Need help InterVlan Routing on SF300-24P? .

Hello
I really need help with Inter vlan routing via Kerio Controll 7.4.1.
I have several SF300-24P switches (IOS 1.3.0.62) and i have created a several VLAN's.
Vlans: Vlan 10, 100, 200 and interface vlan 213 (for management).
I can ping hosts in the same Vlan via this switches. From switch to host, port is in access mode and between switches ports is in Trunk mode
(also i had a problem here, trunk wasn't working untill i used command: switchport trunk allowed vlan add all).
Also port is in Trunk mode between KERIO and SW1 (switch). interface is in TRUNK mode from switch's side because i don't know how configure interface TRUNK mode on kerio.
On kerio i have configed one physical interface with IP - 172.16.0.1 255.255.255.0 and on the same interface i have created
VLAN 10, VLAN 100 and VLAN 200.
static IP's for this interfaces:
10.0.0.1 255.255.255.0 VLAN 10
192.168.100.1 255.255.255.0 VLAN 100
192.168.200.1 255.255.255.0 VLAN 200
On KERIO i have created DHCP Lease for each VLAN, but i cannot get IP's from DHCP. So i assigned static IP's to computers
(for example for VLAN100 PC, VLAN 200 PC and so on) but they cannot ping each other when they are in different vlans, so inter vlan routing itsnot working. but with static IP on the PC, i can ping every VLAN's IP address on KERIO.
so pls tell me how i must configure inter vlan routing on kerio, is it possible?
or what must i do? where is my mistake? maybe when i put IP on pysical interface?
here is my configs and pls help and give me config example.
config-file-header
SW1
v1.3.0.62 / R750_NIK_1_3_647_260
CLI v1.0
set system mode switch
file SSD indicator plaintext
vlan database
vlan 10,100,200,213
exit
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
hostname SW1
username administrator password encrypted 7fc3774d79570c81cda124d5dcf80b8ae0fcdd6c privilege 15
username cisco password encrypted 1defefd1f4a214009775b2c2b6b961a77da384b5 privilege 15
interface vlan 10
name Staff
interface vlan 100
name Cards
interface vlan 200
name AP's
interface vlan 213
name Management
ip address 172.16.213.1 255.255.255.0
no ip address dhcp
interface fastethernet1
description MANAGEMENT-VLAN
spanning-tree disable
switchport mode access
switchport access vlan 213
interface fastethernet2
spanning-tree disable
switchport mode general
switchport general acceptable-frame-type untagged-only
interface fastethernet3
spanning-tree disable
switchport mode general
switchport general acceptable-frame-type untagged-only
interface fastethernet4
spanning-tree disable
switchport mode access
switchport access vlan 200
interface fastethernet5
spanning-tree disable
switchport mode access
switchport access vlan 200
interface fastethernet6
spanning-tree disable
switchport mode access
switchport access vlan 100
interface fastethernet7
spanning-tree disable
switchport mode access
switchport access vlan 100
interface gigabitethernet1
description Direction-To-SW2       <--- This port is Trunk, but its not showing here for some reason.
spanning-tree disable
interface gigabitethernet2
description Direction-To-KERIO <--- This port is Trunk also.   i used: switchport mode trunk on both interfaces
spanning-tree disable
exit
banner login
SW1
config-file-header
SW2
v1.3.0.62 / R750_NIK_1_3_647_260
CLI v1.0
set system mode switch
file SSD indicator encrypted
ssd-control-start
ssd config
ssd file passphrase control unrestricted
no ssd file integrity control
ssd-control-end cb0a3fdb1f3a1af4e4430033719968c0
vlan database
vlan 10,100,200,213
exit
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
hostname SW2
username administrator password encrypted 7fc3774d79570c81cda124d5dcf80b8ae0fcdd6c privilege 15
username cisco password encrypted 1defefd1f4a214009775b2c2b6b961a77da384b5 privilege 15
interface vlan 10
name Staff
interface vlan 100
name Cards
interface vlan 200
name AP's
interface vlan 213
name Management
ip address 172.16.213.2 255.255.255.0
no ip address dhcp
interface fastethernet1
description MANAGEMENT-VLAN
spanning-tree disable
switchport mode access
switchport access vlan 213
interface fastethernet2
spanning-tree disable
switchport mode general
switchport general acceptable-frame-type untagged-only
interface fastethernet3
spanning-tree disable
switchport mode general
switchport general acceptable-frame-type untagged-only
interface fastethernet4
spanning-tree disable
switchport mode access
switchport access vlan 200
interface fastethernet5
spanning-tree disable
switchport mode access
switchport access vlan 200
interface fastethernet6
spanning-tree disable
switchport mode access
switchport access vlan 100
interface fastethernet7
spanning-tree disable
switchport mode access
switchport access vlan 100
interface fastethernet8
spanning-tree disable
switchport mode access
switchport access vlan 100
interface gigabitethernet1
description Direction-To-SW1    <--- This port is Trunk also.   i used: switchport mode trunk
exit
banner login
SW2
i have excluded many interfaces because hey have same configs.

