Need help troubleshooting WRT54G internet problem
Recently in order to reconfigure my linksys router WRT54GL, i had to do a factory reset because of password problems. Then i logged in and set it to PPPoE (as usual), and ever since the internet has been completely erratic. I have this far used only the browser and i get the following symptoms:
When i open a new browser session, some pages load, but after, when i load a 3rd completely new page/site it won't load. I might try in that same browser to try another site and it may or may not work.
I have noticed that when i leave it alone and come back after 10 minutes or so and open a new browser session any site that didn't work in the previous session will work, as long as it is one of the 1st sites i load in the newer browser session. edit: actually there are now some sites that worked earlier and now don't even load at all!
Msn messenger appears to function properly, however.
I should point out again, that previous to that initial reset of the router, everything worked perfectly, now it's all messed up. When i plug the pc into the modem directly, it works fine.
Any ideas what could be wrong?
Message Edited by diomedes64 on 12-10-2008 06:36 AM
Looks like the problem is caused by that router, you can test by connecting the computer directly to the router, and see whether the problem persists. Also you can reset the router and configure it again, after that test again.
picoHat
Home Network, Wireless Network and Computer Networking Made Easy
Message Edited by picohat on 12-10-2008 10:48 AM
Similar Messages
-
Need help troubleshooting officejet4630 printing problem
I cannot print from my officejet 4630. I encountered the problem a few days ago and I have been working tirelessly to get this up and running again. The problem first started with my desktop, and the following day I was unable to print with my laptop.
In the laptop:
I have uninstalled and re-installed, I have downloaded print dr. and documents seemed to print sporadically, a half hour after I sent them to the queue.
in the desktop:
I have uninstalled, and I am unable to reinstall. It seems to get stuck at the network check. Ok, so I unplugged my router to see if connectivity was the problem. It's fine. I was able to get signal back to my desktop and my printer quickly. The signal is strong in both devices at all times (mine is the only computer in the house). So what the heck is going on? I've troubleshooted and I arriving at no clear answer. I'm reaching the end of my rope trying to figure this out, please help asap.Hey @mhubbard,
Welcome to the HP Support Forums!
I would like to work with you today with resolving the network communication and printing issues you're experiencing with your HP Officejet 4630 e-All-in-One Printer. I understand that this issue is affecting both your laptop and your desktop. You have also ran the Print and Scan Doctor tools, uninstalled and reinstalled, and powercycled your router to no avail. It is important to note that even though your signal strength for your network is great there is still a chance that your router could be blocking some communication to a printer.
Just so you are aware, when you network a printer there really is no grey area, the printer either works or it doesn't. If the printer doesn't work at all on a network than you may have a defective network card. However, if the printer connects to the network, even if it's an intermittent connection (slow printing, no communication, etc . . . ), it proves that the network card is functioning. Sometimes routers deem the printer as a threat trying to access the network and end up blocking some or all features of the printers network communication. This isn't something that is wrong with the router, it's just doing its job too well.
Now with that being said, I'm going to take you through some troubleshooting steps to get this product up and running consistently for you. Please run through the step-by-step troubleshooting steps below.
Step 1: Powercycle the Network:
I know you have already tried this, but there is a special way this should be done. If you haven't already please run the steps below.
1.First, unplug the power cable to your Router
2.Once your Router is unplugged, turn off your printer
3.Next, shut down your computer
4.After 30 seconds to 1 minutes, plug your Router back in
5.Next, turn on your printer
6.Turn on the computer
After a few moments the internet connection will reestablish itself. Check the internet on your computer and ensure it is working before proceeding.
Step 2: Reset the Winsock:
Please run the following steps on your Desktop computer.
The Network Installation Hangs on the 'Checking Network Environment' Screen
Step 3: Printer Doesn't Maintain Wireless Connection:
Printer Does Not Maintain Wireless Connection
Should the steps in this document fail to resolve your issue than proceed to the next step.
Step 4: Open Router Ports:
There are certain ports on a router that allow wireless communication with the printer for printing and scanning. If you're not sure how to open these ports yourself, please contact the manufacturer of your router to do this for you.
Open: Incoming (UDP) Ports:
137, 138, 161, 427
Open: Outgoing (TCP) Ports:
137, 139, 427, 9100, 9220, 9500
Also, on the router ensure that:
Mac Filtering should be OFF
Firmware updated
Firewall may need to be 'off' for testing
Please let me know if the steps I've provided resolve your wireless communication and printing issues. Good luck!
X-23
I work on behalf of HP
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
Click the "Kudos, Thumbs Up" on the right to say "Thanks" for helping! -
I need help in resolving a problem that prevents me from accessing the iTunes store. Message reads " iTunes cannot contact the iTunes store" and also says that my laptop is no longer authorized to access my account. Help!
Go up to the top of your screen on iTunes and click on 'Store'. Then go down to 'Authorize This Computer'. That should cover part of it unless you've already authorized a bunch of other computers to use your account. If that's the case, you'll have to go to one of those computers and click the button just below it to 'deauthorize your account' from that computer. If you're not able to access the store, check your internet connection to make sure you are connected. Hope this helps.. good luck!
-
Hi everybody, I am in Turkey on a long assignment, I need help solving a big problem on my macbook pro os 10.9.3. The other week my wife visited some website and now we have a redirect virus of some sort, and every other time when we click on a link or anywhere on the page we are redirected to this casino web site, https://casino.7bets10.com/tr/?from=hy9yKXD43jSC-8Oxbw4femNd7ZgqdRLk-dHJpeG9uaXR l. Its the same whether on Chrome or Safari. Does anyone have a solution, thank you!
