Need help in configuring Cisco AP to support EAP authentication
Hello all,
in desperation after trying for more than 3 weeks, I am trying in this way to get a solution to my following problem.
I am trying to build up as 802.1x scenario using 802.11b infrastructure (RADIUS server, Cisco 1100 Aironet AP, Cisco PCMCIA WLAN card with Xsupplicant software, the complete OS is Linux). I am trying to use EAP-MD5 authentication. It seems that the things are funtioning in standalone mode.
The client wants to authenticate to access WLAN. It sends EAPoL start packet and gets a request from AP for user identity. Good. Then the user sends his identity with EAP packet. The Cisco AP is forwarding the request to RDAIUS server as specified in many documents. It is also Good. RADIUS server is sending a request for challenge (Password). Upto this point things are gooing fine.
Now the Cisco AP is not sending this challenge to the
Xsupplicant, it is just ignoring it. Can any one help me in this point. If needed I can also send the configuration file of the AP.
I would be very thankful, if I could solve this Problem with your support.
Thanking you in advance,
Felix
As per the RFC for RADIUS, a RADIUS Server receiving an Access-Request with a Message- Authenticator Attribute present MUST calculate the correct value of the Message-Authenticator and silently discard the packet if it does not match the value sent. A RADIUS Client receiving an Access-Accept, Access-Reject or Access-Challenge with a Message-Authenticator Attribute present MUST calculate the correct value of the Message-Authenticator and silently discard the packet if it does not match the value sent.
Similar Messages
-
Need help to Configure Cisco ACE 4710 Cluster Deployment
Dear Experts,
I'm newbie for Cisco ACE 4710, and still I'm in learning stage. Meanwhile I got chance at my work place to deploy a Cisco ACE 4710 cluster which should load balance the traffic between two Application Servers based on HTTP and HTTPS traffic. So I was looking for good deployment guide in Cisco SBA knowledge base then finall found this guide.
http://www.cisco.com/en/US/docs/solutions/SBA/February2013/Cisco_SBA_DC_AdvancedServer-LoadBalancingDeploymentGuide-Feb2013.pdf
This guide totally fine with my required deployment model. I have same deployment environment as this guide contains with ACE cluster that connects to two Cisco 3750X (Stack) switches. But I have some confusion places in this guide
This guide follow the "One-armed mode" as a deployment method. But when I go through it further I have noticed that they have configured server VLAN as a 10.4.49.0/24 (all servers reside in it) and Client side VIP also in same VLAN which is 10.4.49.100/24 (even NAT pool also).
My confusion is, as I have learned about Cisco ACE 4710 one-armed mode deployment method, it should has two VLAN segments, one for Client side which client request come and hit the VIP and then second one for Server side. which means besically two VLANs. So please be kind enough to go through above document then tell me where is wrong, what shoud I need to do for the best. Please this is an urgent, so need your help quickly.
Thanks....!
-Amal-Dear Kanwal,
I need quick help for you. Following are the Application LB requirements which I received from my clinet side.
Following detail required for configuring Oracle EBS Apps tier on HA:
LBR IP and Name required to configure EBS APPS Tier (i.e, ap1ebs & ap2ebs nodes)
Suggested IP and Name for LBR:
IP : 172.25.45.x [should be on same 172.25.45 subnet of ap1ebs & ap2ebs nodes]
ebiz.xxxx.lk [on port 80 for http protocol accessibility]
This LBR IP & name must be resolve and respond on DNS network
Server Farm detail for LBR Setup
Following detail will be use for configuring the LBR:
LBR IP and Name :
IP : 172.25.45.x [should be on same 172.25.45 subnet of ap1ebs & ap2ebs nodes]
ebiz.xxxx.lk [on port 80 for http protocol accessibility]
This LBR IP & name must be resolve and respond on DNS network
Server Farm Detail for LBR setup:
Server 1 (EBS App1 Node, ap1ebs):
IP : 172.25.45.19
Server Name: ap1ebs.xxxx.lk [ap1ebs hostname is an example, actual hostname will be use]
Protocol: http
Port: 8000
Server 2 (EBS App2 Node, ap2ebs):
IP : 172.25.45.20
Server Name: ap2ebs.xxxx.lk [ap2ebs hostname is an example, actual hostname will be use]
Protocol: http
Port: 8000
Since my client needs to access URL ebiz.xxxx.lk which should be resolved by IP 172.25.45.21 (virtual IP) via http (80) before they deploy the app on the two servers I just ran web service on both servers (Linux) and was trying to access http://172.25.45.21 it was working fine and gave me index.html page. Now after my client has deployed the application then when he tries to access the page http://172.25.45.21 he cannot see his main login page. But still my testing web servers are there on both servers when I type http://172.25.45.21 it will get index.html page, but not my client web login page. What can I do for this ?
