to the same scenario where Windows could never find better drivers.
Just hope Ebuyer will take it back or the £8.50 it cost might bankrupt me!
Cheers

Need Help for msi kt4 ultra (6590)

Similar Messages

Maybe you are looking for