Need help getting open nat type on home hub 3 for ...

just got the homehub 3 and tried to play black ops but cannot connect because of moderate nat type. i forwarded the ports on my old hub 2, but cannot find anywhere to help me do it on 3.can anyone help?

Hi Robert-Allison,
Thanks for posting. Take a look here for some information on Hub 3 nat issues. Let us knoe if that helps.
Cheers
David
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)

Similar Messages

Need help getting new printer hp deskjet 3520 setup for eprint and wireless

need help getting new printer hp deskjet 23520 stup for eprint and wireless

Hi Pastorlee7,
I see that you're having problems setting up your printer. I would take a look at the document below.
Hp deskjet 3520
Let me know how it goes.

Should I get a new router to get open NAT type?

Whenever I play COD Black ops 2 on my xbox 360 my NAT type is strict. I have a centurylink 660 series modem and that is working to its full potential of the bundle we bought from them. I also have an airport extreme (2009). I Know theres all these port forwarding stuff, but whenever I try to do that, my whole network crashes and I have to factory default all of my stuff. So would getting a new router help me? also, I have my airport extreme in bridge mode because It said I have a double NAT and DCHP. So what would be the best solution for getting an open NAT type for Call of Duty on Xbox 360? I also have a MacBook pro (2009).

Yes, that is what I am doing. I don't know the setup details for what you want to do, but I am running a MacBook Pro (late 2008), iPad, and a couple of iPhones on wifi through my Airport Extreme base station. I also run backups to a Time Capsule.
The base station is set up to "Create a wireless network" and runs in "DHCP and NAT" mode. The Time Capsule and two Airport Expresses are set up to "Join a wireless network". My cable modem (Ubee DVW3201b) runs in bridge mode, connected by cable to the WAN port on the base station. I have the wifi capability of the modem disabled. It took me some trial and error to get the cable modem set up properly, but there is a lot of information out on the net.

Cant get open nat type for PS3, it use to be but wont go back

im on Fios with the verizon router. I had the DMZ set to an ip with the PS3 also on it. the nat type was open and all was ok. I dont know how long its been this way (guessing not long because I have sucked at COD this week!) but I noticed im not at moderate. I checked the DMZ and the ip was still there. looked at PS3 and it was empty for some reason, so I put the ip back. ive restarted and tried other IPs andit will not go back to open. ive looked at youtube tutorials to be sure that im not missing anything but the vids seem tobe older because I have more options on the router settings than what the vids show, guess I have newer firmware. Any suggestions?

actually, Open is what you want. you have a lot better preformance online when dealing with fast paced games like COD. you will really notice a difference. generally you just designate an IP in the DMZ settings of the router, then tell the PS3 to only use that IP, and thats it. just seems now on my end thats no longer the case and cant get it to go

Trying to get Open NAT Type on 2 Xbox 360's at the same time

After buying 3 new routers in a row trying to find a compatible router at my last house with Comcast, I finally found one that works then move to a house with Fios. I LOVE the speed... but this modem/router took our nat issue back to square one... obviously we're trying to play CoD: MW3 together, but we're both getting moderate NAT. I read a couple posts on the forums here and nobody could offer up a solution (looks like it has something to do with a NAT table that's too small or something?)
Anyway, I came up with a potential solution but it's something I've never done before, maybe someone else knows how:
I'm trying to connect my old dlink router to the actiontec router's internet connection, then have the xbox's connected to the dlink router with dhcp enabled. my theory is to make the actiontec router accept whatever traffic is coming through the dlink router, without knowing what devices are connected to the dlink router.
in this way the dlink router could potentially control the NAT between the xbox's via UPnP by itself, and the actiontec router would have the xbox live ports forwarded to the dlink router's ip address.
Am I crazy, could this work? so far I have the dlink router on a seperate subnet (192.168.0.1) while the actiontec is 192.168.1.1. the dlink router can ping machines on the actiontec router's network but not vice versa. also the dlink router cannot access the internet through the actiontec router yet. which is why i'm here. if this could work, can anyone explain how to set it up?

TallgeeseIV wrote:
After buying 3 new routers in a row trying to find a compatible router at my last house with Comcast, I finally found one that works then move to a house with Fios. I LOVE the speed... but this modem/router took our nat issue back to square one... obviously we're trying to play CoD: MW3 together, but we're both getting moderate NAT. I read a couple posts on the forums here and nobody could offer up a solution (looks like it has something to do with a NAT table that's too small or something?)
Anyway, I came up with a potential solution but it's something I've never done before, maybe someone else knows how:
I'm trying to connect my old dlink router to the actiontec router's internet connection, then have the xbox's connected to the dlink router with dhcp enabled. my theory is to make the actiontec router accept whatever traffic is coming through the dlink router, without knowing what devices are connected to the dlink router.
in this way the dlink router could potentially control the NAT between the xbox's via UPnP by itself, and the actiontec router would have the xbox live ports forwarded to the dlink router's ip address.
Am I crazy, could this work? so far I have the dlink router on a seperate subnet (192.168.0.1) while the actiontec is 192.168.1.1. the dlink router can ping machines on the actiontec router's network but not vice versa. also the dlink router cannot access the internet through the actiontec router yet. which is why i'm here. if this could work, can anyone explain how to set it up?
to get both working, you must enable uPNP on your router. If you are connecting your xboxes to your Actiontec, same rule applies. There is no way to allow two xbox's to connect with OpenNAT without uPNP.
Your best bet (if you can't move the actiontek behind your D-LINK) is to hook the two xbox's up to the Actiontec (preferable wired, but wifi should work).
I have 2 xbox's running fine with uPNP enabled. Both have OpenNAT.