1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
Don't be put off merely by the seeming complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. All it does is to collect information about the state of the computer. That information goes nowhere unless you choose to share it. However, you should be cautious about running any kind of program (not just a shell script) at the behest of a stranger. If you have doubts, search this site for other discussions in which this procedure has been followed without any report of ill effects. If you can't satisfy yourself that the instructions are safe, don't follow them. Ask for other options.
Here's a summary of what you need to do, if you choose to proceed:
Copy a line of text in this window to the Clipboard.
Paste into the window of another application.
Wait for the test to run. It usually takes a few minutes.
Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
4. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
5. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
6. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts 51 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports ' \*AutoCad \*dropbox \*GoogleDr\* vidinst\* ' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 ` route -n get default|awk '/e:/{print $2}' ` 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB com.apple.AirPortBaseStationAgent 464843899 );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^\([0-9]+\) /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n-\t%s\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' /^ *$|CSConfigDot/d;s/^ */ /;s/[-0-9A-Fa-f]{22,}/UUID/g;s/(ochat)\.[^.]+(\..+)/\1\2/;/Shared/!s/\/Users\/[^/]+/~/g ' ' s/^ +//;5p;6p;8p;12p;' ' {sub(/^ +/,"")};NR==6;NR==13&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: [^EO]|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { if(n<200) print "com.apple.";} ' ' $3~/[0-9]:[0-9]{2}$/ { gsub(/:[0-9:a-f]{14}/,"");} { print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { print "'${p[41]}'";if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$|'${p[41]}'/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:[^:]+//p ' '/root/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/ { n++;print;} END { if(n<1000) print "/System/";} ' '/^\/usr\/lib\/.+dylib$/p' ' /Temp|emac/ { next;} /(etc|Preferences|Launch[AD].+)\// { sub(".(/private)?","");n++;print;} END { print "'${p[41]}'.plist\t'${p[42]}'";if(n<500) print "Launch";} ' ' /\/(Contents\/.+\/Contents|Frameworks)\/|\.wdgt\/.+\.([bw]|plu)/d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| |\n","\\|\\|kMDItem'${p[35]}'=");sub("^...."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[9]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/ { next;} /%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]" "$1;b=b$1;} END { if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"file -b "F|getline T;if(T!~/^(AS.+ (En.+ )?text$|POSIX sh.+ text ex)/) F=F" ("T")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n ...and %s more line(s)\n",l-L);} ' ' /^ +[NP].+ =/h;/^( +D.+[{]|[}])/{ g;s/.+= //p;};' ' /^ +B/{ s/.+= |(-[0-9]+)?\.s.+//g;p;} ' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / / { print "'"${p[28]}"'";exit;};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/\(L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9;} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' 's/0/Off/p' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps sudo\ crontab sudo\ iotop top pkgutil PlistBuddy whoami cksum kextstat launchctl sudo\ launchctl crontab 'sudo defaults read' stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' defaults\ read scutil sudo\ dtrace sudo\ profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil sudo\ lsof test );c2=(com.apple.loginwindow\ LoginHook '-c Print /L*/P*/loginw*' '-c Print L*/P*/*loginit*' '-c Print L*/Saf*/*/E*.plist' '~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 \)' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' '-c Print\ :'${p[35]}' 2>&1' '-c Print\ :Label 2>&1' '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message Req 'bad |Beac|caug|dead[^bl]|FAIL|fail|GPU |hfs: Ru|inval|jnl:|last value [1-9]|n Cause: -|NVDA\(|pagin|proc: t|Roamed|rror|ssert|Thrott|tim(ed? ?|ing )o|WARN' -k Message Rne 'Goog|ksadm|SMC:' -o -k Sender fseventsd -k Message Req 'SL' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cgh] ! -name *ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true \) -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '-L {/{S*/,},}L*/Lau* -type f' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,E}* {/,}L*/{A*d,Ca*/*/Ex,Compon,Ex,In,iTu,Keyb,Mail/B,P*P,Qu*T,Scripti,Sec,Servi,Spo,Widg}* -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,{[lp],sy}*.conf,pam.d/*,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t /S*/L*/Lau*/*t .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers\ "${p[N5]}" -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' -i4TCP:0-1023 com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' '-app Safari WebKitDNSPrefetchingEnabled' );N1=${#c2[@]};for j in {0..8};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents launchd Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls Prefetching );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};';done;A7(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0(){ [[ "$v" ]]&&echo "$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "$s"<<<"$v"`&&C1 1 $1;};for i in 1 2;do for j in 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;A2 0 $((N1+1)) 2;C0;A1 0 $N1 1;C0;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 14 12 14;D22 6 36 13 15;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D22 11 17 17 20;for i in 0 1;do D22 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A2 19 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;A2 4 20 21;B7 6;B2 9;A4 14 7 52 9;B2 10;B6 9 10 4;C3 25;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;D13 24 24 32 31;D13 25 37 32 33;A2 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D13 21 0 32 19;D13 10 42 32 40;D22 29 35 46 39;};D13 14 1 48 42;D12 34 43 53 44;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 26 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 33 34 42 37;B1&&D23 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 20 42 32 41;D13 14 2 48 43;D13 4 5 32 1;D22 4 4 50 0;D13 14 3 49 5;D12 26 48 59 49;B3 4 22 57;A1 26 46 56;B7 22;B3 0 0 58;C3 47;D23 22 9 37 7;A7;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
7. Launch the built-in Terminal application in any of the following ways:
Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
8. If you see an error message in the Terminal window such as "syntax error," enter
exec bash
and press return. Then paste the script again.
9. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
10. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report the results. No harm will be done.
11. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start Time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
12. When you post the results, you might see the message, "You have included content in your post that is not permitted." It means that the forum software has misidentified something in the post as a violation of the rules. If that happens, please post the test results on Pastebin, then post a link here to the page you created.
Note: This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed. -
I need help on the below problem..
Hi All,
I need help on the below problem..
I've 2 Schemas called
1. MAXIMO and DBLink is GQMFOF
2. GQMMGR adn DBLink is MAXFOFNC
Now i would likw to retrive the data from both the schemas,
i.e some columns from WORKORDER table of maximo schema and some columns from ESTIMATE_HEADER table
of GQMMGR schema..
I'm trying to get the data using DB links, but it is giving TABLE/VIEW doesn't exist.
Please help me on this.
Regards,
gr.Does your user has the SELECT privelage granted for accessing those tables?
-
pls i need help for this simple problem of my palm os zire 72. pls share your ideas with me.... i tried to connect my palm os zire72 in my desktop computer using my usb cable but i can't see it in my computer.. my palm has no problem and it works well. the only problem is that, my desktop computer can't find my palm when i tried to connect it using usb cable. is thier any certain driver or installer needed for it so that i can view my files in my palm using the computer. where i can download its driver? is there somebody can help me for this problem? just email me pls at [email protected] i really accept any suggestions for this problem. thanks for your help...
If you are using Windows Vista go to All Programs/Palm and click on the folder and select Hot Sync Manager and then try to sync with the USB cable. If you are using the Windows XP go to Start/Programs/Palm/Hot Sync Manager and then try to sync. If you don’t have the palm folder at all on your PC you have to install it. Here is the link http://kb.palm.com/wps/portal/kb/common/article/33219_en.html that version 4.2.1 will be working for your device Zire 72.
-
I need help with a iMac problem my brother has!
Hello! So my brothers old iMac (around 2-3 years old) would just not start. When i pressed the start button on the back of the computer the screen just turned white with a apple logo in the middle and the typical wheel spinning. We waited for about 30 minutes but still nothing. My friend told me to hold shift+command+r+p and that brings up a menu after a while if i want to restore from time machine, reinstall max os x, get help on the internet or so some stuff with the discs. The last 2 things are not important tho. When i then press "restore from timemachine" or something it starts to search for a backup. After 10 minutes it still hasnt found one. So i went back and clicked "reinstall mac os x" and it showed the disks i was going to install the new mac os x software on.
There was one called "Macintosh HD" and one called "Recovery HD". But they both were locked and i could not install mac os x beacause they were the only 2 disks there. Macintosh HD was about 600GB memory and 150GB free and the other one was only about 600MB. How can i fix this? It would be nice if we could restore the computer back to before because he had some things from school but if it dosnt work we can do a full new mac os x so it is all new and no programs/users on it. I hope you understood what i said because my english is not that good
Its OS x 10.8.4 i think, might be 10.8.2/3 or something xDI suggest verifying that your hard drive is OK. First power off the system, then hold down the Command and R keys to get into the Mac OS X recovery mode. Once you select your language you can run Disk Utility to determine whether your hard drive is functioning correctly. I suggest using the 'Repair Disk' and Repair Disk Permissions' options. If Disk Utility finds problems (SMART errors) then you will need to get them resolved before proceeding. I believe too many SMART errors can lock your drive.
I also suggest reviewing the following Apple website describing the iMac 1TB Seagate Hard Drive Replacement Program to see if your system is affected. The program has been around for quite awhile. According to the document, eligibility may have ended April 12th depending on when you purchased the system, but it's worth checking.
http://www.apple.com/support/imac-harddrive/ -
I need help with a browser problem
I am was given a new iMac G3 (from 2001) which was really never used.I have not yet had any serious problems with it, but really could use some help with a browser problem.
I have 4 different web browsers that needs the macro media flash player update. The browsers I use are internet explorer, iCab, Netscape, and the original Mozilla Firefox.
It would be of great appreciation for the readers of this post to answer my question.
I am also having the problem with installing the plug - ins for the browsers. Thank You For Taking the Time To read This!Hi, rynodino -
As Tom has suggested, plugins need to be installed in the Plug-Ins folder for the browser.
Typically each browser will have its own Plug-Ins folder, usually located in the same folder containing the browser itself. In order for each of several browsers to access the same plugins, the plugins must be replicated and placed in each of the Plug-Ins folders for each of the browsers. The easy way to do that is to hold down the Option key while dragging a plugin to the new location - a copy (not an alias) of the plugin will be generated at the location it is dragged to.
Most plugins will display a Netscape icon regardless of where they are located - this is normal.
It is not unusual for the installer for a plugin to default its install to the Plug-Ins folder for Internet Explorer. So be it. Just replicate the new plugin to the other Plug-Ins folders as needed.
Note that some plugin installs will involve more than one item. For those, be sure to replicate all items for it. Using labels can help identify what is new, what has been most recently added, in a Plug-Ins folder. -
NEED HELP IN SQL HOMEWORK PROBLEMS
I NEED HELP IN MY SQL HOMEWORK PROBLEMS....