Yes Kerio is capable for routing. i wanted to make InterVlan routing via kerio Ccontroll, but i can't and that's i asked here, i need to know reason.
I have modified 1 switch to L3, and inter vlan routing its now working (without Kerio) and i hope this switches dont have problem when they are DHCP server also.
thanx for help. I Hope i didnot have much mistakes in config.

Similar Messages

Need to access settings of SF300-24p

Hi I was just recently hired in my company, we have an sf300-24p switch but I cant find the console cable for it, I think it needs a female to female db9 serial cable, all I have is a DB9 serial to rj45 console cable for the 2801 router, also I cant find the IP address of the sf300 switch, it is directly connected to the 2801 router, I issued a show arp to the router but didnt find the switch's IP add for web access, to sum it up I have no way of configuring the switch, is there any way to find the IP address of the switch? It also dosnt show on show cdp neighbors, thanks!

Daniele,
You would be able to do something similar, password recovery, if you had the serial cable.
I'll update this post with instructions in a minute. I don't know if this is a project you need to get done today, but it sounds like that serial cable will make your life a heck of a lot simpler. If you can't wait to order one, is there somewhere you can get one locally?
Best,
David
Password recovery steps:
You'll need a serial connection to the switch with the following serial connections settings (I'm using Putty in the screenshot):
You will see a prompt during boot right after the cisco logo made out of #s that says "Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom."
Hit return, and you will get the following startup menu:
You'll want [3] Password Recovery Procedure and follow the prompts to reset the password without erasing your config file.

Need help selecting router

Hello All,
I need some help in selecting the best router for our wireless setup. I have never setup a wireless network, so please forgive if I am a little lost. I have an older laptop, HP Pavilion ze4400 (windows xp) and a brand new gateway (windows 7). The gateway has a built in wireless adapter. The HP came with an 802.11b cardbus thingy. I have been told that an N router is the best, but I am concerned that it will not work with the older HP. Will an N router be backwards compatible with the b? If not, can I just buy a new adapter for the HP? If so, what router and adapter should I select?

Just about every 802.11n router sold will be able to operate in a "Mixed" mode, allowing you to use your B, G or N devices simultaneously. An 802.11n router will allow you to take advantage of the improved wireless capabilities with any device that supports N. So, no need to worry about backwards compatibility.
The only thing that may be a concern (depending on how old the 802.11b adapter is) is wireless security. Chances are it supports WPA security, but if not you can fall back to WEP or the better option, buy a newer adapter.

Need help with routing a network in VMware.