Following are my latest config :
probe http Get-Method
description Check to url access /OA_HTML/OAInfo.jsp
interval 10
faildetect 2
passdetect interval 30
request method get url /OA_HTML/OAInfo.jsp
expect status 200 200
probe udp http-8000-iRDMI
description IRDMI (HTTP - 8000)
port 8000
probe http http-probe
description HTTP Probes
interval 10
faildetect 2
passdetect interval 30
passdetect count 2
request method get url /index.html
expect status 200 200
probe https https-probe
description HTTPS traffic
interval 10
faildetect 2
passdetect interval 30
passdetect count 2
ssl version all
request method get url /index.html
probe icmp icmp-probe
description ICMP PROBE FOR TO CHECK ICMP SERVICE
rserver host ebsapp1
description ebsapp1.xxxx.lk
ip address 172.25.45.19
conn-limit max 4000000 min 4000000
probe icmp-probe
probe http-probe
inservice
rserver host ebsapp2
description ebsapp2.xxxx.lk
ip address 172.25.45.20
conn-limit max 4000000 min 4000000
probe icmp-probe
probe http-probe
inservice
serverfarm host ebsppsvrfarm
description ebsapp server farm
failaction purge
predictor response app-req-to-resp samples 4
probe http-probe
probe icmp-probe
inband-health check log 5 reset 500
retcode 404 404 check log 1 reset 3
rserver ebsapp1 80
conn-limit max 4000000 min 4000000
probe icmp-probe
inservice
rserver ebsapp2 80
conn-limit max 4000000 min 4000000
probe icmp-probe
inservice
sticky http-cookie jsessionid HTTP-COOKIE
cookie insert browser-expire
replicate sticky
serverfarm ebsppsvrfarm
class-map type http loadbalance match-any default-compression-exclusion-mime-type
description DM generated classmap for default LB compression exclusion mime types.
2 match http url .*gif
3 match http url .*css
4 match http url .*js
5 match http url .*class
6 match http url .*jar
7 match http url .*cab
8 match http url .*txt
9 match http url .*ps
10 match http url .*vbs
11 match http url .*xsl
12 match http url .*xml
13 match http url .*pdf
14 match http url .*swf
15 match http url .*jpg
16 match http url .*jpeg
17 match http url .*jpe
18 match http url .*png
class-map match-all ebsapp-vip
2 match virtual-address 172.25.45.21 tcp eq www
class-map type management match-any remote_access
2 match protocol xml-https any
3 match protocol icmp any
4 match protocol telnet any
5 match protocol ssh any
6 match protocol http any
7 match protocol https any
8 match protocol snmp any
policy-map type management first-match remote_mgmt_allow_policy
class remote_access
permit
policy-map type loadbalance first-match ebsapp-vip-l7slb
class default-compression-exclusion-mime-type
serverfarm ebsppsvrfarm
class class-default
compress default-method deflate
sticky-serverfarm HTTP-COOKIE
policy-map multi-match int455
class ebsapp-vip
loadbalance vip inservice
loadbalance policy ebsapp-vip-l7slb
loadbalance vip icmp-reply active
nat dynamic 1 vlan 455
interface vlan 455
ip address 172.25.45.36 255.255.255.0
peer ip address 172.25.45.35 255.255.255.0
access-group input ALL
nat-pool 1 172.25.45.22 172.25.45.22 netmask 255.255.255.0 pat
service-policy input remote_mgmt_allow_policy
service-policy input int455
no shutdown
ft interface vlan 999
ip address 10.1.1.1 255.255.255.0
peer ip address 10.1.1.2 255.255.255.0
no shutdown
ft peer 1
heartbeat interval 300
heartbeat count 10
ft-interface vlan 999
ft group 1
peer 1
no preempt
priority 110
associate-context Admin
inservice
ip route 0.0.0.0 0.0.0.0 172.25.45.1
Hope you will reply me soon
Thanks....!
-Amal- -
Hi All,
I need help on Configuring the Site to Site VPN from Cisco 2811 to Websense Cloud for web Traffic redirect
2811 having C2800NM-ADVIPSERVICESK9-M
2811 router connects to the Internet SW then connects to the Internet router.
Note- For Authentication am using the Device ID & Pre share key. I am worried as all user traffic goes with PAT and not firing up my tunnel for port 80 traffic. Can you please suggest what can be the issue ?
