Need help plz MSI Z68A-G45-B3 Intel Z68

hi all i am getting on this board when i load speed fan this msg
ERROR: Fan Controller 0 can't find PWM (Winbond W83667HG@$290(onISA@$290))
Loaded 0 events
my cpu fan always seems to be at 100% but the cpu is not hot on idel seems to be like 30c i have disabled the smart fan and makes no difference,
also my case fans do not seem to be controlled by the board eather they seem to sit at 1 speed all the time i am running the latest bios i have tried every thing is this faulty

>>Posting Guide<<
Quote
my cpu fan
What kind of fan? 3-Pin/wire fan or 4-Pin/4-Wire PWM fan?
Quote
when i load speed fan this msg
ERROR: Fan Controller 0 can't find PWM (Winbond W83667HG@$290(onISA@$290))
Loaded 0 events
Well, that is a speedfan error, we cannot deal with that here (it is a problem of the software).

Similar Messages

MOVED: Need help with msi mega 180 + athlon xp-m combo

This topic has been moved to Overclockers & Modding Corner.
Need help with msi mega 180 + athlon xp-m combo

AFAIK, you shouldn't need a pinmod for a Mobile Athlon XP CPU to work in a nforce2 mobo
did you have any other CPU installed prior to this one? if so, refer here to clear the CMOS: Clear CMOS Guide
next, refer to your manual, or download from MSI, for location of the FSB jumpers; ensure J8 is shorted across pins 1-2, and J7 is shorted
finally, enter your BIOS setup menu, and under Advanced Chipset Features, set CPU FSB to 133mhz (or even 166mhz if you have DDR333 memory). the only thing i can't see in the Mega 180 manual is where you set the multiplier...
which is where the BIOS has limited overclocking features, and you might have a problem here
i think i'll pass this over to the Overclockers forum, where someone may be able to give a better answer....

MSI Z68A-G45 (G3) Issues

Hi,
Yesterday I took the deliver of a shiny new MSI Z68A-G45 (G3) and managed to install it.
Everything is working fine BUT I can only get the display via the only one of the connectors, either via the on board DVI /HDMI connector or via the ATI 6770 DVI / HDMI connector.
I CANNOT get Multiple displays to work even though Windows 7 detects both the display and I can see them listed in the device manager.
Any ideas?
ps: I had the same setup working in a Gigabyte Z68 motherboard but unfortunately that has developed a fault and hence I went for the MSI MB

The whole point of going Z68 is to be able to run multiple displays using the onboard GPU and a discreet card..
It's my all-in-one PC which acts like a server, desktop PC and media centre.
It seems this motherboard is a no go... I have removed all the cards etc and still it cannot detect multiple displays using the onboard (DVI + HDMI) connections.
It only detects the display on the DVI connection and not the one connected to the HDMI.
I am going to now install back my old MB and see if I can get it all working again.

Where can i order/ship an MSI Z68A-G45 (B3) Motherboard here in the Philippines?

Sorry if this isn't the correct Section to post this.
It seems that the MSI Z68A-G45 (B3) Motherboard isn't available to any retailers/resellers here in the Philippines. My question is when will it be Available here? I can't order one from outside the country because it takes time to arrive and it's going to be very expensive for me. I'm not sure if there's an MSI Branch here in the Philippines, if there is one. I don't have any contact number of them. I really want this Motherboard. Thanks

No one you know thats going across to Hong Kong or Taiwan?

Urgent need of assistance, MSI Z77A-G45 Thunderbolt Unknown problems

Recently I have built my first computer, a desktop with the MSI Z77A-G45 Thunderbolt motherboard, an Intel core I5 CPU and a NVIDIA Ge-Force GTX 650 TI Video Card, and a 850W PSU (way more than what is needed). The computer worked perfectly fine for about a week, I did not initially order a Disc Drive because I figured I could install windows with a flash drive (which apparently does not work) so I installed ubuntu for a while (irrelevant to the problem) I ordered the Disc Drive and when it came in I plugged it in and the computer would not turn on, so I spent a while trying to figure out why it did not turn on when the day before it worked fine, eventually after basically disconnecting almost everything and putting it back together it worked. But it had no signal to the monitor. I have no means of telling if it is a UEFI/BIOS problem, a video card problem, or a CPU problem. All 4 LED's for the CPU phase are constantly on, when before when the computer worked fine it would only have the first phase LED blink, so I believe it might possibly be a CPU problem, though the video card is what controls the output for monitors so it equally could be the problem. For the motherboard I tried just about everything to reset it, everything, except flashing the BIOS (which I don't want to try unless it is the only solution left) I tried to clear the CMOS, took the BIOS battery out and put it back in again. Please help!

I do not yet have access to another desktop in which to put my graphics card. I just tried reseating everything and still no signal to the monitor. The VGA port on my motherboard does not work, it never has for some reason, I did not get intel integrated graphics with my CPU, I am not sure if that is why the VGA does not work.

