Need help with a WRT54GS V5.1
i need help with my WRT54GS V5.1 wireless router. it cannot connect to the internet and i don't know why. at the moment i have to use an ethernet cable coming from a virgin media modem. information that might be usefull. one of the antennas on the router is broke i am using windows vista on a toshiba laptop. the model is WRT54GS V5.1 thanks for people who help note: i am only 13 so somethings you say i might not understand.
Access Setup page of router .....
Click wireeless tab .... have a note of the wireless settings on that page .... Please click on the tab "Application and gaming" and click on sub
tab "Port range forwarding"
1) On the first line in Application box type in "Xbox", in start box
type in 88, in end box type in 88, in protocol keep it both, in ip
address type in 192.168.1.20 and give a check mark on enable box.
2) On the second line in Application box type in "Xbox", in start box
type in 3074, in end box type in 3074, in protocol keep it both, in ip
address type in 192.168.1.20 and give a check mark on enable box.
3) Now save the settings
4) Once you return to the setup page, click on the tab "Administration"
and disable the UPNP and save the settings.
5) Now assign the given ip address on your xbox
ip address :- 192.168.1.20
subnet mask :- 255.255.255.0
default gateway :- 192.168.1.1
Please assign the dns address on the xbox
primary dns :- 4.2.2.2
secondary dns :- 192.168.1.1
6) Please try to test your xbox live.
Similar Messages
-
So i seem to have gotten myself into a pickle. I am using the wrt54g v8 router which works fine but i needed to update the firmware, so i tried to access the router setup web page 192.168.1.1 however i could not do so from the computer connected to the lan line. ( the modem is a netgear hybrid router and i seem to only be able to pull up the netgear router on the lan settings) so i tried to update the firmware with a computer connected to the linksys router wirelessly and the firmware update started, however it ended mid update and now i can no longer get a signal from the linksys. can anyone help me undo this and get the firmware on my linksys router updated please.
What is the ip address you are getting on the computer...?
Which operating system you are using on the computer..?
Make sure that Power light should blink when you press the reset button on the router...Hard-reset the router for 45 seconds,power cycle the router and then,check the ip address you are getting on the computer connected to the router.
Click Start >> All Programs >> Accessories >> Command Prompt...A black box will appear(Command Prompt)...In the Command Prompt window type ipconfig and press 'Enter'...Look for Ethernet Adapter Local Area Connection IP Address , Subnet Mask and Default Gateway...
IP Address should be 192.168.1.x, Subnet Mask : 255.255.255.0, Default Gateway : 192.168.1.1 (assuming your router is 192.168.1.1)...If you get the above mentioned IP Address, Subnet and Gateway Address then you should ping the Gateway, type ping 192.168.1.1 and press Enter...If it gives you request timed out then disable any firewalls, security softwares on the computer...
If you get 4 replies then,Adjusting Browser Settings.... Open an IE, click Tools >> Internet Options, then delete all files, cookies, history, forms...Goto "Connections", make sure Never Dial a Connection is checked, click on LAN Settings and make sure all the options are unchecked...Once you are done click on O.k...Close the IE and re-open it...
Now try...You can also try with the different computer... -
I need help with my WRT54GS router.
My WRT54GS linksys router is acting up pretty bad. For example, i am just surfing the web and i have a program Ventrilo going talking to some friends, then all of a sudden i get disconnected from it and my internet just suddenly halts and then reconnects in a mere second or two. it also does this in the middle of me playing my online games. I have done every solution that i thought would remedy this problem, getting an ethernet cable, reinstalling Linksys, restarting my modem and router, changing my internet's security, reinstalling vista on my computer, EVERYTHING. I am not alone in this, my brother, plays the PS3 online, and my other brother plays a computer game on his computer. Anyway, while we are all doing our things on our own computers, we all get disconnected from the internet at the same time and it happens pretty frequently about once every 10-12 mins or so. Is anyone having the same problem, or does anyone have any ideas/solutions to this problem?
