Need help on complex configuration
hi all,
i share internet access with my neighbour. in order to do it i bought two airport express base station and configured them using wds.
the main station is installed in my neighbour apartment; the remote station is installed in my apartment and is also connected to my hi-fi (airtune is a fundamental feature i simply can't do without). a laser printer is also connected to the usb port of the remote station.
everything is working fine, but now i would like to do more. i would like to buy a time capsule and connect it to my existing wireless network.
time capsule does not have the airtune feature so i cannot just substitute my existing remote base station.
unfortunatly airport express does not support the 802.11n standard. so, as far as i know, if i add a time capsule unit to my existing wireless network, it will operate in 802.11g mode thus being unusable for network backups (using time machine) or for adding an additional airdisk (network share) to the available usb port.
before spending money on a time capsule, i need to solve this problem. here is my idea:
1) internet router is connected to the main airport express using ethernet
2) the main airport express announces my wireless network and act as the main wds station
3) the second airport express is configured in relay mode and synchronize with the main station using wds. the second airport station drives a laser printer through the usb port (bonjour protocol). it is also connected to the hi-fi system (airtune). important: since it operates using the 802.11g standard, the second airport express will not be used as an access point. it should only replicate the signal from the main (using wds) to the time capsule (using ethernet), drive the laser printer and send music to my amplifier
4) the time capsule is configured as a remote base station and synchronize with the second airport using ethernet. it is used as an access point and operates using the 802.11n standard. it also provide network backup services and share another disk through the usb port
5) my macbook pro access the wireless network through the time capsule unit and operate using the 802.11n standard
this solution sounds good to me, but there are a couple of things that i'm not sure can be done.
1) how can i configure the time capsule in order to operate as a remote base station synchronizing with the relay using the ethernet port?
2) how can i avoid that my powerbook while accessing my wireless network does connect through the relay station instead of using the time capsule? (in other words how can i configure the relay station so that it does not operate as an access point?)
any suggestion or comment will be highly appreciated....
thank you very much in advance
Duane wrote:
doctormirabilis, Welcome to the discussion area!
1) how can i configure the time capsule in order to operate as a remote base station synchronizing with the relay using the ethernet port?
Configure the Time Capsule to act as a bridge (not distributing IP addresses). Also configure the Time Capsule to create an 802.11n wireless network with a unique network name (SSID). That's it.
2) how can i avoid that my powerbook while accessing my wireless network does connect through the relay station instead of using the time capsule?
Configure the Time Capsule to use a different network name than the WDS link between the 2 AirPort Express (AX). Configure the PowerBook to use the Time Capsule network.
There are 2 pieces of information that you should be aware of...
(1) None of the PowerBooks are capable of 802.11n.
(2) The WDS link cuts your available bandwidth in half. So the wireless link to your neighbor's has a maximum potential of 27 Mbps.
Let's for a minute assume that you have a Mac compatible with 802.11n. In your configuration the time you could take advantage of the 802.11n speed is when the Mac is sending/recieving data directly from/to the Time Capsule.
There would be NO speed increase in Internet access. The speed of Internet access is going to be controlled by the slowest link in the path to the Internet. That is probably the connection to the ISP. The next slowest path is the WDS link to your neighbor's.
Duane,
I am in a similar situation, sharing internet with my neighbor. Do you think it would be plausible to hook up a vonage phone adapter to time capsule's ethernet port if time capsule is bridging from my neighbor's router in the configuration you have described? A check of my upload speed shows 1.67Mbps (powerbookG4 w/ airport extreme). Vonage reccommends 90kbps minimum upload speed. Am I going to lose some speed putting the Vonag adapter behind time capsule?
Thank you
Similar Messages
-
Need help on struts configuration with ColdFusion 10 using IIS
We need help on struts configuration with ColdFusion 10 using IIS.
Earlier we were using ColdFusion 8 with IIS 6 for one of our application. This application internally calls struts. After upgrading to ColdFusion 10 struts calls are not loading. We get 404 error.
In ColdFusion 8 struts were configured using actions extension .do in IIS from this file-
C:\ColdFusion8\runtime\lib\wsconfig\jrun_iis6.dll.
But in ColdFusion 10 this file is not present as ColdFusion 10 uses Tomcat in place of Jrun.
Also there is no information in ColdFusion log file.Duane wrote:
doctormirabilis, Welcome to the discussion area!
1) how can i configure the time capsule in order to operate as a remote base station synchronizing with the relay using the ethernet port?
Configure the Time Capsule to act as a bridge (not distributing IP addresses). Also configure the Time Capsule to create an 802.11n wireless network with a unique network name (SSID). That's it.
2) how can i avoid that my powerbook while accessing my wireless network does connect through the relay station instead of using the time capsule?
Configure the Time Capsule to use a different network name than the WDS link between the 2 AirPort Express (AX). Configure the PowerBook to use the Time Capsule network.
There are 2 pieces of information that you should be aware of...
(1) None of the PowerBooks are capable of 802.11n.
(2) The WDS link cuts your available bandwidth in half. So the wireless link to your neighbor's has a maximum potential of 27 Mbps.
