Need help setting up a network with new Airport Extreme

Hey All I need some help. Networks, Wan, WPA it's all greek to me. Here's what I am trying to do, I have a newer imac, an ipod touch, a apple TV and the kids have a laptop running on Vista. I have a DSL internet connection through Verizon with a Westell VersaLink Model 327W router. I disabled the wireless option on the versalink and hooked the Ethernet cable from the versalink to my Airport extreme. I am trying to figure out how to set things up so I can restrict the kids laptop from the internet after say 9pm but allow everything else unlimited access. I've read other posts and the manual but can't figure it out. When I turn the Airport off Bridge mode i get a bunch of errors re DHCP beginning and ending addresses and have no clue how to set this up. Before I spend hours on the phone with tech support I figured someone out there may be able to help. This can't be to difficult or is it?

rmunoz274 wrote:
I had to call Verizon and spend an hour on the phone, my Versalink is about 3 years old and I never updated it. There is a software update which makes it a little more mac friendly. Cables still run through it on the Ethernet port. I was able to turn the wireless feature off on the Versalink (to stop my neighbors and kids from bypassing the APE and just factory reset the APE and set it up with a shared IP adrs instead of bridging it. Also made sure I turned off the guest network on the APE. Once it was set up I clicked on Airport in the Airport Utility then wireless Clinets, jotted down the client I wanted to restrict access to (Kid's Laptop) then go back to Airport screen, last option on right Access then MAC Adrs Access Control change to "Timed Access", then click the + on the bottom of the window, type the MAC adrs you want to restrict and set time limits, when complete click done..... Only took me a week and a half to figure it out...... Good luck, if that doesn't help let me know, but I'm no expert...
thanks!!
i think i have the most recent 327w update, because it now shows my modem screen in a red color and it is broken into 3 sections across the screen.
as far as the AEBS is concerned, you did not use it in bridge mode at all?
i thought you had to connect 1 cable from it to the 327w? I have about 5 items i will be connecting, so i will probably run any wired from the AESB, but not sure yet?
thanks, and yaeh last time my network took me a bit of time as well!!
what kind of encryption are you running?
thanks

Similar Messages

Help setting up Open DNS with new airport extreme

I cant seem to get Open DNS to work with a new airport extreme. The status says I am not using Open DNS and its not filtering anything. I have followed the exact steps for set up listed on their website, checked the dns settings, cleared both caches and restarted the computer, modem and router with no success. I set the airport up in bridged mode, although I tried the other option under setup, but not sure what I was doing? I picked up this router because I wanted easy set up and the apple store assured me it would work with Open DNS. Oh, and I also downloaded the latest firmware update on the router. Can anyone help me with the settings or what else I need to check?

