Need help setting up airport express as bridge (Any help is appreciated)

Hello so before my wifi was switched I was able to use my 802.11g airport express as a wifi card for the xbox 360. I then decided to upgrade my main base station from an 802.11g base station to and airport extreme 802.11n. My problem is that my airport express cant extend the airport extreme network to my xbox anymore because they are different 802.11 versions. So can anyone help me configure this so I can get this back? Any help is appreciated.
My Current Setup:
Internet => Airport Extreme 802.11n => Wireless => Airport Express 802.11g (to extend network for xbox)=> Ethernet => Xbox 360
Thanks!

As I said, WDS is a nightmare for most users. Apple hides the settings from users to discourage use of WDS.
I do not recommend that you do this, but have a feeling that you will do this anyway.
I will not be able to help you sort out WDS problems.
On AirPort Utility 5.6, click Manual Setup
Click the Wireless tab below the icons
Hold down the option key on your Mac while you click on the Wireless Mode selection box and the WDS settings will appear
Apple's instructions for WDS are here:
http://support.apple.com/kb/HT4262
Hope this helps. Good luck.

Similar Messages

How to set up Airport Express in Bridge mode for hotel use

Please provide step by step instructions on how to set up Airport Express in Bridge mode for hotel use. I do not have a computer with me, only an iPhone and AEX 802.11n.

+"Please provide step by step instructions on how to set up Airport Express in Bridge mode for hotel use. I do not have a computer with me, only an iPhone and AEX 802.11n."+
AirPort Utility is the application that must be used to setup and make any configuration changes to the AirPort Express. I'm not aware of an "App" for this.
If you could borrow a computer from someone there for 30 minutes or maybe use the computer in the lobby, you could download AirPort Utility and reconfigure your Express. To help with setup, use an ethernet cable from the computer to the Express to help AirPort Utility "see" the Express.
http://support.apple.com/downloads/#airport

I need to connect an Airport Express to an exisitng Wi-Fi Netgear Router. 1) My PC do not detect the Airport Express, 2) AE is flashing amber all the time... Please if someone can help?

I need to connect an Airport Express to an exisitng Wi-Fi Netgear Router. 1) My PC do not detect the Airport Express, 2) AE is flashing amber all the time... Please if someone can help?

Before I bought it I did the same question at the Apple Store, and they told me "You can extend your existing Wi-Fi Signal with Airport Express wireless...
You cannot extend wireless from any brand except another apple router.. the store might have assumed you were using an apple main router. Most people who buy express buy them to extend an extreme or time capsule.
You are correct .. in the setup documents it does say 5.6.1 is adequate to do the setup.. my bad.. !!

Problems Setting-up Airport Express to Play Music thru External Speakers

Hi:
I have an HP dv6500z laptop connected to an HP printer C6280 via LinkSys wireless network using the LinkSys 54G router and PrintServer. It works fine.
I purchased an Apple Airport Express and want to connect it to this network so that I can play songs from within iTunes through external powered speakers wirelessly. The powered speakers are connected to the Airport Express (AE).
The AE is plugged into the AC outlet and the speakers are turned on. The AE is roughly 10 feet away from the laptop/router, just across the room. The AE's
LED is flashing amber (It does not yet recognize the network). I installed the Airport Utility from the enclosed CD, downloaded all patch upgrades and it installed successfully.
Now, how do I tell the Airport Utility to recognize and connect to my existing LinkSys network, so that the AE recognizes it ? The instructions are not clear on this note...they say to run the Airport Utility and then follow the on-screen instructions. The instructions tell you that you will lose your wireless network connection if you continue...and you do if you try.
The same information comes up if you try to do a manual install.
How do I connect the AE to an existing network ? This information seems to be missing. If I go to the AirPort Utility Help and search and search on Setting Up AirPort Express, it tells me the following:
Connect your stereo or powered speakers to your AirPort Express using the mini-jack on the top side of your AirPort Express, and then plug your AirPort Express into a wall outlet.
Open AirPort Utility, located in the Utilities folder in the Applications folder on a computer using Mac OS, and in Start > All Programs > AirPort on a computer using Windows.
Click Music in the toolbar, and select the Enable AirTunes checkbox.
Problem: What Music in What toolbar ? I do not see this...
Enter an iTunes speaker name and password. This is the name displayed in the pop-up menu at the bottom of the iTunes window.
Problem: Where does this information come from
If you're setting up your AirPort Express for the first time, choose Assist Me from the Base Station menu and follow the onscreen instructions.
It seems like something is missing from the setup.
Aaah...Just for the heck of it, I went under Base Station > Assist Me
and told it to continue even though the dialog box said it would change the network.
It displayed a tabbed dialog box where I could configure the AirPort Express, including a tab named Music.
Note:
The following two items are listed in Apple's on-line Help inside of Airport Utility, and on the web, yet I did not see them inside of Airport Utility when trying t oconfigure my AE.
I did not see a checkbox to check, named Enable AirTunes.
I did not see any place for entering the name and password for my speakers.
I followed all of the instructions and things looked like they were going well until I clicked Finish.
Them it said something like it could not save the settings..try again.
Well, I did, but when I brought Airport Utility back up, it kept saying that it could not detect the AE,
and when I went under the Base Station menu, all items were grayed-out, so I couldn't do anything.
Please help... the instructions need to clearer and more detailed.
Thanx, Dale
HP dv 6500z Windows Vista New Airport Express

