Need help with 875P Neo-FIS2R!! No on board lan??

Hey i just got the 875P Neo-FIS2R, it came with bios 1.2 on it.
At that point I got everything working nice, INcluding the onboard lan card. I then went to live update bios to 1.6 through windows and I had no problems, but after I restarted my comp. it came back on with out detecting the onboard lan?? It was detected before,but ever since I updated to bios 1.6, it doesn't dectect the lan anymore!!! Anything I can do??

It could be something simple. Did you check to see if the onboard LAN is Enabled in the Bios?
I'd check that first!

Similar Messages

Need help for 875P Neo FIS2R

Hi,
i'm using 875P neo FIS2R mainboard. This is the message shown when passes the MSI screen during booting.
SATA 378 TX2 plus(tm) BIOS Version 1.00.1030.26
(c) 2002-2005 Promise Technology, Inc. All rights reserved.
No device is found!
BIOS is not installled.
So what is the device that has not been found? And why does the BIOS is not being installed?
And can someone help me on how to connect the LED cables? i can't make both the LED works.
Thanks!

It works. Thanks! :D
Currently i'm not using the RAID function. But what if in future i need to use the function? The message wil appear again. How do i fix it? Install the Promise Raid using the disk given?
The HDD LED is still not working. I've follow the instructions in the manual on connecting the LED to the mobo. Only one LED is functioning.
Intel P4 2.6CGhz 800Mhz HT enabled
MSI 875P Neo FIS-2R
AMIBIOS Version 1.60
Nvidia Geforce 2 MX400 64MB SD
WESTERN DIGITAL Caviar SE (8MB) WD800JB =80GB= ATA-100
KINGSTON 512MB (PC-3200)400MHz DDR
HEC 525W PSU
Thermaltake Xaser II Case
Windows XP Pro SP1

Need help w/ 875P Neo-FIS2R

875P Neo-FIS2R BIOS V 1.2
Intel CPU 2.8 FSB 800mhz
Corsair XMS Twin 512 (256 x 2)Dual Channel DDR 400 C2 LLPT
Sony DVD+R DRU500A (internal)
PowerColor Radeon 9700 Pro Evil Commando 2 AGP 128
Planar LCD 20" monitor DVI
Windows XP Pro
2 Western Digital ATA-100 100gig hardrives
Harddrives are only thing I kept from old system; unfortunately, I forgot to delete video drivers before installing in new system. Computer boots starts loading Win XP Pro then screen goes blank, Planar LCD monitor says no signal, so I figure the problem is the the AGP video card since I get this far. Windows won't load in safe mode either, screen just blanks monitor says no signal and it restarts with same results. I have changed BIOS settings to reflect 128 AGP aperture. LED monitor(in back)shows 1, 2 & 4 green and only 3 red. I am afraid to use flash utility to upgrade BIOS. I would prefer to upgrade via LiveUpdate. Help me get into windows via safe mode so I can uninstall old video drivers and install new video drivers.
Thx for your help.

Sorry,but if I got that right,u got a complete new system except the hdd´s.
But even with a "mobo only" change of ur system u should better make a complete windows new install.

Samsung pc3200 with 875P NEO FIS2R

Hi,
I have read numerous posts about problems with memory modules with the MSI 875P NEO FIS2R in this forum.
Just wondering if anyone has paired the MSI 875P NEO FIS2R with 2x512mb Samsung PC3200 with any of the latest BIOS version (1.4 at this time) WITHOUT overclocking? Any compatibility issues?
Thanks in advance.
amg

yes my timing is right with CPUz identifying it.
Its a COrsairPC3500C2PT. note am using a P4 2.4B not a C.
Am still waiting for my C chip

Need help with K9N NEO V3

I need a help and advice. I use before on my board one ram memory stick 2 gb and now buy another but they don`t wana work together. I have only 3.25 gb of memory in work and sometimes problem with starting computer.
Motherboar model name: MSI K9N Neo V3
model number: MS - 7369
Ami Bios: A7369NNS V2.4 112007
RAM: sitck i use before: KINGSTON, KHX6400D2/2G, HYPER - X
this one i buy now: TRANSCEND, 2G DDR 2 800 DIMM, 530811-3606 RoHs
CPU: Amd Athlon(tm) 64 X2 Dyal Core Processor 5000+
Memory Freqency for DDR3 667 (dual-channel)

Check this link: https://forum-en.msi.com/index.php?topic=108883.0

Need help with k8t neo ms-6702 and cpu compatiblility question.

