Need help: Unable to tether, personal hotspot settings are ON

Was hoping to see if I can get a solution here. Network service provider couldn't fix it.
1. tethering is enabled for the network I'm on.
2. My "Personal Hotspot" is on.
3. iPhone plugged in via USB
4. iTunes is running.
Unfortunately, it doesn't tether automatically like how it should. It's just not happening. I tried looking under the Network services and can't find the network to connect to.
Tethering used to work before I made the iOS 4.3 update, now it's not. Was wondering if any of you are having the same issue here? Or have a solution for this.

Turn off you Wifi everywhere and try the following:
I found a solution to USB tethering problems since recent firmware upgrades and share that here in case anyone else is having the same issue:
Since the introduction of the firmware update 4.3.2 or somewhere thereabouts, and personal hotspot implementation, "Tether using USB" has disappeared from the menu.
Semantically, where they've put it makes no sense (except financially, from forcing frustrated former users of USB tethering to use the wifi personal hotspot, forget, and rack up data charges with their carriers) - USB tethering is hiding under "Personal Hotspot" and the listed instructions don't work unless certain conditions are met. The iPhone shows up as a digital camera only under My Computer in Windows 7 until I follow the list below.
Here's how I got it to work today. There may be better ways and you may not need to take all steps but if you're like me you just want to get it working and carry on.
Solution: (assuming your iPhone is plugged in via USB, and Personal Hotspot is OFF (under Network | Personal Hotspot, and you're not connected to the Internet any other way....
0.     Close iTunes if it's open
1.    Turn Wifi off on your laptop
2.     Turn Wifi off on your iPhone
3.     Go into the Network | Personal Hotspot menu and turn P.H. on.
4.     I get a dialog querying whether I want to turn Wifi on, or to use USB or Bluetooth. Choose the second option
5.     Wait a little bit and it should find the device correctly and connect you to the internet. Verify with a web page.
Feel free to update or eliminate the list above and the assumptions but there you go, it works.
-Ian

Similar Messages

After the upgrade to ios7.1, I'm unable to use personal hotspot. When I click setup it prompts me to contact my carrier to enable

After the upgrade to ios7.1, I'm unable to use personal hotspot. When I click setup it prompts me to contact my carrier to enable.
My gadget is iPhone 4

Hey Owinoc,
Thanks for the question. I understand that you are experiencing issues with Personal Hotspot since upgrading to iOS 7.1. The following resource may provide a solution:
iOS: Troubleshooting Personal Hotspot
http://support.apple.com/kb/TS2756
Basic troubleshooting
1. See if your iOS device, computer, and wireless plan all meet the system requirements for Personal Hotspot.
2. Make sure Personal Hotspot is on: Tap Settings > Cellular > Personal Hotspot.
3. Check the Internet connection on your iOS device: Tap Safari and load a new webpage.
4. If one connection type doesn't work, try another. For example, instead of connecting using Wi-Fi, use USB or Bluetooth.
5. Turn Personal Hotspot off and on: Tap Settings > Personal Hotspot or Settings > Cellular > Personal Hotspot.
6. Install the latest version of iOS.
7. Reset your network settings: Tap Settings > General > Reset > Reset Network Settings.
8. If you still see the issue, restore the iPhone.
If you're still experiencing issues, try the steps below. […]
Thanks,
Matt M.

Trying to connect my iPad Air 1 to my iPhone 5S set as a hotspot via WiFi method. iPad sees the iPhone as wifi hotspot, but an error appears 'Remote Hotspot Failure .. Unable to start personal hotspot'. How do I fix this issue??

Trying to connect my iPad Air 1 to my iPhone 5S set as a hotspot via WiFi method. iPad sees the iPhone as wifi hotspot, but an error appears 'Remote Hotspot Failure .. Unable to start personal hotspot'. How do I fix this issue??

iOS: Troubleshooting Personal Hotspot - Apple Support

After updating my iPhone 4 to iOS 5 I couldn't find the personal hotspot icon in my setting and even in search option so I need help to get back my hotspot....

Personal hotspot cannot be found in ios 5 need help

Go to settings - general. - cellular my iPhone can't stop it from searching and I m sure it is using up my battery life

HT201270 I am unable to use personal hotspot in iPad 3

I am unable to get the settings as personal hotspot .

Does your carrier support it on the iPad (even if they support it on the iPhone they don't necessarily also support it on the iPad) ? You may also need to contact them in case it's an extra fee/subscription, and it should initially appear under Settings > General > Network > Personal Hotspot (http://support.apple.com/kb/HT4517)

I don't have personal hotspot settings and my internet provider (talk talk) doesn't provide them

I have an iPhone 5 and I tried to use my personal hotspot but I don't have settings for it. When I called Talk Talk - they were unable to provide me woth the settings (as they do not selol iPhones and I bought a sim only contract). Where can I get the settings for it? I have used personal hotspot on this phone but with different networks and they seem to run fine.

Is the personal hotspot feature part of your contract with your provider? If not, you will not be able to use it.