Need help with msi 875p neo

i just bought one of these and set up my system, but as soon as i flick the power switch on the psu there is a 2 sec delay then it automaticaly boots up without me pushing anything then it just hangs..nothing no boot screen nothing. i check that d brakect thing and it says "Inializing keyboard controller" it stays there and does not change.
my system spec:
msi 875P Neo-FIS2R
intel Pentium 4 3.0GHz 800MHz Fsb
2 x 256 mb pc-3200 OCZ EL-DDR cas 2 @ DDR400
thermal take spark 7
leadtek winfast A280leTD 'Geforce 4 Ti 4200'
WD raptor 36.7 GB SATA 1
Xaser III casing
Thermaltake Purepower 480W
MS intellieye Explorer
plz help me i find no reason for it no to work

Quote
Originally posted by MaKoMaN
thaks for all ur help i found the problem one of my memory sticks had a scratch the other one works fine.. but now what do i do with the scratched one?
did you make the scratch? if not, you got warranty on it that would get you a new one...

Need help with MSI P45 Neo3-FR

I haven't been here in a long time. My old board (just replacing it) worked perfectly for almost 4 years after I ironed out the kinks (MSI 865p Neo2-FISR) but I finally decided to upgrade my rig, but here comes the headaches...
I bought the following for my new setup:
MSI P45 Neo3-FR (came with BIOS 1.3 installed)
2GB (2x1) Corsair Dominator 6400C4D
MSI Radeon HD 4850
Intel Pentium Dual Core E2180 (I want to overclock it hehe)
Lite-On SATA CD/DVD-RW
Old Hardware being used:
Antec TruPower 550W EPS12 (single rail 36amps on +12)
Cooler Master Centurion (forgot what model) Case
Logitech USB Keyboard
Logitech MX518 USB Mouse
2x120mm fans
2xMaxtor SATA 80GB HDDs (note: NOT SATA II, and I want to run these in RAID 0 off the ICH10R, this is specifically why I bought this board I was going to go with the P43-Neo3 over this, but the inclusion of RAID sold me on it)
1xMaxtor SATA 160GB HDD (note: NOT SATA II)
Aside some trouble I had with the Intel HSF installation was a breeze. Everything is in. I wanted to run everything stock first. Jumped into the BIOS and set the following:
SATA Controller - RAID
DRAM Voltage - 2.1v
Drive Layout:
SATA1 - 80GB Maxtor
SATA2- 80GB Maxtor
SATA7 - Optical Drive
SATA8 - 160GB Maxtor
First power on to get into the BIOS was quick. After setting SATA to RAID, POST will hang at Auto-Detecting ACHI Port 1....then find HDD after about 20-30 seconds. And it will repeat itself for Port 2. So its taking me close to a minute (I might be exagerrating but it sure isn't quick and long enough to irritate me having to keep booting) just to POST and even access the BIOS.
Tried to use my current Windows XP install, got to the Windows XP Splash screen and it rebooted. Tried again, with super long ass POST, again rebooted at the splash screen. Said, fine I'll reinstall XP.
While browsing here I forgot where I read about the SATA and long posts, so I changed my 2x80GBs to SATA3 and SATA4, it no longer takes a minute to POST, goes quick as normal.
Set Optical to boot, go into the Windows XP Install screen, F6 for custom drivers, made a RAID disc using three sources (1. RAID drivers from MSI Website, 2. RAID drivers from MSI CD included with Motherboard, 3. RAID Drivers from Intel website) and each time at a certain point I'd get a BSOD.
Tried again by moving my last HDD/Optical to the ICH10 and disabled the Jmicron. Same, BSOD.
Switched off RAID in the BIOS and set it to IDE. AGain BSOD at XP Install.
Started to think it was a Memory issue, ran Memtest both sticks passed.
One thing I noticed in the BIOS, it has my RAM clocked at 1066. Everything is on auto minus the voltage, but I didn't think it would affect it. So I changed the Ratio from auto to 1:2 (800mhz CPU:800mhz DRAM) but still BSOD everytime I try to install Windows.
This is getting frustrating. I've run out of ideas. Any help would be greatly appreciated.

Quote from: BOSSKILLER on 02-August-08, 22:07:06
Read here how to do it:
>>> Slipstreaming Windows XP Service Pack 2 and Create Bootable CD<<<
>>> Slipstreamed Windows XP CD Using SP2<<<
Other option is borrow such installation disk from friends.
I moved away from my "friends" and none PC literate, so I'd be better off driving to the store and buying Vista at this point. Haha.
Okay, going to try this...sounds like that project I started a whiles back but got lazy.
Thanks guys, I'll report any results.

