Need help on dial backup with ISP

I've been googling around a couple hours and can't find a simple configuration for dial backup to an Internet Service Provider.
So far, what I've been able to find is direct dialing to routers and dial backup using ISDN.
All I need is for a router to dial. The ISP uses PAP/CHAP authentication and dynamically assigns IP addresses to dialup accounts.
I have an 1841 router with a T1 line on S0/0/0. I want it to fail over to the modem on the AUX port and use that as the new default gateway for all traffic.
Any help is appreciated.

I think you can use Dial on Demand Routing (DDR) as described here:
http://www.cisco.com/en/US/tech/tk801/tk133/tsd_technology_support_protocol_home.html
and this particular guide as well:
http://docwiki.cisco.com/wiki/Internetwork_Design_Guide_--_Designing_DDR_Internetworks#Dial_Backup_for_Leased_Lines
Basically your dial connection will not be active until certain traffic will pass through.
Now, to pass traffic only when primary is down, you can define a static floating route as explained above, which is a route with a higher admin distance than the default one, so if the normal route is up, nothing will pass to the dialer, if it's down, the route to the dialer will be used.
To detect that primary route is down, either use dynamic routing or route tracking as suggested.
I hope that helps.
Regards,
bastien.

Similar Messages

Need help on struts configuration with ColdFusion 10 using IIS

We need help on struts configuration with ColdFusion 10 using IIS.
Earlier we were using ColdFusion 8 with IIS 6 for one of our application. This application internally calls struts. After upgrading to ColdFusion 10 struts calls are not loading. We get 404 error.
In ColdFusion 8 struts were configured using actions extension .do in IIS from this file-
C:\ColdFusion8\runtime\lib\wsconfig\jrun_iis6.dll.
But in ColdFusion 10 this file is not present as ColdFusion 10 uses Tomcat in place of Jrun.
Also there is no information in ColdFusion log file.

Duane wrote:
doctormirabilis, Welcome to the discussion area!
1) how can i configure the time capsule in order to operate as a remote base station synchronizing with the relay using the ethernet port?
Configure the Time Capsule to act as a bridge (not distributing IP addresses). Also configure the Time Capsule to create an 802.11n wireless network with a unique network name (SSID). That's it.
2) how can i avoid that my powerbook while accessing my wireless network does connect through the relay station instead of using the time capsule?
Configure the Time Capsule to use a different network name than the WDS link between the 2 AirPort Express (AX). Configure the PowerBook to use the Time Capsule network.
There are 2 pieces of information that you should be aware of...
(1) None of the PowerBooks are capable of 802.11n.
(2) The WDS link cuts your available bandwidth in half. So the wireless link to your neighbor's has a maximum potential of 27 Mbps.
Let's for a minute assume that you have a Mac compatible with 802.11n. In your configuration the time you could take advantage of the 802.11n speed is when the Mac is sending/recieving data directly from/to the Time Capsule.
There would be NO speed increase in Internet access. The speed of Internet access is going to be controlled by the slowest link in the path to the Internet. That is probably the connection to the ISP. The next slowest path is the WDS link to your neighbor's.
Duane,
I am in a similar situation, sharing internet with my neighbor. Do you think it would be plausible to hook up a vonage phone adapter to time capsule's ethernet port if time capsule is bridging from my neighbor's router in the configuration you have described? A check of my upload speed shows 1.67Mbps (powerbookG4 w/ airport extreme). Vonage reccommends 90kbps minimum upload speed. Am I going to lose some speed putting the Vonag adapter behind time capsule?
Thank you

I have misplaced my iPod Touch 4th Generation. According to Find my iPhone, it should show up in offline mode. I need help on locating it with a software or some other way. Help?

I have misplaced my iPod Touch 4th Generation. According to Find my iPhone, it should show up in offline mode. I need help on locating it with a software or some other way. Help?

There is no other way.
Sorry

Need help re-synching iPods with new computer and getting iTunes to...

Need help re-synching iPods with new computer and getting iTunes to recognize our iPods (it doesn't even recognize them when they're plugged in).
Hubby wiped my harddrive for me, so now I need to get everything back in proper places. I'm using windows XP and installed iTunes once again (I believe it's version 8). I also installed all of my iTunes songs. Now I need to know where to go from here. We have 3 iPods and I need to get them all synched once again. I know how to create different libraries for each of us, but I can't figure out how to get our songs back into our iTunes libraries. When I open iTunes and plug in an iPod, iTunes doesn't even show that an iPod is plugged in.
What do I do now to get each of our iPods synched with our own libraries?
TIA
Brandy

Thanks Zevoneer. The "Restart ipod service" worked and itunes is now recognizing my ipod! Hooray!
Okay, now how do I synch all of our ipods with our individual libraries (I don't want all of my kids' songs and vice versa)? We each have hundreds of songs on our ipods that we don't want to lose.
Thanks again!