Below is router config for VPN & NAT
crypto keyring ISR_Keyring
pre-shared-key hostname vpn.websense.net key 2c22524d554556442d222d565f545246
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp keepalive 10
crypto isakmp profile isa-profile
keyring ISR_Keyring
self-identity user-fqdn [email protected]
match identity user vpn-proxy.websense.net
crypto ipsec transform-set ESP-NULL-SHA esp-null esp-sha-hmac
crypto map GUEST_WEB_FILTER 10 ipsec-isakmp
set peer vpn.websense.net dynamic
set transform-set ESP-NULL-SHA
set isakmp-profile isa-profile
match address 101
interface FastEthernet0/1
description connected to Internet
ip address 216.222.208.101 255.255.255.128
ip access-group HVAC_Public in
ip nat outside
ip virtual-reassembly
duplex full
speed 100
no cdp enable
crypto map GUEST_WEB_FILTER
access-list 101 permit tcp 192.168.8.0 0.0.3.255 any eq www
access-list 103 deny ip 192.168.8.0 0.0.3.255 host 85.115.41.187 log
access-list 103 deny ip 192.168.8.0 0.0.3.255 host 85.115.41.181 log
access-list 103 deny ip 192.168.8.0 0.0.3.255 host 85.115.41.182 log
access-list 103 deny ip 192.168.8.0 0.0.3.255 86.111.216.0 0.0.1.255
access-list 103 deny ip 192.168.8.0 0.0.3.255 116.50.56.0 0.0.7.255
access-list 103 deny ip 192.168.8.0 0.0.3.255 86.111.220.0 0.0.3.255
access-list 103 deny ip 192.168.8.0 0.0.3.255 103.1.196.0 0.0.3.255
access-list 103 deny ip 192.168.8.0 0.0.3.255 177.39.96.0 0.0.3.255
access-list 103 deny ip 192.168.8.0 0.0.3.255 196.216.238.0 0.0.1.255
access-list 103 permit ip 192.168.8.0 0.0.3.255 any
ip nat pool mypool 216.222.208.101 216.222.208.101 netmask 255.255.255.128
ip nat inside source list 103 interface FastEthernet0/1 overload
ip nat inside source route-map nonat pool mypool overloadHow does Websense expect your source IPs in the tunnel? 192.168.8.0 0.0.3.255 or PAT'ed 216.222.208.101 ?
Check
show crypto isakmp sa
show crypto ipsec sa
show crypto session
You'd better remove the preshared key from your post. -
I really need help. I try to contact support to no avail. There simply is no option on the site, You are always referred to a further topic which has notihing to do with my problem. I bougnt a full master pack CS6 which I had installed on a mac for one year. Then, I decided to change it to another computer, so I sisintalled it according to instructions. In the meantime I got a free trial of creative cloud on that computer, but I gave up and decided to reinstall my cd-roms. However, everytime I try to use acrobat for instance it says that my trial period ran out! I disinstalled my cloud products, I am using my registered full master series items, they have nothing whatsoever to do with my creative cloud FREE subscription. If I try to cancel my free membership, it is to no avail, there simply is no such possiblity. I want to use the software I paid dearly for, not the cloud items I disinstalled and which do not interest me. How can I contact Adobe to fix it? It was no fault of mine, I did all I was supposed to, disintalling items before installing the right ones, but the system must have some error i am not responsible for.
open an app and click help>activate.
if you try to open an app and see a 'your trial has expired" window, click license this software and enter your serial number.
if you can't do either, run the cleaner and make sure cc is cleaned from your computer, Use the CC Cleaner Tool to solve installation problems | CC, CS3-CS6 -
I have a PC and a need help to configure my external hard disk on my network. Thanks
I have a PC and a need help to configure my external hard disk on my network. Thanks
If you mean you wish to plug a USB drive into the Airport Extreme router (or TC not express) that is easy..
The disk must be formatted FAT32.. as if.. stay away from FAT .. or HFS+ ie Mac OS extended Journaled.
Format the disk on a Mac is best.. and even use GUID partition scheme not MBR.
The PC has no issue writing and reading files because this is a network drive.. The PC does not write to the drive.. it writes files to the Airport OS which writes and reads the disk and passes the info using standard windows SMB.. To the windows computer it will be a Windows NT server.. FAT32 setup.
If your setup is different.. to my hugely guessed assumptions.. give details.. always helps to have.. make and model.
Make and model of disk.. make and model of router.. how the setup will be done.. what windows OS you run.. etc etc.
As it stands your question could have nothing to do with apple at all.. other than you posted in a forum so I guess there is something apple in there somewhere. -
Need urgent help in configuring Client to Site IPSec VPN with Hairpinning on Cisco ASA5510 - 8.2(1).
The following is the Layout:
There are two Leased Lines for Internet access - 1.1.1.1 & 2.2.2.2, the latter being the Standard Default route, the former one is for backup.
I have been able to configure Client to Site IPSec VPN
1) With access from Outside to only the Internal Network (172.16.0.0/24) behind the asa
2) With Split tunnel with simultaneous assess to internal LAN and Outside Internet.
But I have not been able to make tradiotional Hairpinng model work in this scenario.
I followed every possible sugestions made in this regard in many Discussion Topics but still no luck. Can someone please help me out here???