Really need help with MSI R7970-2PMD3GD5/OC:(

Greetings to all,
I really need help with my brand new MSI R7970-2PMD3GD5/OC. I've purchased it two days ago and I didn't really have time to test the card until yesterday. The card is I think way to hot for my "liking". It idles at 56c-60c, at full load in Heaven benchmark 3.0 in 1920x1080, extreme tessellation and 8xAA card reaches 95c-97c. Stock cloacks are 1010Mhz/1375Mhz and stock voltage is 1,174v. Case is being cooled by two Noctua NF-P12 fans. Also I tried lowering the voltage and "underclocking" the card to a standard 925Mhz in small increments, but it doesn't help at all. Each and every time it results in BSOD and dx dll errors and complete system failures. Replacing the card wouldn't be a problem if I lived in a "normal" country that has access to a steady supply. Retailer that sold me a card told me that only 5 cards total have been imported from the launch day and told me that i bought the "last" card in my country. They could order a replacement but it would take them more then a month to do so.:( Ohhh and one more thing I don't overclock, everything in my case is at their default values.
Recently, I read that "Amd released" a bios update for a standard reference boards that turns them into a "GHZ editions". Also lot of users report a lower voltage requirements and lower temps with that "boost bios". As I understand this card pcb is not Amd's reference board design, I could be wrong it's not that uncommon.. So I didn't want to risk warranty by flashing it to a position 1. Will MSI release the boost bios for this model of card? I am humbly asking MSI staff on how to proceed regarding this problem. I would be immensely grateful for any help you could provide.

Quote from: Svet on 24-August-12, 18:13:26
what PC case you use exactly?
have you tried to open PC case side door and to retest?
Hi,
it's open case. If i close it the temps get even worse:(
They get better for other components, but not for gpu. Two Noctua NF-P12's are cooling the case, first one is positioned above gpu, left side next to cpu. Other is right beneath the gpu, right side of case. Just under the hdd section of the case. I tested each and every component with my backup card nv 8500gt. They function within the specified parameters. I'm getting somewhat worried.
П.С. Поздрав Свет
да ли сте ви са наших простора да не куцам на енглеском?

MOVED: Re: MSI Z68a-G45 (G3) Powers up for a few seconds then shuts down; repeats

This splitted topic has been moved to Overclocking, Undervolting section.
https://forum-en.msi.com/index.php?topic=160863.msg1179176#msg1179176

Quote from: moxieman117 on 11-August-12, 08:22:42
Hey guys, just picked up a Z68a-G45 (G3) and I'm currently running the following hardware on it:
i5 3570k 3.4ghz at 95w (I have verified that the mobo is compatible with this chip) with stock cooler
1 DIMM of 4gb Kingston HyperX ddr3 1600 ram
OCZ ZT series 750 watt modular PSU
I currently have the graphics card, SSD, HDD, and CD-ROM out for trouble shooting purposes.
Currently, when I start her up it thinks for a second, powers up, fans spin, and then after a few seconds it dies and restarts.
I went down to 1 DIMM, cleared CMOS, checked for bent pins, even tried a different PSU all with the same result. Is this likely due to the board?
Thanks!
Verified how exactly? Yes that CPU is compatible, but only when an Ivy UEFI/BIOS update has been performed.

HT5312 I need help plz

I need help! I forgot my security question and when I send it to my rescue email but I also forgot that password too so I wanted to change my rescue emial but I don't know how? Can you help me plz!!!

From a Kappy post
The Three Best Alternatives for Security Questions and Rescue Mail
1. Use Apple's Express Lane.
Go to https://expresslane.apple.com ; click 'See all products and services' at the
bottom of the page. In the next page click 'More Products and Services, then
'Apple ID'. In the next page select 'Other Apple ID Topics' then 'Forgotten Apple
ID security questions' and click 'Continue'. Please be patient waiting for the return
phone call. It will come in time depending on how heavily the servers are being hit.
2. Call Apple Support in your country: Customer Service: Contact Apple support.
3. Rescue email address and how to reset Apple ID security questions.
A substitute for using the security questions is to use 2-step verification:
Two-step verification FAQ Get answers to frequently asked questions about two-step verification for Apple ID.

[Please Help]Does MSI Axis 945G support intel core2 duo T7600?

I have an idle CPU intel core2 duo T7600,so I am considering buying an AXIS 945GM to let it work.
I have a question ,does MSI Axis 945G support intel core2 duo T7600?
I checked the CPU suppot list on MSI website,I just found it suppots upto T7400.
Can I flash the new BIOS v1.23 to support T7600?
thank you!