IPad mini retina, iOS 7 unable to join Personal Hotspot

I have iPhone 5, iPad mini retina running on iOS 7.1.2, Laptop Windows. When I turn on Personal Hotspot (PH), other PC, Tablet,.. suppose to join the PH normally via Wifi, Bluetooth, Cable. But I found that after my iPhone join a 5GHz band wifi, and then I turn on HP, other PC can't connect via Wifi, only can connect via Bluetooth or Cable.
I use a Linksys EA3500 dual band wifi router. It works perfectly for my need
So say in step that won't work:
1. Connect iPhone to a 5GHz band wifi at home
2. Later I hang out and need to share my 3G with my ipad mini wifi, so I turn on PH
3. All devices failed to connect to PH via Wifi, but bluetooth or cable can connect successful
Step that works:
1. iPhone already connect to 5GHz band at home, before I leaving home, I connect it again to a 2.4GHz band
2. Turn on PH where don't have wifi
3. Other device successful connect to PH.
So the problems here is the 5 GHz band problem with iPhone. After connect to 5GHz band, other devices can't connect to iPhone, like it refused other devices to connect to, or something like problem with iOS 7.
p/s: I have already doing the "clean" state of iOS 7 to test on both iPhone and iPad. Do a restore on both device, test its and same problem.

Thanks for your response,
You should check with the apple site before saying this, from iPhone 5 and above, it has already support for 5GHz bands. If my iPhone does not compatible with 5GHz bands how come it connect to 5GHz band back home

Unable to use personal hotspot from my iPhone4 after instaling IOS7

I'm a student and use personal hotspot a lot. Recently after upgrading to the new IOS7, I'm unable to connect to my laptop using personal hotspot. My phone version is iPhone 4. Thnx

Hey Owinoc
Checkout the article below for troubleshooting issues with Personal Hotspot.
iOS: Troubleshooting Personal Hotspot
http://support.apple.com/kb/TS2756
Thanks for using Apple Support Communities.
Regards,
-Norm G.

Need help: unable to login Adobe Content Viewer on iPad

Need help: not able to login with my Adobe Id and password on adobe content viewer on iPad. I'm able to login on the adobe.com site with my Id and password, but not on my iPad in the adobe content viewer. I've reset my Adobe ID password a couple of times to make sure I'm using the correct password and ID and I've even tried it with a complete new Adobe ID account, but it has not helped. Anybody who knows how to solve this?

Your Adobe ID needs to be verified to work with DPS. Can you use that Adobe ID to sign in to the Folio Builder panel? If not, sign in to http://digitalpublishing.acrobat.com and follow the prompts to verify the Adobe ID.
If your Adobe ID is verified, try removing the Adobe Content Viewer app from both the iPad and iTunes, sync, and install it again.

Need help: Unable Flatten pages because of Security setting

this is my code in myFunctions.js
var myFunctions = app.trustedFunction(function()
        app.beginPriv() ;
        this.flattenPages() ;
        app.endPriv() ;
and this code in vb
app.myFunctions()
but I am getting exception as Security settings are failng to flatten pages.
any idea?

If the PDF has any security applied, flattenPages() will fail. This includes:
Password, DRM or certificate-based permissions rules
Digital signatures that certify/lock the content
Reader-extended documents (use File > Save A Copy to remove the extension)

Need help, unable to find my Serial Number

I recently moved to a new house, with all the ensuing hassles. Shortly after moving I decided to upgrade my computer to Windows 8. And in order to try and get rid of some old problems I only kept the private files and did a clean update.
After (succesful) Windows upgrade I had to reinstall my Adobe Photoshop CS6 Extended, only to find out that I cannot find the box containing the CD. It must have been misplaced during our moving. On my Adobe account on adobe.com I find no trace of the order, although I did buy it through Adobe. All I have is an email from Adobe thanking me for buying the CS6 and encouraging me to register my new product. Which I forgot to do.
So here I am, without my serial number and thus unable to get Photoshop back onto my computer. This is extremely worrying, is there anything I can do?
Regards Rotski

Serial Number or Activation Issues
You need to contact Adobe Support either by chat or via phone when you have serial number and activation issues.
Here are some links to help make contact:
http://www.adobe.com/support/chat/ivrchat.html
http://www.adobe.com/support/download-install/supportinfo/

Need help unable to connect to the internet, ETHERNET not working, assigned IP address how to fix it on ethernet

I am unable to connect my imac to the internet. I tried to connect direct to the ETHERNET, and I am having ip address assigned problem on ethernet and also on my airport extreme, it said no internet connection or no DNS server. Please help . My internet provider is brighthouse and I just have a technician guy come to check it out and they can't fix it either. I have other laptop and I connect the ethernet directly and it work for my other laptop so I know it is not the internet provider problem, but my IMAC doesn't work. I hope I don't have to do a full recovery on my imac as I have a lot of info need to backup and I hope someone can help beside doing the full recovery.
Thanks
Carla

Backup everything. Note that a bootable backup/clone is optimum. Then, reinstall the unnamed OS.
iMac (27-inch Mid 2011), OS X Mavericks (10.9.3), SL & ML, G4 450 MP w/Leopard, 9.2.2

Need help to restore PeopleSoft Cofig Manager settings.