Let's for a minute assume that you have a Mac compatible with 802.11n. In your configuration the time you could take advantage of the 802.11n speed is when the Mac is sending/recieving data directly from/to the Time Capsule.
There would be NO speed increase in Internet access. The speed of Internet access is going to be controlled by the slowest link in the path to the Internet. That is probably the connection to the ISP. The next slowest path is the WDS link to your neighbor's.
Duane,
I am in a similar situation, sharing internet with my neighbor. Do you think it would be plausible to hook up a vonage phone adapter to time capsule's ethernet port if time capsule is bridging from my neighbor's router in the configuration you have described? A check of my upload speed shows 1.67Mbps (powerbookG4 w/ airport extreme). Vonage reccommends 90kbps minimum upload speed. Am I going to lose some speed putting the Vonag adapter behind time capsule?
Thank you -
Need Help W/ Raid Configuration
I NEED HELP W/ MY RAID CONFIGURATION.
I HAVE THE K7N2 DELTA-ILSR MOBO W/ A XP2600+, I HAVE TWO 40 GIG HARDDRIVES THAT I WANT TO RAID 0 TOGHTER.
I HAVEN'T FOUND IN THE MANUALL HOW TO SET UP THE RAID ARREY, I DONT NO HOW TO SET THE DRIVER AS FAR AS SLAVE/MASTER SETTINGS, WITCH ONE NEEDS TO GO TO WITCH CHANNEL ( PRIMARY/SECONDARY/CS).
- EVERY TIME THAT I SET IT UP THE ARREY IS SHOWING ONLY 1 DRIVE, I BELIVE THAT RAID 0 SHOULD HAVE BOTH OF THE DRIVES AS 1 BIG DRIVE, CAN SOME ONE HELP ME W/ INSTARUCTIONS HOW TO CREATE THIS ARREY?
thanks guysI had RAID 0 set on my system. I used the MSI Live Update software to update my RAID controller because it said it needed it. It hung up in the middle of the update, so I let it sit for 24 hours. Finally I rebooted, & now it won't even see the drives. If you go with RAID 0, back up your data, and keep it backed up!!! I will say this, while it worked, it was really really fast!!! In order to make my RAID work (while it lasted) I used two SATA drives. I believe you can also use one ATA & 1 SATA instead of two SATA drives. If you use 1 ATA drive, set it to master & connect to IDE 3. This will be the only drive on that cable. During the boot up, you have to follow the prompt & press to enter the FastBuild (tm) Utility. Once there, you can choose Auto Setup & it will do the work for you. I must re-iterate, KEEP YOUR DATA BACKED UP!!!!!! I hope this helps. Good luck!
K7N2G-ISLR, AMD 2600+, Twin rapter 37gb hard drives, 1gb DDR-400, G-Force FX
5600 256mb AGP etc. -
NEED HELP WITH WORKFLOW CONFIGURATION
I need help with 3 situations below. Please help me with these. How do I configure these. I also haveto provide specs to the Abaper. What exactly do I need to include in the specs. I anyone has the specs similar to these please send me over. Also tell me what I need to do to get these requirements fulfilled.
1) Description:
This is a workflow requirement to serve as a reminder of upcoming investment
maturities.
Requirements Details:
Create a workflow to serve as a reminder of upcoming investment maturities.
Donor System Processing Narrative:
Read the maturity dates on investments.
Target System Processing Narrative:
Send a notice to the parties that an investment will be maturing soon.
2) Description:
Implement workflow to route invoice receipts using a one time vendor for management
review and posting
Desired Functionality:
If a one time vendor is entered by the AP Voucher Clerk the invoice will be automatically
parked by the program and a workflow notification triggered to the Accounting
Supervisor and Accounting Manager (backup). The Accounting Supervisor will review
the parked document and imaged copy of the actual invoice and post the parked
document.
3) Description:
An approval workflow is needed for credit memos posted to SAP customer accounts.
Desired Functionality:
The Cash Journal Clerk will post a credit memo to the customer account using transaction
FV75 Park Customer Invoice. This transaction will automatically trigger a workflow to
the Accounting Manager for approval and then to the CFO who will approve and post the
parked document. (In order for this transaction to automatically trigger what configuration needs to be done).Bob;
You can borrow the example code that ships with both NI-DAQ (in case you are doing NI-DAQ function calls) and Labview. The best examples to start with are the ones that have the prefix STC.
Hope this helps.
Filipe A.
Applications Engineer
National Instruments -
Need help on variant configuration
Hi Guru,
Here we need to use variant configuration.But i am new in variant configuration.Can somebody tell me the different steps of variant configuration from PP side.I have gone through standard document. But still i need this information. The Industry in which I am going to implement this,is producing Colored, profiled sheet to provide roofing solution.The metal roofing sheet can have different profile, different colour, different thickness, different width and so on.They have nearly three thousand of different combination.
Please respond.
Regards
RajibHi,
Pls. find herewith Variant Configuration Procedure steps as below
VARIANT CONFIGURATION:
1.Create a Material - KMAT type with Item category (002)
2.Create Charateristics in CT04 - Zbike, where in values mention the Color of the bile like Red, Blue etc
Create another characteristics in CT04 - ZPrice, where directly go the additional data tab and maintain the table SDCOM and field VKOND (ABAP Dictionary it will ask for).