Need help getting my NAT open on a WRT54G

Ok I have a WRT54G. I have 2 Xbox 360s both with Xbox Live. One is in a room with a wired connection the other is in a room that doesn't have any lines going to it so it has to be wireless. I am not gonna chip out $100 for the xbox wireless adapter, so I connected the xbox to my laptop and did internet sharing. It works fine, but the NAT is moderate rather than open. In the other room with the wired connection it is open. With the NAT being moderate it makes it nearly impossible to join any games. So what should I do? Also I have a Powerbook G4 laptop running Mac OS X 10.4.11

Well try to change the positions of two xboxes. If still xbox connected to laptop has moderate NAT, then may be Internet sharing is not properly done.
If "xbox currently having moderate NAT" is still moderate even with the ethernet cable connection direct to router, then settings on xbox needs to be verified.

Need help getting simple Nat config to work

I can't seem to get the below Nat config to work. I removed the crypto from the fa0/0 for testing.
Why can't i get xlates when I ping 192.168.1.5 or 192.168.1.1? As you can see my access list isnt getting touched?
What am i missing?????
==============================================
CCC#sh access-lists
Standard IP access list 1
10 permit 10.10.10.0, wildcard bits 0.0.0.255
==============================================
CCC#sh ip nat t
CCC#
==============================================
CCC#sh ip nat s
Total active translations: 0 (0 static, 0 dynamic; 0 extended)
Outside interfaces:
FastEthernet0/0
Inside interfaces:
FastEthernet0/1
Hits: 0 Misses: 0
CEF Translated packets: 0, CEF Punted packets: 0
Expired translations: 0
Dynamic mappings:
-- Outside Destination
[Id: 2] access-list 1 interface FastEthernet0/0 refcount 0
[0] prot 6: port #7 refcount 1 syscount 1 localport 4294967295, localaddr 0.0.0.
0, flags 1
[0] prot 6: port #9 refcount 1 syscount 1 localport 4294967295, localaddr 0.0.0.
0, flags 1
[0] prot 6: port #11 refcount 1 syscount 1 localport 4294967295, localaddr 0.0.0
.0, flags 1
[0] prot 6: port #13 refcount 1 syscount 1 localport 4294967295, localaddr 0.0.0
.0, flags 1
[0] prot 6: port #19 refcount 1 syscount 1 localport 4294967295, localaddr 0.0.0
.0, flags 1
[0] prot 6: port #21 refcount 1 syscount 1 localport 4294967295, localaddr 0.0.0
.0, flags 1
=============================================================================
CCC#sh run
Building configuration...
Current configuration : 1490 bytes
version 12.4
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
hostname CCC
boot-start-marker
boot system flash c2600-adventerprisek9-mz.124-25d.bin
boot-end-marker
no aaa new-model
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
archive
log config
hidekeys
crypto isakmp policy 2
encr 3des
hash md5
authentication pre-share
group 2
lifetime 400
crypto isakmp key cisco123 address 1.1.1.3
crypto ipsec transform-set Petaluma_VPN ah-sha-hmac esp-3des
crypto map Petaluma_1 1 ipsec-isakmp
! Incomplete
set peer 1.1.1.3
set transform-set Petaluma_VPN
match address 100
interface FastEthernet0/0
ip address 1.1.1.2 255.255.255.0
ip nat outside
ip virtual-reassembly
speed auto
half-duplex
interface Serial0/0
no ip address
shutdown
clock rate 56000
interface FastEthernet0/1
ip address 10.10.10.1 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
router rip
network 1.0.0.0
network 10.0.0.0
no ip forward-protocol nd
ip route 192.168.1.0 255.255.255.0 1.1.1.3
no ip http server
no ip http secure-server
ip nat source list 1 interface FastEthernet0/0 overload
access-list 1 permit 10.10.10.0 0.0.0.255
control-plane
line con 0
line aux 0
line vty 0 4
login
end

I am getting same issure:
Dynamic mappings:
-- Outside Destination
[Id: 1] access-list NAT interface FastEthernet0/0 refcount 0
[0] prot 6: port #0 refcount 2 syscount 2 localport 4294967295, localaddr 0.0.0.
0, flags 1
[0] prot 6: port #7 refcount 1 syscount 1 localport 4294967295, localaddr 0.0.0.
0, flags 1 Dynamic mappings:
-- Outside Destination
[Id: 1] access-list NAT interface FastEthernet0/0 refcount 0
[0] prot 6: port #0 refcount 2 syscount 2 localport 4294967295, localaddr 0.0.0.
0, flags 1
[0] prot 6: port #7 refcount 1 syscount 1 localport 4294967295, localaddr 0.0.0.
0, flags 1
I don't know what this means and will try debug ip nat and get a readout.