Hello all,
My Peoplesoft system:
HCM v9.0 (demoversion)
Tools v8.49
RDBMS: Oracle 10g
OS:Win XP pro
I have installed Peoplesoft recently.Everything was good.While working with Process Scheduler i have choosen wrong option,resulted deleted to Process Scheduler domain.At that time Process Scheduler was up.Immediately i lost Config Manager settings.
Unable login to Ptools like:Datamover,App designer and PeopleSoft login..
How can i restore those settings?
Please help....!!!
Edited by: user8970203 on Jan 19, 2010 4:07 PM

Can anybody helpme...Please!!!
Thanks
Edited by: user8970203 on Jan 20, 2010 5:42 AM

Need help: Unable to handle kernel paging request at virtual address; javac

Hi
we're working with apache tomcat under linux mandrake 10. (x86)
when our webapp get recompiled the server stop responding
(web server, telnet, etc... are down, but the server is pingable)
after a hard reboot , we get this message in var/log/messages :
Unable to handle kernel paging request at virtual address 02000064
kernel: printing eip:
kernel: c018e379
kernel: *pde = 00000000
kernel: Oops: 0000 [#1]
kernel: CPU: 1
kernel: EIP: 0060:[proc_pid_stat+137/928] Not tainted VLI
kernel: EIP: 0060:[<c018e379>] Not tainted VLI
kernel: EFLAGS: 00010286
kernel: EIP is at proc_pid_stat+0x89/0x3a0
kernel: eax: 00000000 ebx: 02000000 ecx: d85ac000 edx: 92960700
kernel: esi: d11ea6f0 edi: ded440a0 ebp: cf0ddf44 esp: cf0ddee4
kernel: ds: 007b es: 007b ss: 0068
kernel: Process javac (pid: 2415, threadinfo=cf0dc000 task=d11ea6f0)
kernel: Stack: c0143d5a c1259e78 00000000 c1259e78 c0343980 0000015b 00000000 cf0ddf40
attached ther is kernel messages, pci , dmesg.
Thanks
Massimo TRENTO
Apache Tomcat/4.1.30
j2sdk1.4.2_01
kernel 2.6.3-7mdksmp #1 SMP
--- DMESG ---
00100000 - 000000001f6f0000 (usable)
BIOS-e820: 000000001f6f0000 - 000000001f6fb000 (ACPI data)
BIOS-e820: 000000001f6fb000 - 000000001f700000 (ACPI NVS)
BIOS-e820: 000000001f700000 - 000000001f780000 (usable)
BIOS-e820: 000000001f780000 - 0000000020000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fed00400 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
503MB LOWMEM available.
found SMP MP-table at 000f7920
hm, page 000f7000 reserved twice.
hm, page 000f8000 reserved twice.
hm, page 0009f000 reserved twice.
hm, page 000a0000 reserved twice.
On node 0 totalpages: 128896
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 124800 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f7980
ACPI: RSDT (v001 PTLTD RSDT 0x00050000 LTP 0x00000000) @ 0x1f6f74ed
ACPI: FADT (v001 FSC D156x 0x00050000 0x000f4240) @ 0x1f6f751d
ACPI: MADT (v001 FSC APIC 0x00050000 CSF 0x00000000) @ 0x1f6faf76
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x00050000 LTP 0x00000001) @ 0x1f6fafd8
ACPI: DSDT (v001 FSC D156x 0x00050000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0xf008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:2 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
Using ACPI for processor (LAPIC) configuration information
Intel MultiProcessor Specification v1.1
Virtual Wire compatibility mode.
OEM ID: Product ID: APIC at: 0xFEE00000
I/O APIC #2 Version 32 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 2
Built 1 zonelists
Kernel command line: auto BOOT_IMAGE=linux-nonfb ro root=301 noapic devfs=mount acpi=ht resume=/dev/hda5
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 2793.223 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Memory: 504916k/515584k available (1920k kernel code, 9820k reserved, 892k data, 288k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 5537.79 BogoMIPS
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 225k freed
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU#0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU#0: Thermal monitoring enabled
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
per-CPU timeslice cutoff: 1462.56 usecs.
task migration cache decay timeout: 2 msecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Booting processor 1/1 eip 3000
Initializing CPU#1
masked ExtINT on CPU#1
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
Calibrating delay loop... 5570.56 BogoMIPS
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU#1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU#1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
Total of 2 processors activated (11108.35 BogoMIPS).
cpu_sibling_map[0] = 1
cpu_sibling_map[1] = 0
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 2792.0645 MHz.
..... host bus clock speed is 199.0474 MHz.
checking TSC synchronization across 2 CPUs: passed.
Starting migration thread for cpu 0
Starting migration thread for cpu 1
Brought up 1 CPUs
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfd8cb, last bus=3
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040211