I have a msi k8t neo motherboard socket 754 ms-6702 bios version 2.2 with a athlon 64 2800+ in my computer. I just bought a AMD Athlon 64 3700+ CPU Socket 754 .1MB cache. When i install it, my power goes on and i get no activity. Im wondering if i got a bad cpu off ebay or my bios isnt current enough ( i used msi live updating software and its currently at v 2.2) or does my motherboard not support this high of a cpu? Im not very computer literate. Thanks for any help and info. If i need to update my bios, i downloaded version 7.1 but i dont know how to flash it, can somone give me the steps

I had a bad experience with a 3700 bought on e bay ,turned out to be an engineering sample ."special m/b bios reqd" in my case I did get a boot and the engineering cmos message. genuine 3700 754's are quite rare and fetch premium prices.

Need Help with PT880 Neo

Yesterday, I bought all the parts to install a computer. I bought a PT8 Neo Series(MS-7008 v1.x) ATX mainboard, a Maxtar 160G harddrive, and a DVD CD RW. The problem is when I try to boot up the Windows XP CD, I get a boot failure error.
Boot Failure
Reboot and Select proper Boot device
or Insert Boot Media in selected Boot device
I have tried many things which makes me think that it's something with the bios.
I have connected it to a CD Rom that I know works and the error still comes up.
I have connected it to a harddrive that has an operating system with XP and it works fine.
I know about to boot sequence, and F6, and F11.
I have tried disabling the SATA, which didn't work.
I am running out of ideas on what the problem might be. Any help is greatly appreciated!

So are you saying is that you set the proper boot sequence in the bios but the thing still doesn't boot from the windows CD? If that's it, then it's probably something with the CD...
Cheers..

Major Problems with 875P Neo-FIS2R

Current Issue:
Upgraded to BIOS 1.6, waited for it to return to the C: prompt. Did a CTRL+ALT+DEL to restart, went through setup to make my 3Ware RAID controller the boot device. No other changes from default. Booted, it would get 1/2 way to booting Windows XP and then reboot itself (1st time I have seen that). So I powered it off (at the PS), waited 30s, powered it back on. Nothing, nada, ne rien. No the board won't even power on. I checked the PS, I am getting a +5V DC from the second power pin from the right on the bottom and +5V at the power switch jumper. The network LED is also lit.
Previous problems:
The board shipped with BIOS 1.2. It would intermittently freeze up, sometimes right after WinXP loaded, sometimes the next day. Then it just decided not to go beyond the BIOS splash page. At first I could power off, wait an hour, then it would boot, but after a couple of times it wouldn't boot at all and just hung with the MSI logo on.
I removed one stick of my Corsair Value Select 512MB PC3200 memory (VS512MB400) from slot 3 and left the other in slot 1. This allowed it to boot, I had done a CMOS reset earlier in attempts to fix the booting issue so I chose to use the default BIOS settings. I then upgraded to BIOS 1.6, see above for details on what happened.
Note: all settings were at default, no overclocking attempts, no alterations to memory power settings, etc.
Specs:
Antec SmartPower 400w (Brand new as old Antec TruePower fried)
MSI motherboard
2xVS512MB400 Corsair Value Select PC3200
3Ware 7500-4 ATA RAID Controller
4 100GB WD Caviar ATA 7200rpm drives in RAID 10
ATI Radeon VE AGP w/1DVI 1VGA
I am using the Firewire and USB brackets
Antec tower case w/2 rear fans, 1 front fan, 1 side fan
Igloo 4310 P4 fan
Toshiba SD-4102 DVD/CDRW
APC 700VA Backups pro
Any help is greatly appreciated

Quote
Originally posted by tAle*
Try clearing the cmos so that you can get back into the BIOS
Then increase the voltage of your RAM to 2.70V for PC3200 and the change memory clock fromm \"auto\" to 400
Tell me if this works 8)
tAle*
No sorry doesn't work.
As I wrote a view posts back, the bord doesn't start when the bios hasn't been reset.
This morning a completely stripped my PC, got the board out en connected only a floppy drive, but the board just won't start.
I have check if it could be the PSU but it works fine.
So a little summery:
* Board only starts after a CMOS CLEAR
* Power button works (tested it)
* PSU works (tested it)
* BIOS settings are right (Vdram @ 2.7, etc)
Any ideas?