Need help opening NAT type to OPEN on a model WRT54GS router for xbox 360

I have tried from other people's advice and when i test Xbox Live i always get a Moderate NAT type. I am becoming frustrated with how it is not working and I am hoping someone can help me. Please leave advice/suggestions and thank you for your time.

Open the setup page of the router using 192.168.1.1 by putting the password as admin with username as blank & click the Administration tab & on the same page you will see UPNP.You need to select it as disable in order to help opening NAT type to OPEN.

PLEASE HELP Portforwarding to open Nat Type Please!

I have a Wireless 2.4 Ghz 54 Mbps Broadband Router. I have seriously spent countless hours trying to get my Nat type open. I have tryed the DMZ route, that didnt work. I really dont know what else to do, any help would be great, Thanks.

you can try the tips here too. http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&articleid=22385
"Don't fix it if it ain't broken."

TS1398 I need help getting connected to our home wifi.

I need help getting connected to our home wifi. I've reset network settings, iPhone, and router but the error "unable to join network" keeps coming up. I also double checked the password. Please help

Other possibilities:
Your router firmware is out of date. Check the manufacturer's website for an update
You have MAC (Media Access Control) filtering enabled on the router, that restricts access to "known" devices and the new iPhone is not on the table of known devices
Your router has a setting limiting the number of simultaneous allowed devices
Your routers SSID ("name") is still the default (e.g., LINKSYS, DLINK, NETGEAR, etc). Your phone has encountered other routers with the same name as you have traveled, and the phone is confused as to which router is the real one. If your router's name is still the default you should change it.

Open NAT type on ps3

When i got my BT home hub 4 in and set my ps3 my nat type was strict... I logged in to the homehub manager and set the ip address as static (i think as thats what id read online to do) anyways it is now on moderate ... How on earth do i get the NAT type to open?? Please help its driving me crazy

Hi Lesleykelly28
This link has no info on the Hub4 but the process should be more or less the same and the Hub 3
http://bt.custhelp.com/app/answers/detail/a_id/32216
give it a try and let me know how you get on.
Thx
Craig
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)”
td-p/30">Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Open NAT type on PS3 from moderate?

Hey,
Ive been wanting to get an open NAT type for a while, ive been unable to would anyone be able to help me?,
i have a BT Infinity Hub 3, im currently on Moderate NAT type
Many Thanks,
Sean

Hi Matt,
Welcome to the forum and thanks for posting. Take a look here for some information on port forwarding. I've also found this whcih you might find useful. Let me know if it helps.
Cheers
David
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)

Need help to open and look for file by name

Hi,
Im needing help to open a folder and look for a file (.txt) on this directory by his name ... The user ll type the partial name of file , and i need look for this file on the folder , and delete it ....
How can i look for the file by his name ?
Thx =)

Hi ,
Sry ,, let me explain again ... I ll set the name of the files in the follow order ... Name_Serial_date_chanel.sxc ..
The user ll type the serial that he wants delete ...
I already figured out what i need guys .. thx for the help ^^
I used List Directory on advanced IO , to list all .. the Name is the same for all ... then i used Name_ concateneted with Serial(typed)* .. this command serial* ll list all serials equal the typed , in my case , ll exist only one , cuz its a count this serial .Then i pass the path to the delete , and its done !
Thx ^^

I need help getting itunes on my new computer. old one crashed

My old computer crashed, I downloaded iTunes on my new computer and need help getting all of my stuff on it that I had. I did 'home share' to see if that worked, and it didnt.
Also, on my old computer, when I synced my iPad & my husbands iPod, it didnt sync any music or podcasts, no videos-and i went through each category seperately to sync it and it didnt work. So I can't sync my devices to the new iTunes bc not everything is on there that i have purchased.

It has always been very basic to always maintain a backup copy of your comuter for just this occasion. Use your backup copy to put everything on the new computer.
If for some reason you have failed to maintain a backup, not good, then you can redownload some itunes purchases in some countries:
Downloading past purchases from the App Store, iBookstore, and iTunes Store

TS4268 I need help getting my face time and imessage to work.

I need help getting my face time and imessage to work. It is saying wating for activation. I just got my iphone 5 2 days ago. I have reset it from the phone and from itunes on the computer, made sure I'm attached to wifi.

The 3 basic troubleshooting steps are these in order: 1. Restart your iphone 2. Reset your settings/iphone 3. Restore your iphone. Since your iphone is only a couple of days old, you should backup your device before restoring. If you don't have anything on your iphone that you care to lose, then simply restoring without a backup is fine. A quick reset of pressing the sleep/wake button (top of iphone) and your home button simultaneously and holding it until the silver Apple logo appears.

Need help getting open nat type on home hub 3 for ...

Similar Messages

Maybe you are looking for