Following is the Running-Conf with Normal Client to Site IPSec VPN configured with No internat Access:
LIMITATION: Can't Boot into any other ios image for some unavoidable reason, must use 8.2(1)
running-conf --- Working normal Client to Site VPN without internet access/split tunnel
ASA Version 8.2(1)
hostname ciscoasa
domain-name cisco.campus.com
enable password xxxxxxxxxxxxxx encrypted
passwd xxxxxxxxxxxxxx encrypted
names
interface GigabitEthernet0/0
nameif internet1-outside
security-level 0
ip address 1.1.1.1 255.255.255.240
interface GigabitEthernet0/1
nameif internet2-outside
security-level 0
ip address 2.2.2.2 255.255.255.224
interface GigabitEthernet0/2
nameif dmz-interface
security-level 0
ip address 10.0.1.1 255.255.255.0
interface GigabitEthernet0/3
nameif campus-lan
security-level 0
ip address 172.16.0.1 255.255.0.0
interface Management0/0
nameif CSC-MGMT
security-level 100
ip address 10.0.0.4 255.255.255.0
boot system disk0:/asa821-k8.bin
boot system disk0:/asa843-k8.bin
ftp mode passive
dns server-group DefaultDNS
domain-name cisco.campus.com
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group network cmps-lan
object-group network csc-ip
object-group network www-inside
object-group network www-outside
object-group service tcp-80
object-group service udp-53
object-group service https
object-group service pop3
object-group service smtp
object-group service tcp80
object-group service http-s
object-group service pop3-110
object-group service smtp25
object-group service udp53
object-group service ssh
object-group service tcp-port
object-group service udp-port
object-group service ftp
object-group service ftp-data
object-group network csc1-ip
object-group service all-tcp-udp
access-list INTERNET1-IN extended permit ip host 1.2.2.2 host 2.2.2.3
access-list CSC-OUT extended permit ip host 10.0.0.5 any
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq www
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq https
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq ssh
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq ftp
access-list CAMPUS-LAN extended permit udp 172.16.0.0 255.255.0.0 any eq domain
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq smtp
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq pop3
access-list CAMPUS-LAN extended permit ip any any
access-list csc-acl remark scan web and mail traffic
access-list csc-acl extended permit tcp any any eq smtp
access-list csc-acl extended permit tcp any any eq pop3
access-list csc-acl remark scan web and mail traffic
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq 993
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq imap4
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq 465
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq www
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq https
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq smtp
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq pop3
access-list INTERNET2-IN extended permit ip any host 1.1.1.2
access-list nonat extended permit ip 172.16.0.0 255.255.0.0 172.16.0.0 255.255.0.0
access-list DNS-inspect extended permit tcp any any eq domain
access-list DNS-inspect extended permit udp any any eq domain
access-list capin extended permit ip host 172.16.1.234 any
access-list capin extended permit ip host 172.16.1.52 any
access-list capin extended permit ip any host 172.16.1.52
access-list capin extended permit ip host 172.16.0.82 host 172.16.0.61
access-list capin extended permit ip host 172.16.0.61 host 172.16.0.82
access-list capout extended permit ip host 2.2.2.2 any
access-list capout extended permit ip any host 2.2.2.2
access-list campus-lan_nat0_outbound extended permit ip 172.16.0.0 255.255.0.0 192.168.150.0 255.255.255.0
pager lines 24
logging enable
logging buffered debugging
logging asdm informational
mtu internet1-outside 1500
mtu internet2-outside 1500
mtu dmz-interface 1500
mtu campus-lan 1500
mtu CSC-MGMT 1500
ip local pool vpnpool1 192.168.150.2-192.168.150.250 mask 255.255.255.0
ip verify reverse-path interface internet2-outside
ip verify reverse-path interface dmz-interface
ip verify reverse-path interface campus-lan
ip verify reverse-path interface CSC-MGMT
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-621.bin
no asdm history enable
arp timeout 14400
global (internet1-outside) 1 interface
global (internet2-outside) 1 interface
nat (campus-lan) 0 access-list campus-lan_nat0_outbound
nat (campus-lan) 1 0.0.0.0 0.0.0.0
nat (CSC-MGMT) 1 10.0.0.5 255.255.255.255
static (CSC-MGMT,internet2-outside) 2.2.2.3 10.0.0.5 netmask 255.255.255.255
access-group INTERNET2-IN in interface internet1-outside
access-group INTERNET1-IN in interface internet2-outside
access-group CAMPUS-LAN in interface campus-lan
access-group CSC-OUT in interface CSC-MGMT
route internet2-outside 0.0.0.0 0.0.0.0 2.2.2.5 1
route internet1-outside 0.0.0.0 0.0.0.0 1.1.1.5 2
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
aaa authentication enable console LOCAL
http server enable
http 10.0.0.2 255.255.255.255 CSC-MGMT
http 10.0.0.8 255.255.255.255 CSC-MGMT
http 1.2.2.2 255.255.255.255 internet2-outside
http 1.2.2.2 255.255.255.255 internet1-outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map internet2-outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map internet2-outside_map interface internet2-outside
crypto ca trustpoint _SmartCallHome_ServerCA
crl configure
crypto ca certificate chain _SmartCallHome_ServerCA
certificate ca xyzxyzxyzyxzxyzxyzxyzxxyzyxzyxzy
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as
quit
crypto isakmp enable internet2-outside
crypto isakmp policy 10
authentication pre-share
encryption aes
hash md5
group 2
lifetime 86400
telnet 10.0.0.2 255.255.255.255 CSC-MGMT
telnet 10.0.0.8 255.255.255.255 CSC-MGMT
telnet timeout 5
ssh 1.2.3.3 255.255.255.240 internet1-outside
ssh 1.2.2.2 255.255.255.255 internet1-outside
ssh 1.2.2.2 255.255.255.255 internet2-outside
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy VPN_TG_1 internal
group-policy VPN_TG_1 attributes
vpn-tunnel-protocol IPSec
username ssochelpdesk password xxxxxxxxxxxxxx encrypted privilege 15
username administrator password xxxxxxxxxxxxxx encrypted privilege 15
username vpnuser1 password xxxxxxxxxxxxxx encrypted privilege 0
username vpnuser1 attributes
vpn-group-policy VPN_TG_1
tunnel-group VPN_TG_1 type remote-access
tunnel-group VPN_TG_1 general-attributes
address-pool vpnpool1
default-group-policy VPN_TG_1
tunnel-group VPN_TG_1 ipsec-attributes
pre-shared-key *
class-map cmap-DNS
match access-list DNS-inspect
class-map csc-class
match access-list csc-acl
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class csc-class
csc fail-open
class cmap-DNS
inspect dns preset_dns_map
service-policy global_policy global
prompt hostname context
Cryptochecksum: y0y0y0y0y0y0y0y0y0y0y0y0y0y
: end
Neither Adding dynamic NAT for 192.168.150.0/24 on outside interface works, nor does the sysopt connection permit-vpn works
Please tell what needs to be done here, to hairpin all the traffic to internet comming from VPN Clients.
