Need help reapplying a RAID0 config, without initializing

Hi Evevyone,
First time here, I apologize if I haven't posted in the good section. Though I'm sure the only people who can answer are here.
I'm using a MacPro with an AppleRaid card, using a RAID0. I do know the implications of using a RAID0 and I do understand that losing a drive results in having to rebuild the RAID from scratch.
However, I'm facing a different problem. I got an error from the RAID Utility, saying that 1 of my drives dissappeared, and got removed. This is impossible, as I was next to the machine when it happened, and I'm 100% sure I never removed a drive.
Inside the RAID Utility, All my drives are shown as good, but the RAID stripe is showing "failing" with 1 drive missing.
So, I was looking for a way to use the terminal, to force my drive to be part of the RAID stripe, without initializing it. OR, to recreate the array from scratch, without initializing it.
It can work, or fail, I just want to be sure I tried everything I could, as so far, the drive doesn't look bad... it looks like it's a configuration problem on the card.
Thanks!
Djieff Mute City

Do you have a dial peer now that sends all incoming calls to Callmanager? If so, just configure a translation pattern in Callmanager to translate the called number to the Unity pilot number. If you have other numbers in place, you can look at the config for these numbers. Another possibility is translating the number at the gateway using a translation rule.
Brandon

Similar Messages

Need help in installing Snow Leopard without DVD drive

Hi,
I have a White Macbook 2008 model with 2.1 ghz processor and 1 GB Ram. The dvd rom is not working in my machine. It spits out the dvd's 99 out of 100 times.
I need to upgrade from 10.5.8 to 10.6. Apple has sent me a single disk to install snow leopard.
I am not willing to invest in new dvd drive either internal or external. Needed help on ways to install snow leopard please apart from using the dvd option.
I do have a Firewire 400 cable but i do not know anybody anymore who has a mac machine with 400 port.
Hence the cable is also useless and i cannot connect to anyother macbook and do the install using their drive.
Please suggest.
Regards,
Rahul

There are no direct options. Find a friend with a Mac that has a working optical drive. Buy an 8GB USB flash drive. Partition and format it for the Mac then clone the mounted DVD to the flash drive. Take it back to your computer and boot from the flash drive.
Boot Using OPTION key:
1. Restart the computer.
2. Immediately after the chime press and hold down the
"OPTION" key.
3. Release the key when the boot manager appears.
4. Select the disk icon for the flash drive.
5. Click on the arrow button below the icon.

I guess i need help but i could live without. help if ya want

heres the deal whenever i try to download windows media players for mac, all that comes up is like an icon that looks like a sheet of paper. Then scripteditor or sumthin like that opens and says its unscriptable(whatever that means). seriously guys i need help im not some guy who spends hours on a computer everyday. i just wanted a computer that would work and everthing but this works.

Grant,
Mac OS X 10.4: Where is StuffIt Expander? may help you unstuff the file.
;~)

Need help booting from DMG file without DVD drive

okay so i have 6 computers with me right now. i need to use one that has a dvd drive to install it on a comp that doesnt via firewire.
1- macbook with superdrive and os 10.5 (cant even open tiger install because its a new macbook
2-iBook g4 with DVD drive BUT the firewire port is broken
3-iBook g3 (one that needs tiger but only has a cd drive)
4-ibook g3 (without dvd drive)
5-powerbook g4 with dvd drive and firewire (for some reason will not read the tiger discs i just burned, even though ive already used them on the ibook g4
6-mac pro with firewire and dvd drive, but the dvd drive is broken.
so seems to me, every computer i have has a weakness for exactly what i need. what i need to know now is if i can boot the powerbook g4 from a DMG file of tiger install disc 1 and install is to the target ibook through firewire. if you have any suggestions on what i should try with the supplies mentioned above, please inform me. thanks!

what i need to know now is if i can boot the powerbook g4 from a DMG file of tiger install disc 1 and install is to the target ibook through firewire.
You can't unless the PowerBook is running Mac OS X Server, in which case the NetInstall feature can be used.
(38733)