I have one network with the IP of 192.168.2.10. A router is setup with two networks. The first network has an IP of 192.168.2.3 and the second network has an IP of 192.168.3.2. Then there is one final network whose IP is 192.168.3.10. My goal is to set
up route table entries and have all the networks be able to ping each other. The route table entries I am referring to is the
route -p add command. If someone could help me understand what entries I should input so all the networks can ping each other, that would be great. Thanks. If you need a picture of the network, I have a diagram.

Hi Brandon,
A diagram or picture will help us to understand your case.
For dump file or other logs which do not contain the sensitive information, you can still use OneDrive to share them so that other community members can also provide help in analysis.
If you concern personal information or company related information in logs, we recommend to send log files to our forum email account: [email protected]
Regards,
D. Wu
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Need help connecting router to router

I have a BEFW11S4 with two computers connected via wire. The BEFW11S4 is connected to a WRT300N via wire. The WRT300N has two computers (including the main) and an xbox connected by wire and others via wireless.
All items have internet access, however I cannot transfer files from the computers connected to the BEFW11S4 (running xp) to the computers connected to the WRT300N (running vista).
Not sure if I have the BEFW11S4 set up right (it auto set it up w/ Linksys EasyLink Advisor) or if this is a Windows issue.
I also cannot see the two computers connected to the BEFW11S4 from the vista computers (they are all on same workgroup), and once again, not sure if this is a windows thing or a mistake with router set up. Any help would be appreciated...I'm a bit of a newb at this stuff.

Is the WRT300N router is conected through LAN or WAN port ....
It should be connected to the LAN to LAn port on the BEFW11S4 router ....
also disable the DHCP of the router .... & change the LAN Ip - 192.168.1.2 .... then both the computers from both the routers will come in one network ....

Need help with routing - 2 ASA's in one site

Hi all,
I'm sort of a newbie to all this so sorry if im not clearly asking this the right way.
In the office, we have an ASA used as primary internet, which is on the 10.55.152.0/29 network
Im currently trying to bring up a secondary ASA for back up internet, which is on 10.55.152.8/29 network
My issue is that i cant seem to ping the inside interface of the secondary ASA for backup internet.
The core switch these connect to is a Nexus 5548.
Is there any sort of routing i need to do on the Nexus, or even on the second ASA?
Thanks!

You posted the questions 20 minutes ago? Why are you bumping it. People answer questions when they know the answer.
I tend to ignore people who expect an immediate answer.

OSPF with InterVlan Routing

Dear All,
Please help me about it ...
The same network I have designed and working fine on the RIPV2 but I want it on the OSPF but it works on the packet tracer but not on the GNS3. In this diagram there are multiple areas and there are three ABRs connected to the backbone area. The others interfaces are in the area1, area2 and area3 respectfully and in that side I need the intervlan routing.
Is it possible in the ospf the same like in the diagram ?
What type of OSPF (Point to Point or Point to Multipoint ) will be required as the R1 is the backbone router further connected with the Internet on the BGP. ?
Please sir, advise me about it.
Thanks
Best Regards
Ali Khan

Hi Jon,
Thank you very much,
1) The link between the ABRs and R1 is the wireless 1.4gig bridge link on the 5Km distand and the interface is configured with IP ospf network point-to-point.
2) On the packet tracer all the neibour displayed with its router-id, even on GNS3 but it does not show the route of other interface like area 1 or area 2.. Means the backbone router do not show the routes of other areas..(area 1 or area 2 and area 3)
3) i have tried alot and i dont think that i missed any route but the backbone area do not show the routes of subnterface (for Vlan, Router on the Stack).
Thanks
Ali