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Disabled
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Transparent bridge - 0000:00:1e.0
PCI: Discovered primary peer bus 01 [IRQ]
PCI: Using IRQ router PIIX/ICH [8086/24d0] at 0000:00:1f.0
PCI: IRQ 0 for device 0000:00:1f.1 doesn't match PIRQ mask - try pci=usepirqmask
PCI: Found IRQ 10 for device 0000:00:1f.1
PCI: Sharing IRQ 10 with 0000:00:1d.2
PCI: Sharing IRQ 10 with 0000:00:1f.2
PCI: Sharing IRQ 10 with 0000:02:01.0
SBF: Simple Boot Flag extension found and enabled.
SBF: Setting boot flags 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
Starting balanced_irq
ikconfig 0.7 with /proc/config*
VFS: Disk quotas dquot_6.5.1
devfs: 2004-01-31 Richard Gooch ([email protected])
devfs: boot_options: 0x1
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
pty: 1024 Unix98 ptys configured
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 0000:00:1f.1
PCI: Found IRQ 10 for device 0000:00:1f.1
PCI: Sharing IRQ 10 with 0000:00:1d.2
PCI: Sharing IRQ 10 with 0000:00:1f.2
PCI: Sharing IRQ 10 with 0000:02:01.0
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x3000-0x3007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x3008-0x300f, BIOS settings: hdc:DMA, hdd:pio
hda: WDC WD800LB-07DNA2, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: LITE-ON COMBO LTC-48161H, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ICH5-SATA: IDE controller at PCI slot 0000:00:1f.2
PCI: Found IRQ 10 for device 0000:00:1f.2
PCI: Sharing IRQ 10 with 0000:00:1d.2
PCI: Sharing IRQ 10 with 0000:00:1f.1
PCI: Sharing IRQ 10 with 0000:02:01.0
ICH5-SATA: chipset revision 2
ICH5-SATA: 100% native mode on irq 10
ide2: BM-DMA at 0x3010-0x3017, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0x3018-0x301f, BIOS settings: hdg:pio, hdh:pio
hda: max request size: 1024KiB
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 >
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
EISA: Probing bus 0 at eisa0
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET: Registered protocol family 1
BIOS EDD facility v0.13 2004-Mar-09, 1 devices found
Please report your BIOS at http://linux.dell.com/edd/results.html
PM: Reading pmdisk image.
PM: Resume from disk failed.
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
SCSI subsystem initialized
libata version 1.00 loaded.
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: hda1: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 1038473
ext3_orphan_cleanup: deleting unreferenced inode 1038472
ext3_orphan_cleanup: deleting unreferenced inode 1038471
ext3_orphan_cleanup: deleting unreferenced inode 1038470
ext3_orphan_cleanup: deleting unreferenced inode 1038469
ext3_orphan_cleanup: deleting unreferenced inode 1038467
ext3_orphan_cleanup: deleting unreferenced inode 1038466
ext3_orphan_cleanup: deleting unreferenced inode 1038464
ext3_orphan_cleanup: deleting unreferenced inode 1038463
ext3_orphan_cleanup: deleting unreferenced inode 1038462
ext3_orphan_cleanup: deleting unreferenced inode 1038461
ext3_orphan_cleanup: deleting unreferenced inode 1038460
ext3_orphan_cleanup: deleting unreferenced inode 1038459
ext3_orphan_cleanup: deleting unreferenced inode 1038458
ext3_orphan_cleanup: deleting unreferenced inode 1038457
ext3_orphan_cleanup: deleting unreferenced inode 1038456
ext3_orphan_cleanup: deleting unreferenced inode 1038455
ext3_orphan_cleanup: deleting unreferenced inode 1038454
ext3_orphan_cleanup: deleting unreferenced inode 973782
EXT3-fs: hda1: 19 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Mounted devfs on /dev
Freeing unused kernel memory: 288k freed
Real Time Clock Driver v1.12
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1
PCI: Found IRQ 9 for device 0000:00:1d.0
PCI: Sharing IRQ 9 with 0000:00:02.0
PCI: Sharing IRQ 9 with 0000:00:1d.3
uhci_hcd 0000:00:1d.0: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 9, io base 00001400
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Found IRQ 11 for device 0000:00:1d.1
uhci_hcd 0000:00:1d.1: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 11, io base 00001800
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PCI: Found IRQ 10 for device 0000:00:1d.2
PCI: Sharing IRQ 10 with 0000:00:1f.1
PCI: Sharing IRQ 10 with 0000:00:1f.2
PCI: Sharing IRQ 10 with 0000:02:01.0
uhci_hcd 0000:00:1d.2: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 10, io base 00001c00
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
PCI: Found IRQ 9 for device 0000:00:1d.3
PCI: Sharing IRQ 9 with 0000:00:02.0
PCI: Sharing IRQ 9 with 0000:00:1d.0
uhci_hcd 0000:00:1d.3: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: irq 9, io base 00002000
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
PCI: Found IRQ 9 for device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 9, pci mem e0004000