Hi:
Thanx for your reply.
After several more hours of trial & error over the weekend,
I finally have the Green Light (LED) on the Airport Express.
And it stays green, even if I unplug it from the AC outlet,
and plug it back in later. I have the green light so this
tells me that I have gotten past one hurdle.
OK...in order to get this far, I had the AE wired to the
laptop or LinkSys router via an Ethernet cable. How do
I go about making this a "wireless" connection. LinkSys
told me how to take my laptop from a hardwired connection
to wireless, but it doesn't address the issue when you have
a 3rd party device hardwired that you want to make wireless.
Side Note:
I have not tried this yet, but I found a note on the web that
stated something like this: after getting the green light,
this guy then disconnected the Ethernet cable from the AE,
unplugged the AE from AC power for a few minutes, plugged it
back in to AC power, and voila! ... he was wirelessly on his network.
OK...let's assume that my AE is now on the wireless network.
What type of special settings do I need to make inside of iTunes
in order to get sound to the speakers.
I have my powered speakers recognized by iTunes...I can select them.
But, it appears that something may be blocking my AE from talking to
my network...I keep getting a pop-up box from Symantec saying that it
is detecting a "virus" (for lack of a better term) at the IP address
that I set my AE to. Oh, yes...that's another question...
When manually setting up the AE, I have my router network's IP address
(dotted-quad) in the list of parameter settings, but...near the top of
the list, the Airport Utility software asks for your AE's IP.
Well, what is it ? Nobody has told me ... Where do I get it from ???
Or...do I assign an arbitrary value to it based on the dotted-quad below ?
The router has an IP address of something like 192.168.1.xyz. I know what
the xyz is for the router but, what number do I use here for the AE, or
does it matter as long as it isn't being used by another network device.
My network is static.
So, after using a number not used by my network elsewhere (that I am aware of,
and...inserting a $ (to specify hexadecimal format)in front of my encryption password, NOT the router password (they intermix the naming of these) I finally managed to get the Green Light on the AE. Note: I am using the WEP-64 bit encryption which is also refered to a "40 bit" (No..not hexadecimal..$40 = 64) which is 40-bit to which a random 24 bit is added to give you 64 bit encryption.
To summarize;
I appear to have the AE configured via hardwire (I have the green light).
In iTunes, I can see and select my powered-speakers from the drop-down menu in the lower right corner, but i am s not yet streaming (hearing) the music.
It appears that Symantic may be knocking me off the network, or not letting the AE talk to the laptop/router...I have not yet tried this, but another nugget that I found on this site says to go to System Preferences (where?), click on the Firewalls tab, click Advanced , and uncheck "Block UDP Traffic".
Is this what may be blocking my AE talking to the laptop/router ?
Any help/feedback would be appreciated...Thank you.
I'm getting close...but no cigar (yet).
DaleB

HT4259 Trying to set up airport express to extend my wireless network. Primary base station is a time capsule. Even when I plug in the airport express to mac it cannot find it.

Trying to set up airport express to extend my Wi-Fi network. Primary base station is a time capsule. Tried searching for airport express using Wi-Fi status, no luck. Even tried plugging airport express into iMac, still no luck. Airport express showing solid amber light. Thanks for any help.