Sorry, I am not familiar with this product, so I checked online to pick up some information. Here I am referring to the information found here:
http://www.dslreports.com/faq/6096
I found that your device is mentioned as follows in the intro under Section 1 of this document:
The BellSouth supplied Westell 2100, 2200 and 6100 models (Models A90-210030-04, B90-220030-04, and B90-610030-06/C90-610030-06, respectively) share many features and functions.
Next, I am referring to the information under Section 2, under the heading of Standard Default Mode Connection (separate hub or switch present). Unless you have changed the configuration on the Westell, this is how your device is operating. In this mode, the Westell device is acting both as a modem and router in one unit.
So, an attached router (AirPort Extreme) must be configured as a switch to work correctly. That is what Bridge Mode is....the AirPort Extreme is operating as a switch when it is in Bridge Mode (which would be the correct setting to use when the Westell is set to its Standard Default Mode).
Any changes that you want to make regarding DNS settings would need to be made on the Westell device, since it is acting as the main router on your network.
In Bridge Mode, the AirPort Extreme simply passes that information through to its connected devices. You will not be able to make any DNS related changes on the AirPort Extreme since it receives that info from the Westel device. Some service providers force you to use their DNS servers, so you might want to check with Bell South or AT&T for more information in this regard.
If you want to be able to configure the AirPort Extreme as the main router on your network, and instruct it to use the DNS information that you want, you will need to refer to the section under the heading of Bridged Ethernet Mode ( separate router present).
Please note that the first item under this heading specifies that "This is the preferred configuration when using a separate external router..." (which would be the AirPort Extreme in your case)
So, it appears to me that this would be the way that you must reconfigure the Westell device to allow the AirPort Extreme to function as the "main" router on your network. In this type of setup, you will be able to enter the DNS information that you want to use under the setup for the AirPort Extreme and it will act as you instruct.
The AirPort Extreme would not be configured in Bridge Mode for this....it would be configured to "Share a public IP address".
The next item in the article specifies that you "Must use a PPPoE client on the Router." This means that the AirPort Extreme would be configured to Connect Using = PPPoE as follows:
AirPort Utility - Manual Setup
Click the Internet icon
Click the Internet Connection tab
Connect Using = PPPoE
You would enter your user name (probably your email address), password, etc in this area. Leave the Service Area box completely blank. Set Connection to Always On, and Disconnect if Idle to Never
Click Update to save the new settings. Power off the Westell device after this and then restart it so that it will pick up the new information that you have programmed into the AirPort Extreme.
I want to stress that this is how I would try to configure the Westell and AirPort Extreme. But, as I said, have not used a Westell device, so I cannot say that this will work correctly for you.
It might be an excellent idea to contact Bell South or AT&T Support to ask for their opinion on this before you decide to change the configuration of the Westel device and the AirPort Extreme.
This type of thing can be intimidating for users, so you might elect to use the services of someone like the Geek Squad at Best Buy, or a similar service from a local computer firm. Perhaps the Apple store could help as well.
If it is not critical that you use Open DNS, you might want to simply leave things "as is", with the AirPort Extreme in Bridge Mode.

Set up DynDNS access through existing network with new Airport Extreme

Hey everyone!
I just can't seem to figure out what I am doing wrong here...
I am working with an office network which was initially set up with a Linksys router and a separate Linksys hub connecting two Macs and a network printer in one particular room. We added several new iMacs and for ease of connectivity, decided to add a new Airport Extreme base as one of the new iMacs is acting as a server for a database the other new wireless iMacs connect to. Also, all the machines need access to the connected network printers connected in various parts of the office.
What we have now is the original Linksys router -> Linksys hub -> Airport Extreme. Everything seems to be working fine this way but I do believe that both the Linksys router AND the Airport Extreme are distributing IP addresses, which I'm thinking, could be the problem. I set up a DnyDNS account just fine, assigned port # 8080 on the server iMac and also opened port 8080 on both the Linksys and Airport Extreme. I still cannot get through to the server via DynDNS however.
I am wondering if I should turn off IP distribution on the Airport Extreme and let the Linksys router handle all that? The software that the other wireless iMacs run to access the database on the server depends on the server IP address too, so will this need to be changed if the Linksys is handling IP addressing? How does the hub affect any of this... does it change or interfere with the addressing in any way?
Thank in advance for any ideas or suggestions!

maxyourmacs, Welcome to the discussion area!
I am wondering if I should turn off IP distribution on the Airport Extreme and let the Linksys router handle all that?
Yes
The software that the other wireless iMacs run to access the database on the server depends on the server IP address too, so will this need to be changed if the Linksys is handling IP addressing?
Probably
How does the hub affect any of this... does it change or interfere with the addressing in any way?
It has no affect.

Setting up wireless network with 2x airport extreme ac

I've got a business customer with 2 new Airport Extreme 802.11 AC behind a comcast modem.
When the first extreme is set up, all is well.
When the 2nd Extreme is introduced, Airport Utility asks to automatically wirelessly extend the network, which I allow it to do.
But sometime during that setup, the 2nd extreme becomes unresponsive, and the connection to the internet becomes broken.
The only thing that restores it is to reboot the first Extreme. No matter how many times Iv'e done this, it results in the same problem. I've replaced Extreme #2 with a new one, and I get the same problem.
There are 20 some odd devices on the network; with one Extreme, it works great, and the Extreme AC's replaced 2 older version of Extreme's that were doing this just perfectly.
What is causing this problem, other than me doing something stupid, and how do I extend the network? I'd rather extend it with the wire it's connected to than wirelessly.