I CAN SEND IT VIA EMAIL ATTACHMENT IN MSWORD....Try this:
SELECT SUBSTR( TN,
DECODE(LEVEL, 1, 1, INSTR(TN, '#', 1, LEVEL-1) + 1),
DECODE( INSTR(TN, '#', 1, LEVEL) , 0 ,
LENGTH(TN) + 1, INSTR(TN, '#', 1, LEVEL) )
- DECODE(LEVEL, 1, 1, INSTR(TN, '#', 1, LEVEL-1 ) + 1)
) xxx
FROM (
SELECT '234123#1254343#909823#908232#12345' TN FROM DUAL
CONNECT BY LEVEL <= LENGTH(TN) - LENGTH(REPLACE(TN,'#')) + 1
XXX
234123
1254343
909823
908232
12345
SELECT regexp_substr(tn, '[^#]+', 1, level) xx
FROM (
SELECT '234123#1254343#909823#908232#12345' TN FROM DUAL
CONNECT BY LEVEL <= LENGTH(TN) - LENGTH(REPLACE(TN,'#')) + 1
XX
234123
1254343
909823
908232
12345 -
Need help for access list problem
Cisco 2901 ISR
I need help for my configuration.... although it is working fine but it is not secured cause everybody can access the internet
I want to deny this IP range and permit only TMG server to have internet connection. My DHCP server is the 4500 switch.
Anybody can help?
DENY 10.25.0.1 – 10.25.0.255
10.25.1.1 – 10.25.1.255
Permit only 1 host for Internet
10.25.7.136 255.255.255.192 ------ TMG Server
Using access-list.
( Current configuration )
object-group network IP
description Block_IP
range 10.25.0.2 10.25.0.255
range 10.25.1.2 10.25.1.255
interface GigabitEthernet0/0
ip address 192.168.2.3 255.255.255.0
ip nat inside
ip virtual-reassembly in max-fragments 64 max-reassemblies 256
duplex auto
speed auto
interface GigabitEthernet0/1
description ### ADSL WAN Interface ###
no ip address
pppoe enable group global
pppoe-client dial-pool-number 1
interface ATM0/0/0
no ip address
no atm ilmi-keepalive
interface Dialer1
description ### ADSL WAN Dialer ###
ip address negotiated
ip mtu 1492
ip nat outside
no ip virtual-reassembly in
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication pap callin
ppp pap sent-username xxxxxxx password 7 xxxxxxxxx
ip nat inside source list 101 interface Dialer1 overload
ip route 0.0.0.0 0.0.0.0 Dialer1
ip route 10.25.0.0 255.255.0.0 192.168.2.1
access-list 101 permit ip 10.25.0.0 0.0.255.255 any
access-list 105 deny ip object-group IP any
From the 4500 Catalyst switch
( Current Configuration )
interface GigabitEthernet0/48
no switchport
ip address 192.168.2.1 255.255.255.0 interface GigabitEthernet2/42
ip route 0.0.0.0 0.0.0.0 192.168.2.3Hello,
Host will can't get internet connection
I remove this configuration...... access-list 101 permit ip 10.25.0.0 0.0.255.255 any
and change the configuration .... ip access-list extended 101
5 permit ip host 10.25.7.136 any
In this case I will allow only host 10.25.7.136 but it isn't work.
No internet connection from the TMG Server. -
Please I really need help with this video problem.
Hi!
Please I need help with this app I am trying to make for an Android cellphone and I've been struggling with this for a couple of months.
I have a main flash file (video player.fla) that will load external swf files. This is the main screen.When I click the Sets Anteriores button I want to open another swf file called sets.swf.The app is freezing when I click Sets Anteriores button
Here is the code for this fla file.
import flash.events.MouseEvent;
preloaderBar.visible = false;
var loader:Loader = new Loader();
btHome.enabled = false;
var filme : String = "";
carregaFilme("home.swf");
function carregaFilme(filme : String ) :void
var reqMovie:URLRequest = new URLRequest(filme);
loader.load(reqMovie);
loader.contentLoaderInfo.addEventListener(Event.OPEN,comeco);
loader.contentLoaderInfo.addEventListener(ProgressEvent.PROGRESS,progresso);
loader.contentLoaderInfo.addEventListener(Event.COMPLETE,completo);
palco.addChild(loader);
function comeco(event:Event):void
preloaderBar.visible = true;
preloaderBar.barra.scaleX = 0;
function progresso(e:ProgressEvent):void
var perc:Number = e.bytesLoaded / e.bytesTotal;
preloaderBar.percent.text = Math.ceil(perc*100).toString();
preloaderBar.barra.scaleX = perc;
function completo(e:Event):void
preloaderBar.percent.text = '';
preloaderBar.visible = false;
btHome.addEventListener(MouseEvent.MOUSE_DOWN,onHomeDown);
btHome.addEventListener(MouseEvent.MOUSE_UP,onHomeUp);
btSets.addEventListener(MouseEvent.MOUSE_DOWN,onSetsDown);
btSets.addEventListener(MouseEvent.MOUSE_UP,onSetsUp);
btVivo.addEventListener(MouseEvent.MOUSE_DOWN,onVivoDown);
btVivo.addEventListener(MouseEvent.MOUSE_UP,onVivoUp);
btHome.addEventListener(MouseEvent.CLICK,onHomeClick);
btSets.addEventListener(MouseEvent.CLICK,onSetsClick);
function onSetsClick(Event : MouseEvent) : void
if (filme != "sets.swf")
filme = "sets.swf";
carregaFilme("sets.swf");
function onHomeClick(Event : MouseEvent) : void
if (filme != "home.swf")
filme = "home.swf";
carregaFilme("home.swf");
function onHomeDown(Event : MouseEvent) : void
btHome.y += 1;
function onHomeUp(Event : MouseEvent) : void
btHome.y -= 1;
function onSetsDown(Event : MouseEvent) : void
btSets.y += 1;
function onSetsUp(Event : MouseEvent) : void
btSets.y -= 1;
function onVivoDown(Event : MouseEvent) : void
btVivo.y += 1;
function onVivoUp(Event : MouseEvent) : void
btVivo.y -= 1;
Now this is the sets.fla file:
Here is the code for sets.fla
import flash.utils.Timer;
import flash.events.TimerEvent;
var video:Video;
var nc:NetConnection;
var ns:NetStream;
var t : Timer = new Timer(1000,0);
var meta:Object = new Object();
this.addEventListener(Event.ADDED_TO_STAGE,init);
function init(e:Event):void{
video= new Video(320, 240);
addChild(video);
video.x = 80;
video.y = 100;
nc= new NetConnection();
nc.connect(null);
ns = new NetStream(nc);
ns.addEventListener(NetStatusEvent.NET_STATUS, onStatusEvent);
ns.bufferTime = 1;
ns.client = meta;
video.attachNetStream(ns);
ns.play("http://www.djchambinho.com/videos/segundaquinta.flv");
ns.pause();
t.addEventListener(TimerEvent.TIMER,timeHandler);
t.start();
function onStatusEvent(stat:Object):void
trace(stat.info.code);
meta.onMetaData = function(meta:Object)
trace(meta.duration);
function timeHandler(event : TimerEvent) : void
if (ns.bytesLoaded>0&&ns.bytesLoaded == ns.bytesTotal )
ns.resume();
t.removeEventListener(TimerEvent.TIMER,timeHandler);
t.stop();
The problem is when I test it on my computer it works but when I upload it to my phone it freezes when I click Sets Anteriores button.
Please help me with this problem I dont know what else to do.
thank youMy first guess is you're simply generating an error. You'll always want to load this on your device in quick debugging over USB so you can see any errors you're generating.
Outside that, if you plan on accessing anything inside the SWF you should be loading the SWF into the correct context. Relevant sample code:
var context:LoaderContext = new LoaderContext();
context.securityDomain = SecurityDomain.currentDomain;
context.applicationDomain = ApplicationDomain.currentDomain;
var urlReq:URLRequest = new URLRequest("http://www.[your_domain_here].com/library.swf");
var ldr:Loader = new Loader();
ldr.load(urlReq, context);
More information:
http://help.adobe.com/en_US/ActionScript/3.0_ProgrammingAS3/WS5b3ccc516d4fbf351e63e3d118a9 b90204-7de0.html
If you're doing this on iOS you'll need to stripped SWFs if you plan on using any coding (ABC) inside the files. You mentioned iOS so I won't get into that here, but just incase, here's info on stripping external SWFs:
http://blogs.adobe.com/airodynamics/2013/03/08/external-hosting-of-secondary-swfs-for-air- apps-on-ios/ -
Oracle Instance Failuer Need help to fix the problem
Hi
I am running Oracle9.2 on AIX. The data base got filed due to the following error and I am not getting where to start to dig into the error. The following are the mesg I found in alert log file. But i restarted it its now running But I dont want the same problem to repeat that's why I need assistance to debug the problem. Thanks
Sat Oct 1 21:11:06 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_65536.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Sat Oct 1 21:11:10 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_64730.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Sat Oct 1 21:11:13 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_29256.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Sat Oct 1 21:11:16 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_74036.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Sat Oct 1 21:11:18 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_24036.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Sat Oct 1 21:11:20 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_58880.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Sat Oct 1 21:11:22 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_24038.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Sat Oct 1 21:11:25 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_65544.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Sat Oct 1 21:11:28 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_74044.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Sat Oct 1 21:11:31 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_24050.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Sat Oct 1 21:11:34 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_55086.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Sat Oct 1 21:11:37 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_59506.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Sat Oct 1 21:11:40 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_58894.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Sat Oct 1 21:11:43 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_59508.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Sat Oct 1 21:11:46 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_65552.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Sat Oct 1 21:11:49 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_24056.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Sat Oct 1 21:11:52 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_65556.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Sat Oct 1 21:11:55 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_64746.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Sat Oct 1 21:11:58 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_74056.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Sat Oct 1 21:12:01 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_55098.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Sat Oct 1 21:12:04 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_74058.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Sat Oct 1 21:12:07 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_59520.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Mon Oct 3 10:25:56 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_23834.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Mon Oct 3 10:27:32 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_38114.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Mon Oct 3 10:28:29 2005
Starting ORACLE instance (normal)
Mon Oct 3 10:29:03 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_65696.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Mon Oct 3 10:29:24 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_54902.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Mon Oct 3 10:31:32 2005
Starting ORACLE instance (normal)
Mon Oct 3 10:31:33 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_55050.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
Mon Oct 3 10:32:07 2005
Shutting down instance: further logons disabled
Shutting down instance (immediate)
License high water mark = 26
All dispatchers and shared servers shutdown
Mon Oct 3 10:32:11 2005
ALTER DATABASE CLOSE NORMAL
Mon Oct 3 10:32:11 2005
SMON: disabling tx recovery
SMON: disabling cache recovery
Mon Oct 3 10:32:11 2005
Shutting down archive processes
Archiving is disabled
Mon Oct 3 10:32:11 2005
ARCH shutting down
ARC0: Archival stopped
Mon Oct 3 10:32:11 2005
ARCH shutting down
ARC1: Archival stopped
Mon Oct 3 10:32:12 2005
Thread 1 closed at log sequence 4026
Successful close of redo thread 1
Mon Oct 3 10:32:18 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_74172.trc:
ORA-00600: internal error code, arguments: [17175], [255], [], [], [], [], [], []
Mon Oct 3 10:32:19 2005
Errors in file /oracle/ABBA1/system/dump/udump/ABBA1_ora_74172.trc:
ORA-07445: exception encountered: core dump [] [] [] [] [] []
ORA-00600: internal error code, arguments: [17175], [255], [], [], [], [], [], []
Mon Oct 3 10:32:29 2005
Errors in file /oracle/ABBA1/system/dump/bdump/ABBA1_pmon_32534.trc:
ORA-00600: internal error code, arguments: [17175], [255], [], [], [], [], [], []
Mon Oct 3 10:32:29 2005
Errors in file /oracle/ABBA1/system/dump/bdump/ABBA1_pmon_32534.trc:
ORA-00600: internal error code, arguments: [17175], [255], [], [], [], [], [], []
Mon Oct 3 10:32:29 2005
PMON: terminating instance due to error 600
Instance terminated by PMON, pid = 32534
Mon Oct 3 10:33:46 2005
Starting ORACLE instance (normal)
LICENSE_MAX_SESSION = 0
LICENSE_SESSIONS_WARNING = 0
SCN scheme 3
Using log_archive_dest parameter default value
LICENSE_MAX_USERS = 0
SYS auditing is disabled
Starting up ORACLE RDBMS Version: 9.2.0.5.0.