Message Edited by Vaun1992 on 02-23-2009 03:02 PMYou need to reset and re-configure your router to see if that makes any difference...Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
If you still face the same problem you should try to upgrade your router's firmware...
Download the Firmware from here ,
Follow these steps to upgrade the firmware on the device: -
Open an Internet Explorer browser page.In the address bar type - 192.168.1.1
Leave the username blank & in password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
If you still face the same problem you should connect one computer straight to the modem and check if you have stable internet connection or the same problem re-occurs... -
I have two wrt54g routers. The first one (RA) is connected to the modem and the computers. The second router (RB) is connected to my Direct TV HD-DVR (DVR). The DVR says it's connected to the network but not the internet. Please help.
Thank you,
Steve ZandmanTry asigning a static ip to the computer in the range of the router & it should work properly.
-
I have a Wireless-G Broadband Router Model- WRT54GS. I have been trying to get it to work for weeks. At one point it did work. It tells me that the EasyLink Advisor did not detect an active internet connection. But yet I am connected or I wouldn't be on here. On my laptop it shows the wireless connected but I can not get on the internet.
On the lap top check for the IP address you have then ping the gateway address if you are getting replies then ping the DNS 4.2.2.2 and post the results.
-
i'm trying to host games on my ps2. when i try to forward ports i go to the ip address in the browser search bar and when it ask me to put in username and password i put the default in admin. and it doesn't except it. i have held the reset button for a whole min. i even tried to reinstall the router and it ask for my password and my password doesn't work for that. can anyone please help?
Try resetting it harder, make sure when you press reset button, the power light of router blinks(which is solid otherwise), keep it pressed for 1 min, and let the power blink all the time.
After this turn off router and turn it on after 1 minute.
Now try to access setup page from a computer wired to router, and admin password should work. -
I have need help with something Please respond Quickly :)
I have need help with something Please respond Quickly ok so i have the linksys wrt54g Version 2.2 and i upgraded the firmware to V4.21.4 from this site http://homesupport.cisco.com/en-us/wireless/lbc/WRT54G and i clicked V2.2 for the router. So after i upgraded i lost internet ability i can't use the internet so i had to downgrade back to V4.21.1 but i want the things that newer update sloves. Please Help. Everything thing says DNS error? aka Modem.
$$Cgibbons$$Ya i tried that i tried restoring and redoing everything when i downgrade back to .1 it works fine though?
$$Cgibbons$$ -
Need help with a currently "in-use" form we want to switch to Adobes hosting service
Hi, I am in desperate need of help with some issues concerning several forms which we currently use a paid third party (not Adobe) to host and "re-distribute through email"...Somehow I got charged $14.95 for YOUR service, (signed up for a trial, but never used it)..and now I am paying for a year of use of the similar service which Adobe is in control of. I might want to port my form distribution through Adobe in the hopes of reducing the errors, problems and hassles my customers are experiencing when some of them push our "submit button". (and I guess I am familiar with these somewhat from reading what IS available in here, and I also know that, Adobe is working to alleviate some of these " submit" issues, so let's don't start by going backwards, here) I need solutions now for my issues or I can leave it as is, If Adobe's solution will be no better for my end users...
We used FormsCentral to code these forms and it works for the most part (if the end-user can co-operate, and thats iffy, sometimes), but I need help with how to make it go through your servers (and not the third party folks we use now), Not being cruel or racist here, but your over the phone "support techs" are about horrible & I cannot understand them or work with any of them, so I would definitely need someone who speaks English and can understand the nuances of programming these forms, to please contact me back. (Sorry, but both those attributes will be required to be able to help me, so, no "newbie-interns" or first week trainees are gonna cut it).... If you have anyone who fits the bill on those items and would be willing to help us, please contact me back at your earliest convenience. If we have to communicate here, I will do that & I can submit whatever we need to & to whoever we need to.
I need to get this right and working for the majority of my users and on any platform and OS.