Power off AirPort Extreme 2 for now and test the Ethernet cable that is connected from one of the LAN <-> ports on Extreme 1 by temporarily connecting the cable to the Ethernet port on a laptop or desktop. Turn off the wireless off on the computer and see if you can get a good Internet connection that way.
If you can, then you know that the Ethernet port on the AirPort and the cable are both working correctly.
If you can't, then you need to do some troubleshooting to identify the real problem before you can attempt to configure AirPort Extreme 2.
Post back when you have verified that you have a working connection between AirPort Extreme 1 and the device that you are using to test.

Just bought new time capsule- need help setting up WiFi network with another router

Here ismy situation.
I had a wireless network setup up at home using a Belkin wifi router.
I have 2 macBooks (1 pro, 1 air) and 2 iphones that connect wirelessly and a desktop PC that is hard wired to the ethernet port. In addition, I have a Verizon wireless network extender plugged in by ethernet. All of the hard-wired gear is in our 3rd floor attic office (and the wireless signal was strong throughout the house).
The Belkin wifi router was plugged into a wall ethernet jack that is in turn wired into a Linksys router in the basement (along with multiple other ethernet ports througout the house) and is hardwired to the Cable modem next to it. All of the hard-wired ethernet stuff (including the router in the basement) was there when we bought the house, and I have no clue in the tangle of wires how to sort them out (but don't really think I need to)
I just purchased a TimeCapsule to do wireless backups of my 2 macbooks, and tried to set it up alongside the existing wireless modem.
Needless to say, this did not work well. I called AppleCare, and was told that the TimeCapsule needs to be the "1st" wireless adapter, so I went into the basement, and connected the time capsule directly to the cable modem, and then out to the basement router. The Belkin router still needs to be in the attic to supply the PC and the Verizon adapter (so it is near a window for GPS signal).
If I try to name the WiFi network the same SSID on both the TC and the belkin router (to have dual signal strenth coverage) the whole thing gets messed up and the TC cannot be "found" by the aiprort Utility software.
What I have done now is that I have 2 side-by-side wireless networks with 2 unique names (actually 3, because I enabled the 5Ghz signal on the TC), but our wireless devices do not "switch" automatically from one SSID to another stronger signal SSID as we move through the house
Here's the question: How do I name them the same so that the devices will switch effortlessly to the stongest signal? I understand it involves switching the "channels" but don't know how to do it right now. Currently, everything works, so I don't want to mess it up tinkering. Another caveat- there are several other wireless networks from neighbors houses that I can "see". I jsut downloaded a program called iStumbler that shows the channels, but not sure what to do with that info.
Any advice would be appreciated.

Here's the question: How do I name them the same so that the devices will switch effortlessly to the stongest signal? I understand it involves switching the "channels" but don't know how to do it right now. Currently, everything works, so I don't want to mess it up tinkering. Another caveat- there are several other wireless networks from neighbors houses that I can "see". I jsut downloaded a program called iStumbler that shows the channels, but not sure what to do with that info.
Any advice would be appreciated.
OK.. sounds like a mess.. or at least messy and the previous people should have left a log book with all the IP address info in it.. you have far too many routers.. but from here it is impossible to tell how they are configured. Most are probably just setup as AP.
Naming rule for wireless.. Same SSID same security different channel.
SSID ie wireless name to work on the PC side should have no spaces and no special characters. TC name should also follow that rule. So the devices need to all set with fixed channels.
Don't worry too much about iStumbler and what is outside your house.. there isn't enough channels at 2.4ghz anyway. And you are going to need to use them all. There are only three non-overlapping channels. 1, 6, 11 so set each device to one of those channels. The TC should be as close as you can to where you normally use the MacBooks.. and turn on the 5ghz. You will have to leave it to automatic name so the Macbook can also roam across from 2.4 to 5ghz. But if you care to use a different name and force it onto 5ghz the speed is much better as long as you are in the same room.
Roaming is great in theory.. often in practice it just doesn't work.. you need to step in and turn off wireless and then turn it back on.. you can quickly see which router it is connecting to by hold down the option key when you click the airport fan in the top menu area.. and look at bssid.. you will have to figure out which number MAC address relates to which router.
Also do not be surprised if Lion gives you issues. It seems to often drop out and lose connection to the TC as a backup device even if internet is still working.

