Need help on OC MSI P45/Q6600

Guys,
I am not able to get my board running above 370 FSB. When i boot using 400 FSB i am able to get to Windows XP 32Bit boot Screen and after the boot i get a blank screen with nothing happening. I even tried Windows Vista 32Bit which atleast boots up completely but hangs as soon as i see the desktop. I only manage to have a stable OS running at 370 FSB Anything above that i get some or the other problems. Any help on getting past 400 FSB stable will be really apprciated.
Thanks!
My configuration is the following :
Q6660 2.4 GHz GO Stepping
MSI P45 Zilent
Palit HD 4850
G-Skill 1066 5-5-5-15 2.0V - 2.1V
500WATTS - VIP
Hear are my OC settings :
Motherboard OC Jumper set to 266-333
================================
C1E: Disabled
Green Power: All Disabled
================================
Multi-Step OC Booster: Mode 2
DOT Control: Disabled
Intel Eist: Disabled
intel C-State Tech: Disabled
Adjust CPU FSB Frequenxy (MHz): 400
Adjust CPU Frequency:3200
CPU Multiplier: 8
================================
Advance DRAM Configuration: Manual
CAS Latency (CL): 5
tRCD: 5
tRP: 5
tRAS: 15
Advanced memory Setting: Auto
FSB/DRAM ratio: 1:1:20
Adjusted Dram Frequency: 800
================================
ClockGenTuner: No Changes Done
Adjusted PCI Frequency: Default
Auto disable DRAM/PCI Frequency: Enabled
================================
CPU Voltage: 1.37v
CPU GTL REF0: Auto
CPU GTL REF1: Auto
Dram voltage: 2.1v
DDR_VREF
DDR_VREF_A: Auto
DDR_VREF_B: Auto
MCH Voltage: 1.36
MCH GTL REF: Auto
VTT FSB Voltage: 1.25
ICH Voltage: Auto
================================
Spread Spectrum: Disabled

Quote
Has anybody been able to get stable 400 fsb with this board ?
>>Yes.<<
Please set the OC-Jumpers to the "266 -> 333" MHz position and try again from there.

Similar Messages

Need help with fixing msi gt683 laptop

Hello. I have a GT 683 R that i bought a couple of months back, i recently did a factory restore on it and afterwards i didn't have the disk to finish the process, so i started messing with the settings and everything i reset the raid to non raid and now i'm stuck on a screen that says "Reboot and Select proper Boot device or insert boot media in selected boot device and press a key".
I tried using the recovery again and it wouldn't even boot to that menu, i hit F11 to try to boot from disc but all it does is go to the reboot and select proper boot device screen.
I need a lot of help on this because i'm not really good with computers.

if you switch from AHCI or IDE, back to RAID in the BIOS (by pressing DEL when the MSI logo appears on the screen, and going to "advanced options")
does it boot into the recovered system ?
switching into/out of RAID mode, requires you to use the RAID setup screen to configure the RAID when it's installed, by pressing ctrl + i when you see the RAID screen just after the MSI logo screen on booting up each time.
as for recovery, you may have more options depending on if you break the RAID, or if you have a backup of windows 7 or a way to copy the ISO to a USB. or just put in the recovery DVD's (mine weren't too helpful)
i.e. http://forum.notebookreview.com/msi/672814-need-help-installing-ssd-gt683r-raid-0-a-2.html
switching out of RAID mode is tricky because the controller makes small changes to the HDD's so they are recognised as RAID.
typically, windows won't let you see the drive if the flag is set, but you can wipe the setting out using backup/clone software or low-level tools that bypass the normal windows settings to blank the drive.
or you can use the RAID setup screen to remove the drives from the array, which is quite a lot faster and less effort, but you will lose all the data on the drives in both situations when switching from RAID, to 2 drives.

