Need Help: TS130 Server and Windows Server 2008 R2 64 Bit Problems

I have 2 TS 130 Lenovo Servers with Xeon 3.2 Ghz CPUs and 16GB of memory. Installing ANY version of Windows 64 Bit after a couple of reboots will cause the system to blue screen. Once it blue screens it is impossible to get back into Windows.
Get this. Installing ANY version of Windows 32 bit works just fine on either machine. I have swapped out ram, hard drives, raid on raid off, updated BIOS etc and the same exact issue on both machines. I have swapped out media thinking maybe it was just a bad disk, but after 3 copies of Server 2008 R2 64 and 2 copies of Windows 7 Ultimate 64 and 3 copies of Windows 7 Professional 64 bit and THEN the same problem occurring over and over on BOTH servers.. well needless to say I am pulling mu hair out. These are ALL OEM copies by the way not burned copies.
I called Lenovo Thinkserver support as we are a partner, and their only suggestion was changing some legacy settings in the BIOS which of course has done nothing. I have changed every setting in the BIOS that I feel it could possibly be and still no joy.
Thinking it MAY have been a video problem, I have even went so far as to add new video cards to both machines and the problem still exists on both machines. All drivers are latest versions, and I am getting tired of getting everything setup, and then BAM BSOD.. I have been a tech for 25 years, and I have NEVER seen this issue on any machine ever..
As far as the BSODs, one time it will be the language pack error, next time something else, and the next time something else.. no way to nail down the problem.
I KNOW its a machine error, especially when 32 bit runs fine on either machine, but what it is I have no clue.
I am hopeful someone here has had the same issue and can tell me what they may have done to solve the problem. It is absolutely driving me up the wall....
Thanks in advance for ANY help or suggestions.
Mike at Mitek Computers

Never mind.. FINALLY found the problem. Even though I swapped out media etc as far as Server 2008 went, I always used the same COA key.. guess what... English media and Japanese key.... snafu on our OEM vendors end I suppose.
Anyway I was issued a new product/virtual key through Microsoft and it resolved the issue.... stupidest thing I ever saw...
Mike at Mitek

Similar Messages

Windows server 2012 as primary DC and DNS server and windows server 2003 as secondary DC and DNS

Migration from windows server 2003 AD DC and DNS server to windows server 2012 R2,
Cannot I set up Windows server 2012 R2 as primary DC and DNS , windows server 2003 as secondary DC and DNS ? (for backup server when server 2012 fail, user can continue to login and access internet services)

You can mix both as long as your Forest and Domain Functional level are Windows Server 2003. However, I would like to bring your attention to this blog about known problems when mixing DCs with Windows Server 2003 and 2012 R2 OS:
http://blogs.technet.com/b/askds/archive/2014/07/23/it-turns-out-that-weird-things-can-happen-when-you-mix-windows-server-2003-and-windows-server-2012-r2-domain-controllers.aspx
This posting is provided AS IS with no warranties or guarantees , and confers no rights.
Ahmed MALEK
My Website Link
My Linkedin Profile
My MVP Profile

Need Help Connecting To My Windows Server Machine From My Linux Machine (What Program To Use)

My name is Daniel, and I was wondering what program I could use to connect to my Windows Server R2 2012 Computer from my linux laptop. My laptop has the newest version of linux mint mate. I have tried nomachine with no success (but I could have been using
it wrong I do not really know how). So if anyone could help me out that would be great. Thank You.
P.S: Sorry for the weird Forum Category there is not really a category for this.

ok so i think that worked but i ran into another problem; what password should i use? i changed my sql server 2008 username/password and it didn't work. i also tried my windows 7 username/password and it didn't work also.
EDIT: managed to get it working, all good! thanks a lot.
Edited by: 1008695 on May 30, 2013 7:09 AM

Terminal Server and Windows Server 2008 R2

I currently have a Windows Server 2003 R2 (32 bit) running Terminal
Services. I am currently running ZCM 10.3.3. But this Windows Server
is still using the remnants of my ZfD7 install to manage DLU. I need
to replace this server with Server 2008 R2 SP1 (64 bit). Will ZCM
10.3.3 work with this version? My main concern is controlling DLU
when the users login via Terminal Services.
Thanks,
Ken