System parameters with non-default values:
processes = 150
timed_statistics = TRUE
shared_pool_size = 117440512
large_pool_size = 16777216
java_pool_size = 117440512
control_files = /oracle/ABBA1/system/control01.ctl, /oracle/ABBA1/system/control02.ctl, /oracle/ABBA1/system/control03.ctl
db_block_size = 16384
db_cache_size = 318767104
compatible = 9.2.0.0.0
log_archive_start = TRUE
log_archive_dest_1 = LOCATION=/oracle/ABBA1/archive
log_archive_format = ABBA1_%T_%S.ARC
db_file_multiblock_read_count= 32
fast_start_mttr_target = 300
undo_management = AUTO
undo_tablespace = UNDOTBS1
undo_retention = 10800
remote_login_passwordfile= EXCLUSIVE
db_domain =
instance_name = oracle/ABBA1
dispatchers = (PROTOCOL=TCP) (SERVICE=oracle/ABBA1XDB)
job_queue_processes = 10
hash_join_enabled = TRUE
hash_area_size = 1048576
background_dump_dest = /oracle/ABBA1/system/dump/bdump
user_dump_dest = /oracle/ABBA1/system/dump/udump
core_dump_dest = /oracle/ABBA1/system/dump/cdump
sort_area_size = 1048576
db_name = ABBA1
open_cursors = 300
star_transformation_enabled= TRUE
query_rewrite_enabled = TRUE
pga_aggregate_target = 314572800
aq_tm_processes = 1
PMON started with pid=2
DBW0 started with pid=3
LGWR started with pid=4
CKPT started with pid=5
SMON started with pid=6
RECO started with pid=7
CJQ0 started with pid=8
QMN0 started with pid=9
Mon Oct 3 10:33:48 2005
starting up 1 shared server(s) ...
starting up 1 dispatcher(s) for network address '(ADDRESS=(PARTIAL=YES)(PROTOCOL=TCP))'...
ARCH: STARTING ARCH PROCESSES
ARC0 started with pid=12
ARC0: Archival started
ARC1 started with pid=13
ARC1: Archival started
Mon Oct 3 10:33:49 2005
ARCH: STARTING ARCH PROCESSES COMPLETE
Mon Oct 3 10:33:49 2005
ARC0: Thread not mounted
Mon Oct 3 10:33:49 2005
ARC1: Thread not mounted
Mon Oct 3 10:33:49 2005
/* OracleOEM */ ALTER DATABASE MOUNT
Mon Oct 3 10:33:53 2005
Successful mount of redo thread 1, with mount id 1053693133
Mon Oct 3 10:33:53 2005
Database mounted in Exclusive Mode.
Completed: /* OracleOEM */ ALTER DATABASE MOUNT
Mon Oct 3 10:33:53 2005
/* OracleOEM */ ALTER DATABASE OPEN
Mon Oct 3 10:33:53 2005
LGWR: Primary database is in CLUSTER CONSISTENT mode
Thread 1 opened at log sequence 4026
Current log# 2 seq# 4026 mem# 0: /oracle/ABBA1/redo2/redo2_A.dbf
Current log# 2 seq# 4026 mem# 1: /oracle/ABBA1/redocopy/redo2_B.dbf
Successful open of redo thread 1
Mon Oct 3 10:33:54 2005
SMON: enabling cache recovery
Mon Oct 3 10:33:54 2005
Undo Segment 1 Onlined
Undo Segment 2 Onlined
Undo Segment 3 Onlined
Undo Segment 4 Onlined
Undo Segment 5 Onlined
Undo Segment 6 Onlined
Undo Segment 7 Onlined
Undo Segment 8 Onlined
Undo Segment 9 Onlined
Undo Segment 10 Onlined
Successfully onlined Undo Tablespace 1.