I am unable to join my existing wireless network with new AirPort Express

I am unable to join my existing wireless network with new AirPort Express.
I am using a DLink DI-524 Router, Windows 7 (64), and the AirPort Express.
AirPort Utility will not recognize the AEX wirelessly, it will only recognize it when it is connected by Ethernet. I can then configure the AEX and verify that the settings stick once disconnected and then reconnected. However, even after that, it will not recognize the AEX once disconnected from the Ethernet cable.
I followed the suggestions of several other threads on these forums. But I am unable to get the AEX to work.
Any suggestions? Thanks in advance.

Welcome to the discussion area!
It's almost always a security setting that causes problems when the Airport Express (AX) tries to join a third party wireless network. The AX usually does not "join" correctly and that's why you can't see it on your wireless network using AirPort Utility.
Using an ethernet cable is still the more reliable way to configure and adjust the AX, but if you are want to try to configure it using wireless, you must return the AX back to factory defaults as follows:
Power down the AX
Hold in the reset button +and keep holding it in+ as you plug the AX back in to power
Release the reset button after 10 seconds
When it is set to factory defaults, the AX broadcasts a wireless signal with a network name like "apple network xxxxxx" where the "x's" are either letters or numbers. You must look for this network by clicking on the fan shaped Airport icon at the top of the screen. If you don't see this network, then click Join Other Network to search that way. Unless you connect to this network, you will not be able to configure the AX using wireless.
Do you know the exact security type that your D-Link router is using? That is the key element in the process.
Open AirPort utility, click Manual Setup
Click the Base Station tab to establish a name for the AX, device password and adjust time zone settings
Click the Wireless tab
Wireless Mode....Join a wireless network
Wireless Network Name...must exactly match your D-Link wireless network name
Enable ethernet clients if you want the port to be active (your D-Link must be compatible with ProxySTA for this to work)
Wireless Security...exact setting of the D-Link network. WEP security causes a lot of issues. Try to use WPA/WPA2 Personal, which is far more secure.
Wireless Password...must match the D-Link network
Click the Music icon to enable AirTunes
Click Update to save settings
Any luck?

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

This Apple support document provides good general information on configuring different types of neworks using multiple AirPort routers.
http://support.apple.com/kb/HT4145
In particular, you would want to focus on the information regarding a "Roaming Network"

Setup Problems with New AirPort Extreme and Dell Desktop XP with ethernet

I have a Dell desktop computer at home with a cisco cable modem connected to Comcast. I am trying to setup a new wireless network using new AirPort extreme so that new iPad can use wireless.
Connections seem to work but when running the AirPort Utility, it doesn't find my base station. The Dell doesn't have wireless. Does the Airport Utility only work via wireless? Or can it work across the ethernet connection?
I'd appreciate anyone's help.
Thanks.

Hello VL Crew. Welcome to the Apple Discussions!
Does the Airport Utility only work via wireless?
No, the AirPort Utility will work whether your computer is connected to the 802.11n AirPort Extreme Base Station (AEBSn) by wire or wireless.

Can I use the Ethernet Port for a computer when it is also used as a wireless network with an Airport Extreme as the access point for the wireless network

Can I use the Ethernet Port of the A1264 Airport Express to connect to the Ethernet port of a computer that does not have wireless capability when the Airport Express is also used on a wireless network with an Airport Extreme 5th generation as the access point for the network?
I have AE 5th gen
looking to buy (from ebay) the AEX A1264
Various computers, printers and hubs for the network
Is this possible to do?