3.Assign these two characteristics to a Class in CL01 - ZBikeclass ( Type 300) in characteristics tab page.
4Then go to CU41 Configuration profile select the material and enter the description click on the class assignment ie assign Zbikclass.
5Now go back to CT04 - enter Zbike -go to values- select Red- go to extras - Other Dependencies - Select Procedure enter in front 10 write - $self.ZPrice='Red' and save.
6.Now go back go to extras - Other Dependencies - assignments and assign relationship ( by default it will come just save).
7.Now select Blue- go to extras - Other Dependencies - Editor - Select Procedure enter in front of 10 write - $self.ZPrice='Blue' and save.
8.Now go back go to extras - Other Dependencies - assignments and assign relationship ( by default it will come just save).
9.Now go to VK11 - Enter VA00 (Condition)(For Std RVA001 Pricing Procedure) - enter variant Red and Blue give the rates accordingly and create the sales order.
Variant Configuration: Complete Maintenance:
Technical name: SAP_LO_VC_MAINTAIN
Tasks
The variant configuration processor sets up the rules for multi-variant products and maintains them in the database. He or she simulates and executes the configuration. This role is required wherever variant configuration is used.
The complete model also contains sales order processing (VA01/VA02), and the connection to SCE/Internet Sales and Mobile Sales.
Activities in Variant Configuration;
Transaction
Activity
CC04
Display product structure
CWBPP
Engineering Workbench
Variant Configuration
VA01
Create sales order
VA02
Change sales order
VA03
Display sales order
CU51
Maintain configurable order BOM (multilevel)
CU52
Maintain configurable order BOM (single level)
CU50
Configuration simulation
CU80
Reporting functions for characteristics and values
Configured Objects
CU44
Material
CU45
Standard network
Assignment of Configured Materials
CS40
Create assignment for configured material
CS41
Change assignment for configured material
CS42
Display assignment for configured material
Configuration Profile
CU41
Create configuration profile
CU42
Change configuration profile
CU43
Display configuration profile
Dependencies: Single Dependency
CU01
Create single dependency
CU02
Change single dependency
CU03
Display single dependency
Dependencies: Dependency Net
CU21
Create dependency net
CU22
Change dependency net
CU23
Display dependency net
Dependencies: General
CU05
Dependency where-used list
CU04
Dependency list
Tools: Variant Function
CU65
Create function
CU66
Change function
CU67
Display function
CU68
List functions
Variant Table Structure
CU61
Create variant table
CU62
Change variant table
CU63
Display variant table
CU64
List variant tables
Variant Table Contents
CU60
Maintain variant table contents
CU59
Transfer variant table contents to database table
Knowledge Base for SCE: Knowledge-Base Object
CU31
Create knowledge-base object
CU32
Change knowledge-base object
CU33
Display knowledge-base object
Runtime Version
CU34
Create runtime version
CU35
Change runtime version
CU36
Display/export runtime version
CU37
Create SCE database schema on PC
For complete details of Variant Configuration go to the following link :
http://help.sap.com/erp2005_ehp_03/helpdata/EN/96/468f38721f9977e10000009b38f842/frameset.htm
Hope this helps.
Regards,
Prakash -
Need help with complex column creation command
Hello, all
I need help with a complex column creation command and SQL anywhere help is not sufficient for it.
Here is the situation:
I need to write a generic DDL "alter table" command, which can add/modify columns without knowing in advance if they already exist in the destination table.
Is there a command, which looks like:
alter table "table1" add (on existing modify) column1 <datatype> <default> ?
Thank you,
ArcadyHi.
I don't think this is supported in alter table command. But you can code that inside an if statement which queries systables & syscolumns. Your code should be something like that:
if (select count(*) from sysobjects, syscolumns where sysobjects.id = syscolumns.id and sysobjects.name = 'some_table' and syscolumns.name = 'some_column') < 1
begin
alter table some_table add some_column numeric(12) not null
end
This is an example..
Andreas. -
Need Help with complex query and computing values
I have an issue trying to combine data from several tables. I need help trying to compute the "Total Hours", "Max Pressure" ,"Average Pressure" while displaying the "Manufacturer",
"Part Type" , "Serial Number", "District", "Status","Truck Type",and "truck number" for a certain Part on all Trucks. I need to be able check and see if the serial number was on
a particular job and calculate the hours of that serial number if it was on that job and the jobdate falls between the install date and removal date. Ive tried but keep getting either
repeating rows, total hrs of the truck instead of the serial number. Ive considered doing a pivot to display it but have been having trouble putting it together.