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
EXT3 FS on hda1, internal journal
Adding 522072k swap on /dev/hda5. Priority:-1 extents:1
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 865 Chipset.
agpgart: Maximum main memory to use for agp memory: 431M
agpgart: Detected 8060K stolen memory.
agpgart: AGP aperture is 128M @ 0xf0000000
Supermount version 2.0.4 for kernel 2.6
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Intel(R) PRO/1000 Network Driver - version 5.2.30.1-k2
Copyright (c) 1999-2004 Intel Corporation.
PCI: Found IRQ 10 for device 0000:02:01.0
PCI: Sharing IRQ 10 with 0000:00:1d.2
PCI: Sharing IRQ 10 with 0000:00:1f.1
PCI: Sharing IRQ 10 with 0000:00:1f.2
PCI: Setting latency timer of device 0000:02:01.0 to 64
eth0: Intel(R) PRO/1000 Network Connection
inserting floppy driver for 2.6.3-7mdksmp
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
hdc: ATAPI 48X DVD-ROM CD-R/RW CD-MRW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
drivers/usb/core/usb.c: registered new driver hiddev
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
NET: Registered protocol family 17
e1000: eth0 NIC Link is Up 100 Mbps Half Duplex
PCI: Found IRQ 5 for device 0000:00:1f.5
PCI: Sharing IRQ 5 with 0000:00:1f.3
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 49851 usecs
intel8x0: clocking to 48000
NET: Registered protocol family 10
Disabled Privacy Extensions on device c037da00(lo)
IPv6 over IPv4 tunneling driver
Installing knfsd (copyright (C) 1996 [email protected]).
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
eth0: no IPv6 routers present
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
printk: 24045 messages suppressed.
Neighbour table overflow.
printk: 24276 messages suppressed.
Neighbour table overflow.
printk: 16555 messages suppressed.
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
printk: 24221 messages suppressed.
Neighbour table overflow.
printk: 24272 messages suppressed.
Neighbour table overflow.
printk: 15931 messages suppressed.
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
Neighbour table overflow.
printk: 24289 messages suppressed.
Neighbour table overflow.
printk: 21235 messages suppressed.
Neighbour table overflow.
---- LSPCI ---
00:00.0 Host bridge: Intel Corp. 82865G/PE/P Processor to I/O Controller (rev 02)
00:02.0 VGA compatible controller: Intel Corp. 82865G Integrated Graphics Device (rev 02)
00:03.0 PCI bridge: Intel Corp. 82865G/PE/P Processor to PCI to CSA Bridge (rev 02)
00:1d.0 USB Controller: Intel Corp. 82801EB USB (rev 02)
00:1d.1 USB Controller: Intel Corp. 82801EB USB (rev 02)
00:1d.2 USB Controller: Intel Corp. 82801EB USB (rev 02)
00:1d.3 USB Controller: Intel Corp. 82801EB USB (rev 02)
00:1d.7 USB Controller: Intel Corp. 82801EB USB2 (rev 02)
00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB/EB PCI Bridge (rev c2)
00:1f.0 ISA bridge: Intel Corp. 82801EB LPC Interface Controller (rev 02)
00:1f.1 IDE interface: Intel Corp. 82801EB Ultra ATA Storage Controller (rev 02)
00:1f.2 IDE interface: Intel Corp. 82801EB Ultra ATA Storage Controller (rev 02)
00:1f.3 SMBus: Intel Corp. 82801EB SMBus Controller (rev 02)
00:1f.5 Multimedia audio controller: Intel Corp. 82801EB AC'97 Audio Controller (rev 02)
02:01.0 Ethernet controller: Intel Corp.: Unknown device 1019
-- LSMOD --
Module Size Used by
nfsd 175840 8
exportfs 7552 1 nfsd
md5 4864 1
ipv6 251392 29
snd-seq-oss 33568 0
snd-seq-midi-event 8704 1 snd-seq-oss
snd-seq 55696 4 snd-seq-oss,snd-seq-midi-event
snd-pcm-oss 53316 0
snd-mixer-oss 19008 1 snd-pcm-oss
snd-intel8x0 34440 0
snd-ac97-codec 59588 1 snd-intel8x0
snd-pcm 97440 2 snd-pcm-oss,snd-intel8x0
snd-timer 26660 2 snd-seq,snd-pcm
gameport 5664 1 snd-intel8x0
snd-page-alloc 12996 2 snd-intel8x0,snd-pcm
snd-mpu401-uart 8320 1 snd-intel8x0
snd-rawmidi 25248 1 snd-mpu401-uart
snd-seq-device 9032 3 snd-seq-oss,snd-seq,snd-rawmidi
snd 55492 12 snd-seq-oss,snd-seq-midi-event,snd-seq,snd-pcm-oss,snd-mixer-oss,snd-intel8x0,snd-ac97-codec,snd-pcm,snd-timer,snd-mpu401-uart,snd-rawmidi,snd-seq-device
soundcore 10560 1 snd
af_packet 22632 0
hid 55360 0
raw 8640 1
ide-floppy 19776 0
ide-tape 36752 0
ide-cd 41764 0
cdrom 38272 1 ide-cd
floppy 61620 0
e1000 83460 0
supermount 39856 1
intel-agp 18364 1
agpgart 32460 2 intel-agp
ehci-hcd 25572 0
uhci-hcd 31856 0
usbcore 103228 5 hid,ehci-hcd,uhci-hcd
rtc 13640 0
ext3 114216 2
jbd 61976 1 ext3
sd_mod 17696 0
ata_piix 8836 0
libata 40256 1 ata_piix,[permanent]
scsi_mod 117104 2 sd_mod,libata
----- /var/log/kernel/warnings -------
Oct 5 10:16:47 nsilaslin02 kernel: printing eip:
Oct 5 10:16:47 nsilaslin02 kernel: c018e379
Oct 5 10:16:47 nsilaslin02 kernel: Oops: 0000 [#1]
Oct 5 10:16:47 nsilaslin02 kernel: CPU: 1