Bob, Thanks for the info. I have read different articles that said yes, but I wanted to make sure before I commit to buy. I have an older A1084 which I could not use the Ethernet port. I know at one point I was able to when I was on 10.4. Now that I am on an Intel processor and 10.8 I am going to have to upgrade some of my Apple wireless hardware.
Thanks Again.

How do I unhide my network which I recently set up with new Airport Extreme?

I recently set up my new Airport Extreme. Then realised my Canon MX 410 was not seeing it on wifi network. I've been told I need to unhide the AE so the printer can see it. However, when I go into Airport Utility it is not giving me the option to unhide. I have tried connecting ethernet cable to it & turning off wifi, but this does not help.. Any ideas people?
Thanks....

I've been told I need to unhide the AE so the printer can see it.
Advice likes this sounds good.....IF.....you previously enabled the option to "hide" your network. Chances are, you would know if you did do this, but if you are not sure, you can check to see if the network really is "hidden".
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the AirPort Extreme icon, then click Edit in the smaller window that appears
Click the Wireless tab at the top of the next window
Click Wireless Options at the bottom of the window
If the network is hidden, you will see a check mark in the box next to Create Hidden Network. If the box is not checked, then your network is not hidden...so there is no way to "unhide" a network that is not hidden in the first place.....and you might want to contact Canon support for help on how to set up your printer.
If you do see that the box is checked, then remove the check mark to "unhide" your network, click Save, then click Update and allow a full minutre for the AirPort Extreme to restart.

Power Mac G3 Pismo with Airport wireless card in Mac OS X 10.4 won't connect to wireless network with newest Airport Extreme Base Station set at WPA Personal/WPA 2 Personal encryption.

My Power Book G3 Pismo with an Airport wireless card running Mac OS X 10.4.11 will not connect to my new Airport
Extreme Base Station using WPA Personal/WPA 2 Person encryption. The Airport firmware is version 9.52. From
posts I've read online at different places indicates the Airport card should support the WPA encryption. Perhaps the problem
is the Base Station is using a combination setting and the fault is in the base station?
Thanks for any suggestions

Perhaps an inexpensive usb wireless adapter would work as well?
This is probably the simplest way to get the G3 connected to the wireless network.
I'll have to read up on getting an express and using it as a wireless bridge as I am unfamiliar with the concept.
The new AirPort Extreme is broadcasting a wireless signal.
A new AirPort Express could be located close to the G3. The Express will pick up the wireless signal from the AirPort Extreme, then provide an Ethernet connection to the G3 though a short Ethernet cable.
This can work very well......IF.....you keep the G3 at a fixed location, since it will always be connected to the AriPort Express using an Ethernet cable.
I do have an old Linksys Wireless G router. I wonder if that would work?
In theory, yes. But it would have to use much older WEP "security", which is easily cracked in minutes using free tools available on the Internet. So, anyone who really wanted to get on the network could do so. It's an option, but not a very good one.

Help with new Airport Extreme

Hello,
I purchased a new Airport Extreme at the Apple store today and have it connected with a new Zoom 5341J. ISP is Comcast. I hooked everything up and I do have a solid connection....however my 2008 MB pro and iPhone 6 are maxing out at 30mbps on wireless. I had over 100 mbps hardwired. Its weird because it stops right at 30mbps during OOKLA speedtest. Something isn't right. I am hooked up to 5 ghz at channel 161.
Any suggestions?

thanks for all of the help!!
Nevermind I figured it out myself. The zoom modem I was using is not compatible to VOIP, so I just went back to my technicolor and put it in bridge mode with the airport extreme and I am now getting 130mbps+ both wired and wireless.
Thanks!

Argh! Trying to Replace Linksys with New Airport Extreme...