That is I need clients conected via VPN tunnel, when connected to internet, should have their IP's NAT'ted against the internet2-outside interface address 2.2.2.2, as it happens for the Campus Clients (172.16.0.0/16)
I'm not much conversant with everything involved in here, therefore please be elaborative in your replies. Please let me know if you need any more information regarding this setup to answer my query.
Thanks & Regards
maxsHi Jouni,
Thanks again for your help, got it working. Actually the problem was ASA needed some time after configuring to work properly ( ?????? ). I configured and tested several times within a short period, during the day and was not working initially, GUI packet tracer was showing some problems (IPSEC Spoof detected) and also there was this left out dns. Its working fine now.
But my problem is not solved fully here.
Does hairpinning model allow access to the campus LAN behind ASA also?. Coz the setup is working now as i needed, and I can access Internet with the NAT'ed ip address (outside-interface). So far so good. But now I cannot access the Campus LAN behind the asa.
Here the packet tracer output for the traffic:
packet-tracer output
asa# packet-tracer input internet2-outside tcp 192.168.150.1 56482 172.16.1.249 22
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
MAC Access list
Phase: 2
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
Additional Information:
Found no matching flow, creating a new flow
Phase: 3
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 172.16.0.0 255.255.0.0 campus-lan
Phase: 4
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 192.168.150.1 255.255.255.255 internet2-outside
Phase: 5
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group internnet1-in in interface internet2-outside
access-list internnet1-in extended permit ip 192.168.150.0 255.255.255.0 any
Additional Information:
Phase: 6
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 7
Type: CP-PUNT
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 8
Type: VPN
Subtype: ipsec-tunnel-flow
Result: ALLOW
Config:
Additional Information:
Phase: 9
Type: NAT-EXEMPT
Subtype: rpf-check
Result: ALLOW
Config:
Additional Information:
Phase: 10
Type: NAT
Subtype:
Result: DROP
Config:
nat (internet2-outside) 1 192.168.150.0 255.255.255.0
match ip internet2-outside 192.168.150.0 255.255.255.0 campus-lan any
dynamic translation to pool 1 (No matching global)
translate_hits = 14, untranslate_hits = 0
Additional Information:
Result:
input-interface: internet2-outside
input-status: up
input-line-status: up
output-interface: internet2-outside
output-status: up
output-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule
The problem here as you can see is the Rule for dynamic nat that I added to make hairpin work at first place
dynamic nat
asa(config)#nat (internet2-outside) 1 192.168.150.0 255.255.255.0
Is it possible to access both
1)LAN behind ASA
2)INTERNET via HAIRPINNING
simultaneously via a single tunnel-group?
If it can be done, how do I do it. What changes do I need to make here to get simultaneous access to my LAN also?
Thanks & Regards
Abhijit -
Need help with configuring a Printer Driver in Oracle apps
Hi,
We have set of interfaces/concurrent jobs which are programed to send the output file to file location1. Now we need to direct the output for all these jobs to file location2. The idea is to not modify the existing code, but have configuration in place which will re-direct the output files to the new “file location2”, once the concurrent job run is complete.
We have come across “Using Dummy Printer driver” option wherein we created a dummy printer driver with arguments as below and attached this printer to all these concurrent jobs.
mv <file location1>/$PROFILES$.TITLE <file location2>
This option is working fine if both the file locations are hard coded. But both these locations are configured in 2 separate profile options and the filepath would change from once Oracle instance to another.
We are looking for solutions where we can pass the profile option value to this printer driver instead of hardcoding it in the argument.
Also, please suggest any other solution to move the output files to a different location.
Please note that our client is on Oracle On-Demand environment (apps – 11.5.10) and hence a shell script cannot be used for this.
Thanks,
Kiranmayi.Hello Mark,
I can't support the netopia router/modem, but I would think there should be an admin guide for the configuration. If it is a modem/router and you said there is rules for allowing or blocking services, which sounds like access list you should be able to create a rule for the client you want to block on the modem/router to prevent it from talking to the internet.