Need help regarding SSD - MSI GT60 2PE

Hi all,
I have purchased a "GT60 2PE DOMINATOR PRO", but I don't quite understand what this means:
Quote
Up to 384GB Super RAID 2 + 750GB HDD 7200rpm
Specifically, the "Super RAID 2" stuff. The particular model I'm getting has a 1TB 7200rpm HDD, and no SSD.
My question is, will a "Samsung 840 EVO 250GB 2.5 inch Basic SATA Solid State Drive" be compatible? I don't understand what size or type any of these SSD's are. This is my first time with a high-end computer. Sorry for the lack of links by the way, apparently I'm not allowed post 'em.
Thanks in advance!

Quote from: pilsnermonkey on 18-June-14, 04:59:03
I'm not certain whether or not your model is set up for Super RaID. I has a similar question that is explained here: https://forum-en.msi.com/index.php?topic=180343.msg1297750#msg1297750
The laptop must be configured with the Super Raid adapter. I thought all the Dom Pro's came with it and was disappointed to discover that is not the case.
I purchased a 500GB Samsung SSD following that bit of disappointing news and intended on doing a clean Windows install on the new SSD ... I planned on then using my 1TB drive that came with my GT70 Dom Pro as storage. I discovered that I can't do a clean install on the SSD without purchasing ANOTHER copy of Win 8.1. Seriously.
Looking for solutions at this thread: https://forum-en.msi.com/index.php?topic=181164.0
While some of this is true, some is not.
You do NOT need to purchase another copy of Windows 8.1....You need to use the MSI Burn Recovery disks that you should have made after turning the notebook on for the first time to install Windows onto your new SSD. I've done this, many other users have done this, it's what you do to install a new SSD/HDD.
As for the SuperRaid, since the model the user is buying only has a single 1TB HDD in it, it will NOT have SuperRaid adapter, and they would need to purchase a 2.5" SSD in order to install an SSD into the laptop.

Need help overclocking on MSI X48C Platinum please

hi all i have just installed a MSI X48C Platinum board today but the bios is a bit confussing for me as ive never had a overclocking mobo before
i woud like to OC to 3GHZ to 3.5 GHZ if possible but need some explaining on how to do this and in what sections in the bios to achieve this please
can anybody help me with this please?
Vista X64 SP1
Q6600 B3
MSI X48C Platinum
HD 4870
OCZ 667MHZ 5300
Samsung 20" 2032BW
FSP Epsilon 600 W

Quote from: Frankenputer on 24-September-08, 04:47:11
PC Power & Cooling have a long reputation as being a high-end PSU manufacturer(also been doing it much longer). If paying the extra £15.00 doesn't mean much, then go for the PC P&C. If the funds are tighter, get the Corsair. I have the PC P&C Silencer 750.
My guess Henry, is that kmufc77 was linking to either of these Silencer 750 PC P&C PSUs
http://www.overclockers.co.uk/showproduct.php?prodid=CA-004-PP&groupid=701&catid=123&subcat=&name=PC%20Power%20&%20Cooling%20Silencer%20750%20Quad-Crossfire%20PCI-E%20750W%20Power%20Supply
or
http://www.overclockers.co.uk/showproduct.php?prodid=CA-001-PP&groupid=701&catid=123&subcat=&name=PC%20Power%20&%20Cooling%20Silencer%20750%20Quad-SLi%20PCI-E%20750W%20Power%20Supply
The Silencer 610 would be more than enough for the 4870, but the 750 will give greater overhead and room for upgrades to more power hungry components or Crossfire.
http://www.overclockers.co.uk/showproduct.php?prodid=CA-001-PP&groupid=701&catid=123&subcat=&name=PC%20Power%20&%20Cooling%20Silencer%20750%20Quad-SLi%20PCI-E%20750W%20Power%20Supply
yes you are right i have ordered the Silencer 750 PC P&C PSUs but a black colour not red i payed the extra over the corsair 750W purely on the repitation of PC P&C PSUs. i hope i have made the right choice as i considering crossfire in the very near future

Need help overclocking on MSI X48C Platinum with DDR3 14400

hello everybody
i just installed an MSI X48C Platinum but i woud like to OC the cpu
to around 3GHZ , and play with ddr3s @ 1800mhz with cas 8-8-8-24
or less.
These are the settings i'm using atm: all defaults
q6600
cpu 2400 mhz
fsb 266 mhz
multiplier 9x
OCZ DDR3 PC3-14400 Platinum Edition
fsb/memory ratio: 1:2.00 (auto)
running @ 1067
cas 6-6-6-18 (auto)

how far can you get with your FSB Clock Speed? Have you tested anything yet?