Oct 5 10:16:47 nsilaslin02 kernel: EIP: 0060:[proc_pid_stat+137/928] Not tainted VLI
Oct 5 10:16:47 nsilaslin02 kernel: EIP: 0060:[<c018e379>] Not tainted VLI
Oct 5 10:16:47 nsilaslin02 kernel: EFLAGS: 00010286
Oct 5 10:16:47 nsilaslin02 kernel: EIP is at proc_pid_stat+0x89/0x3a0
Oct 5 10:16:47 nsilaslin02 kernel: eax: 00000000 ebx: 02000000 ecx: d85ac000 edx: 92960700
Oct 5 10:16:47 nsilaslin02 kernel: esi: d11ea6f0 edi: ded440a0 ebp: cf0ddf44 esp: cf0ddee4
Oct 5 10:16:47 nsilaslin02 kernel: ds: 007b es: 007b ss: 0068
Oct 5 10:16:47 nsilaslin02 kernel: Process javac (pid: 2415, threadinfo=cf0dc000 task=d11ea6f0)
Oct 5 10:16:47 nsilaslin02 kernel: Stack: c0143d5a c1259e78 00000000 c1259e78 c0343980 0000015b 00000000 cf0ddf40
Oct 5 10:16:47 nsilaslin02 kernel: 52143e93 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Oct 5 10:16:47 nsilaslin02 kernel: 00000000 00000000 000000d0 00001000 000000d0 d11ea6f0 00000400 de64f060
Oct 5 10:16:47 nsilaslin02 kernel: Call Trace:
Oct 5 10:16:47 nsilaslin02 kernel: [buffered_rmqueue+234/400] buffered_rmqueue+0xea/0x190
Oct 5 10:16:47 nsilaslin02 kernel: [<c0143d5a>] buffered_rmqueue+0xea/0x190
Oct 5 10:16:47 nsilaslin02 kernel: [proc_info_read+75/320] proc_info_read+0x4b/0x140
Oct 5 10:16:47 nsilaslin02 kernel: [<c018b60b>] proc_info_read+0x4b/0x140
Oct 5 10:16:47 nsilaslin02 kernel: [vfs_read+142/224] vfs_read+0x8e/0xe0
Oct 5 10:16:47 nsilaslin02 kernel: [<c015bf2e>] vfs_read+0x8e/0xe0
Oct 5 10:16:47 nsilaslin02 kernel: [sys_read+46/80] sys_read+0x2e/0x50
Oct 5 10:16:47 nsilaslin02 kernel: [<c015c14e>] sys_read+0x2e/0x50
Oct 5 10:16:47 nsilaslin02 kernel: [sysenter_past_esp+82/121] sysenter_past_esp+0x52/0x79
Oct 5 10:16:47 nsilaslin02 kernel: [<c010b1b9>] sysenter_past_esp+0x52/0x79
Oct 5 10:16:47 nsilaslin02 kernel:
Oct 5 10:16:47 nsilaslin02 kernel: Code: 00 00 8b 7e 68 85 ff 74 09 57 e8 b3 5f f9 ff 59 89 c7 8b 8e 24 03 00 00 85 c9 74 38 8b 81 98 00 00 00 89 45 c8 8b 59 04 8b 51 08 <0f> bf 43 64 0f bf 5b 66 c1 e0 14 09 d8 01 d0 89 c1 c1 e9 14 0f
Oct 5 10:30:32 nsilaslin02 kernel: Linux version 2.6.3-7mdksmp ([email protected]) (gcc version 3.3.2 (Mandrake Linux 10.0 3.3.2-6mdk)) #1 SMP Wed Mar 17 14:24:28 CET 2004
Oct 5 10:30:32 nsilaslin02 kernel: BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
Oct 5 10:30:32 nsilaslin02 kernel: BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
Oct 5 10:30:32 nsilaslin02 kernel: BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
Oct 5 10:30:32 nsilaslin02 kernel: BIOS-e820: 0000000000100000 - 000000001f6f0000 (usable)
Oct 5 10:30:32 nsilaslin02 kernel: BIOS-e820: 000000001f6f0000 - 000000001f6fb000 (ACPI data)
Oct 5 10:30:32 nsilaslin02 kernel: BIOS-e820: 000000001f6fb000 - 000000001f700000 (ACPI NVS)
Oct 5 10:30:32 nsilaslin02 kernel: BIOS-e820: 000000001f700000 - 000000001f780000 (usable)
Oct 5 10:30:32 nsilaslin02 kernel: BIOS-e820: 000000001f780000 - 0000000020000000 (reserved)
Oct 5 10:30:32 nsilaslin02 kernel: BIOS-e820: 00000000fec00000 - 00000000fed00400 (reserved)
Oct 5 10:30:32 nsilaslin02 kernel: BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
Oct 5 10:30:32 nsilaslin02 kernel: BIOS-e820: 00000000ffb80000 - 00000000ffc00000 (reserved)
Oct 5 10:30:32 nsilaslin02 kernel: BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
Oct 5 10:30:32 nsilaslin02 kernel: hm, page 000f7000 reserved twice.
Oct 5 10:30:32 nsilaslin02 kernel: hm, page 000f8000 reserved twice.
Oct 5 10:30:32 nsilaslin02 kernel: hm, page 0009f000 reserved twice.
Oct 5 10:30:32 nsilaslin02 kernel: hm, page 000a0000 reserved twice.
Oct 5 10:30:32 nsilaslin02 kernel: On node 0 totalpages: 128896
Oct 5 10:30:32 nsilaslin02 kernel: DMA zone: 4096 pages, LIFO batch:1
Oct 5 10:30:32 nsilaslin02 kernel: Normal zone: 124800 pages, LIFO batch:16
Oct 5 10:30:32 nsilaslin02 kernel: HighMem zone: 0 pages, LIFO batch:1
Oct 5 10:30:33 nsilaslin02 kernel: Processor #0 15:2 APIC version 20
Oct 5 10:30:33 nsilaslin02 kernel: Processor #1 15:2 APIC version 20
Oct 5 10:30:33 nsilaslin02 kernel: Enabling APIC mode: Flat. Using 1 I/O APICs
Oct 5 10:30:33 nsilaslin02 kernel: Built 1 zonelists
Oct 5 10:30:33 nsilaslin02 kernel: Kernel command line: auto BOOT_IMAGE=linux-nonfb ro root=301 noapic devfs=mount acpi=ht resume=/dev/hda5
Oct 5 10:30:33 nsilaslin02 kernel: PID hash table entries: 2048 (order 11: 16384 bytes)
Oct 5 10:30:33 nsilaslin02 kernel: Detected 2793.223 MHz processor.
Oct 5 10:30:33 nsilaslin02 kernel: Console: colour VGA+ 80x25
Oct 5 10:30:33 nsilaslin02 kernel: Checking if this processor honours the WP bit even in supervisor mode... Ok.
Oct 5 10:30:33 nsilaslin02 kernel: Calibrating delay loop... 5537.79 BogoMIPS
Oct 5 10:30:33 nsilaslin02 kernel: Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Oct 5 10:30:33 nsilaslin02 kernel: Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Oct 5 10:30:33 nsilaslin02 kernel: POSIX conformance testing by UNIFIX