Lindsey,
It appears that in the past few days you have not received a response to your
posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Visit http://support.novell.com and search the knowledgebase and/or check all
the other self support options and support programs available.
- You could also try posting your message again. Make sure it is posted in the
correct newsgroup. (http://forums.novell.com)
Be sure to read the forum FAQ about what to expect in the way of responses:
http://forums.novell.com/faq.php
If this is a reply to a duplicate posting, please ignore and accept our apologies
and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://forums.novell.com/

List of OOTB Reports for SQL Server and Windows Server

Hi,
I am struggling to find a list of OTB reports from Operations Manager for SQL and Windows. Ideally I need the name of the reports and a list of counters that they report on.
Can anybody give me an idea where I can find this?
Thanks,
Pete
Peter Carter http://sqlserverdownanddirty.blogspot.com/

Hi Pete,
I don't believe that there are any Windows or SQL Server specific reports out of the box from SCOM.
However, when you import the Windows (either Server or Client, unsure which you are referring to) and/or the SQL Server Management Packs, within the documentation it will tell you the reports that will also be imported and thus available.

Need Help with iTunes and Windows 7

Hi,
I recently purchased a new Dell laptop and tried to install iTunes for my iPod and iPhone. The first time I tried it out it ran smooth as anything, but if I'm connected to the net things start to go downhill. At my flat in University (no internet connect) it ran fine, but the second I went to the University computer room with my laptop, iTunes wouldn't open.
I have uninstalled and re-installed several times now, but obviously dont want to have to do this again and again...
Can anyone please help?
Thank you in advance
Dan

but the second I went to the University computer room with my laptop, iTunes wouldn't open.
What security software are you running on the PC, Dan? (Firewall, antivirus, antispyware?)

Cisco NAC 4.8 and Windows Server 2008 Enterprise 64bit SSO

Hi,
     I try to setup SSO on Cisco NAC 4.8 and Windows Server 2008 Enterprise 64bit, but I can't start Active Directory SSO Service that show error follow below. I saw this error " KDC has no support for encryption type (14)" . Could anyone help me to troubleshoot this problem?
FQDN: active.test.com
Domain Name : test.com
User : ccasso
2011-02-05 12:00:30.225 +0700 WARN com.perfigo.wlan.jmx.adsso.GSSServer
- Server was not running ...
2011-02-05 12:00:30.225 +0700 INFO com.perfigo.wlan.jmx.adsso.GSSServer
- Server starting server ...
2011-02-05 12:00:30.225 +0700 INFO com.perfigo.wlan.jmx.adsso.GSSServer
- Server is now running ...
2011-02-05 12:00:30.225 +0700 INFO com.perfigo.wlan.jmx.adsso.GSSServer
- GSSServer - SPN : [ccasso/[email protected]]
2011-02-05 12:00:30.225 +0700 INFO com.perfigo.wlan.jmx.adsso.GSSServer
- GSSServer - building kdc list for domain active.test.com
2011-02-05 12:00:40.224 +0700 INFO com.perfigo.wlan.jmx.adsso.GSSServer
- GSSServer - done building kdc list for domain active.test.com
2011-02-05 12:00:40.224 +0700 INFO com.perfigo.wlan.jmx.adsso.GSSServer
- GSSServer - KDC(s) :[10.0.240.100]
2011-02-05 12:00:40.224 +0700 INFO com.perfigo.wlan.jmx.adsso.GSSServer
- GSSServer - writeKrbFile: writing to file ../conf/krb.txt
2011-02-05 12:00:40.224 +0700 INFO com.perfigo.wlan.jmx.adsso.GSSServer
- GSSServer - writeKrbFile: wrote to file ../conf/krb.txt
2011-02-05 12:00:40.224 +0700 INFO com.perfigo.wlan.jmx.adsso.GSSServer
- GSSServer - creating login context ...
2011-02-05 12:00:40.224 +0700 INFO com.perfigo.wlan.jmx.adsso.GSSServer
- GSSServer - created login context ...javax.security.auth.login.LoginCon
text@5ad7b2
2011-02-05 12:00:40.239 +0700 ERROR com.perfigo.wlan.jmx.adsso.GSSServer
- Unable to start server ... KDC has no support for encryption type (14)
2011-02-05 12:00:50.244 +0700 INFO com.perfigo.wlan.jmx.adsso.GSSServer
- Notifying GSSServer status Stopped
2011-02-05 12:00:50.244 +0700 INFO com.perfigo.wlan.jmx.adsso.GSSServer
- server is exiting .