Help with simple interVlan routing on L3 switch

Hi all - I just can't get my head around this really simple interVlan routing issue. I have two VLANs (1 & 6) on a 3560 L3 switch. I simply need to route between them. Here is how I have it set up:
Firewall is the VLAN1 client's default gateway:
10.10.22.1 /255.255.255.0
3560switch config:
ip subnet-zero
ip routing
VLAN1:
(hosts on 10.10.22.x/255.255.255.0; gateway 10.10.22.1)
int vlan1
ip address 10.10.22.254 255.255.255.0
no shutdown
VLAN6: (hosts on 192.168.25.x/255.255.255.0; gateway 192.168.25.1)
ip address 192.168.25.1 255.255.255.0
no shutdown
ip classless
int gi0/31 (an available unused port)
no switchport
ip address ?.?.?.?
no shutdown
Is the issue that all my 10.10.22.x clients are going to 10.10.22.1 trying to find 192.168.25.x, when they would need to go to 10.10.22.254; then the switch should have an ip route of 0.0.0.0 0.0.0.0 10.10.22.1? Then give the router on gi0/31 the 10.10.22.254 address?
(as a side note, it would be easier for me to change the gateway's IP than to change each VLAN1 client's IP.)
Thanks for any help!

Hi all - I just can't get my head
around this really simple interVlan routing issue. I have two VLANs (1
& 6) on a 3560 L3 switch. I simply need to route between them.
Here is how I have it set up:Firewall is the VLAN1 client's default gateway:
10.10.22.1 /255.255.255.03560switch config:
ip subnet-zero
ip routingVLAN1:
(hosts on 10.10.22.x/255.255.255.0; gateway 10.10.22.1)
int vlan1
ip address 10.10.22.254 255.255.255.0
no shutdownVLAN6: (hosts on 192.168.25.x/255.255.255.0; gateway 192.168.25.1)
ip address 192.168.25.1 255.255.255.0
no shutdownip classlessint gi0/31 (an available unused port)
no switchport
ip address ?.?.?.?
no shutdown***Is
the issue that all my 10.10.22.x clients are going to 10.10.22.1 trying
to find 192.168.25.x, when they would need to go to 10.10.22.254; then
the switch should have an ip route of 0.0.0.0 0.0.0.0 10.10.22.1? Then
give the router on gi0/31 the 10.10.22.254 address?(as a side note, it would be easier for me to change the gateway's IP than to change each VLAN1 client's IP.)Thanks for any help!
Hi,
With the above configuuration vlan 1 users will be going to firewll and if they want to reach vlan 6 firewall should have rule to permit for vlan 6 subnet and route towards vlan 6 interface and which is not there is your network.
Just clarify few things you want firewall to come into picture for every traffic which goes between vlan or not and in interface gi0/31 you will be connecting router also is this router is sending traffic to outside world if yes then you need to change some design configuration to route tha traffic from vlans to outside world.
If you want only inter vlan routing between vlan 1 and vlan 6 via firewall then make another zone in firewall and place that in vlan 6 with ip address as given in vlan 1 so that vlan 6 users can point traffic towards vlan 6 interface of firewall and in firewall just permit the vlan 6 communication with vlan 1 and drop a route for vlan 6 towards switch vlan 6 interface.
and if between vlans you dont want firewall to come into picture then the best is create three vlan one for vlan 1,vlan 6 and outside vlan between router and firewall and drop a default route towards firewall.In this case inter vlan routing will be taken care by switch and traffic towards outside world will scaaned as per rule given in firewall.
Hope to help
If helpful do rate the post
Ganesh.H