Need Help: ADAWS install, setup, config

Under the 5.0.2 install guide of ADAWS, editing the Web.Config section, supossedly there is an object DirectoryServices.dll. In our box where ADAWS is installed I do not see this object at all, I have search for it but do not see instance of it on this box. Anyone know where I can find this object.
I am about to go to the step of editing the Web.Config and uncomment the line with section name = "system.directoryservices". I am also at that part to supply the PublicKeyToken value (run sn.exe -T system.directoryservices.dll), but I cannot find the sn.exe either.
Can someone help me out.
Ray Salgado

OK I ran this newly created authentication import and sync job but failing and getting these errors:
9/20/04 14:17:33- Starting to run operations (1 total) for job 'NETMDDEV AUTH IMPORT/SYNC JOB (TEST) - Run Once'. Will stop on errors. (PID=2144)9/20/04 14:17:33- *** Job Operation #1 of 1: Authentication source (for synching users and groups) 'NETMDDMEV SYNC SOURCE (TEST)' [Run as owner 'rsalgado_dev']9/20/04 14:17:33- Creating the Everyone In Auth Source group (if one doesn't already exist).9/20/04 14:17:33- **********************************************************************************9/20/04 14:17:33- Sync Agent is processing groups.9/20/04 14:17:34- Authentication Synchronization Job's call to retrieve the groups on this auth source failed. Please check that the authentication source server is online.*** COM exception was: IDispatch error #19876 (0x80044fa4): [SOAP fault: faultcode='soap:Server' faultstring='Server was unable to process request. --> Object reference not set to an instance of an object. error setting up group query: GetGroupsInternal Error in GetGroups']9/20/04 14:17:34- *** Job Operation #1 failed: ProcessGroups failed (0x4)9/20/04 14:17:34- Done with job operations.
You guys have any ideas on what is going on here???
Please excuse my newbiness on this as I have not setup/configured/ran an AD authentication import and sync job before... Please let me know if I am doing setup / config of any releveant elements wrong...
Ray Salgado

Need Help on using Forge Config Manager and CAS. Questions listed in the content below

Hi All,
I have an existing Endeca pipeline implementation where we read the data sets (Product Catalog Information) from Oracle database using JDBC adapters. The data set undergoes a series of manipulation until it gets indexed to the Endeca system. We make use of PCI for dimensions and dimension values. However, we now want to extend PCI to also include the Product catalog information. The current implementation also does not make use of CAS adapters to consume the dimensions data in PCI. The next consideration is to implement PCI as close to Out of the Box provisions and standardize it. Therefore we are also considering to implement CAS.
The questions are as below:
1. What are the ideal parameters that should support the use of PCI implementation (Dataset + dimension + precedence Rules + schema information) ? Note: We DO NOT have any product catalog system (like ATG) between database and Endeca.
2. Considering that we do not have any product catalog system to organize and maintain data, how feasible is it to read directly from database through CAS Adapters and process the data ?
3. We also plan to introduce partial update pipeline in future releases. Keeping that in mind should CAS based approach help us to read from a record store at the time of partial updates ?
4.in case we are limiting to a business case of implementing partial updates in the above explained existing design, should a custom CAS approach be a better design ? Custom CAS approach = writing the baseline output data to record store and later referring it at the time of partial updates.
5. Will CAS based approach help to reduce the baseline timings ?
6. What is the best way to export data to record store instance in the above design ? (Record store API / Command line utility / CAS crawl)
Thanks,
Nitin

Hi Neeraj,
You cam use both PI SLD and Solman Local SLD for LMDB synchronization. Now here you make to make sure that correct ranks are assigned to PI and Solman SLD. With the help of multiple sld, you can remove the cause of concern. Local SLD should always be of solman.
For CR content. that you can do for solution manager system in a click.
Divyanshu

Need help on FI/CO config

Hi,
Is anyone working with energy company...if so pleeeease let me know the procedures for configuring FI/CO module.
Thanks
van1276

Hi
These are very good sites for interview mat,
http://www.allinterview.com/showanswers/56726.html
http://techpreparation.com/computer-interview-questions/sap-modules-interview-questions2.htm
http://www.surya-padhi.net/fico/fico_index.htm
http://sap.ittoolbox.com/groups/career/sap-career/fico-interview-questions-1498679
Hope it helps
Regards
Jyostna