According to the CPU Support List, this won't help. The best thing to do would be to contact MSI Technical Support. Maybe they can give you a more definate answer:
http://ocss.msi.com.tw/

NEED HELP..MSI {6712} KT4v-L bios 1.9

First i need help flashing my bios i have 1.8 now
and want 1.9. I am useing xp pro fully updated on an ntsf file format i have no floppy never needed i have a usb 64meg thumb drive . I do not overclock ever ....
I have read several places how to do this but all are a little different so i decided to ask the real pro you guys.
would some one give me a full very detailed description on how i can do this preferbally soemone who has run into the same situation i have any help would be much appreciated.
MSI KT4V-L {6712}
AMD 2400+ {266}
PNY 256 DDR {333}
PNY 5200 DDR FX 128
Creative Audigy 2 Platinum
Sony 16X DVD
Sony DVD-+RW-+
Creative Labs MegaWorks THX 6.1 600 watts
Antec Lanboy
Antec 300 True Power
Thermaltake 3 speed intake
Thermaltake 3 speed exhaust

i had exactly the same problem - na floppy ever needed
1. burn a cd with ami flash or other flash program and your bios file
2. boot the system with your ( in my case windows 98 se ) cd
3. choose to boot with cd-rom
4. run amiflash from your burned cd
5. enjoy !!

NEED HELP ON MSI 6380 KT266

Please, I Need help.....
first of all, at night, my System seems ok when i print a picture. then the problem came at the morning, when the PC wont even turning on! after some time, about 1-3 minutes, the PC turned on on itself!!! sometimes the PC rebooting it self when the LED indicating the RAM, and the Processor scanned....then i came to the result that the PS was damage, it was 300W PS
then i bought a new 350W PS, and i plugged all, and it seems it isn't solving the problem...but when I move the RAM from bank 1 to bank 2, the system seems more stable....then i have a conclusion that it was the RAM, so i brought the PC to the MSI distributor on my Country ( Indonesia ).
after a while, they doesn't want to replace the RAM / Motherboard ( the Mobo is for 2 years warranty, and they distribute the RAM, Apacer, too ), because they said it was the PS, so they returned it to me....
so, I ask my friend about the PS, and he said that if the +5V below 4.9V then i was the PS, and it's true, it is @ 4,810v - 4.893v on the BIOS....but how this is connected to the RAM bank 1? i have a 25A for +5v at my PS. until now, the only thing i've done is to reduce the FSB to 100, and moving the RAM to Bank 2. but it's still unstable for sometime.....
*ADDITION* and when finally the PC succeed on Windows, suddenly, i hear a sound, similar to when
you turn the system off..."clack" ...when it does, the PC hang, and after a few seconds...it reboot itself
Do you guys here, experts, could help my on my problem? how to increase the +5v? please, help me....i'm so desperate....
this is my spec :
MSI 6380 KT266 Pro
Athlon TBird 1,33 Ghz @ 1 Ghz ;(
ThermalTake V7+
Arctic Silver 3
40 Gb Quantum
PowerColor GeForce 2MX 200
Apacer 256 PC 2100
Nippon Power Supply 350 W

@ Idle : 45
@ Full Load : 48
there are no combination @ my PSU but these are written on the label :
DC Max OUTPUT 350W+
Voltage
230V
Red +5V, 25A --> it's only 25A, isn't it too low?
orange +3.3V, 28A
Yellow +12v, 12A
White -5v, 0,5A
Blue -12V, 0.5A
Puple 5vsb, 2.0A
Gray P/G, OK
and um...what should I do next, wonkanoby?
and..nope...I'm not that noob on CPU thing....and I've use the AS3 about 3-4 months...i spill AS3 on the die at least the same size as a rice ( sorry for the bad english ) :D

MSI Z68A GD55 G3 INTEL RST ISSUE

Hi, i have been trying to install intel RST software to setup my raid 0 but it wont install, it gives me an error saying "This computer does not meet the minimus system requirements to install this software' need help please.
running i5 2500k, 2x 500gb sata 2's, 8gb ram.

Quote
so thats why its not working?
Yes.

MSI Z68A-G45 (B3) slow boot

I've had this mobo installed for a couple of months now and had this problem from the get-go (although different 'codes' on screen). Whenever I reboot I get a black screen with blinking cursor and the number/'code' 98 in the bottom right corner of the screen. The system eventually boots to windows, but it takes about 5 minutes. I've tried pulling all USB devices (except keyboard and mouse). I've changed boot devices in bios, etc. The really strange thing is that it was rebooting just fine for a month or so and started this again. Any ideas?

Quote
This has all the earmarks of it being a compatibility problem with either the keyboard, mouse, or the HDD/SSD may be acting up.
Quote
--Logitech K800 keyboard, G700 mouse
Try with the 10.3 version;
http://www.msi.com/product/mb/Z68A-G45--B3-.html#/?div=BIOS
It also may be a good idea at this point to open a ticket with MSI Tech Support, as it seems to be a compatibility issue IMO;
http://support.msi.com

Need help plz MSI Z68A-G45-B3 Intel Z68

Similar Messages

Maybe you are looking for