Need help with msi 875p neo

i just bought one of these and set up my system, but as soon as i flick the power switch on the psu there is a 2 sec delay then it automaticaly boots up without me pushing anything then it just hangs..nothing no boot screen nothing. i check that d brakect thing and it says "Inializing keyboard controller" it stays there and does not change.
my system spec:
msi 875P Neo-FIS2R
intel Pentium 4 3.0GHz 800MHz Fsb
2 x 256 mb pc-3200 OCZ EL-DDR cas 2 @ DDR400
thermal take spark 7
leadtek winfast A280leTD 'Geforce 4 Ti 4200'
WD raptor 36.7 GB SATA 1
Xaser III casing
Thermaltake Purepower 480W
MS intellieye Explorer
plz help me i find no reason for it no to work

Quote
Originally posted by MaKoMaN
thaks for all ur help i found the problem one of my memory sticks had a scratch the other one works fine.. but now what do i do with the scratched one?
did you make the scratch? if not, you got warranty on it that would get you a new one...

HELP ! 875P Neo JAUD1 for front Audio with Thermaltake XASER III

I am trying to connect my new Thermalake case V2000A (the aluminium tower with 7 FANs) front (well top) audio connetors to JAUD1 on the motherboard (875P Neo FiS2R)
The XASER III wires say :
EAR L jumped with EAR L (Case manual says connect two "EAR L" to "BLINE_OUT_L" and "Line out_L" on motherboard)
EAR R jumped with EAR R (Case manual says connect two "EAR R" to "BLINE_OUT_R" and "Line out_R" on motherboard)
GND (Case manual says connect to "GROUND" or "AGND" on motherboard)
MIC IN (Case manual says connect to "MIC INPUT" or "MIC 2" on motherboard)
MIC VCC (Case manual says connect to "MIC POWER" or "MICPWR" on motherboard)
The JAUD1 connector on the motherboard comes with TWO green jumpers out of factory. One jumper shorting pins 9 & 10 and the other jumper shorting pins 5 & 6.
Page 2-25 of the motherboard manual says:
Pin 1 - AUD_MIC Front Panel Microphone input signal
Pin 2 - AUD_GND Ground used by analog Audio Circuits
Pin 3 - AUD_MIC_BIAS Microphone Power
Pin 4 - AUD_VCC Filtered +5V used by analog audio circuits
Pin 5 - AUD_FPOUT_R Right Channel audio signal to front panel
Pin 6 - AUD_RET_R Right channel audio signal return from front panel
pin 7 - HP_ON Reserved for future use to control headphone amplifier
pin 8 - KEY No pin
pin 9 - AUD_FPOUT_L Left channel audio signal to front panel
pin 10 - AUD_RET_L Left channel audio signal return from front panel
Now, I assume :
Case "MIC VCC" should go on Pin 3 (or maybe Pin 4 ?)
Case "MIC IN" should go on Pin 1
Case "GND" should go on Pin 2
Case "EAR R" should go on Pins 5 & 6 (I need to REMOVE the green jumper ?)
Case "EAR L" should go on Pins 9 & 10 (I need to REMOVE the green jumper ?)
Thanks for all help !

I have yet to put the PCI cards inside but so far I was able to reach that end corner of the motherboard with the case top sound cables.
As soon as I get answers on this Forum to my queries from more knowledged people about the right cabling (this and other posts on firewire and something else), I will then be able to finish all connections and finally place also the PCI cards and the video card and will let you know if it all went ok without the sound case cable stretching too much.
Thanks.
Quote
Originally posted by rwfish
Did you have any trouble getting the cables to stretch to the motherboard pins? I gave up on my (similar) setup.