Need help getting simple Nat config to work

I can't seem to get the below Nat config to work. I removed the crypto from the fa0/0 for testing.
Why can't i get xlates when I ping 192.168.1.5 or 192.168.1.1? As you can see my access list isnt getting touched?
What am i missing?????
==============================================
CCC#sh access-lists
Standard IP access list 1
10 permit 10.10.10.0, wildcard bits 0.0.0.255
==============================================
CCC#sh ip nat t
CCC#
==============================================
CCC#sh ip nat s
Total active translations: 0 (0 static, 0 dynamic; 0 extended)
Outside interfaces:
FastEthernet0/0
Inside interfaces:
FastEthernet0/1
Hits: 0 Misses: 0
CEF Translated packets: 0, CEF Punted packets: 0
Expired translations: 0
Dynamic mappings:
-- Outside Destination
[Id: 2] access-list 1 interface FastEthernet0/0 refcount 0
[0] prot 6: port #7 refcount 1 syscount 1 localport 4294967295, localaddr 0.0.0.
0, flags 1
[0] prot 6: port #9 refcount 1 syscount 1 localport 4294967295, localaddr 0.0.0.
0, flags 1
[0] prot 6: port #11 refcount 1 syscount 1 localport 4294967295, localaddr 0.0.0
.0, flags 1
[0] prot 6: port #13 refcount 1 syscount 1 localport 4294967295, localaddr 0.0.0
.0, flags 1
[0] prot 6: port #19 refcount 1 syscount 1 localport 4294967295, localaddr 0.0.0
.0, flags 1
[0] prot 6: port #21 refcount 1 syscount 1 localport 4294967295, localaddr 0.0.0
.0, flags 1
=============================================================================
CCC#sh run
Building configuration...
Current configuration : 1490 bytes
version 12.4
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
hostname CCC
boot-start-marker
boot system flash c2600-adventerprisek9-mz.124-25d.bin
boot-end-marker
no aaa new-model
no network-clock-participate slot 1
no network-clock-participate wic 0
ip cef
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
archive
log config
hidekeys
crypto isakmp policy 2
encr 3des
hash md5
authentication pre-share
group 2
lifetime 400
crypto isakmp key cisco123 address 1.1.1.3
crypto ipsec transform-set Petaluma_VPN ah-sha-hmac esp-3des
crypto map Petaluma_1 1 ipsec-isakmp
! Incomplete
set peer 1.1.1.3
set transform-set Petaluma_VPN
match address 100
interface FastEthernet0/0
ip address 1.1.1.2 255.255.255.0
ip nat outside
ip virtual-reassembly
speed auto
half-duplex
interface Serial0/0
no ip address
shutdown
clock rate 56000
interface FastEthernet0/1
ip address 10.10.10.1 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
router rip
network 1.0.0.0
network 10.0.0.0
no ip forward-protocol nd
ip route 192.168.1.0 255.255.255.0 1.1.1.3
no ip http server
no ip http secure-server
ip nat source list 1 interface FastEthernet0/0 overload
access-list 1 permit 10.10.10.0 0.0.0.255
control-plane
line con 0
line aux 0
line vty 0 4
login
end

I am getting same issure:
Dynamic mappings:
-- Outside Destination
[Id: 1] access-list NAT interface FastEthernet0/0 refcount 0
[0] prot 6: port #0 refcount 2 syscount 2 localport 4294967295, localaddr 0.0.0.
0, flags 1
[0] prot 6: port #7 refcount 1 syscount 1 localport 4294967295, localaddr 0.0.0.
0, flags 1 Dynamic mappings:
-- Outside Destination
[Id: 1] access-list NAT interface FastEthernet0/0 refcount 0
[0] prot 6: port #0 refcount 2 syscount 2 localport 4294967295, localaddr 0.0.0.
0, flags 1
[0] prot 6: port #7 refcount 1 syscount 1 localport 4294967295, localaddr 0.0.0.
0, flags 1
I don't know what this means and will try debug ip nat and get a readout.