Oct 5 10:30:33 nsilaslin02 kernel: CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
Oct 5 10:30:33 nsilaslin02 kernel: per-CPU timeslice cutoff: 1462.56 usecs.
Oct 5 10:30:33 nsilaslin02 kernel: task migration cache decay timeout: 2 msecs.
Oct 5 10:30:33 nsilaslin02 kernel: enabled ExtINT on CPU#0
Oct 5 10:30:33 nsilaslin02 kernel: ESR value before enabling vector: 00000000
Oct 5 10:30:33 nsilaslin02 kernel: ESR value after enabling vector: 00000000
Oct 5 10:30:33 nsilaslin02 kernel: Booting processor 1/1 eip 3000
Oct 5 10:30:33 nsilaslin02 kernel: masked ExtINT on CPU#1
Oct 5 10:30:33 nsilaslin02 kernel: ESR value before enabling vector: 00000000
Oct 5 10:30:33 nsilaslin02 kernel: ESR value after enabling vector: 00000000
Oct 5 10:30:33 nsilaslin02 kernel: Calibrating delay loop... 5570.56 BogoMIPS
Oct 5 10:30:33 nsilaslin02 kernel: CPU1: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09
Oct 5 10:30:33 nsilaslin02 kernel: cpu_sibling_map[0] = 1
Oct 5 10:30:33 nsilaslin02 kernel: cpu_sibling_map[1] = 0
Oct 5 10:30:33 nsilaslin02 kernel: Using local APIC timer interrupts.
Oct 5 10:30:33 nsilaslin02 kernel: calibrating APIC timer ...
Oct 5 10:30:33 nsilaslin02 kernel: ..... CPU clock speed is 2792.0645 MHz.
Oct 5 10:30:33 nsilaslin02 kernel: ..... host bus clock speed is 199.0474 MHz.
Oct 5 10:30:33 nsilaslin02 kernel: checking TSC synchronization across 2 CPUs: passed.
Oct 5 10:30:33 nsilaslin02 kernel: Starting migration thread for cpu 0
Oct 5 10:30:33 nsilaslin02 kernel: Starting migration thread for cpu 1
Oct 5 10:30:33 nsilaslin02 kernel: Brought up 1 CPUs
Oct 5 10:30:33 nsilaslin02 kernel: PCI: Probing PCI hardware
Oct 5 10:30:33 nsilaslin02 kernel: PCI: Probing PCI hardware (bus 00)
Oct 5 10:30:33 nsilaslin02 kernel: Transparent bridge - 0000:00:1e.0
Oct 5 10:30:33 nsilaslin02 kernel: PCI: IRQ 0 for device 0000:00:1f.1 doesn't match PIRQ mask - try pci=usepirqmask
Oct 5 10:30:33 nsilaslin02 kernel: pty: 1024 Unix98 ptys configured
Oct 5 10:30:33 nsilaslin02 kernel: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Oct 5 10:30:33 nsilaslin02 kernel: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
Oct 5 10:30:33 nsilaslin02 kernel: RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
Oct 5 10:30:33 nsilaslin02 kernel: hda: WDC WD800LB-07DNA2, ATA DISK drive
Oct 5 10:30:33 nsilaslin02 kernel: Using anticipatory io scheduler
Oct 5 10:30:33 nsilaslin02 kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Oct 5 10:30:33 nsilaslin02 kernel: hdc: LITE-ON COMBO LTC-48161H, ATAPI CD/DVD-ROM drive
Oct 5 10:30:33 nsilaslin02 kernel: ide1 at 0x170-0x177,0x376 on irq 15
Oct 5 10:30:33 nsilaslin02 kernel: hda: max request size: 1024KiB
Oct 5 10:30:33 nsilaslin02 kernel: VFS: Mounted root (ext2 filesystem).
Oct 5 10:30:33 nsilaslin02 kernel: PCI: cache line size of 128 is not supported by device 0000:00:1d.7
Oct 5 10:30:33 nsilaslin02 kernel: hdc: ATAPI 48X DVD-ROM CD-R/RW CD-MRW drive, 2048kB Cache, UDMA(33)
Oct 5 10:30:33 nsilaslin02 kernel: ide-floppy driver 0.99.newide
Oct 5 10:30:39 nsilaslin02 kernel: atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
Oct 5 10:30:39 nsilaslin02 kernel: atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
Oct 5 10:30:39 nsilaslin02 kernel: atkbd.c: Unknown key released (translated set 2, code 0x7a on isa0060/serio0).
Oct 5 10:30:39 nsilaslin02 kernel: atkbd.c: This is an XFree86 bug. It shouldn't access hardware directly.
Oct 5 10:30:50 nsilaslin02 kernel: Neighbour table overflow.
Oct 5 10:30:50 nsilaslin02 last message repeated 9 times
Oct 5 10:30:55 nsilaslin02 kernel: printk: 24045 messages suppressed.
Oct 5 10:30:55 nsilaslin02 kernel: Neighbour table overflow.
Oct 5 10:31:00 nsilaslin02 kernel: printk: 24276 messages suppressed.
Oct 5 10:31:00 nsilaslin02 kernel: Neighbour table overflow.
Oct 5 10:36:06 nsilaslin02 kernel: printk: 16555 messages suppressed.
Oct 5 10:36:06 nsilaslin02 kernel: Neighbour table overflow.
Oct 5 10:36:06 nsilaslin02 last message repeated 9 times
Oct 5 10:36:11 nsilaslin02 kernel: printk: 24221 messages suppressed.
Oct 5 10:36:11 nsilaslin02 kernel: Neighbour table overflow.
Oct 5 10:36:16 nsilaslin02 kernel: printk: 24272 messages suppressed.
Oct 5 10:36:16 nsilaslin02 kernel: Neighbour table overflow.
Oct 5 10:46:22 nsilaslin02 kernel: printk: 15931 messages suppressed.
Oct 5 10:46:22 nsilaslin02 kernel: Neighbour table overflow.
Oct 5 10:46:22 nsilaslin02 last message repeated 9 times
Oct 5 10:46:27 nsilaslin02 kernel: printk: 24289 messages suppressed.
Oct 5 10:46:27 nsilaslin02 kernel: Neighbour table overflow.
Oct 5 10:46:32 nsilaslin02 kernel: printk: 21235 messages suppressed.
Oct 5 10:46:32 nsilaslin02 kernel: Neighbour table overflow.