If you want to insure no outside security threats can make it to the computer staticly assign an IP address but don't give it a default gateway address. The client will not be able to talk to any other network but its own. It sounds like you only have one vlan or a flat network so this should work, but if you need to be able to have this computer in the future talk to other networks internally then it isn't a viable solution. Blocking at the modem/router would be the only solution.
The SG300-08 Switch you could setup an ACL to block that client from talking to the modem/router, but the potential for causing valid traffic from being blocked in your own network grows.
To create this rule you would first
go to Access Control
Create a MAC Base ACL (give it a meaning full name)
Create 2 a MAC BASE ACE
Rule 1
Priority 10
Action Deny
Destination Any
Source User Defined
MAC address of client wanting to be blocked
Apply
Rule 2
Priority 20
Action Permit
Destination Any
Source Any
Apply
Bind the ACL to a port
Make sure to only bind the ACL to the port that connects to the router/modem.
Cisco Small Business Support Center
Randy Manthey
CCNA, CCNA - Security -
Need help with configuring a particular setting on SF300-08
I work for a small business and we have a couple computers that we want to share a ethernet enabled copier/printer with, but for security reasons want to block those computers from internet access. How would one go about allowing that?
Thanks in advance,
Mark DavisHello Mark,
I can't support the netopia router/modem, but I would think there should be an admin guide for the configuration. If it is a modem/router and you said there is rules for allowing or blocking services, which sounds like access list you should be able to create a rule for the client you want to block on the modem/router to prevent it from talking to the internet.
If you want to insure no outside security threats can make it to the computer staticly assign an IP address but don't give it a default gateway address. The client will not be able to talk to any other network but its own. It sounds like you only have one vlan or a flat network so this should work, but if you need to be able to have this computer in the future talk to other networks internally then it isn't a viable solution. Blocking at the modem/router would be the only solution.
The SG300-08 Switch you could setup an ACL to block that client from talking to the modem/router, but the potential for causing valid traffic from being blocked in your own network grows.
To create this rule you would first
go to Access Control
Create a MAC Base ACL (give it a meaning full name)
Create 2 a MAC BASE ACE
Rule 1
Priority 10
Action Deny
Destination Any
Source User Defined
MAC address of client wanting to be blocked
Apply
Rule 2
Priority 20
Action Permit
Destination Any
Source Any
Apply
Bind the ACL to a port
Make sure to only bind the ACL to the port that connects to the router/modem.
Cisco Small Business Support Center
Randy Manthey
CCNA, CCNA - Security -
Need help estimating processing power required to support new process
Hi,
I am putting up a new server spec for a new project. I need help estimating processor power I need.
Here are, in short, the steps of the main process:
- Load the data:
Incoming file contains 160 mln rows. The SIZE of this file is 250 GB. The file has about 60 columns, out of that I upload 50 into my table.
Record length is 1500 bytes, in the table.
- Validation/calculations:
After the upload I validate EACH row in this table against 20 rules that are defined in the RULES table.
It is all math, like this column plus that column must be equal to this number, and validate the third column against this number.
- Output stage:
Records that pass validation go to one table, those that didn't go to the other table.
Then the first table (with good records) is extracted to a file. Those from the "wrong" table are also get inserted into "review" table
This whole process should take about 5-6 hrs.
This file contains 6 month of data.
Some times, I will run validation against 2 year worth of data, means validate two "annual" tables, each one is 500 GB in size. According to the requirements, this process should take no more than 1 day.
For this process I write hardware spec for a new server.
I have a hard time figuring out how much processor power I need for this process? to validate this much data in that much time.
Is there any formula or a guideline to tell what processor I need? I was looking at this one, but I wish I could estimate before I buy and try (and possibly fail, and have a biiiiig problems)
Intel Xeon E5-2640 (6 core, 2.50 GHz, 15MB, 95W)
Number of processors: 2
RAM: 16GB
Any help is very appreciated.
Thanks in advance
Edited by: 933238 on Jun 13, 2012 12:25 PM
Edited by: 933238 on Jun 13, 2012 12:28 PMHello Ajay,
Please have a look to these blogs (the second one should be particularly interesting regarding your request) :
/people/kamran.ellahi2/blog/2006/01/13/setting-up-sap-service-desk-123-and-go
/people/dolores.correa/blog/2007/10/06/service-desk-support-team-determination
Hope this helps.
BR.
Stéphane. -
Need Help for configuring Floating static route in My ASA.
Hi All,
I need your support for doing a floating static route in My ASA.
I have tried this last time but i was not able to make it. But this time i have to Finish it.