Hi,
This error means that your DC does not support the encryption method the ACS wants to use.
Usually this happens when you run 2008 Server with 2003 functionality...
You will need to run ktpass.exe according to the DC you are running:
http://www.cisco.com/en/US/docs/security/nac/appliance/configuration_guide/48/cas/s_adsso.html#wp1277452.
For Windows 2008 Server at 2003 Server functional level:
ktpass -princ newadsso/[adserver.][email protected] -mapuser newadsso -pass
PasswordText -out c:\newadsso.keytab -ptype KRB5_NT_PRINCIPAL
HTH,
Tiago
If this helps you and/or answers your question please mark the question as "answered" and/or rate it, so other users can easily find it.

Advice needed on installing CA on Windows Server 2008 for CUPS Calendar Integration

Hi,
I am trying to configure CUPS 8.0 to connect to Exchange 2008 to retrieve calendar information as detailed in the integration note at the link below:
http://www.cisco.com/en/US/docs/voice_ip_comm/cups/8_0/english/integration_notes/ExchInt.html
I have successfully completed everything up to the section Installing the CA on Windows Server      2008 but am now running into problems.
When I run the Role Services Wizard I get options to install Certificate Authority and Certificate Authority Web Enrollment but not Online Responder.
Can anyone advise why this would be the case?
It may or may not be relevant but the server that the customer has told me to install the CA on is a domain controller - could this be the issue?

A bit more information - below is some of the output generated by the Windows systeminfo cli command.
Host Name:                 DOMDAT02
OS Name:                   Microsoft® Windows Server® 2008 Standard
OS Version:                6.0.6001 Service Pack 1 Build 6001
OS Manufacturer:           Microsoft Corporation
OS Configuration:          Primary Domain Controller
OS Build Type:             Multiprocessor Free
Registered Owner:          V2C
Registered Organization:   V2C
Product ID:                55041-339-2169613-76816
Original Install Date:     25/01/2009, 18:29:39
System Boot Time:          11/06/2011, 08:50:34
System Manufacturer:       VMware, Inc.
System Model:              VMware Virtual Platform
System Type:               X86-based PC
Processor(s):              1 Processor(s) Installed.
                           [01]: x64 Family 6 Model 23 Stepping 10 Genuine ~2494 Mhz
BIOS Version:              Phoenix Technologies LTD 6.00, 22/09/2009
Windows Directory:         C:\Windows
System Directory:          C:\Windows\system32
Boot Device:               \Device\HarddiskVolume1
System Locale:             en-gb;English (United Kingdom)
Input Locale:              en-gb;English (United Kingdom)
Time Zone:                 (GMT) Greenwich Mean Time : Dublin, Edinburgh,, London
The server is running Windows Server 2008 Standard and according to the Microsoft doc at the link below this does not support the Online Responder service.
http://technet.microsoft.com/en-us/library/cc772393(WS.10).aspx
Could the problem be that I need a server running Windows Server 2008 Enterprise?

Lms 3.2 and window server 2008 r2 standard

we have bought lms 3.2 and window server 2008 r2 standard. Now we know, it cant be used togetther
Could we upgrade to lms 4.0.1 ? If so, how can we do ?
thank you.
Duyen.

Correct, LMS 3.2 is not supported on Windows 2008 R2. You can upgrade to LMS 4.0 (which is supported on R2), but that is not a free upgrade from LMS 3.x. You can, however, download a free 90-day eval of LMS 4.0 from http://www.cisco.com/go/nmsevals .
It sounds like you need to contact your reseller or account manager to see what they can do. If you just purchased LMS 3.2, you may be able to get a free or discounted upgrade to 4.0.

Lms 3.2 and window server 2008 standard: License Server/Daemon Manager is down

LMS 3.2 and window server 2008 standard, get error when we try
Khi truy nhập vào menu chức năng:
License Server/Daemon Manager is down. Please check license.log for more information.
access licensing:
Error communicating with License Server. License Server may be down. Please start the License Server, then refresh the page.
Lincense.txt is file log of LMS
Must I have to active window server 2008 first ?
thank you very much ?