table 1
(*records of parts*)
Contains serial number,truck number, part type, part number, install date, removal date, status
table 2
(*records of Jobs*)
contains Jobnumber, JobStartdate, Max pressure, average pressure, and Totalhrs
table 3
(records related to jobs and trucks)
contains jobnumber, district , and truck numbers
Table 4
(records of manufacturers and part numbers)
contains partnumber, manufacturer name, and truck type
I would like to get it to show like below
SerialNo PrtType
MFG TruckNo
TrkType TtlHrs
MaxPr AvgPr
Status
Dst
AB345 1200series
NGK 2G34
Boss X 400 10,000
9500 NonOp
NE
Thanks in advanceHope this helps
Note: (Date of Mar 1 2014 was just extended to a further date so the system would know that its still operating when calculating current hours)
Table 1
SerialNo TruckNo InstallDate RemovalDate Status PartNo PartType
BJ1002 F917 2013-09-17 2014-03-01 Oper L871235 BJ 3000 GL
CWS1002 F104 2012-11-21 2013-03-29 NonOper L76088-450 CWS 2000
CWS1003 F104 2013-04-24 2013-08-01 NonOper L76088-450 CWS 2000
CWS1005 F187 2012-11-21 2013-04-04 NonOper L76088-450 CWS 2000
CWS1006 F187 2013-04-24 2013-06-30 NonOper L76088-450 CWS 2000
CWS1007 F187 2013-06-30 2013-03-01 Oper L76088-450 CWS 2000
CWS1009 2F60 2013-05-05 2013-03-01 Oper L76088-450 CWS 2000
CWS1011 F809 2013-05-28 2013-08-28 NonOper L76088-400 CWS 2000
CWS1013 F990 2013-06-11 2013-10-29 NonOper L76088-450 CWS 2000
CWS1015 F783 2013-06-28 2013-03-01 Oper L76088-450 CWS 2000
Table 2
JobNumber Date District PrAvTreat PrMaxTr TotalHrs
553811287 2012-01-19 Fairmount 7337 8319 1.53
652110088 2012-08-20 San Antonio 6340 7075 0.47
652110090 2012-08-21 San Antonio 6134 7131 0.62
652110091 2012-08-22 San Antonio 6180 2950 0.58
652110092 2012-08-23 San Antonio 5959 6789 0.64
652110093 2012-08-23 San Antonio 6165 7466 0.62
Table 3
TruckNo District JobNumber
1F01 Odessa 10011012329
1F01 Odessa 10011012333
1F01 Odessa 10011014831
1F01 Odessa 10011014834
1F01 Odessa 10011012332
1F01 Odessa 10011012328
1F01 Odessa 10011014829
Table 4
PartNumber Manufacturer TruckType
L322020-2 Jimmy Dean Ford T
L322738-2 Lucas Ford T
L47869-1 Jimmy Dean Ford T
L76070-650 NGK Ford T
Sam Howard -
Need help with AS8 configuration
Our present situation is like this:
AS7 with single domain and multiple server instances
instance A running on port xxx containing app1
instance B running on port yyy containing app2
instance C running on port zzz containing app3
Now, when I move to AS8.1 PE, I dont see the option to create a server instance inside a domain. I need to create 3 domains in order to accomplish the same task as above. Not only that, now I need to login to 3 different admin servers to manage the 3 apps on 3 ports
I need help with some options I can use
thanksI'm not sure but i think that on 8.1 pe you can have only one server instance by default...
But you can olso try by command line tool asadminin [installdir soas]/binuse:
asadmin --help for a list of commands available.
In the list should be create-instance to create a stand alone instance.
Hi
Stefano -
Need help regarding complex calculation using Max value and limiting data after Max date in MDX
I am working on a bit complex calculated measure in SSAS cube script mode.
Scenario /Data Set
Date
A
B
C
A+B
5/29/2014
Null
34
Null
34
6/30/2014
Null
23
45
68
7/15/2014
25
-25
Null
0
8/20/2014
-34
Null
Null
-34
9/30/2014
25
Null
60
25
10/15/2014
45
-45
Null
0
11/20/2014
7
8
Null
15
a) Need to capture latest non-null value of Column C based on date
with above example it should be 60 as of 9/30/2014
b) Need to capture column A+B for all dates.
c) Add values from column (A+B) only after latest date which is after 9/30/2014.
with above example it's last 2 rows and sum is 15
d) Finally add value from step a and step c. which means the calc measure value should be = 75
I need to perform all this logic in MDX. I was able to successfully get step a and b in separate calc measure, however i am not sure how to limit the scope based on certain date criteria. In this case it's, date> Max date(9/30/2014) . Also how should
i add calculated members and regular members?
I was able to get max value of C based on date and max date to limit the scope.
CREATE MEMBER CURRENTCUBE.[Measures].[LatestC] AS
TAIL(
NONEMPTY(
[Date].[Date].CHILDREN*[Measures].[C]),1).ITEM(0) ,visible=1;
CREATE MEMBER CURRENTCUBE.[Measures].[MaxDateofC] AS
TAIL(
NONEMPTY(
[Date].[Date].CHILDREN,[Measures].[C]),1).ITEM(0).MemberValue ,visible=1;
Please help with Scope statement to limit the aggregation of A+B for dates > MaxDateofC? Also further how to add this aggregation value to LatestC calc measure?