[875P Neo Series] 875P NEO FIS2R - Bootup delay with disk attached to Promise RAID

Hi,
I have a problem with my 875P NEO FIS2R mobo. I just added a 400GB SATA RAID-0 array to the Promise controller and now I get a 50 second bootup delay after the BIOS has run through everything and beeped and before the first WinXP splash screen.
I boot up from a 160GB SATA RAID-0 array on the intel ICH5R controller. Both arrays work fine from within Windows. I have two DVD drives on the ICH5R PATA connection but nothing else on the Promise.
If I disable the Promise controller in BIOS the delay goes away.
I have tried disabling SMART, turning off the quick-boot option with no effect.
When I first installed my system I tested performance with booting from a single SATA drive on ICH5R vs Promise and I noticed the same issue, but didn't care then because I only needed one disk so I just kept Promise disabled in BIOS.
Any ideas how I can get around this?
Regards,
Jonathan

Sorry I have been a away for a few days.
Details requested...
Quote from: redeyedog on 21-June-05, 05:50:27
If the Promise controller was out of the picture (Disabled), and you have the SCSI adaptor and its devices setup:
1. What is the adaptor's SCSI ID?
7
Quote
2. List devices, position in the chain and their corresponding SCSI ID's.
#7 Adaptec 2930CU card
#4 Nikon Coolscan LS30 scanner
#3 Umax Astra 1220S scanner
#5 Iomega ZIP 100 drive
Quote
3. What type of terminination are you using?
Adaptec card has auto-termination.
ZIP drive has a termination connector attached.
Quote
4. Are the devices in the chain functioning properly?
Yes.
Quote
I agree that your problem is your SCSI controller. There may not be anything actually wrong with it. The 2930 was an agressive controller card and its BIOS simply may not coexist with your motherboard's BIOS optimally. Even with the BIOS disabled, it may be competing with the motherboard's request for handlers.
You may want to check to see if there is a BIOS update on Adaptec's website. Adaptec usually released 1 or 2 updates for each SCSI generation they produced. It may or may not help but we need to make sure you have the latest BIOS released.
Unfortunately, this card cannot be reflashed.
Quote
At any rate, I think you have found the component which is responsible for the delay. I'm willing to assist in diagnosing the issue but I need you to provide the specific information I'm requesting.
Also, try to do a CTRL-Pause to catch exactly what the BIOS version is and any other information which is showing up with the BIOS disabled. The SCSI adaptor BIOS, in fact, should not be enabled in your SCSI configuration as you have described thus far.
Adaptec AHA 2930CU SCSI BIOS v1.34.1.
There seems to be a difference between BIOS and host adapter BIOS. You always get the BIOS screen, but you can disable the host adapter BIOS if it is not required.
I am pretty sure it is not the SCSI chain that is wonr because the pause happens with nothing connected to the card.
Jonathan

875P Neo FIS2R-Slow boot with Raid on Intel + Raid on Promise

Hello all.
Here is the configuration I'm trying to set up (and almost did)
SI 875P Neo FIS2R,MS-6758 BIOS v2.4
P4 2.6 GHz HT
500W 6fan total
2x1G Kit DDR 400
2x74 G WD Raptor Raid0 (Intel S1-2) Win XP inst
2x36 G WD Raptor Raid0 (Promise S3-4)
GeCube X1600Pro
DVD-RW (IDE 2 )
Win XP SP2 (All latest updates installed)
I followed the instructions as they are listed in the sticky (great job btw) and configured the 2 SATA 74G WD Raptor on Intel Raid controller(serial1&2) as Raid0 and install WindowsXP Prof sp 2 on it.
Then I configured the 2 SATA 36G WD Raptor on Promise controller(serial3&4) as Raid0 and added this Raid to the existing WindowsXP installation.
This set up is working very good once I'm logged into Windows with no problems at all.
The glitch is that I need 3 min waiting time till I see the windows loading logo.
I have all the latest drivers installed also IAA and INFs and my bios is as the default values except the changes mentioned in the sticky
Onboard Promise IDE - as Raid
ON-Chip IDE Configuration:
Native Mode
SATA Only
Keep SATA Active - Yes
Keep PATA Active - Yes
PATA Channel selection - Both
Configure SATA as Raid - Yes
I did the Win XP installation twice till now, taking care to install INFs and drivers in the right order but the result is the same...3-5 mins till I have a fully operational windows environment and after that all is running like a dream.
Now, I've searched in the forum and saw that many more people have the same problem but never read the solution to it, so if someone has ever found the way to solve this or has the same configuration please tell me how he did it. Even if someone knows that it can't be solved just drop me a line telling me so. Altough the system is running smoothly I find the 3 min waiting time unacceptable and frustrating. I've run out of ideas so please help me.
Thanks in advance