Need help on which router to buy for my BB 8320

Now i know 8320 is dated but at this point i am not planning to change anytime soon .
So I have a router which is kinda old, it didnt really occur to me since it worked. When i got my bb 8320 i was in a hotel and i could connect through their wireless without any hassle. I could surf, use youtube, name it.
When i got home i couldnt do anything, i spent countless nights trying to figure out waht was wrong then i realized its my router. If only BB said somethign it wont support old routers then i wouldve saved myself hours of self-loathing.
Anyways I also have gone to my friends house, and i could connect to her linksys router without any hassle. i was the one who set her router up and we bought it this year. i didnt do anything special, configuration-wise or w/e.
So NOW i am just going to buy a new router. I really need help!!!!
I was wondering if this one is good:
W311R Wireless-N Broadband Router
W311R integrates the wireless AP, router, four-port switch and firewall in one, and increases over 4 times transmission range of ordinary 802.11g products. Compatible with IEEE802.11n (Draft 2.0) and IEEE802.11g/b standards, it can provide up to 150Mbps stable transmission rate. It is dedicated to SOHOs and students’ dormitory. In addition, URL and MAC address filtering can take it easy for parents and network administrator to manage network life, and QoS bandwidth control over specific computer’s downloading speed is supported as well. Moreover, UPnP and WMM support can smooth your MSN voice better, and the included Setup Wizard on CD-ROM will be easy and fast for non-savvy users to install the device and access to the Internet.
Overview:
* Includes router, wireless access point, four-port switch and firewall in one
* Provides up to 150Mbps uploading and downloading speed
* Supports two WPS (Wi-Fi Protected Setup) encryption methods: PBC and PIN
* Compliant to IEEE802.11n, IEEE802.11g, IEEE802.11b, IEEE802.3 and IEEE802.3u standards
* Supports far-distance transmission, 100 meters indoor, 400 meters outdoor (depends on the environments around)
* Supports 64/128-bit WEP encryption, WPA and the latest WPA2 encryption security authentication
* Supports RTS/CTS protocol and data partitioning function
* Provides one 10/100Mbps Auto-Negotiation Ethernet WAN ports for WAN connection
* Provides four 10/100Mbps Auto-Negotiation Ethernet LAN ports for LAN connections
* Supports xDSL/Cable MODEM, static and dynamic IP in community networking
* Supports remote/local Web management
* Supports WMM to better smooth your voice and video
* Supports SSID stealth mode and access control based over MAC address (up to 30 entries)
* Supports Auto MDI/MDIX
* Supports wireless Roaming technology and ensures high-efficient wireless connections
* Supports auto negotiation/manual mode for 802.11b/802.11g/802.11n
* Supports UPnP and DDNS
* Supports Firefox 1.0, IE5.5 or above
* Supports SNTP
* Supports virtual server, DMZ host
* Built-in firewall for hacker’s attack prevention
* Supports DHCP server/client
* Supports auto wireless channel selection
* Supports the control over LAN access to Internet
* Provides syslog to record the status of the router
* Supports WDS wireless network extension
* Supports QoS function
Input Voltage Range
AC 110~240V
Output Voltage Range
9V~1000mA
Consumption
20dbm
Operating Temperature
0? ~ 40?
Storage Temperature
-40? ~ 70?
Operating Humidity
10% ~ 90% RH non-condensing
Storage Humidity
5% ~ 90% RH non-condensing
Antenna
One Non-detachable external antenna (5dBi)
Frequency Range
2.4GHz-2.5GHz
EVM
-30dB
Sensitivity
54M:-74dBm@10% PER; 11M:-85dBm@8% PER; 6M:-88dBm@10% PER; 1M:-90dBm@8% PER
Outdoor
400m
Indoor
100m
WLAN?LAN
93Mbps
WLAN?WLAN
93Mbps
Frequency Range
2.4GHz
Gain
5dBi
Nominal Impedance
50
Polarization
Linear; Vertical
Maximum Power
1W
* Vertical Beamwidth 360º

Flip UltraHD.
Shoots mp4 H264 format files. Fits in a shirt pocket and records 2 hrs worth of material to an internal card. Charges from your USB port as you download. If you are just trimming clips, you can use QT Pro without conversion. If you need to edit, convert to ProRes 720p30. Works like a dream.
Just make sure you have it solidly placed when you pull the trigger as there is no image stabilization.
Oh, and it is only $199 US.
x

Router's Web-based page not loaded correctly.. Need Help!!