Airport express showing solid amber light
Unfortunately, this can mean one of two things:
1) The Express is locked up and will need a Factory Default Reset procedure to try to return the device back to its original default settings so that it can be reconfigured again.
2) The Express is defective. If you cannot get the Express back to a slow, blinking amber light after a Factory Default Reset, the Express will need to be replaced.
Try the Factory Default Reset a few times and report back on your progress.
Resetting an AirPort Base Station or Time Capsule FAQ

Can you guide me step by step in setting up airport express as a wireless extender for an existing Airport extreme network

Can you guide me step by step in setting up airport express 802.11 as a wireless extender for an existing airport extreme network?

Also check out:
Re: Need Help Networking AirPort Exp to Existing AirPort Extreme
Re: How to connect AirPort Express to existing AirPort Extreme Network...

THe Disk of the Time Capsule cannot be written by Time Machine when an Airport Express is bridged to it by Ethernet

Whenever I add an Airport Express in Bridging Mode to the existing WiFi network of the Time Capsule (both connecting to the same GigaBit Ethernet ADSL modem router, Time Machine (and Finder) cannot backup to the Time Capsule Disk.
(Why do I need to add another Airport Express to the same WiFi network? Because I want to use the AirPlay jack on the Airport Express to output audio signals.)
If I unplug the power of the Airport Express, everything back to normal.
What's the problem?

Hello Ivan H
Try using the setup process in the Connecting to an existing Wi-Fi network, exclusively for iTunes music section of the article below and set it up wirelessly as opposed to a wired connection between the two base stations.
Wi-Fi base stations: How to set up and configure AirPort Express for AirPlay and iTunes
http://support.apple.com/kb/HT4587
Regards,
-Norm G.

How to set up Airport Express to extend Buffalo WHR HP 54g wireless router

Contrary to what official Apple policy is, it is possible to use Airport Express as a remote repeater using a Buffalo router.
I sent hours setting up this network and wish to share what I learned
I only wanted to use the Airport Express as a repeater to distribute the internet to the far reaches of the house--no iTunes, no Printer, and I did not bother setting security. If you want to add any of those features please make sure that the basic setup is working as described below. I have no idea how to successfully set up these features. My advice is to search the internet for guidance.
Anyway: how to set up the Buffalo wireless access router to work with Airport Express
Setting up the Buffalo:
From the routers home page of 192.168.11.1, hit the "advanced" box at the top
1.     Go the "Wireless config"   "basic" item. Give name to your network (spaces are allowed), lets call it "WIRENAME" and select wireless channel 1 or 6 or 11. These channels have the least interference and will tend to work when the others do not.
2.     Go the the "repeater" item under Wireless config. . " Enable" repeater/bridge (WDS). Next register the MAC address of the Airport Express. Record both the LAN and Wireless MAC addresses.
That is about it. Your Buffalo system Info page should look like this
Model
WHR-HP-G54 Ver.1.40        (1.0.37-1.08-1.04)
                    AirStation Name              AP001D73DEB2D6                    Operational Mode                Router Mode                    WAN
DHCP
Connection Status
Communicating
Operation
IP Address
myinfo
Subnet Mask
255.255.255.248
Default Gateway
my info(Via DHCP)
DNS1(Primary)
my info (Via DHCP)
DNS2(Secondary)
my info (Via DHCP)
Host Name
my info (Manual Setup)
Domain Name
earthlink.net (Via DHCP)
MTU Size
1500
DHCP Server Address
10.108.48.1
Lease Acquired Time
2006/01/04 12:03:15
Lease Period
2006/01/05 12:03:15
Wired Link
100Base-TX                                (Full-duplex)
MAC Address
00:1D:73:xx:xx:xx
                    LAN
IP Address
192.168.11.1
Subnet Mask
255.255.255.0
DHCP Server
Enabled
MAC Address
your address recorded in the repeater tab
               Wireless(802.11g)
Wireless Status
Enabled
SSID
                                      WIRENAME
Encryption Mode
Not Configured
Wireless Channel
11Channel                 (Manual)
125* High Speed Mode
                             Disabled
MAC Address
your address recorded in the repeater tab
For the Airport express: here is a summary of what the settings are: Start Airport Express Utility and when it comes up
Select "Manual" setup
On the Base station tab: Give Airport Express a name, any name and any password. Do not select the box: Allow setup over the internet with Bonjour
On the wireless tab: Wireless mode: Participate in a WDS network
Network name: the name you gave in the Buffalo router: EG: WIRENAME
Radio mode: 802.11n(802.11b/g compatible)
Channel : the same as you set in the Buffalo
Wireless security: None
WDS tab: WDS mode: WDS remote
Check: allow wireless clients
WDS main: the MAC address of the wireless (not LAN) side of the Buffalo router
Access control tab: MAC address access control: Not enabled
At the top of the control box , click on the Internet icon
     Internet connection: Connection sharing: Off (Bridge Mode)
     TCP/IP: Configure iPV4 : Using DHCP
     I put in the address of the DNS servers listed on the Buffalo System info page above.
At the top of the control box Music Icon: I did not enable AirTunes
Printer icon: did not set this up
Advanced icon: leave every thing alone
That is it. Just do everything as above and your Airport Express will act as a repeater. (And save yourself a couple of days struggle.)
Phil