Hello Blazer and thank you for replying.
Answering one at a time...
are both raid arrays setup with the same stripe size?--> Yes Both arrays are configured at 16k stripes
do you see both the intel and the promise bios setup screens?-->Yes both screens (Intel(R) RAID... and Fast Built (tm) ...)appear almost instantly after MSI's logo screen showing my Raid arrays in Normal status. The delay starts after the Promise's screen till the Windows Loading logo screen.
how is the raid bootable drive identified in the boot from menu?-->
Boot Device Priority:
1st BBS-0 (Raid): Intel <name> (---> this is the OS drive on Intel controller)
2nd Disabled
3rd Disabled
Try other boot devices NO
I have also the option to select the the Drive on Promise which shows as BBS-1 (Raid) FT 378 Ary 1 but I have left it out cause it doesn't have the OS on it.
is the OS drive labeled as C: and seen as 200GB drive [as one] from the four drive array]--> No as it shouldn't cause these are two different Raid Arrays. The first Raid on Intel's controller with the 2x74G WD Disks indeed shows as one C: 137 G and has the OS on it. The second on Promise controller with 2x36G WD Disks also shows as one D: 70G.These are two separate Arrays with 2 disks each and they show as indented.
is network boot enabled causing a delayed boot?--> I don't quit understand what you mean. In case you mean what happens if I unplug the 2 disks from the promise controller then yes if I do that the system boots fast in the Windows even if I leave the Bios setting "configure promise as raid"!!!
My problem is similar with this post: https://forum-en.msi.com/index.php?topic=69994.0
other posts that have reported the same trouble:
https://forum-en.msi.com/index.php?topic=94944.msg683258#msg683258
https://forum-en.msi.com/index.php?topic=81901.0
https://forum-en.msi.com/index.php?topic=66662.0
https://forum-en.msi.com/index.php?topic=98005.0 ---> I wish it was that simple, I did it as with all other drivers
I hope that info helps you helping me.

875P Neo FIS2R drive& bios settings help!!

Greetings guys.
Newbie here?
Would someone be so kind as to help me set up the following, using W2K as OS on the 875P Neo FIS2R board with P4 3.06 processor 2x512mb ram with a radeon 9700 and onboard sound, all the drivers etc are installed from the CD but am still using bios V1.2, not flashed it yet.......
I want my set up to be the following but I am having problems getting all my drives on the right chipsets.
IDE1= 1x120gb WD drive and 1x60gb drive for storage
IDE2= Sony DVDR
ICH5R to be 2x37gb WD SATA individual drive not raided on ser 1&2
Promise to be 2x37gb WD SATA as raid 0 for my OS
but I cannot work out the Bios settings and how to acheive what I want, assuming it is possible to do it this way.
Yes I know the quantity of drives is OTT but I did a good deal with a local shop in exchange for the 4x37gb SATA HDD's
Please make it simple, it takes ages to sink into my head...

make sure the "AS raid" option is enabled in BIOS under intergrated peripherals then on-chip conf.
that should handel the promise controller.
then you will need to read the manual to manually set each conf listed.
pg 3-24
these settings may do it:
ATA config set to P-ATA+S-ATA
S-ATA set to enable
P-ATA set to yes
P-ATA set to Both
Combined mode depends on where you install OS: suggest SATA
if that, then S-ATA 1st ch.
S-ATA RAID set to no
try this,let me know
Folk