1750 dial backup with WIC-1ENET

Does anyone have dial backup working with a DSL or CAble link on the WIC-1ENET card as the wan link?
My dial backup doesn't automatically come up when using the WIC-1ENET card. It does work correctly when I use a serial connection as the WAN link such as the WIC-1T card.
Cisco stated something about the E0 interface not sensing the change which caused the dial backup not to come up without pulling the ethernet cable out of E0.
Any help would be greatly appreciated.
Thanks

Hi
Hope this helps...
You need to run object tracking feature to enable automatic fallback.
http://www.cisco.com/en/US/partner/docs/ios/12_3/12_3x/12_3xe/feature/guide/dbackupx.html
regds

I'm a Noob, and need help solving a backup issue.

I previously had an Alienware PC with a 1TB harddrive. I backed up to the cloud using Carbonite.
I decided to get a new laptop and got a MacBook Pro with Retina. It only has 128GB harddrive. My plan was to use a 2TB external harddrive and back up both using Carbonite. Well, turns out Carbonite only does external harddrive backup with PC's not Macs. So, I need help.
I have way more files than can fit on my laptop that need to be accessed and backed up on a regular basis, so it would seem time machine isn't the solution.
What do you do? or would you recommend? What is the best way for someone like me who wants continual access to and backup of a large amount of data? Are there any good cloud based solutions you would recommend?
I appreciate your help!

CMCSK
Bulletproof backups:
The MOST important part in that link was the titled portion marked: Make backups for your backups
My list for the original poster:
Never consider any computer a data storage device, rather a data creation ,sending, and manipulation device. Anyone who thinks data is safe on any computer, even copied upon multiple partitions is making a mistake.
Never backup your data exclusively upon magnetic hard drives or flash storage, nor consider same since magnetic storage degrades over time even under ideal conditions.
Store important data on multiple servers on multiple continents.
Burn important data onto multiple copies of archival DVDs and store same in cool dark fireproof safes, hidden places, secret places, multiple places.
Don’t burn data onto junk DVD’s purchased from consumer level electronics stores. These are not archival long life DVD’s nor reliable, nor trustworthy
When data can be made to be everywhere, then there is nowhere it can be erased or destroyed.
Most importantly know that 2 copies of your data is 1, and 1 is none, and 1000 copies stored in one place or building, is also the same as none when a fire occurs.
Always consider and expect your computer’s hard drive to completely crash anytime, at all times, and thou shalt keep a cloned and updated hard drive handy at all times to return to immediate productivity and avoid program and parameter reinstallation and tweaking.
When your data is decentralized, it becomes both everywhere and nowhere, accessible to all, destructible by none, cannot be collected together or permanently retrieved under any circumstances.

Need help to create report with jpeg/gif image

Hello,
I need help with creating a form with a special jpeg/gif seal. I never done this Java. Until now, I created all forms with ansi C++ with HP escape characters to draw lines, boxs, and text. This form will contain boxes which is populated with database information read from a text file.
Since this form contains a special seal on the upper right, I don't think it can be done with old fashion ansi C++. How can I create a form with Java and create it as a simple exe to just print the form to a specified printer.
Thanks,
John

Hi,
I am creating a form with boxes (lines and text). What is special about this form is that it has an image jpeg or gif at the top right corner. Is is a state department seal. Up to this form, I had used ansi C++ and print out escape HP character to print out the lines, boxes, and text. I have no idea how to print out the image. I am new to JAVA and only 1 class in it. Is there sample code out there to create this type of form with the image? I need a starting point.
Thanks,
John

NEED HELP!!! with my Micro Photo

i need help i was having problems with my computer recognizing my Micro Photo so i was in to recovery menu so then i accidentally hit the reload firmware option and now i cant get it to work it only goes onto the Recovery Menu and i cant get the firmware updater to work and i cnat find no files of the firmware itself...but the weird thing is i can access the Micro Photo itself through my computer and browse it but idk wat to do some plzzz help me

themagooshow,
You don't need USB2.0 but you will need to have at least Service Pack for your Windows XP and Windows Media Player 0 installed.
Jason