You may certainly call me to talk about this, and I have given my number numerous times to your (expletive deleted) time wasting - recording message thingy. So, If it's not available look it up under [email protected]
(and you will probably get right to me, unlike my and I'm sure most other folks', "Adobe phone-in experiences")
Thank You,
Michael Corman
VinylCouture
Phenix City, Alabama 36869Well, thanks for writing back...just so you know...I started using Adobe products in 1987, ...yeah...back then...like Illustrator 1 & 9" B&W Macs ...John Warnock's Helvetica's....stuff like that...8.5 x 11 LaserWriters...all that good stuff...I still have some of it working on a mac...much of it was stuff I bought. some stuff I did not...I'm not a big fan of this "cloud" thing Adobe has foisted upon the creatives of the world...which I'm sure you can tell...but the functionality and usefulness of your software can not be disputed, so feel free to do whatever we will continue to pay for, ...I am very impressed with CC PS on the 64 bit PC and perhaps I will end up paying you the stipend that you demand for the other services.
So I guess that brings us to our problem.. a few years back and at the height of the recession and near bankruptcy myself, I was damn lucky and hit on something and began a small arts and crafts supply service to sell my products online to a very "niche market" ...I had a unique product and still sell that product (plus others) online...My website is www.vinylcouture.com...Strange? Yes...but there is a market it seems, for everything now, and this is the market I service...Catagorically, these are 99%+ women that use these "adhesive, sticky backed vinyl products" to make different "craft items" that are just way too various and numerous to go into... generally older women, women who are computer illiterate for the most part...and all this is irrelevant to my problem, but I want you to have every bit of background on this and especially the demographic we are dealing with, so we can get right to the meat of the problem.
OK...So about two years ago, I decided to offer a "plain sheet" product of a plain colored "stick back" vinyl... it is available in multiple quantities of packs ( like 5 pieces, 10 pieces, 15 pieces, in a packi & so on)...and if you are still on my site.. go to any "GO RIGHT TO OUR ORDER PAGE" button, scroll down a little...and then to the "PLAIN VINYL" section...you will see the Weebly website order process.) You can back out from here, I think,..but, anyway this product is available in 63 colors + or - a few. So then the problem is, how do they select their individual colors within that (whatever) pack?... .
So my initial idea was to enable a "selection form" for these "colors" that would be transmitted to me via email as 'part" of the "order process".. We tried getting our customers to submit a " a list" ( something my competitiors still do, lol, poor bastards)......but that..is just unbelievable..I can't even begin to tell you what a freakin' nightmare that was...these people cannot even count to 10, much less any higher... figuring out what colors to list and send me... well, lets just say, it wasn't working......I had to figure out a better way...Something had to be done.
So after thinking this all out, and yeah...due to my total ignorance, i figured that we could make a form with Live Cycle Designer (Now Forms Central)...(back then something that was bundled with Adobe Acrobat Pro), I believe, and thats what this thing was authored in... and it would be all good...LOL!
Well not so simple...as you well know, Adobe Acrobat would NOT LET YOU EMAIL anything from itself.....it just wouldn't work (and I know why, and all that hooey), but not being one to take NO for answer,.I started looking for a way to make my little gizmo work.. So I found this company that said they can "hijack" (re-direct actually) the request to email, bypass the wah-wah, and re-transmit it to the proper parties.....for less than $100 a year, I think...its called http://pdf-fillableforms.com/.
A nice gentleman named Joseph Silva helped us program the thing to go to his servers and back out. Please dont hassle them...I need them...for now..it basically does work...try it...you should get back a copy of the form that you filled out...good luck however, if you're on MAC OSX or similar...
I have included a copy of both of our forms (and feel free to fill it out and play with it)...just put test somewhere on it...(and you must include YOUR email or it will balk)..they are supposed to be mostly identical, except one seems to be twice as large....generating a 1.7 meg file upon submission, while the other one only generates a 600K file or so...thats another issue for another day or maybe you can advise on that also...