Been fighting with this for hours...about ready to take the new Airport Extreme back ...Here's the deal:
I currently have a very wired and wireless 2story home professinally set up with 2 Linksys devices as the primary network and a couple previous generation airport expresses as extenders.   Due to video, audio and other systems the primary router for the network/WAN closet out in the garage needs to remain on the primary Linksys (non wifi) router. I want to replace the Linksys Wifi router (see below) that is puposely set up and has worked for several years as a double NAT config with the new Airport Extreme but i have tried duplicatiing the exact configs from the Linksys router and all the various ways you can use the Airport Express in DHCP/NAT and even in Bridge mode and it still wont work! I've never considered Linksys software easier (and definately more flexible and informative) to use than Apple until this experience! Very frustrating.... I'm being very explicit and using the typical Linksys config profiles below so as to hopefully help you translate this into specific configs i can wrangle into the Airport Extreme to make it work like the
Current Primary Network:
Current WAN Router / + 24 Port Switched LAN Network (for wired ethernet access ports used throughout house) > Linksys BEFSX41 + Linksys 24 port Switch locted in a custom built data /video / audio closet in garage
WAN IP: DHCP
LAN IP: 192.168.1.1
Subnet Mask: 255.255.255.0
Current WiFI Network > Linksys WRT160Nv2 (currently conected to the 24port switch via a hardwired ethernet wall port upstairs in my office)
Internet Connection Type: Static IP
WAN IP: 192.168.1.2
Subnet Mask: 255.255.255.0
LAN IP: 192.168.0.1
Subnet Mask: 255.255.255.0
Per config notes from the network engineer who i worked with to build this network when i built the house
"this allows the 192.168.0.x wifi device to successfully route to the 192.168.1.x wired router (and vice versa)"
My goal is to replace the Linksys WRT160Nv2 with the new Airport Extreme (whose range and ability to reach both upsatirs and outside to the beach is MUCH better) and locate it DOWNSTAIRS and connect it in the same way as the Linksys (via an ethernet port in the living room) to the same switch / router in the data closet.
I have tried to set up the new Airport Extreme to replicate this config several different ways both bridged and not bridged (including telling it to ignore the double NAT warning) with the latest.   I am pretty sure non-bridged is the right way to do it but i seem to lack a config parameter to tell the Airport Extreme to replicate the equivalent of the WRT160Nv2 settings despite trating all the submenues and options on the airport extreme set up / Airport Utility App. Do i have to telnet directly into the Airport Extreme config files to do this natively? Help!
PS - no i cannot / will not put the Airport Extreme in to replace the primary Linksys router in the data closet - there is no way it will fit or that its wifi could penetrate the EMI and insulation of all the other electronics in the data closet out in the garage and get a good connection into the house

The trick on the airport extreme is to change the DHCP .. when you change the DHCP it changes the actual IP of the AE..
So go to the setup and open the dhcp, in the network options and you can select by arrow the first two octets and replace the third.
I just posted info on this in another post..
https://discussions.apple.com/thread/5134560?tstart=30
Does this answer your question, as I am a bit unclear otherwise??
I have to say I do not like using double NAT.. it is becoming worse and worse as the amount of material on the internet that requires interactive connection increases.. you block so much by doing this.. double NAT is an issue .. not just ignore the warning.
There is no reason why you need double NAT.. you should have a single flat network. If you need to keep some things isolated from others the correct way to do it is vlan.. but you will need a better router than the old linksys to do it. And possibly a managed switch. Nowadays a managed 24 port gigabit switch is not a bad price at all.

PROBLEM with new Airport Extreme

i just bought the new airport extreme and what was supposed to be a simple setup process has taken longer than 10 hours!
please help!
i have 3 computers.
2 are macs, they will be using wireless. 1 is a PC, which will be wired to the airport extreme.
the airport extreme is connected to a VOIP router, which is then connected to the DSL router.
i have always used my old airport extreme without issues, but because i want to connect the PC as well, i must ditch the airport express in favour for one with LAN ports. hence, the troublesome airport extreme.
it doesn't work.
none of my computers can recognize the new network. (even though i've established one, with passwords and everything)
the router flashes amber - internet works, but not wireless.
the router periodically flashes green - ironically, nothing works then!!!!
please help!!!
EDIT: DIAGRAM
1. WHEN IT WORKED:
INTERNET --> PROVIDER ROUTER --> VOIP ROUTER --> AIRPORT EXPRESS --> MAC 1, MAC 2 (WIRELESS)
2. WHEN IT DOESN'T WORK:
INTERNET --> PROVIDER ROUTER --> VOIP ROUTER --> AIRPORT EXTREME --> MAC 1, MAC 2 (WIRELESS), PC (WIRED)