Please find our network Diagram and configuration of ASA
route outside 0.0.0.0 0.0.0.0 6.6.6.6 1 track 1
route outside 0.0.0.0 0.0.0.0 6.6.6.6 1
route rOutside 0.0.0.0 0.0.0.0 3.3.3.3 10
route inside 10.10.4.0 255.255.255.0 10.10.3.1 1
route inside 10.10.8.0 255.255.255.0 10.10.3.1 1
route inside 10.10.9.0 255.255.255.0 10.10.3.1 1
route inside 10.10.15.0 255.255.255.0 10.10.3.1 1
route rOutside x.x.x.x 255.255.255.255 5.5.5.5 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 10.10.3.77 255.255.255.255 inside
http 10.10.8.157 255.255.255.255 inside
http 10.10.3.59 255.255.255.255 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
sla monitor 123
type echo protocol ipIcmpEcho 8.8.8.8 interface outside
num-packets 3
frequency 10
sla monitor schedule 123 life forever start-time now
crypto ipsec transform-set cpa esp-3des esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map vpn_cpa 1 match address acl_cpavpn
crypto map vpn_cpa 1 set peer a.a.a.a
crypto map vpn_cpa 1 set transform-set abc
crypto map vpn_cpa 1 set security-association lifetime seconds 3600
crypto map vpn_cpa interface outside
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto isakmp policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
track 1 rtr 123 reachability
telnet 10.10.3.77 255.255.255.255 inside
telnet 10.10.8.157 255.255.255.255 inside
telnet 10.10.3.61 255.255.255.255 inside
telnet timeout 500
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics port
threat-detection statistics protocol
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp server 10.10.3.14
webvpn
tunnel-group .a.a.a.a ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
smtp-server 10.10.5.11
prompt hostname context
Cryptochecksum:eea6e7b6efe5d1a180439658c3912942
: end
i think half of the configuration stil there in the ASA.
Diagram.
Thanks
RoopeshYou have missed the last command in your configuration, Please check it again
route ISP1 0.0.0.0 0.0.0.0 6.6.6.6 track 1
route ISP2 0.0.0.0 0.0.0.0 3.3.3.3
sla monitor 10
type echo protocol ipIcmpEcho 8.8.8.8 interface ISP1
num-packets 3
frequency 10
sla monitor schedule 123 life forever start-time now
track 1 rtr 123 reachability
You can do NAT in same way, here the logical name of the interface will be different.
Share the result
Please rate any helpful posts. -
Need help to configure my mac...
Hi, guys! So my Mac finally arrived yesterday and now I´m officially a happy mac user!
However, as a new one, I need some help getting around... So I have 2 questions:
1) is there any special configuration I should use to make it faster? Let me explain myself better: before I bought my macbook, I tried one out at my local store (an i5, 320 HDD, 4Gb RAM) and it was so fast it impressed me! Iphoto, for instance, would launch faster than I could blink, it was incredibily fast. Mty macbook, however, is not that fast (even though it´s an i7...). Iphoto will take about 6-8 seconds to launch in my own computer (and pictures are not even there yet!), which is a serious delay compared to what I´ve seen at store, so I wonder if that´s a misconfiguration issue, something I´m doing wrong... By the way, all the software installed in the machine is up-to-date.
2) my screen is high resolution and pictures/images look great on it, but the fonts seem to be too small. I have looked around but couldn´t find an option to keep the maximum video resolution while making fonts a little bigger at the same time. Is there a way to do that like there is in windows?
Ok, so thank you for reading, I really appreciate any help I can get!
Cheers,
Renata1) is there any special configuration I should use to make it faster? Let me explain myself better: before I bought my macbook, I tried one out at my local store (an i5, 320 HDD, 4Gb RAM) and it was so fast it impressed me! Iphoto, for instance, would launch faster than I could blink, it was incredibily fast. Mty macbook, however, is not that fast (even though it´s an i7...). Iphoto will take about 6-8 seconds to launch in my own computer (and pictures are not even there yet!), which is a serious delay compared to what I´ve seen at store, so I wonder if that´s a misconfiguration issue, something I´m doing wrong... By the way, all the software installed in the machine is up-to-date.
Number one, do not buy cache cleaning software. This will actually slow your system down.
Number two, keep at least two copies of your data at all times*:
http://www.macmaps.com/backup.html
Once you are happy with your backup, leave your machine on overnight. This runs scripts you can also run with tools such as Macjanitor or Anacron manually.
Occassionally you might want to check your directory status*:
http://www.macmaps.com/directoryfaq.html
Don't let your system get too full*:
http://www.macmaps.com/diskfull.html
Run the hardware test that came with your system while it is still under warranty.
http://support.apple.com/kb/HT1509
Buy AppleCare in the first year, so you have warranty for three years from date of computer's purchase.
Apple menu -> System Preferences -> Displays lets you change the screen resolution an color tone of your machine for better legibility.
Apple menu -> System Preferences -> Universal Access has a magnification feature if it is still is illegible.
- * Links to my pages may give me compensation.
Message was edited by: a brody -
Need help to Configure FTPS connection for File Sender Adapter
Hi,
I want to Configure, FTPS connection (Secured Connection) for File Sender Adapter. Could anyone please guide me, what Information I require to configure. I just want to know what Information should I request the team inorder the configure FTPS so that it can be deployed properly.
I have checked with [SAP Help Link|http://help.sap.com/saphelp_nw04/helpdata/EN/e3/94007075cae04f930cc4c034e411e1/content.htm] and while configuring the communication channel found that I need Keystore and the X.509 Certificate and Private Key. which needs to be deployed on the J2EE server by using the Visual Administrator.