Need help - I2C write/read with TAOS TCS3414 light sensor using USB-8451

Hello, I'm new to labview and need help setting up a vi that will allow me to communicate with a digital light sensor (TAOS TCS3414) using a USB-8451. I need to use the sensor to measure light from a light source that I designed and built as part of a project im working on. I've tried looking at several labview I2C exampled but find them to be very confusing. I've used an arduino to interface with the sensor successfully but need to use labview and dont understand how to write the program. The actions are simple; I need initialize the sensor with a simple command and then request data from 8 data registers and then read that data. The data will then be used in further calculations. The portion i need help with is writing and reading from the sensor. I've attached the datasheet for the sensor as a guide. I can also provide the arduino code that i use to read data from the sensor if that would help.
Pleae keep in mind that i am completely new to labVIEW. I really do want to learn from this but need quick results so the more help the better. It would greately appreciate any help or explaination.
Attachments:
TCS3414_Datasheet_EN_v1.pdf ‏1806 KB

Hi Aaron,
Here you go, this is made with a USB-8452.
When you run the code tick the power en dac enable box on.
Maybe you can help me with my problem, I want to use a fiber to sense light from a led.
Do you use any fiber hardware with the TCS3414?
gr,
Attachments:
TCS3414.vi ‏63 KB

Need help in text field with 2D array

text field with 2D array
Hi
I need help to represent (i) in from field and (j) in to field
I and j are 2D an array indices.
This code are not complated
import java.applet.*;
import java.awt.*;
import java.awt.event.*;
//declaring class
public class test3 extends Applet implements ActionListener
{ //declaring the TextField
private TextField fromField ,toField;
//declaring an array
int weight[][];
int m = 99; // m is infinity
int N; // Set of Nodes
int d; // distance
int i; // source Node
int j; // destition Node
//declaring values of text field
private int from = i; // start Node
private int to = j; // end node
public void init()
setBackground(Color.white);
setForeground(Color.red);
//giving labels
Label TITLE2,TITLE1;
TITLE1 = new Label("from:");
add(TITLE1);
fromField = new TextField(5);
add(fromField);
// register listener using void add actionListener
fromField.addActionListener(this);
TITLE2 = new Label("to");
add(TITLE2);
toField = new TextField(5);
add(toField);
// register listener using void add actionListener
toField.addActionListener(this);
// event handler methods
public void actionPerformed(ActionEvent event) {
//declaring textfield
from=Integer.parseInt(fromField.getText());
to=Integer.parseInt(toField.getText());
weight =new int[7][7];
weight[1][1] = 0; weight[2][1]= 2;
weight[1][2]= 2; weight[2][2]= 0;
weight[1][3]= 5; weight[2][3]= 3;
weight[1][4]= 1; weight[2][4]= 2;
weight[1][5]= 99; weight[2][5]= 99;
weight[1][6]= 99; weight[2][6]= 99;
weight[3][1]= 5;
weight[3][2]= 3;
weight[3][3]= 0;
weight[3][4]= 3;
weight[3][5]= 1;
weight[3][6]= 5;
for (int i=1; i<7; ++i) {
for (int j=1; j<7; ++j)

all your base are belong to us

I need help finding a backup history?

i need help figuring out how to restore my ipod its back up but i was wondering if there is some how a feature where i can find like a back up history so i can restore my ipod to a backup from a different date instead of the last backup any ideas? I accidentally jacked up my ipod and i need to see if i can go to a sort of backup history from apple so i can restore my ipod from a different date instead of the LAST back up

This shows what I see if I use the Edit > Preferences > Devices in iTunes.
(Use Alt or Ctrl+B if you don't see the menu bar.)
It shows just one backup for each of four devices (I don't normally update at this machine). As I recall if there were more, the additional backups would contain the restore date as part of the left-hand column.
I suspect you're not going to like what you find.
tt2