Need Help w/CF Builder Config

I admit I am a Homesite guy but I'm really trying to give CF Builder a fair shake. Unfortunately, I can't even get off the ground with it. I have tried every combination of settings I can think of but I cannot 'Browse' (in Homesite lingo) a CF template with IE or Firefox from within builder.
My CF8 server is another machine on my network. Builder is talking to it - I can use the services browser and such. Just can't browse (preview) my web pages. In Homesite my mappings look like this:
Homesite Path: N:\inetpub\wwwroot
Server path: C:\inetpub\wwwroot
Browser path: http://web1/
ColdFusion is installed in C:\coldfusion8 on the server, which would be N:\coldfusion8 on my workstation. Not sure if that matters or not since Homesite doesn't care...
Using IIS. Port 80
How can I translate this into Builder? This can't be that hard but I've been beating my head against the wall!
Thanks!

Can you browse to the site using an external browser using the URL you are giving to CFB?
Also, it might be good to ask these questions on the CFB forum - http://forums.adobe.com/community/labs/coldfusionbuilder - because the CFB dev team monitor that one.
To be honest, the internal browser in CFB has never worked for me, because it balks at the fact that my project files are in a different location to my source code (which makes sense, because a CFB project has nothing to do with the source code of my app, so why would they be in the same place?), which is something I have raised with the CFB dev team but not had any feedback about.
I just use an external browser.
But, anyway, I reckon if you repeat your question on the CFB forum, the guys there will help you out.
(Sorry, would have mentioned this last time round, but didn't notice you weren't already posting it there... I get email from all the forums into one mailbox)
Adam

Need help: computer reboots whenever java is initiated.

Recently received a used computer with xp installed.
Every time I initiate something to do with java the computer restarts.
For Instance:
in control panel - clicking on the java console.
online - using online storage service "adrive.com" to upload files.
installing - running the java installer for jedit.
Each one of these things causes a reboot.
I've deleted and reinstalled the latest java runtime environment, ran virus/spyware scans, deleted everything from the computer I don't need, and cleaned the registry, but nothing has solved the problem.
Searched for a solution on google and troubleshooting guides, but the terms: java, reboot, xp, etc; are all so common that the results don't come anywhere close to the answer I need.

Wouldn't you know it. After spending all this time searching for an answer, almost immediately after I posted this I found the answer here on this forum:
http://forums.sun.com/thread.jspa?forumID=32&threadID=689707
Thanks to: Caffeine0001
For those who want to know: All I did was update my -Display Adapter- driver through -Device Manager- and ran windows update. Windows update probably had nothing to do with the fix, but it updated .NET to 3.5 and updated IE to version 8.
Good To Go!

HT2534 I need help on creating an account without credit card.

Well, I tried creating an account, but still there's no "None" in the options on choosing a credit card. I'm using my iPad3 on creating an account. What to do?

Hi, I had this problem as well. Everyone kept telling me just to select the "None" option next to the credit card choices -- but I didn't HAVE a "None" option and was getting very frustrated!
It turns out that in this case, you do have to add a credit card to finish creating your Apple ID. Then as soon as it's created, you can go to "Account" at the bottom and immediately remove your credit card information. This worked for me -- my credit card was only in the system for about 15 seconds before I was able to remove it with no problem.
I did this through iTunes, but it might be similar on the iPad....
Anyway, hopefully this works for you as well!!

Trying to be sure I have latest versions of Lightroom and Photoshop (I am on monthly subscription plan). After I sign in - told I need "administrative privileges to continue." The initial downloads went without any problem.

Trying to be sure I have latest versions of Lightroom and Photoshop (I am on monthly subscription plan). After I sign in - told I need "administrative privileges to continue." The initial downloads went without any problem. I am not sure what to do next. My computer is at home. It is a new iMac.

Are you using your Mac with an Administrator account?
A chat session where an agent may remotely look inside your computer may help
Creative Cloud chat support (all Creative Cloud customer service issues)
http://helpx.adobe.com/x-productkb/global/service-ccm.html

HT201407 When I did the latest update, my phone was wiped out completely. My laptop that I had everything on, crashed. I have a new laptop, tried to update on it and of course i couldn't without deauthorizing my account then reauthorizing. I need help!