Thank YouHi Peddi,
I gave TRUNC to both of the dates. But still the same issue. I think the problem is in returning the BolbDomain.
return blobDomain;
} catch (XDOException xdoe) {
System.out.println("Exception in XDO :");
throw new OAException("Exception in XDO : "+xdoe.getMessage());
catch (SQLException sqle) {
System.out.println("Exception in SQL :");
throw new OAException("SQL Exception : "+sqle.getMessage());
catch (OAException e) {
System.out.println("Exception in OA :");
throw new OAException("Unexpected Error :: " +e.getMessage());
Thanks and Regards,
Myvizhi -
Large processing in ADF BC 10.1.3.4 - need help on AM configuration
I working in Jdeveloper 10.1.3.4 and ADF BC. I have some large processing and processing is getting slower over the time. For example:
I procces tens of thounsend records over ADF BC. I get one record, do some preocessing, update that record and create new one. At begin speed is 100 records per seconds, but it slowing and on 10000 record is 10 records per second. Xms param is set to 1024M and AM configuration is not changed. Do you have some advice? Do I need some adjustments of AM configuration? Any help?
Also I’m working on some billing system and I have similar problem. I start processing in separate thread and that work corectly, but after some time (say 1 hour and ten thousend custumers) I catch error say ‘invalid operation with view object’. I catch that error, but can’t continue proccesing. I guess that is also some problem with resources. If anyone have similar problems, please HELP :)Dragan,
If you are talking about iterating over VO records - have a look at the VO tuning parameters, especially if you are using range paging mode. In range paging mode, the performance of getting the next set of rows degrades as you proceed through the result set.
John -
Need help with AAA configuration
I am trying to configure AAA on my network devices. I am using TACACS+ with an ACS (3.2) server. I have setup two user groups in the ACS server, one with enable priviledges and one without. I am able to get the AAA configuration to work when telnetting into the devices. However, when logging into the console port, the user group with enable priviledges do not go directly into enable mode as the telnetted users do. How to fix this?
Hi,
You will need to use the following command :-
aaa authorization console
This command will not show up on the help.
Regards,
Vivek -
Need help with 6300 configuration settings
I can't get sms, email or web to work on my lovely new 6300 phone (an xmas present from my daughter) :-(
I travel between England and France and have an Orange sim card for England and an SFR card and contract in France (Orange doesnt work in the mountains).
I managed to text when in England with the orange card. On arriving in France I found the phone was locked to Orange (first headache, given that I live in the country, over 50 miles from any Nokia dealer). I got the phone unlocked, but SMS etc were still not working and local mobile outlets hadnt a clue. So I'm on my own.
Rummaging around this site I realised I probably needed to additional settings, and downloaded these.
Now for the real nightmare: how the hell to set these configuration settings. I seem to be going round in circles. Is there anybody out there who could help me make some sense of the following settings???!!!
Although helpful, this site is not good at explaining the significance of the following (and whats more I feel they should probably be listed in the reverse order?)
- default config setting
- preferred access point
- personal config setting
DEFAULT CONFIG SETTING
I have a choice of
- orange (inherited with branded phone and presumably needed when back in the UK?)
- personal config
- SFR MMS (downloaded by me from Nokia)
- Wanadoo (downloaded by me from Nokia)
Ive chosen personal config (see below)
ACTIVATE DEFAULT IN ALL APPS
I have said no ??
PREFERRED ACCESS POINT
Ive created one called 'Fra access point' (see next) so as to have alternative to all the orange ones,
PERSONAL CONFIG SETTING
I've made three: FRA access point, FRA mailbox and Fra web
The access point has data bearer as Packet data (dont ask me what this means!) and I made up my own user name and password
Well, there you are. I would at least like to have the sms working (I suspect the email may be another hurdle as my pop and sms servers are different).
I do hope someone can help meI was disappointed by the deafening silence which followed my cry for help - perhaps a bit too meaty for a Friday afternoon?
Anyhow, amazingly, after a loooong and expensive phone call to SFR (Vodaphone) the problem has been resolved (sort of).
I had been fiddling around with the configurations under Settings. It turned out there are MORE settings under Message settings and these included the need to specify a number for the Message Centre. (Nowhere on the SFR site is this number given, plus their link for downloading configurations is not working...)
Be warned, I might be back in a week or two when I have more energy to tackle email. -
Need Help on Firewall Configuration
Hi,
I am facing few problems with my current external ip address configured on my outside interface of ASA 5520. Due to some reason when I am trying my external ip for e.g. x.x.x.12 I am not able to access few websites but my VPN's are woking fine. But when I change it to x.x.x.14 my VPN connection offcourse goes down but I am able to access all sites which were not accessible by using that ip. Please help me out, as I am running short of Interfaces whatever I have to do is on the same interface. I want x.x.x.12 for VPN connection and x.x.x.14 for Internet access. Can someone please help me in achieving the same.
Thanking you.
Regards,
Mangesh Kamble.