New and need help - drag and drop with dynamic text

So I'm doing this project and as an animator I'm not familiar with the whole action script side of flash
Okay so far I've managed to create the whole Drag and Drop feature and it works well, the thing is I want to make it so when you drag in object in the correct spot and new text appears, and I need like six different object with the dynamic text. but I have no idea how to integrated it in my code or where I should start!
So i based myself on some tutorial so theres some code in there that had dynamic text, but not exactly what i wanted
Your help would be much appreciated!
This is my code:
var counter:Number = 0;
var startX:Number;
var startY:Number;
six_mc.addEventListener(MouseEvent.MOUSE_DOWN, pickUp);
six_mc.addEventListener(MouseEvent.MOUSE_UP, dropIt);
five_mc.addEventListener(MouseEvent.MOUSE_DOWN, pickUp);
five_mc.addEventListener(MouseEvent.MOUSE_UP, dropIt);
four_mc.addEventListener(MouseEvent.MOUSE_DOWN, pickUp);
four_mc.addEventListener(MouseEvent.MOUSE_UP, dropIt);
three_mc.addEventListener(MouseEvent.MOUSE_DOWN, pickUp);
three_mc.addEventListener(MouseEvent.MOUSE_UP, dropIt);
two_mc.addEventListener(MouseEvent.MOUSE_DOWN, pickUp);
two_mc.addEventListener(MouseEvent.MOUSE_UP, dropIt);
one_mc.addEventListener(MouseEvent.MOUSE_DOWN, pickUp);
one_mc.addEventListener(MouseEvent.MOUSE_UP, dropIt);
function pickUp(event:MouseEvent):void {
    event.target.startDrag(true);
reply_txt.text = "";
event.target.parent.addChild(event.target);
startX = event.target.x;
startY = event.target.y;
function dropIt(event:MouseEvent):void {
    event.target.stopDrag();
var myTargetName:String = "target" + event.target.name;
var myTarget:DisplayObject = getChildByName(myTargetName);
if (event.target.dropTarget != null && event.target.dropTarget.parent == myTarget){
    reply_txt.text = "Good Job!";
event.target.removeEventListener(MouseEvent.MOUSE_DOWN, pickUp);
event.target.removeEventListener(MouseEvent.MOUSE_UP, dropIt);
event.target.buttonMode = false;
event.target.x = myTarget.x;
event.target.y = myTarget.y;
} else {
reply_txt.text = "Try Again!";
event.target.x = startX;
event.target.y = startY;
    if(counter == 6){
        reply_txt.text = "Congrats, you're finished!";
six_mc.buttonMode = true;
five_mc.buttonMode = true;
four_mc.buttonMode = true;
three_mc.buttonMode = true;
two_mc.buttonMode = true;
one_mc.buttonMode = true;

where you have
xxx.text = ....
is where you're assigning text.

Urgent--dial backup with a PPPOE configuration

Hi all. I have a pppoe for my DSL connection. I cannot get the dial backup to work while the dsl is working.

Hi,
I think there are few problems:
1. the backup interface command should be applied under the dialer interface
2. the dialer interface will never go down unless you shut it
Let' try to configure dialer watch (http://www.cisco.com/en/US/docs/ios/12_0/dial/configuration/guide/dcdbakdw.html) or may be enhanced object tracking (http://www.cisco.com/en/US/products/sw/iosswrel/ps5413/products_feature_guide09186a00801d862d.html).
Hope it helps, rate if does
Krisztian

Need help on ammount formating with num{$z,zzz,zz9.99}

Hi All
Need help in formating the amount fields.
Currently I am using num{$z,zzz,zz9.99} Its working fine for positive ammount value.
But for negative amount its giving output as $-18,970.50
Expected out is -$18,970.50
need '-' sign before $
Thanks,
Abhijit

issue resolved by setting pattern as = num{z$z,zzz,zz9.99}

Need Help ASAP!! with iPod Classic 80GB

This is my first apple product and it is not giving a good impression. I need help eargently!
I Sync 2969 songs onto my ipod for first time 2 days ago using latest Itunes it worked great and i was happy just my ipod didnt have all the album art, so the next day i plugged it in and put all the album art to the correct albums which went fine, then i wanted to add another album. I clicked sync to update the library on my ipod and it started transfering at a sluggish speed simular to this 1....2....3....4....5....6 etc it eventually got to 196 out of 1248 and stopped and 2 mins later itunes crashed. so the only way i could remove my ipod was to pull it out without ejecting it i then tried to look for the songs and what do you know it said on my Ipod 0 Music..... I was gob smacked i put it back in, in hope for it to sync again but ever since then it continues to do that, but i can manually transfer max 4 albums by drag and drop, at a time before itunes crashes. I am seriously going to throw it in the bin soon if i cant get it working and i will never ever buy an apple product again, i love the idea of the iPod but there to faffy! compared to a standard MP3 player..
PLEASE HELP ME i have tried restoring it many times, ive tried resetting it holding menu button and select button. and i have also tried another way were you restard the ipod and during the apple logo you quickly hold play which formats it..
please help me!! apples help lines are useless!

You do understand that this is a user-to-user forum? That we're all volunteers? And this is a weekend? You may need to be a bit more patient.
If I had an answer I would be happy to try to help. When you say you've tried "restoring" it, do you mean that you've hooked it up to your computer and pressed the "Restore" button in iTunes? If not, that's the next thing you should try.
I know you've tried a few things but it wouldn't hurt to go through the standard trouble shooting steps:
http://www.apple.com/support/ipod/five_rs/
Best of luck.

Need help on dial backup with ISP

Similar Messages

Maybe you are looking for