When I did the latest update, my phone was wiped out completely. My laptop that I had everything on, crashed. I have a new laptop, tried to update on it and of course I couldn't without deauthorizing my account then reauthorizing. I need help! I want my ringtones and picturesd back, and can't get them. Does anyone know how to do this given my situation?
Thanks!

cathorio wrote:
I recently changed my lap top. My problem is the new lap top won't accept my apple I D it asked me to sing up for a new one which I did.
I am puzzled by this. The laptop doesn't need the Apple ID - but iTunes does. I could be missing something but ....
Why would you not be able to use your existing Apple ID and iTunes account on a new laptop? If you authorized the computer - you should be able to use your existing account - unless you already had 5 computers authorized with the existing ID - and that was why iTunes would not accept the ID. However, I'm sure that you would have received a popup message from iTunes telling you that you had reached the limit.
I just received a new MBP and my daughter did as well. My entire family shares an Apple ID and we had no issues at all with my Apple ID and iTunes on our new computers and I did not have to sign up for a new account. Did you even try the old ID?

I ordered a new phone and shipped it to a friend in Dubai, UAE. without knowing i have to activate it by making 5minutes calls, please i need a way to activate it without sending it back to the US..any help? this has been very frustrating for me this past

I ordered a new phone and shipped it to a friend in Dubai, UAE. without knowing i have to activate it by making 5minutes calls, please i need a way to activate it without sending it back to the US..any help? this has been very frustrating for me this past few days

scottxx,
That was very nice of you to provide your friend with a new phone! I am sorry to say that the device will not be able to activate while in Dubai. For a device to activate it must connect to the VZW network to become active. I apologize for any inconvenience.
LindseyT_VZW

I need help,,upgraded to ipad2, laptop had to be restored b4 I backed up iPad or saved iTunes library. How do I back up and sync my ipad2 without losing content on my iPad.

I need help,,upgraded to ipad2, my HP laptop had major issues and had to be restored b4 I could back up and save any content on the hard disc. So i havent backed up my iPad2 or saved my iTunes library.
How do I back up and sync my ipad2 without losing content on my iPad.???
I need really simple instructions as I've had a bad run with my laptop the last month.
I have re-installed iTunes,it currently has no content in it
all my music, photos etc had been saved to a an external Hardrive (phew)so I'm not concerned about losing them during a sync, but how do I sync my Ipad without losing the applications... The last back up saved was in June when I still had an ipad1
I tried to back it up last night but kept getting the prompts something to the effect of "iPad can only be synced to 1 iTunes library, syncing will erase all content and replace with content on this iTunes library".
Help please,, I've already lost endless hours fixing my PC issues,so I'm not game to attempt this issue without guarantee I won't lose everything,need a simple solution that anyone can follow as my brain has information overload!!! Lol
Thanks

This should help you out. I copied this from another discussion a while back. Here is the original discussion link.
https://discussions.apple.com/message/11527071#11527071
This is what is in the discussion. It really doesn't get any easier than this.
1) Without connecting your iPad to your laptop, start iTunes. Click on Edit. Click on Preferences. Click on Devices. Check the box next to "Prevent your iPod etc. from automatically syncing." Click OK.
2) Now connect your iPad to your laptop and start iTunes.
3) When iTunes starts, right click on your iPad under Devices in the left column. Select Transfer purchases etc.
4) After it finishes transferring all your apps to your new laptop, right click on your iPad and select Backup your iPad.
5) After it finishes backing up your iPad, right click on your iPad and select Restore etc.
6) After it finishes restoring, left click on your iPad , then click on the Apps tab on top, and check the box next to Sync Apps, then click on Apply below.
If everything on your iPad looks good after the sync, go back and click on Edit / Preferences / Devices and UN-check the box next to Prevent your iPod etc. The only other thing you may want to check is if your contacts, bookmarks, etc. are syncing correctly now. If not, go to the Info tab after connecting and make sure you indicate which features you want to sync with what sources.

Need help reapplying a RAID0 config, without initializing

Similar Messages

Maybe you are looking for