Many thanks for the info.
In case you were not aware,the following list of Apple WDS compatible devices has appeared on numerous sites and in numerous Internet links and articles regarding this subject:
3com OfficeConnect ADSL Wireless 11g Firewall Router model 3crwdr100a-72 but ONLY with NO encryption
Belkin F5D7230-4 and F5D7231
BT Voyager 2091 or 2100
Buffalo WGR-G54
Linksys WRT54G or WRT54GS (though v4)
Netgear WGR614 v6

Trouble setting up Airport Express and Windows

I am trying to help a friend set up Airport Express to work with her Windows computer. The goal is to use the Airport Express so she can stream iTunes to her stereo system. There is an existing Linksys wireless network. First I tried to connect add the Airport Express to her existing wireless network. I was able to see the base station and I chose to add it to her existing network. I was able to go through all the steps updating the Airport Express. After the base station restarted, the configuration tool couldn't see the base station anymore. In iTunes on her Windows computer, I could see the base station but when I clicked to select the speakers, it wouldn't select.
I reset the Airport Express to factory settings and tried again with the same result.
I reset again and tried using the Airport Express to replace her wireless network and to also stream iTunes. In the configuration app I chose to create a new wireless network. I was able to set up the Airport Express as a wireless network and could connect her Windows laptop to the Internet through the Airport Express. But I had the same problem in iTunes: I could see the speakers in the drop down list, but I couldn't select them.
I've returned everything to how it was (Linksys wireless network).
Can anyone let me know how to make this work?
Thanks

As I mentioned in my post, I followed the directions exactly. I used the same set of directions in the previous post. At the last step of the set up, the Airport Express restarts. After restarting, I got an error saying the utility could not find the base station. I reset the Airport Express to factory settings and went through the steps again and had the exact same result.
I am using an Airport Express at home with a Linksys router and I had no problem setting it up to join my network. The only difference is that I use a Mac at home. The one I am trying to set up for my friend is with a Windows XP machine.
Has anyone ever had this problem?

I just bought a new Motorola modem. Do I need to reconfigure my Airport Express? For some reason we have WiFi even though the amber light is blinking.

I just bought a new Motorola modem. Do I need to reconfigure my Airport Express? For some reason we have WiFi even though the amber light is blinking.

Typically, when changing out networking hardware, it is always a good idea to perform a complete power reset of all of your networking equipment.
I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
Power-up your computer(s).
If the above steps do not solve the problem, start over with step 1 above, but then perform the next steps between steps 1 & 2. above.
Disconnect the AirPort base station from the Internet broadband modem.
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
Continue with step 2 in the first set of steps.
In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

I set up Airport Express as Client, I can no longer connect to my wlan

I set up Airport Express in Client mode so that I could use Airtunes. My Router/modem is a netgear one and I use WPA.
I can no longer connect to my wireless network from my ibook.
If I plug in the ethernet to the router I can. I can also then see from the router that Airport express has connected itself to the router.
So what do I have to do to be able to reconnect to myibook to the WLAN?