CCIE R&SYou need to do something like this:-
interface outside
ip address x.x.x.12
global (outside) 1 x.x.x.14
nat (inside) 1 x.x.x.x y.y.y.y
x.x.x.x = inside IP subnet
y.y.y.y = subnet mask
the above will:-
1) Allow any remote VPN configured to connect on the .12 will now work
2) Any traffic from the inside will be natt'd to x.x.x.14 on onto the internet.
if you have internal services that are currently available from the internet via the .14 address - I suggest the below:-
static (inside,outside) z.z.z.z x.x.x.14 netmask w.w.w.w
z.z.z.z = interna server IP address
w.w.w.w = mask
The write the acl accordingly:0-
access-list danger-in extended permit tcp any host x.x.x.14 eq 80
access-list danger-in extended permit tcp any host x.x.x.14 eq 443
access-list danger-in extended permit tcp any host x.x.x.14 eq 25
or whatever
HTH> -
Need help on complex math calculation in labview
I need some help by being pointed in the right direction. I have a piece of old lab equipment that I will be connecting to labview. In order to send commands to the hardware, I have to calculate a checksum. The checksum algorythm requires me to take alphanumeric characters, convert them to binary, perform binary addition, perform an Xor, mask certain digits, and convert the resultant binary string back to an ascii character. Does labview have the capabilities to do this on it's own, or should I look at connecting to something like an external dll?
I have Visual Studio 2008 and some previous VB experience, so I think I could write a program that would do the calculation, but don't really know exactly what type of project (dll, etc.) is best. Are there any specific settings for the dll so that labview can use it. I see an example for C++ for Visual Studio 2005, but that is as close as I can get. I only know VB, not C# or C++
Can someone please point me in the right direction?
Tron
Solved!
Go to Solution.You basically need some logical shifts and ANDs.
Check version 2.
/Y
LabVIEW 8.2 - 2014
"Only dead fish swim downstream" - "My life for Kudos!" - "Dumb people repeat old mistakes - smart ones create new ones."
G# - Free award winning reference based OOP for LV
Attachments:
Checksum ver 2.vi 10 KB -
Need Help with complex query for productio database
Hello again,
i need your help again, for an query how Shows me how long every production step takes per Order.
See sample data and what i expect.
Thank you all for your help.
We use Oracle Database 11g Enterprise Edition Release 11.2.0.3.0 - 64bit Production
Here the sample data tables:
CREATE TABLE TABLE_2
( "ORDER_NR" VARCHAR2 (12)
, "PRIORITY" VARCHAR2 (2)
, "WO_STEP" VARCHAR2 (1)
, "STEP_DATE" DATE
CREATE TABLE TABLE_1
( "ORDER_NR" VARCHAR2 (12) PRIMARY KEY
, "PRIORITY" VARCHAR2 (2)
, "CREATE_DATE" DATE
, "ACT_STEP" VARCHAR2 (2)
, "STEP_DATE" DATE
, "EMPLOYEE" VARCHAR2 (5)
, "DESCRIPTION" VARCHAR2 (20)
INSERT INTO TABLE_1 (ORDER_NR, PRIORITY, CREATE_DATE, ACT_STEP, STEP_DATE, EMPLOYEE, DESCRIPTION)
VALUES ('1KKA1T205634', '12', TO_DATE('10-FEB-13 10:00:00','DD-MON-RR HH24:MI:SS'), 'U', TO_DATE('28-FEB-13 12:00:00','DD-MON-RR HH24:MI:SS'), 'W0010', 'CLEAN HOUSE');
INSERT INTO TABLE_1 (ORDER_NR, PRIORITY, CREATE_DATE, ACT_STEP, STEP_DATE, EMPLOYEE, DESCRIPTION)
VALUES ('1KKA1Z300612', '12', TO_DATE('08-FEB-13 14:00:00','DD-MON-RR HH24:MI:SS'), 'F', TO_DATE('20-FEB-13 16:00:00','DD-MON-RR HH24:MI:SS'), 'K0052', 'REPAIR CAR');
INSERT INTO TABLE_2 (ORDER_NR, PRIORITY, WO_STEP, STEP_DATE)
VALUES ('1KKA1T205634', '12', 'A', TO_DATE('12-FEB-13 13:00:00','DD-MON-RR HH24:MI:SS'));
INSERT INTO TABLE_2 (ORDER_NR, PRIORITY, WO_STEP, STEP_DATE)
VALUES ('1KKA1T205634', '12', '5', TO_DATE('13-FEB-13 09:00:00','DD-MON-RR HH24:MI:SS'));
INSERT INTO TABLE_2 (ORDER_NR, PRIORITY, WO_STEP, STEP_DATE)
VALUES ('1KKA1T205634', '12', 'K', TO_DATE('13-FEB-13 10:00:00','DD-MON-RR HH24:MI:SS'));
INSERT INTO TABLE_2 (ORDER_NR, PRIORITY, WO_STEP, STEP_DATE)
VALUES ('1KKA1T205634', '12', '5', TO_DATE('13-FEB-13 11:00:00','DD-MON-RR HH24:MI:SS'));
INSERT INTO TABLE_2 (ORDER_NR, PRIORITY, WO_STEP, STEP_DATE)