I need help with my MSI Dragon edition 2 with windows 7 64 bit home edition

I recently got my laptop from Xotic PC with windows 7 64 bit home version which was free. The only problems I have for the laptop is that I can't detected the Nvidia Geoforce GTX 780m graphics card on my system or update it, games on steam tend to lag like Metro the last night which came free for me but even at low settings the lag was really bad. Sometimes the screen starts flickering becasue of a display driver error after playing a game or closing a game. So if anyone can help me with these issues I would really appreciate helping me fix these errors.

Please click link below to download driver.
http://www.msi.com/service/download/nbdriver-19693.html
or you can use GeForce Experience, keep drivers up to date.
http://www.geforce.com/geforce-experience

NEED HELP WITH A MSI CW-RW (msi 8348) BURNER

Hi does anybody know where i can find the firmware for a msi 8348 CD-RW as i have looked all over the net but had no look
can anybody help?
thanks

If you can figure out which one, firmware links are on the linked pages:
http://www.msi.com.tw/program/search/ser/SerConProRes.php?keyword=8348&kind=5

Need help Flashing to MSI's new Bios revsion for the MSI GT70 0NC

MSI just came out with a new bios revision for the MSI GT70 0NC I was wanting to know which bios revision is for my MSI notebook?

Hello again my friend, yes it's me again. Here's a screenshot from our last bios flash you helped me out with. Remember I have Windows 8 and still used the MSI flashing tool because I have the older MSI GT70 0NC So I was wanting to know which of the new ones I can obtain and download for my notebook again.

Need help overclock the MSI N580GTX Lightning Xtreme Edition !

I want to overclock this card MSI N580GTX Lightning Xtreme Edition (MSI N580GTX Lightning Xtreme Edition GeForce GTX 580 (Fermi) 3072 MB 384-bit GDDR5 PCI Express 2.0 x16 HDCP Ready SLI Support Video Card), but I don't know how far I can get. Can you help me overclock this to get a maximum performing? and how can I do that? can you guide me?
what is temperature should be consider over heat and might damage card?
After overclock, can I keep that always in 3-5 days without shutdown computer?
Here is default Corelock 832, Shaderlock: 1664, memory clock 2100
Also, when I click the "K" to show MSI Kombustor: I see Core: 416, and GPU Throttling -416Mhz. What is happening? is that graphic card has problem? it doesn't run fully 832mhz.
Here is information of my computer:
Motherboard   Asus Maximus IV Extreme-Z
Processor   Intel Core i7 2600K
Memory   Corsair Dominator Platinum 32GB (4x8GB) DDR3 1866 MHz (PC3 15000)
Video Card # 1   MSI N580GTX Lightning Xtreme Edition GeForce GTX 580 3072 MB
Hard Drive # 1   Corsair Force Series GT 120 GB
Hard Drive # 2   Western Digital Caviar Black 1 TB
Power Supply   Corsair HX1050W
Case   Corsair Graphite Series 600T
Monitor   Acer HN274H BMIIID 3D 27-Inch LED Monitor - Black
Operating System   Windows 7 Utimate (64 bit)

Quote from: flobelix on 02-December-12, 01:03:03
Playing aan entire level of Crysis or Crysis2 with extreme settings is a very sure way to test. A multiplayer round of BF3 at max settings is also a good test.
If you got the max stable clockrates without overvolting and temps are fine. Go on adding voltage in small steps and agin try the highest max clockrate of any voltage step. That way you'll find the total max clockrate. At some point adding voltage will have no effect anymore and that is the highest clockrate. Remember that voltage unlike just higher clockrates will increase the temps massively.
Agreed with flobelix
Crysis 2 with ultra setting and set Vsync to Disabled is a very hard test in real life application, I don't use furmark or kombustor. To test stability first I run Vantage and 3DMark2011 then playing Crysis 2 about 2 - 3 hours every day for aweek or 2 weeks and if pass then I call it stable
I use GTX580 Lightning and at stock volt I can do 920/2200 with all little DIP switches turned ON/Enabled/Unlocked excluding Xtreme cooling LN2 DIP switch since I use normal air cooling and not LN2. If I let all DIP switches to their stock/OFF even at 900MHz I can't pass Vantage.
For safe daily OC better stay under 80c for your core temp and under 70c for your VRM & Memory temp also do not use beyond +200mv for your core voltage (+200mv is the max value)
Note : For 24/7 I use 980/2300 with +112mv/+40mv. VRM and memory temp are under 60c and Core temp is under 80c.