Double-check these settings on your iBook:
System Preferences > Network > Show > Network Port Configurations
- Verify that an AirPort option exists. If it does not, click "New" to create one. - Verify that AirPort is "On" (checked)
- Verify that AirPort is at the top of the list. If it isn't, you can drag it to the top.
Systems Preferences > Network > Show > AirPort
AirPort tab
- By default, join: Automatic
TCP/IP tab
- Configure IPv4: Using DHCP
- Configure IPv6: Automatically or Off
Proxies tab
- Configure Proxies: Manually
- Select a proxy server to configure: <All proxies should be unchecked unless you specifically require a proxy for Internet access.>
- Exclude simple hostnames (unchecked)
- Bypass proxy settings for these Hosts & Domains: <leave blank>
- Use Passive FTP Mode (PASV) (checked)

I now have internet thru AT&T Uverse with their wireless router.....do I still need to use my Airport Express for my 2 MACS or can I just unplug it?

I now have internet thru AT&T Uverse with their wireless router.....do I still need to use my Airport Express for my 2 MACS or can I just unplug it?

You can just unplug the express and use the Uverse wireless or ethernet directly to it.

HT1515 do you need to connect the airport express to a router via ethernet or can it do it using wireless?

do you need to connect the airport express to a router via ethernet or can it do it using wireless?

There are 3 Apple routers....AirPort Express, AirPort Extreme and Time Capsule. Details here:
http://www.apple.com/compare-wifi-models/
Do you have one of these products in the living room?
If no, you can only use the AirPort Express by connecting to the router in the living room using an Ethernet cable at all times.

Need to configure older airport express

I had an airport express unused in years just found. I am running Lion on mac laptop. I factory reset the express and try to configure with wifi setup
because Airport utility coul dnot see it
I got this mssage
This version of AirPort Utility doesn’t support this base station. Use AirPort Utility 5.6 to configure or manage this base station. AirPort Utility 5.6 is available at AirPort Service and Support.
When I download 5.6.1 its not compatible with lion and won't install
Is there any hope ?
A way to update the express
I looked to use the current airport utility and use configure other by the IP addres the unit gets from my linsys router
Configure other has field for IP address and password
I know the IP addres but what would be the password after factory defaults reset? Would it even work if I knew the password?
Please advise how to resolve

Found this item and used as described installed just as "replace"
When I opened the airport utility I did not do the request update
saw my old aiport express base station immediately and configured it to join the netowrk.
Worked with no issues
done.
VikingOSX
Splash1111 wrote:
I had an airport express unused in years just found. I am running Lion on mac laptop. I factory reset the express and try to configure with wifi setup
because Airport utility coul dnot see it
I got this mssage
This version of AirPort Utility doesn’t support this base station. Use AirPort Utility 5.6 to configure or manage this base station. AirPort Utility 5.6 is available at AirPort Service and Support.
When I download 5.6.1 its not compatible with lion and won't install
Is there any hope ?
A way to update the express
I looked to use the current airport utility and use configure other by the IP addres the unit gets from my linsys router
Configure other has field for IP address and password
I know the IP addres but what would be the password after factory defaults reset? Would it even work if I knew the password?
Please advise how to resolve
Re: set up airport express in mountain lion
Jan 4, 2013 5:09 AM (in response to andyBall_uk)
Used Pacifist to install just the /Applications/Utilities/Airport Utility v5.6, and not update or overwrite anything else it offered to install.
It now works in Mountain Lion.
Thanks.

Problems setting up AirPort Express Base Station

I'm a real newbie at this, so pardon the ignorance in advance haha.
I just bought a new Airport Express base station. I wanted to be able to stream my music via iTunes to my living room. I'm just having problems getting the aiport utility to recognize the base station. I have the base station plugged in and everything. Right now it is flashing the amber light.
This is my set-up. I have a Netgear WGR614 54MBPS wireless G router connected to my broadband modem. From the router I have it connected to my desktop thats running windows xp pro. The network is up and running just fine. I can connect via any laptop or other device with wifi. Now, how do I get my wireless router to pick up the base station? Do I have to wrong idea here or something? haha. thanks in advance!

In the Airport Utility for your Airport Express, you should set the Airport Express in "client" mode. You might have to connect your Airport Express directly to your router with ethernet cable, while doing this. If you are using encryption, make sure that you enter the encryption number onto the express that your router/access point is using. Again, if you plug the Express directly into the router, you should be able to modify the settings quite easily. Once you unplug the express, it will blink orange for awhile (maybe a minute), so wait a bit.
Good luck.

Need help setting up airport express as bridge (Any help is appreciated)

Similar Messages

Maybe you are looking for