VALUES ('1KKA1T205634', '12', 'K', TO_DATE('13-FEB-13 12:00:00','DD-MON-RR HH24:MI:SS'));
INSERT INTO TABLE_2 (ORDER_NR, PRIORITY, WO_STEP, STEP_DATE)
VALUES ('1KKA1T205634', '12', '5', TO_DATE('13-FEB-13 16:00:00','DD-MON-RR HH24:MI:SS'));
INSERT INTO TABLE_2 (ORDER_NR, PRIORITY, WO_STEP, STEP_DATE)
VALUES ('1KKA1T205634', '12', 'C', TO_DATE('14-FEB-13 08:00:00','DD-MON-RR HH24:MI:SS'));
INSERT INTO TABLE_2 (ORDER_NR, PRIORITY, WO_STEP, STEP_DATE)
VALUES ('1KKA1T205634', '12', 'B', TO_DATE('14-FEB-13 10:00:00','DD-MON-RR HH24:MI:SS'));
INSERT INTO TABLE_2 (ORDER_NR, PRIORITY, WO_STEP, STEP_DATE)
VALUES ('1KKA1T205634', '12', 'E', TO_DATE('18-FEB-13 13:00:00','DD-MON-RR HH24:MI:SS'));
INSERT INTO TABLE_2 (ORDER_NR, PRIORITY, WO_STEP, STEP_DATE)
VALUES ('1KKA1T205634', '12', 'F', TO_DATE('20-FEB-13 16:00:00','DD-MON-RR HH24:MI:SS'));
INSERT INTO TABLE_2 (ORDER_NR, PRIORITY, WO_STEP, STEP_DATE)
VALUES ('1KKA1T205634', '12', 'S', TO_DATE('21-FEB-13 08:00:00','DD-MON-RR HH24:MI:SS'));
INSERT INTO TABLE_2 (ORDER_NR, PRIORITY, WO_STEP, STEP_DATE)
VALUES ('1KKA1T205634', '12', 'R', TO_DATE('21-FEB-13 09:00:00','DD-MON-RR HH24:MI:SS'));
INSERT INTO TABLE_2 (ORDER_NR, PRIORITY, WO_STEP, STEP_DATE)
VALUES ('1KKA1T205634', '12', 'U', TO_DATE('28-FEB-13 12:00:00','DD-MON-RR HH24:MI:SS'));
INSERT INTO TABLE_2 (ORDER_NR, PRIORITY, WO_STEP, STEP_DATE)
VALUES ('1KKA1Z300612', '12', 'A', TO_DATE('12-FEB-13 13:52:42','DD-MON-RR HH24:MI:SS'));
INSERT INTO TABLE_2 (ORDER_NR, PRIORITY, WO_STEP, STEP_DATE)
VALUES ('1KKA1Z300612', '12', '5', TO_DATE('13-FEB-13 09:00:00','DD-MON-RR HH24:MI:SS'));
INSERT INTO TABLE_2 (ORDER_NR, PRIORITY, WO_STEP, STEP_DATE)
VALUES ('1KKA1Z300612', '12', 'K', TO_DATE('13-FEB-13 10:00:00','DD-MON-RR HH24:MI:SS'));
INSERT INTO TABLE_2 (ORDER_NR, PRIORITY, WO_STEP, STEP_DATE)
VALUES ('1KKA1Z300612', '12', '5', TO_DATE('13-FEB-13 11:00:00','DD-MON-RR HH24:MI:SS'));
INSERT INTO TABLE_2 (ORDER_NR, PRIORITY, WO_STEP, STEP_DATE)
VALUES ('1KKA1Z300612', '12', 'K', TO_DATE('13-FEB-13 12:00:00','DD-MON-RR HH24:MI:SS'));
INSERT INTO TABLE_2 (ORDER_NR, PRIORITY, WO_STEP, STEP_DATE)
VALUES ('1KKA1Z300612', '12', '5', TO_DATE('13-FEB-13 16:00:00','DD-MON-RR HH24:MI:SS'));
INSERT INTO TABLE_2 (ORDER_NR, PRIORITY, WO_STEP, STEP_DATE)
VALUES ('1KKA1Z300612', '12', 'C', TO_DATE('14-FEB-13 08:00:00','DD-MON-RR HH24:MI:SS'));
INSERT INTO TABLE_2 (ORDER_NR, PRIORITY, WO_STEP, STEP_DATE)
VALUES ('1KKA1Z300612', '12', 'B', TO_DATE('14-FEB-13 10:00:00','DD-MON-RR HH24:MI:SS'));
INSERT INTO TABLE_2 (ORDER_NR, PRIORITY, WO_STEP, STEP_DATE)
VALUES ('1KKA1Z300612', '12', 'E', TO_DATE('18-FEB-13 13:00:00','DD-MON-RR HH24:MI:SS'));
INSERT INTO TABLE_2 (ORDER_NR, PRIORITY, WO_STEP, STEP_DATE)
VALUES ('1KKA1Z300612', '12', 'F', TO_DATE('20-FEB-13 16:00:00','DD-MON-RR HH24:MI:SS'));
COMMIT;And here is what i expect from my query:
SYSDATE 28.Feb.13 14:00
ORDER_NR PRIORITYCREATE_DATE STATUS STATUS_DATE DESCRIPTION AGE_1 AGE_2 WAITNG STEP_A STEP_B STEP_C STEP_5 STEP_K STEP_E STEP_F STEP_S STEP_R
1KKA1T205634 12 10.Feb.13 10:00 U 28.Feb.13 12:00 CLEAN HOUSE 18,083 8,833 2,125 0,833 4,125 0,083 0,750 0,208 2,125 0,666 0,042 7,125
1KKA1Z300612 12 08.Feb.13 14:00 F 20.Feb.13 16:00 REPAIR CAR 20,000 16,042 2,125 0,833 4,125 0,083 0,750 0,208 2,125 0,666 And now the explanation to the query result:
The AGE_1 is the difference in days between the 'CREATE_DATE' and IF EXSIST the STEP 'U' then STEP_DATE or if the STEP 'U' is not found in TABLE_2 then it should show the difference in days between the 'CREATE_DATE' and the 'SYSDATE'
The AGE_2 is the difference in days between the STEP 'A' STEP_DATE and IF EXSIST the STEP 'R' then STEP_DATE or if the STEP 'R' is not found in TABLE_2 then it should show the difference in days between the 'CREATE_DATE' and the 'SYSDATE'
The WAITING is the difference in days between CREATE_DATE and STEP 'A' STEP_DATE
The following columns show the days how long the ORDER_NR stays in these STEP, if an ORDER_NR comes into the same STEP more then one time it should be calculated together.