Java programs are run by a virtual machine which is running in userland. They don't "mess" with the kernel.
OTOH, each userland program interacts with the kernel through system calls, signals, pageing activity, ...
My guess is that it's either broken hardware, or a fault in the linux kernel.
Is the crash reproducible? Does ist always crash with the same error message, at the same "eip" location?
If the crashes are sporadic and non deterministic, with different error messages each time, then I'd say it's
a hardware problem. Otherwise, it could be a linux kernel software problem.

Need Help-Unable to find an available port

Hi,
I am Working one BPEL Process where in need to invoke a WebService.
I was able to deploy my BPEL Process with the Web Service Call but i am getting an error while invoking the Webservice from the Process.
BPEL PM Version 10.1.2.0.2
<bindingFault>
<part name="summary" >
<summary>Unable to find an available port</summary>
</part>
</bindingFault>
Can you please let me know any work around is needed here.
Thanks in Advance
Edited by: user2574568 on Jun 24, 2009 8:28 AM
Edited by: user2574568 on Jun 24, 2009 12:23 PM

Include the following jar's in your classpath and re-compile ur code. It should work:
- commons-discovery.jar
- servlet-2_2.jar
- axis.jar
- saaj.jar
- jaxrpc.jar

Need help: Unable to tether, personal hotspot settings are ON

Similar Messages

Maybe you are looking for