OK so far so good......In our shop, once Grandma buys a 10 pack (or whatever), Only then she gets to the link on her receipt page ro the relevant "selection form" ,(this prevents "Filling and Sending" with "no order" and "no payment", another early problem we had)... which they can click on and it will usually download and open up on their device if all goes well...Then our little form is supposed to be fillable and is supposed to ADD UP all the quantities, so grandma knows how many she is buying and so forth right on the fly, and even while she changes her mind..., and IT'S LARGE so grandma can see it, and then it TOTALS it all up for them, ( cause remember, they can NOT add).., except there is a programming bug (mouse-click should be a mouse-up probably or something..) which makes you click in the blank spaces to get to a correct TOTAL...about 70-80% of our customers can enable all these features and usually the process completes without problems for them especially on PC's running Windows OS and Acrobat Reader X or XI...at least for most... Unfortunately it is still not the "seamless process" I would like or had envisioned for the other folks out there that do have trouble using our form.... Many folks report to us the following issues that we know of. First of all it takes too much time to load up...We know its HUGE...is there anyway that you can see, to streamline this thing? I would love for it to be more compact...this really helps on the phones and pads as I'm sure you well know.
Some just tell us,"it WON'T work"....I believe this is because they are totally out of it and dont even have Adobe Reader on their machine, & don't know how to get it ( yes, we provide the links).....or it's some ancient version....no one can stop this one...
It almost always generates some kind ( at least one time) of "error message" which we do warn them about..., telling one, basically that "Acrobat doesnt even like this happening at all, and it could be detrimental to ones computer files", blah-blah...(this freaks grandma out really bad)...& usually they end up not even trying to send it... and then I get calls that even you wouldn't believe...& If they DO nut up and push the Red "Submit Form" button, it will usually send the thing to us (and also back to them at the "required email address" they furnished on the form, thats what the folks at the "fillable forms place" do) so, if it's performing it's functions, why it is having to complain?. What are we doing wrong?....and how can I fix it?...Will re-compiling it or saving it as a newer version of "FormsCentral" correct any of these problems ?
Ok, so that should keep you busy for a minute and we can start out with those problems...but the next thing is, how can I take advantage of YOUR re-direct & hosting services?, And will it get rid of the error messages, and the slowness, and the iOS incompatibilities ? (amazingly, the last iOS Reader version worked almost OK.. but the newest version doesnt seem to work with my form on my iphone4) If it will enable any version of the iOS to send my form correctly and more transparently, then it might be worth the money...$14.95 a MONTH you say. hmmmmm...Better be good.
Another problem is, that I really don't need 5000 forms a month submitted. I think its like 70-100 or less....Got any plans for that? Maybe I'm just not BIG ENOUGH to use Adobe's services, however in this case, I really don't care whose I do use as long as the product works most correctly for my customers as well as us. Like I said, If I'm doing the best I can, I won't change anything, and still use the other third party, If Adobe has a better solution, then i'm all for that as well. In the meantime, Thanks for any help you can provide on this...
Michael Corman
VinylCouture.com
(706) 326-7911 -
Need help with JTextArea and Scrolling
import java.awt.*;
import java.awt.event.*;
import java.text.DecimalFormat;
import javax.swing.*;