If the ORDER_NR skips a step it should show a zero in the specific field.
I hope my explanation is good enough, my english skills are far away from good.
Thanks all for your help.
Greets Reinhard W.Hi,
i changed this query:
with t2 as (
select t.*,
lead(step_date) over(partition by order_nr order by step_date) next_step_date
from table_2 t
select t1.*,
nvl(
max(
case t2.wo_step
when 'U' then t2.step_date
end
sysdate
) - t1.create_date age_1,
nvl(
max(
case t2.wo_step
when 'R' then t2.step_date
end
sysdate
) - t1.create_date age_2,
sum(
case t2.wo_step
when 'B' then t2.next_step_date - t2.step_date
end
) step_b
from table_1 t1,
t2
where t2.order_nr = t1.order_nr
group by t1.order_nr,
t1.priority,
t1.create_date,
t1.act_step,
t1.step_date,
t1.employee,
t1.descriptionTo this:
with t2 as (
select t.*,
lead(step_date) over(partition by order_nr order by step_date) next_step_date
from table_2 t
select t1.order_nr,
nvl(
max(
case t2.wo_step
when 'U' then t2.step_date
end
sysdate
) - t1.create_date age_1,
nvl(
max(
case t2.wo_step
when 'R' then t2.step_date
end
sysdate
) - t1.create_date age_2,
sum(
case t2.wo_step
when 'B' then t2.next_step_date - t2.step_date
end
) step_b
from table_1 t1,
t2
where t2.order_nr = t1.order_nr
group by t1.order_nrthen i get the ORA-00979 Error.
Whats wrong?
I have another question.
How can i handle i i want to group to or more 'STEP's in one Column.
in Case of this i want that the column 'STEP_B' contains all days for STEP 'B' and STEP '5'.
I tried already with a + Operation like this:
with t2 as (
select t.*,
lead(step_date) over(partition by order_nr order by step_date) next_step_date
from table_2 t
select t1.*,
nvl(
max(
case t2.wo_step
when 'U' then t2.step_date
end
sysdate
) - t1.create_date age_1,
nvl(
max(
case t2.wo_step
when 'R' then t2.step_date
end
sysdate
) - t1.create_date age_2,
Round( sum(
case t2.wo_step
when 'B' then t2.next_step_date - t2.step_date
end
) +
sum(
case t2.wo_step
when '5' then t2.next_step_date - t2.step_date
end
), 3 ) step_b
from table_1 t1,
t2
where t2.order_nr = t1.order_nr
group by t1.order_nr,
t1.priority,
t1.create_date,
t1.act_step,
t1.step_date,
t1.employee,
t1.descriptionBut this does reply evertime a NULL.
Thank You.
Maybe you are looking for
-
Syncing music with USB port 1.1
I just got an iPod classic 160GB, but it doesn't communicate with my computer properly. I tried to put some songs to the new iPod, but after syncing 20 songs I got the error message "Attempting to copy to the disk "(iPod name)" failed. The disk could
-
Queries related to web-ui configuration.
Hi Experts, I have some queries related to web-ui configuration : I have copied standard component of Lead with values Role Key = Zconfig key, Component Usage, Object Type, Object Subtype= Default and made some changes(renamed some fields) and assig
-
Dreamweaver template-update overwrites content
Currently I'm using the Adobe CS4 Web Premium Suite on a Mac. I've been using Dreamweaver for a very long time but just recently I started to build templates for Contribute and it's been working fine, however, I need help resolving an issue. After de
-
Hi All, We are trying to update COPA-KNDNR with the value posted into BSEG-ZUONR. The scneario is from the F104 transaction, posting of doubtful debt provisions where customer number is updated into BSEG-ZUONR and we wish to update COPA with this val
-
HELPPPPP.....Please.
I just started using the iPad and before I synced it to iTunes, I entered a password. I know the password. I want to enter it. However, the iPad locks me in the screen that says (via an image) to sync to iTunes. iTunes says to enter a password though