Is there anything else, I need to configure.
Any help would be appreciated in this regard.
Thanks & Regards,
Varun.KThe basic things are Certificate/Keys which you already know. Usually it is enough for running a sceanrio.
However, if you have additional requirements, like FTPS for "Connection Security" for encryption, then you may need additional details like commands. Rest all settings are same as FTP.
Regards,
Prateek -
Need Help on Configurations of Data Services on IBM AIX Platform
Hi All,
We are in the process of installing Data Services XI 3.2 on IBM AIX platform.We are having some showstoppers which we are not able to resolve.
It would be of great help to us if anyone can give some inputs.
Lanscape:
Data services server: Server A
OS - AIBM AIX
DB2 Database: Server B
OS - AIBM AIX
Activities Performed till now on DB2 Side:
Multi user development:
1. Created 2 DBu2019s on Server B
· REPO_CR (Central Repository u2013 Which is used for multi-user environment).
· REPO_LR (Local Repository u2013 Which is used for actual development like login and build jobs).
2. Created multiple schemas under REPO_LR(One Schema for each user).
· User1, User2, User3, etcu2026 (These schemas can hold metadata of Data Services XI which can be used for reference).
Each and every schema should have itu2019s their own user name and password
Activities Performed till now on Data Services Side:
1.Installed Dataservices
Activities Yet to be done on Data Services Side:
1.Configure Repository manager (Create central repository REPO_CR of type sucure using repository manager)
2.Configure Job Server(Create a Job server and assign the local repository REPO_LR to the same)
Issues:
While creating the central repository usning the below command:
./repoman -UCRREP -Ppassword -SServer B -NDB2 -QREPO_CR -tcentral -c -a -d
an error ocurred as :"Error while creating the Local Repository"
I think we are getting this error because of some connectivity issue between DB2 server and Data services Server.
Please share all of your valuable thoughts.
Note:Our DB2 admin said we cannot create any ODBC connections on AIX platform
Thanks,
Munithe arguments that you are passing to repoman are not correct, if your server name has space then you should enclose that in quotes, else it will be treated as 2 arguments, you are passing -SServer B it should be -S"Server B"
-SServer B
I don't think you need to pass -Q option for DB2, its required only for Sybase Repo
for DB2 you will have to install the DB2 Client, and create a Node and Catalog the database on that node
if you are able to open DB2 command prompt form the unix and use that database, then try using the following args to create DB2 Repo
-Uusername -Ppassword -NDB2 -SDBName -tcentral -c -a -d
or better use Repository Manager from Windows to create repos -
New to sap - need help in configure backup strategy for SAP XI server.
hi gurus
being a netweaver guy, recently i have been given the responsibility of few basis activities.like database backup.
can any one tell me clear procedure to take both daily online and weekend full offline backup of oracle in to disk first and then to tape. i have seen in the internet material few discussing about brbackup and few about sap DB13. i am totally confused which one to use, and which is good. please help
akhilHi,
welcome on board as SAP Netweaver guy,
don't be confused both DB13 and BRtools are the same both of them will call brbackup.
to configure the brtools you have to change in your brtools profiles located at %ORACLE_HOME%/dbs
please before changing any thing take backup from that folder.
- to take the backup to disk then to tape you will need extra backup software, because using the SAP slandered tools you have to select either Disk or Tape.
Thanks
Sherif -
Need help regarding configuring the WebService Call from RTD to Siebel
Hi All,
Can someone help me with the information on how do i configure a Webservice Call from RTD to Siebel?
Any high-level or granular details on this would be very helpful as I am new working on this product. How can a jax-ws be utilized to achieve the same?
Thanks in advance.
Best Regards,
HariharanIf you actually need a portal service though, this will not work. However, you could have the portal service return a Document object, which is basically the text of the HTML file you want to display. Then, when calling the portal service, you can simply output the text to the IPortalComponentResponse object
I hope this helps
Darrell
Maybe you are looking for
-
i have a mixer which i was using with my pc and now i bought a new macbook and it have only one jack for headphones and to use mixers i need jack for microphone too so what should i do
-
How to read the content of .msg file type with attachments in SAP crm?
Hi All, Need to develop a RFC FM which will take any BP number as input Read the attachments in the BP and identify the attachment which is an email( .msg). Identify by the mime type and file extension Scan through the email to get the attachments of
-
What is the best full protection case for the iphone 4/s
Can you guys tell me ASAP what is the best full protection iphone 4s case around, i want an all around protection case like lifeproof, i have hesard they are bad cases is that true.
-
Blank row in table....
Hi all, I have a serious problem with the table UI. In screen 1 ,I have a table where I multiselect the table rows and press "next Button" this action leads to the Screen 2, where a summary of the previously selected rows is displayed.. Here
-
Save Output Xml Generated During Bursting Process To Database
Hi All, I am using BI Publisher 10.1.3.4.1 to geneate pdf invoices from xml file. One xml file contains around 10k invoices. During bursting process, I can see that xml file for each individual invoice is generated in the log directory along with som