Mon Oct 3 10:33:54 2005
SMON: enabling tx recovery
Mon Oct 3 10:33:54 2005
Database Characterset is WE8ISO8859P1
replication_dependency_tracking turned off (no async multimaster replication found)
Completed: /* OracleOEM */ ALTER DATABASE OPEN
Mon Oct 3 10:34:17 2005
ORA-00130: invalid listener address '(ADDRESS=(PROTOCOL=TCP)(HOST=plpar00)(PORT=1521))'
Mon Oct 3 10:34:35 2005
Shutting down instance: further logons disabled
Shutting down instance (immediate)
License high water mark = 5
Waiting for dispatcher 'D000' to shutdown
All dispatchers and shared servers shutdown
Mon Oct 3 10:34:38 2005
ALTER DATABASE CLOSE NORMAL
Mon Oct 3 10:34:39 2005
SMON: disabling tx recovery
SMON: disabling cache recovery
Mon Oct 3 10:34:39 2005
Shutting down archive processes
Archiving is disabled
Mon Oct 3 10:34:39 2005
ARCH shutting down
ARC0: Archival stopped
Mon Oct 3 10:34:39 2005
ARCH shutting down
ARC1: Archival stopped
Mon Oct 3 10:34:39 2005
Thread 1 closed at log sequence 4026
Successful close of redo thread 1
Mon Oct 3 10:34:39 2005
Completed: ALTER DATABASE CLOSE NORMAL
Mon Oct 3 10:34:39 2005
ALTER DATABASE DISMOUNT
Completed: ALTER DATABASE DISMOUNT
ARCH: Archiving is disabled
Shutting down archive processes
Archiving is disabled
Archive process shutdown avoided: 0 active
ARCH: Archiving is disabled
Shutting down archive processes
Archiving is disabled
Archive process shutdown avoided: 0 active
Mon Oct 3 10:34:49 2005
Starting ORACLE instance (normal)
LICENSE_MAX_SESSION = 0
LICENSE_SESSIONS_WARNING = 0
SCN scheme 3
LICENSE_MAX_USERS = 0
SYS auditing is disabled
Starting up ORACLE RDBMS Version: 9.2.0.5.0.
System parameters with non-default values:
processes = 150
timed_statistics = TRUE
shared_pool_size = 117440512
large_pool_size = 16777216
java_pool_size = 117440512
control_files = /oracle/ABBA1/system/control01.ctl, /oracle/ABBA1/system/control02.ctl, /oracle/ABBA1/system/control03.ctl
db_block_size = 16384
db_cache_size = 318767104
compatible = 9.2.0.0.0
log_archive_start = TRUE
log_archive_dest = /oracle/ABBA1/archive
log_archive_format = ABBA1_%T_%S.ARC
db_file_multiblock_read_count= 32
fast_start_mttr_target = 300
undo_management = AUTO
undo_tablespace = UNDOTBS1
undo_retention = 10800
remote_login_passwordfile= EXCLUSIVE
db_domain =
instance_name = oracle/ABBA1
dispatchers = (PROTOCOL=TCP) (SERVICE=oracle/ABBA1XDB)
job_queue_processes = 10
hash_join_enabled = TRUE
hash_area_size = 1048576
background_dump_dest = /oracle/ABBA1/system/dump/bdump
user_dump_dest = /oracle/ABBA1/system/dump/udump
core_dump_dest = /oracle/ABBA1/system/dump/cdump
sort_area_size = 1048576
db_name = ABBA1
open_cursors = 300
star_transformation_enabled= TRUE
query_rewrite_enabled = TRUE
pga_aggregate_target = 314572800
aq_tm_processes = 1
PMON started with pid=2
DBW0 started with pid=3
LGWR started with pid=4
CKPT started with pid=5
SMON started with pid=6
RECO started with pid=7
CJQ0 started with pid=8
QMN0 started with pid=9
Mon Oct 3 10:34:49 2005
I need assistance in this regard
ThanksIt will help if you have a look at Note:211909.1 in Metalink to understand why ORA-07445
Then have a look at the content of the trace files. e.g /oracle/ABBA1/system/dump/udump/ABBA1_ora_65536.trc to see if you can pick anything from the 'Current SQL statement' you will see in it (get help from Note:154170.1). This will at least give you an idea what SQL is causing the problem.
If they are your own application SQLs, then try to see if your team can fix the code. If they are System related or you cannot figure out what it is (even if it is from your own SQLs), I would suggest log a TAR with Oracle Support. -
I need help with the following book problem...could someone write this code for me?? Thanks!!
First design and implement a class called PairOfDice, composed of two six-sided Die objects. Using the PairOfDice class, design and implement a class to play a game called Pig. In this game, the user competes against the computer. On each turn, the current player rolls a pair of dice and accumulates points. The goal is to reach 100 points before your opponent does. If, on any turn, the player rolls a 1, all points accumulated for that round are forfeited and control of the dice moves to the other player. If the player rolls two 1s in one turn, the player loses all points accumulated thus far in the game and loses control of the dice. The player may voluntarily turn over the dice after each roll. Therefore the player must decide to either roll again (be a pig) and risk losing points, or relinquish control of the dice, possibly allowing the other player to win. Implement the computer player such that it always relinquishes the dice after accumulating 20 or more points in any given round.
I realize this is a long code, so it would be greatly appreciated to anyone who writes this one for me, or can at least give me any parts of it. I honestly have no clue how to do this because our professor is a dumbass and just expects us to know how to do this...he doesn't teach us this stuff...don't ask. Anyways, thanks for taking the time to read this and I hope someone helps out!! Thank you in advance to anyone who does!!!Nasty comments? It's not a matter of not liking you, it's a matter of responding to the
"I'ts everyone else's fault but mine" attitude of your post.