I need help with my MSI 52x/24x/52x cd-rw!!

I just bought this new cd-rw to burn my cd's faster. And so i hoped i could burn cd's at atleast 40x when i had cd's compatible to it, but NO! I've tried both EProformance 40x compatible and Memorex 48x compatible, and none of these will burn on speeds higher than 16x. Now why would i burn at 16x when my old cd-rw went at that speed? I've tried both Nero and Easy CD Creator 6 and none of them allows higher than 16x. I also tried to install the 150D driver thingy, but when it scans the bus, it just shows "No CD-Rom/rw found".AARGH, i get so pissed at this, please help neone, either with how to mod the progs to allow useradjustable speeds or how to make this sh&% work!

similar to flashing the utility is trying to use the drive
and cannot as its ntfs and dos cannot read it
http://www.msi.com.tw/html/support/bios/note/ntfs.htm
get me boot drive
http://www.nerdlabs.org/bootdisks/diskimages/bootme.exe
boot to that
change to floppy with your utility and new firmware on
copy them to ram drive,c probabley it says as me disk boots up
changeto c prompt and run them from c prompt

Need help to oc msi p43 neo

hello all,
I just got my new computer fresh from the shop:
cpu - c2d e5200
cpu fan - arctic cooler freezer pro 7
mobo - msi p43 neo
(http://global.msi.com.tw/index.php?func=proddesc&maincat_no=1&prod_no=1484)
memory - kingston 800mhz 2gb*1 value - I think the timings are 6-6-6-18
gpu - sapphire radeon 4850 dual slot fansink
psu - jsp-tech (ezcool) 450w
hd - wd 640gb
case - silverstone ps02b with two case fans
bios version is 1.7
OS - windows xp sp3
I want to do a moderate oc on this baby, but I'm afraid since it's my first time. I read a lot from the internet and also the manual but still have several questions.
1) I understand that in this mobo there is no need to adjust the pci and pci-e bus?
2) I plan to do a modest oc - raise it only to 3.0ghz. the bios has gray "auto" next to all of the voltages brackets. can I keep it in "auto"?
does "auto" means stock voltages or will the voltages rise when I'll raise the fsb?
I don't want to "overvolt" just yet.
3) I understand that I need to change DOT, c1e, EIST, spread spectrum to "disable". but I want to keep the EIST and c1e for power conservation. will that effect my oc, considering it's a modest one?
4) is raising the fsb from 200->240 keeping the multiplier 12.5 (240*12.5=3.0ghz) and changing the FSB:DRAM to 1.66 a good option or should i try another one?
5) is there other items I should change in the bios?
If there is anything else that you can suggest, pls do. thank you in advance for your kind reply.

if your going to oc it in 3.0 ghz just raised the fsb 286.. reboot and see if theirs and error..
dont change anything yet..

MOVED: need help overclocking on MSI X48C Platinum please

This topic has been moved to Overclockers & Modding Corner.
https://forum-en.msi.com/index.php?topic=120153.0