I'm using WRT54G v2.2 router and recently i noticed tat i've flashed a wrong firmware which is WRT54GL version, so wat i did was i flash the original v2.2 firmware which i noticed it had not been updated since 2007... after i flashed the router and i log into the 192.168.1.1 webpage.. all the tabs and many options are missing as though the page was not loaded correctly or fully loaded and i cant even get into the management page and so on..
I really need help on this..

Hold the reset button down for 30seconds and then release it. Unplug the power cable for 10 seconds. try accessing the set up page once again and see if it makes a difference.

Need help accessing the router web page. I have been tol...

Need help accessing the router web page. I have been told my router is acting like a switch and the IP address is not in the proper range. I have tried reseting the router (hold for 30 sec and unplug for 5 mins). Didn't work.
thanks

What router are you using? Almost all Linksys routers use 192.168.1.1 as the default local IP address, but there is at least one that uses 192.168.16.1 , namely the WTR54GS (not the WRT54GS).
You need to try again to reset the router to factory defaults.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank (note: a few Linksys routers have a default user name of "admin" (with no quotes)), and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you.
Message Edited by toomanydonuts on 01-21-2008 04:40 AM

Need help Setting up Multiple Static Ip , 1 for each port of the fios router

Need help Setting up multiple Static Ip on my fios router
I have been trying to figure out how to set up multiple ip in my fios router.
However I kind of managed how to set up multiple static ip However the way I want it is for each port of my router to have an external ip signed to it. ( like 4 different modem in 1 )
Verizon gave me 5 static ip but they can not help me how to set it up.
Have anyone here done more then one static ip on different ports? I assume that the process will be the after the second static ip.

You want to set up Static Nat. You will not assign the IP to a port, but rather to a local machine. Figure out what machines you want your IP's to go to. Under the firewall section you will see static nat. Pick the machine you want and enter one of the IP's you were assigned.

HT4199 I need help connecting to my WIFI. I purchased a new router and am having trouble connecting.

I need help connecting to my WiFi. I purchased a new router and am having trouble connecting.

your gonna want to contact your internet service provider for the best info on setting that router up. but for connecting to wifi on the iphone, ipad, and ipod
go to
settings > wifi
then choose your connection and enter the password

Need help connecting to ISP through DSL/router

Hi
I need help configuring my intel solaris8 box to get to the internet. I have dsl going into a linksys router. my windows machine have no problem using the DNS servers from pacbell. i also have DNS setup on my novell server, but the solaris8 box still can't resolve anything. I can ping everyone on my segement, I can connect to my novell web server netscape navigator but can't resolve it's name, i have to use it's ip address. I can remote logon. I lloked for a resolv.conf file but can't find one, help!!!!
Danny

Edit /etc/resolv.conf (it may not exist) with the following lines:
domain your.domain.name
nameserver your.primary.dns.ip
nameserver your.secondary.dns.ip
search your.domain.suffix
The last line is optional, but please do substitute those values for the ones that you use.
As far as a default route goes, just edit /etc/defaultrouter (may not exist) and put the ip of your default gw on a single line.
Alex

I need help moving my Photoshop 7 from my old laptop to my new laptop which is running Windows 7 Enterprise. I've tried two routes unsuccessfully. I install the CD, it does not autoplay. I execute Autoplay.exe at the root directory, I am welcomed, I ch

I need help moving my Photoshop 7 from my old laptop to my new laptop which is running Windows 7 Enterprise. I’ve tried two routes unsuccessfully. I install the CD, it does not autoplay. I execute Autoplay.exe at the root directory, I am welcomed, I choose English, I accept the EULA, I get the Install/Explore choices window, with the Install button already selected, I click the Photoshop button, the CD spins, and nothing happens. In the 2nd attempt I execute Setup.exe in the Photoshop directory, and nothing happens at all. I’m never even offered the opportunity to enter my product code. What should I do?

There could is likely a compatibility problem between the old software and the newer operating system.

Need help InterVlan Routing on SF300-24P? .

Similar Messages

Maybe you are looking for