Probems with msi 875p neo Fis2r and network controller driver

Hi guys just wondering if anyone could help me with my msi 875p neo FIS2R and problems with the network controller driver/network card.
I'm running xp on a computer my nextdoor neighbour gave me. I got it working fine with service pack 3 installed but then installed a bunch of windows updates last night and the computer would switch itself off before windows could start. Now I reinstalled xp and unfortunately it does not recognise the network controller/card at all now. I tried installing the intel network controller drivers but it stopped because it said no intel adapter/card was installed/present. Could anyone please help with suggestions? I tried running everest and under newtwork it doesnt list intel network adapters but I'm pretty certain it is. Again any suggestions?
--------[ EVEREST Home Edition (c) 2003-2005 Lavalys, Inc. ]
Computer:
Operating System Microsoft Windows XP Professional
OS Service Pack Service Pack 3
DirectX 4.09.00.0904 (DirectX 9.0c)
Motherboard:
CPU Type Intel Pentium 4, 2800 MHz (14 x 200)
Motherboard Name MSI 875P Neo-FIS2R (MS-6758) (5 PCI, 1 AGP, 4 DDR DIMM, Audio, Gigabit LAN, IEEE-1394)
Motherboard Chipset Intel Canterwood i875P
System Memory 1024 MB (PC3200 DDR SDRAM)
BIOS Type AMI (10/11/04)
Partitions:
C: (NTFS) 238464 MB (200326 MB free)
--------[ DMI ]---------------------------------------------------------------------------------------------------------
[ BIOS ]
BIOS Properties:
Vendor American Megatrends Inc.
Version V2.4
Release Date 10/11/2004
Size 512 KB
Boot Devices Floppy Disk, Hard Disk, CD-ROM, ATAPI ZIP, LS-120
Capabilities Flash BIOS, Shadow BIOS, Selectable Boot, EDD, BBS
Supported Standards DMI, APM, ACPI, ESCD, PnP
Expansion Capabilities ISA, PCI, AGP, USB
[ System ]
System Properties:
Manufacturer MICRO-STAR INC.
Product MS-6758
Version 00C
Serial Number 00000000
Wake-Up Type Modem Ring
[ Motherboard ]
Motherboard Properties:
Manufacturer MICRO-STAR INC.
Product MS-6758
Version 00C
Serial Number 00000000
[ Processors / Intel(R) Pentium(R) 4 Processor ]
Processor Properties:
Manufacturer Intel
Version Intel(R) Pentium(R) 4 Processor
External Clock 200 MHz
Maximum Clock 4000 MHz
Current Clock 2800 MHz
Type Central Processor
Voltage 3.3 V, 2.9 V
Status Enabled
Socket Designation FC-478
Network adapters:
Direct Parallel 5.1.2535.0
WAN Miniport (IP) 5.1.2535.0
WAN Miniport (IP) - Packet Scheduler Miniport 5.1.2535.0
WAN Miniport (L2TP) 5.1.2535.0
WAN Miniport (PPPOE) 5.1.2535.0
WAN Miniport (PPTP) 5.1.2535.0

Quote from: Jack t.N. on 14-November-09, 08:00:05
Clear CMOS with your PSU unplugged from A/C power. Then load "Optimized Defaults" in BIOS and retest.
thanks jimi... jack
will try that and post later if it worked... ive never cleared cmos, this sort of thing is relatively new to me but thanks again

Problem with my 875P NEO FIS2R when tyring to use x4 Crucial 512MB DDR modules

Hi all
I have a problem with my 875P NEO FIS2R when tyring to use x4 512MB DDR modules. At first the system seem fine then it just hangs on me. All modules are exactly same and I have tried updating my bios and adjusting the settings but nothing works. My system is fine when using x2 512MB moduels. I have searched the forum and found no clear answer although there are other people with this problem. Please can anyone let me know if there is anything I can do with my current configuration to make the x4 512MB DDR work?
From other posts I have learned so far that I either have to buy Paired modules from the manufacturer (which is no use because I bought my first x2 DDR a year ago) or only use x2 and now Dabs isnt taking the other x2 that I just bought because there is nothing wrong with the modules themselves (its the mobo).
I built my system from scratch and wouldnt have been able to have done it without previous assistance so thanks in advance for any help

Relaxing the timings will enable your RAMs to run at higher latencies so that they do not need to go extra mile to catch up with the transfer rates with the FSB.
Lowering the frequencies is like underclocking a speedy twin turbo to a standard single turbine which means lowering of speed so that the RAMs can run lower than expectations which'll be able to provide room for o/c'ing back near to its original frequency.

Need help with 875P Neo-FIS2R!! No on board lan??

Similar Messages

Maybe you are looking for