Quote from: Frankenputer on 24-September-08, 04:47:11
PC Power & Cooling have a long reputation as being a high-end PSU manufacturer(also been doing it much longer). If paying the extra £15.00 doesn't mean much, then go for the PC P&C. If the funds are tighter, get the Corsair. I have the PC P&C Silencer 750.
My guess Henry, is that kmufc77 was linking to either of these Silencer 750 PC P&C PSUs
http://www.overclockers.co.uk/showproduct.php?prodid=CA-004-PP&groupid=701&catid=123&subcat=&name=PC%20Power%20&%20Cooling%20Silencer%20750%20Quad-Crossfire%20PCI-E%20750W%20Power%20Supply
or
http://www.overclockers.co.uk/showproduct.php?prodid=CA-001-PP&groupid=701&catid=123&subcat=&name=PC%20Power%20&%20Cooling%20Silencer%20750%20Quad-SLi%20PCI-E%20750W%20Power%20Supply
The Silencer 610 would be more than enough for the 4870, but the 750 will give greater overhead and room for upgrades to more power hungry components or Crossfire.
http://www.overclockers.co.uk/showproduct.php?prodid=CA-001-PP&groupid=701&catid=123&subcat=&name=PC%20Power%20&%20Cooling%20Silencer%20750%20Quad-SLi%20PCI-E%20750W%20Power%20Supply
yes you are right i have ordered the Silencer 750 PC P&C PSUs but a black colour not red i payed the extra over the corsair 750W purely on the repitation of PC P&C PSUs. i hope i have made the right choice as i considering crossfire in the very near future

Need Help for my MSI gt60 0NE f3 hotkey

Hi guys, i brought MSI gt60 0NE october 2013 i installed games but now i want it back to factory reset. i used f3 hotkey for factory reset.
the question is after pressing f3 I should have an msi recovery manager pop up, but that is not what is happening. After pressing f3 the windows boot manager comes up. Under choose an operating system windows 7 is highlighted and I press enter. then system recovery option pop up (with the list of Repair your Computer,Systems Recovery etc.) instead of MSI manager option.
im looking for MSI manager option rather than system recovery option...

Not much you can do. Opening is pretty much a no go with tablets so a repair at your expense might be the only chance.

Need help to Oc Msi p67a GD55

someone can help me with some advices for oc p67agd55 , and i5 2500k ? in want a little oc at 4000-42000.bios is last version 1H.thx for your help.

if your going to oc it in 3.0 ghz just raised the fsb 286.. reboot and see if theirs and error..
dont change anything yet..

MSI GTX 460 Hawk hangs, need help

Hello!
Need help with my MSI GTX 460 Hawk.
Sometimes it hangs and I need to restart my computer and sometimes screen goes black and then windows says that video driver wasn't responding and was recovered.
Computer hangs more often in the 3D game, but in not 3D programms computer hangs too, but no so often.
The temperature is ok, maximum is 70 deg. in 3D game. I even tried to set videocard cooller to 100% and it didn't help.
I did no overclocking or anything like this.
I use the latest videodriver from nvidia's website and the latest directx.
Windows 7 64bit.
Can you help me to solve this problem?

Quote from: flobelix on 25-August-13, 00:21:30
Follow >>Posting Guide<<
If you are really in lack of parameters:
Board: Gigabyte GA-EP45T-UD3LR
VGA: MSI GeForce GTX 460 Twin Frozr II
PSU: Raidmax 500W (22A on 12v rail)
Intel Core 2 Duo 8500 3.16GHz LGA 775
OS: Windows 7 64bit
The problem: Videocard began to hang:
Sometimes it hangs and I need to restart my computer, sometimes I get BSOD and sometimes screen goes black and then windows says that video driver wasn't responding and was recovered.
Computer hangs more often in the 3D game, but in not 3D programms computer hangs too, but no so often.
What I've allready tried:
1. Installed latest drivers from nvidia.com and latest directx.
2. Checked temperature: maximum is 70 deg. in 3D game at 100% load. I even tried to set videocard cooller allways to 100% and it didn't help.
3. Installed MSI Kombustor to burnin test videocard, but I can't catch any hangups with it.
4. Checked windows system log. The last warning after driver recovery message is:
Video driver nvlddmkm wasn't responding and was recovered.
5. Two latest BSODs were caused by dxgkrnl.sys and nvlddmkm.sys drivers.
6. Finally installed MSI LiveUpdate, it shows that no videodriver is installed and wants to download an old videodriver ver. 258.96.
Need help to solve this problem.

Need help on OC MSI P45/Q6600

Similar Messages

Maybe you are looking for