If you are genuine, the program is very easy to write, so, your Professor is correct when he said you should
be able to do it. I'm still very much in the beginner category at java, and it took me only 20 mins to write
(+5 mins to design it on paper). 2 classes in one file < 100 lines. Most of the regulars here would do it in half the time / half the lines.
All of the clues are in the description, break them down into their various if / else conditions. Write it down on paper.
Have a go. Try to achieve something. Post what you've tried, no-one will laugh at you, and you will be
pleasanty surprised at the level of help you will get when you've "obviously" made some effort.
Again, have a go. If you don't like problem-solving, then you don't like programming. So, you gotta ask
yourself - "what am I doin' here?" -
I need help on This SQL problem ASAP :)
Hi All,
I need help on this....
I have a table...
Say table name: one
with these values
premnum status
1234 C
1234 F
1234 P
1234 F
5678 C
5678 F
5678 P
9112 C
9112 F
9112 P
9112 F
3456 C
3456 F
3456 P
7890 C
7890 P
7890 F
Now, I want to output only those premnum with status = 'C' and those premnum with Status 'F' having a count > 1 (with two status = 'F')
So the output would be something like this
premnum status
1234 C
1234 F
1234 F
5678 C
9112 C
9112 F
9112 F
3456 C
7890 C
I really need help on this asap...
I need the SQL statement on this....
Thank you in advance. :)
Edited by: 804697 on Oct 23, 2010 9:45 PMHi,
you can use the following query.
CREATE TABLE PREM_TEST ( premnum NUMBER , STATUS VARCHAR2(1));
INSERT INTO PREM_TEST VALUES(1234 ,'C');
INSERT INTO PREM_TEST VALUES(1234 ,'F');
INSERT INTO PREM_TEST VALUES(1234 ,'P');
INSERT INTO PREM_TEST VALUES(1234 ,'F');
INSERT INTO PREM_TEST VALUES(5678 ,'C');
INSERT INTO PREM_TEST VALUES(5678 ,'F');
INSERT INTO PREM_TEST VALUES(5678 ,'P');
INSERT INTO PREM_TEST VALUES(9112 ,'C');
INSERT INTO PREM_TEST VALUES(9112 ,'F');
INSERT INTO PREM_TEST VALUES(9112 ,'P');
INSERT INTO PREM_TEST VALUES(9112 ,'F');
INSERT INTO PREM_TEST VALUES(3456 ,'C');
INSERT INTO PREM_TEST VALUES(3456 ,'F');
INSERT INTO PREM_TEST VALUES(3456 ,'P');
INSERT INTO PREM_TEST VALUES(7890 ,'C');
INSERT INTO PREM_TEST VALUES(7890 ,'P');
INSERT INTO PREM_TEST VALUES(7890 ,'F');
SELECT PREMNUM , STATUS
FROM PREM_TEST
WHERE STATUS = 'C'
OR (PREMNUM , STATUS ) IN ( SELECT PREMNUM , STATUS
FROM PREM_TEST
WHERE STATUS = 'F'
GROUP BY PREMNUM , STATUS
HAVING COUNT(*) > 1
PREMNUM S
1234 C
1234 F
1234 F
5678 C
9112 C
9112 F
9112 F
3456 C
7890 C
9 rows selected. -
Need Help In Solving Positioning Problem
Hi Guys,
I have a 3 X 3 grid of JLabels of images. I constructed the grid using the grid layout.
I would like to move a round object which represents a car and place that object in a particular cell. So the grid will be like a background.
My questions are these:
1) How can i position this object in a specific cell based on the rows and column values? for instance if i want to put the object in [1][0].
2) How do i move this object to a different cell using the rows and column values. for instance if i want to move the object in [1][0] to [2][1]
Thank you all for your helpThis question has nothing to do with Java 2D. I've removed the second thread you started in that forum.
Thank you for providing a link to this thread in the cross post.
db
kap wrote:
Hi Guys,
I have posted a question in the Java Programming forum. This is the link :
[positioning object|http://forums.sun.com/thread.jspa?threadID=5447680&tstart=0]
I added the link to avoid double posts
I am asking if someone can help me out because i need an urgent help. Some people have giving some ideas but i don't understand what they mean.
Need help in solving it.
Thanks.
Edited by: kap on Aug 14, 2010 6:59 PM
Maybe you are looking for
-
Hp pavilion dv6 recovery system with win 7 dvd image not found
Hello everyone, I have a hp pavilion dv6 I going to restore the operating system win 7 that I previously saved in an image of the system in 2 DVDs. I need to restore the entire computer because I do not want to lose all installations made within a ye
-
Open Ibook PDF's with adobe reader
How do I open a PDF document from the Ibooks library with adobe reader, so I can use all the tools like the highlighter?
-
NI 6602 measure quadrature encoder with two signal edge sepearation
Is it possible to improve the position measurement for X4 encoders, that the measurement starts at start trigger and stops at the stop trigger signal like the normal two signal edge seperation measurments. Everything I tried don't works. Does anyone
-
For some reason my computer fails to boot from scsi cdrom, is there a bootdisk for Solaris x86? I have a Tekram DC-390F SCSI adapter and Pioneer DR-U24X CDROM-drive.
-
Why can't i download any toolbars to firefox 5?
I want to download the Yahoo toolbar onto firefox...Why won't it let me? and why can't i get the firefox 4 back? Nothing wants to work in the "UPDATED" version of Firefox....Some upgrade!!! PLEASE GET THIS PROBLEM SOLVED SOON!!!!I want to download a