It appears to me that you may possibly have sever conflict issues as well as maybe not having the Network confiqured correctly.
I have a 3 story OLD VICTORIAN and I am using the Old Airport Extreme Base and have expierianced NO PROBLEMS at all.
If I may suggest a different approach.
Try to start from scratch.
SHUT EVERYTHING OFF.
Run an ethernet cable from your Internet Service Providers MODEM to the WAN port of the Airport Extreme Base
Set it up DHCP and you want the Airport to distribute IP's
use the Airport setup assistant and Airport Admin Utility.
Using 2 Routers in the mix unless you have ony one the main to distribute the IP's, IF you have 2 Routers and they are both set up to distribute the IP's there is your problem.
The New Airport Extreme Base is far better then the older model and you shouldn't need another router in the mix at all to get the coverage of your entire house.
Take the Netgear clear out and use the Airport Extreme and the Expresses as you had them before. There is a very good possibility that you will need to do evrything one at a time and step by step.
Do not just plug everything in, and turn everything on and expect it to work. Do everthing step by step with all security disabled to begin with.
Be sure when you do your system reset that you start by powering up the MODEM 1st and wait for it to acquire the signal before you power up the Airport Extreme and again you must wait for it to acquire the signal. You can use the LAN Ports for anyyhing you need HARDWIRED. If you don't wait and do things in the proper order you will have problems, I can't stress enough that it must be done in the proper sequence. Have a look at the Paperwork of either the Netgear's Yellow Phamplet or the Booklet that came with the Extreme to bear out what I explained on the sequence.
Don

How to improve upload speeds with new Airport Extreme?

Hi!
Just plugged in a new Airport Extreme to replace a BT HomeHub 3.0. The wi-fi download speeds have generally increased over a wider range in the house but the wi-fi upload speeds have dropped to under 1Mbps.
Speeds to laptop linked via ethernet appear fine (both up & download).
Initially thought that I may have messed-up the set-up but the fact that the wired connection works fine makes me think this is something to do with the Airport settings - a scary thought as I don't really know much about this stuff.
As range was really the reason for getting the AP Extreme I'm contemplating plugging the HomeHub back in and just trying to use the AP to extend the old HHub system rather than setting up a new AP system...
Any suggestions would be most gratefully received!
Thanks

... just a quick note to say that the appears to be resolved after a long telephone call to apple service dept (very patient - very helpful).
In my naivety I had attempted to revert back to using the homehub (3.0) router and connecting the APExtreme into one of the Ethernet LAN ports but this didn't work! So called the apple helpline & we went back to basics until it worked. One point to note that may help anyone finding themselves in a similar position...
I had followed the instruction to reset the APEBS depressing the button first whilst powered then without power and during the unit being reconnected to power supply thinking tha this would do a full restore to factory defaults (effectively undoing all the messing- around I may have done flounderinng through the settings) but it was only when I was directed to do a full reset through the Airport Utility settings [Edit\Advanced\Restore Defaults] that this worked (for me).
Download and upload speeds are now up to 93% of advertised speeds wired, & wireless with some fluctuations which appear to be network delivery related rather than anything to do with the APEBS. It's working well with an APExpress which had been struggling (intermittentlyout of range) which is connected to stereo and Apple TV.
By the way - thanks to other posts regarding importance of not connecting an audio out cable to phono sockets on the stereo (horrible sound quality) using a redundant CD channel it works great.
All-in-all, very happy with it so far.

Need help setting up a network with new Airport Extreme

Similar Messages

Maybe you are looking for