Hi ,
--Add the Casuser to the Administrator Group
and then reset the casuser password:
1. Go to CSCOpx\setup\support> and run the following command:
resetCasuser.exe
2. Restart the daemon manager:
Net stop crmdmgtd
Net start crmdmgtd
Let me know how it works
If above did not help then send me the syslog.log and screen shot of the EventViewer with the latest Application Error that you see there.
--also screen shot of the below directory :
NMSROOT\etc\license
Thanks
Afroj

Is there a 32 Bit edition available for windows server 2012 and windows server 2008

Dear All,
Is there a 32 Bit edition available for windows server 2012 and windows server 2008?
Regards,
Ahmed

Hi,
Quote：
All editions of Windows Server 2008 R2 are 64-bit only.
Reference link below(session Supported upgrade paths):
https://technet.microsoft.com/en-us/library/dd379511(v=ws.10).aspx
And based on MS official description about system requirement for Windows Server 2012/2012 R2, we may find out that they only has 64 bit OS.
Best Regards,
Eve Wang
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Compatibility forms 6i and Windows Server 2008

Hi,
We want to change our Server from 2003 to Windows Server 2008 64bits.
My question is : is there a compatibility between Oracle forms 6i (our application) and Windows Server 2008 ?
Will the migration be successfull, or will we have some bugs?
Thks for your help.
O.

YES. It worked perfectly for me, you'll have to use oracle 8/8i lite though.

Urgent help needed to setup Forms 6i Server on Windows Server 2003

Hello,
I am trying to install Forms 6i Server from the Forms/Reports 6i Release 2 CD onto a server with Windows Server 2003 Standard Editon (services pack 1) installed.
The Oracle Installer produced the following error when I tried to install the Forms 6i Server From the Forms/Reports 6i Release 2 CD:
user1.pin(20); os_error while spawning ifsrv60 -install forms60server port=9000 mode=socket batch=yes.
Has anyone successfully installed Forms 6i Server from Forms/Reports 6i Release 2 CD onto a Windows Server 2003 server?
Any help is appreciated.
Phil

You it obtained to install the FORMS 6i SERVER in Windows 2003 ?
I am with the same problem and not yet I obtained solution.

T-500 and Windows Server 2008 R2 RTM

My setup:
T-500 dual booting via VHD - Windows 7 and Windows Server 2008 R2 (both 64-bit).
My problem:
I'm having a devil of a time with this one. I get random BSOD'd in my Server 2008 R2 installation, but my Win7 install is rock solid. Sometimes it's right away, sometimes after a few minutes, sometimes when trying to use WordPad. I cannot get my wireless card (Intel 5100 AGN) to work along with video drivers for my ATI card, so I'm leaning towards a driver issue. I'm trying to use the Win7 drivers for anything that's missing drivers at the moment, since they are the same under the hood, so to speak.
Has anyone else experimented with this setup and/or run into similar problems? Thanks!
T500: T9400 (2.53GHz), 4GB RAM, 160GB 7200rpm, 15.4in 1680x1050 WSXGA+ LCD, 256MB ATI Radeon HD3650, DVDRW, Intel 802.11agn wireless, AT&T WWAN, Bluetooth, Modem, 1Gb Ethernet, 9c Li-Ion, Windows 7 Ultimate x64 RC (Build 7100)

You shouldn't have any big issues, but there are a couple of gotchas that Server versions of Windows have (a notable one is the Bluetooth stack). Those are somewhat detailed in the review, though (and that blog also details how to get other features of Server 2008 R2 running).

AD RMS cluster with windows server 2008 R2 and Windows Server 2012 R2

please i'm trying to add ADRMS server with windows server 2012 R2 with our ADRMS 2008 R2 cluster. and it fails with the following error:
"The Client DLL version doesn't match with the one of the servers"
so i want to know is it supported to add RMS 2012 R2 server to RMS 2008 R2 Cluster
Thanks

They can't coexist, but usually what happens is you add the 2012 server, it migrates your cluster database and then your 2008r2 servers can no longer connect.
What is this value:
DRMS_Config database
dbo.DRMS_ClusterPolicies
AdrmsFileVersion

Need Help: TS130 Server and Windows Server 2008 R2 64 Bit Problems

Similar Messages

Maybe you are looking for