public class MORT_RETRY extends JFrame implements ActionListener
private JPanel keypad;
private JPanel buttons;
private JTextField lcdLoanAmt;
private JTextField lcdInterestRate;
private JTextField lcdTerm;
private JTextField lcdMonthlyPmt;
private JTextArea displayArea;
private JButton CalculateBtn;
private JButton ClrBtn;
private JButton CloseBtn;
private JButton Amortize;
private JScrollPane scroll;
private DecimalFormat calcPattern = new DecimalFormat("$###,###.00");
private String[] rateTerm = {"", "7years @ 5.35%", "15years @ 5.5%", "30years @ 5.75%"};
private JComboBox rateTermList;
double interest[] = {5.35, 5.5, 5.75};
int term[] = {7, 15, 30};
double balance, interestAmt, monthlyInterest, monthlyPayment, monPmtInt, monPmtPrin;
int termInMonths, month, termLoop, monthLoop;
public MORT_RETRY()
Container pane = getContentPane();
lcdLoanAmt = new JTextField();
lcdMonthlyPmt = new JTextField();
displayArea = new JTextArea();//DEFINE COMBOBOX AND SCROLL
rateTermList = new JComboBox(rateTerm);
scroll = new JScrollPane(displayArea);
scroll.setSize(600,170);
scroll.setLocation(150,270);//DEFINE BUTTONS
CalculateBtn = new JButton("Calculate");
ClrBtn = new JButton("Clear Fields");
CloseBtn = new JButton("Close");
Amortize = new JButton("Amortize");//DEFINE PANEL(S)
keypad = new JPanel();
buttons = new JPanel();//DEFINE KEYPAD PANEL LAYOUT
keypad.setLayout(new GridLayout( 4, 2, 5, 5));//SET CONTROLS ON KEYPAD PANEL
keypad.add(new JLabel("Loan Amount$ : "));
keypad.add(lcdLoanAmt);
keypad.add(new JLabel("Term of loan and Interest Rate: "));
keypad.add(rateTermList);
keypad.add(new JLabel("Monthly Payment : "));
keypad.add(lcdMonthlyPmt);
lcdMonthlyPmt.setEditable(false);
keypad.add(new JLabel("Amortize Table:"));
keypad.add(displayArea);
displayArea.setEditable(false);//DEFINE BUTTONS PANEL LAYOUT
buttons.setLayout(new GridLayout( 1, 3, 5, 5));//SET CONTROLS ON BUTTONS PANEL
buttons.add(CalculateBtn);
buttons.add(Amortize);
buttons.add(ClrBtn);
buttons.add(CloseBtn);//ADD ACTION LISTENER
CalculateBtn.addActionListener(this);
ClrBtn.addActionListener(this);
CloseBtn.addActionListener(this);
Amortize.addActionListener(this);
rateTermList.addActionListener(this);//ADD PANELS
pane.add(keypad, BorderLayout.NORTH);
pane.add(buttons, BorderLayout.SOUTH);
pane.add(scroll, BorderLayout.CENTER);
addWindowListener( new WindowAdapter()
public void windowClosing(WindowEvent e)
System.exit(0);
public void actionPerformed(ActionEvent e)
String arg = lcdLoanAmt.getText();
int combined = Integer.parseInt(arg);
if (e.getSource() == CalculateBtn)
try
JOptionPane.showMessageDialog(null, "Got try here", "Error", JOptionPane.ERROR_MESSAGE);
catch(NumberFormatException ev)
JOptionPane.showMessageDialog(null, "Got here", "Error", JOptionPane.ERROR_MESSAGE);
if ((e.getSource() == CalculateBtn) && (arg != null))
try{
if ((e.getSource() == CalculateBtn) && (rateTermList.getSelectedIndex() == 1))
monthlyInterest = interest[0] / (12 * 100);
termInMonths = term[0] * 12;
monthlyPayment = combined * (monthlyInterest / (1 - (Math.pow (1 + monthlyInterest, -termInMonths))));
lcdMonthlyPmt.setText(calcPattern.format(monthlyPayment));
if ((e.getSource() == CalculateBtn) && (rateTermList.getSelectedIndex() == 2))
monthlyInterest = interest[1] / (12 * 100);
termInMonths = term[1] * 12;
monthlyPayment = combined * (monthlyInterest / (1 - (Math.pow (1 + monthlyInterest, -termInMonths))));
lcdMonthlyPmt.setText(calcPattern.format(monthlyPayment));
if ((e.getSource() == CalculateBtn) && (rateTermList.getSelectedIndex() == 3))
monthlyInterest = interest[2] / (12 * 100);
termInMonths = term[2] * 12;
monthlyPayment = combined * (monthlyInterest / (1 - (Math.pow (1 + monthlyInterest, -termInMonths))));
lcdMonthlyPmt.setText(calcPattern.format(monthlyPayment));
catch(NumberFormatException ev)
JOptionPane.showMessageDialog(null, "Invalid Entry!\nPlease Try Again", "Error", JOptionPane.ERROR_MESSAGE);
} //IF STATEMENTS FOR AMORTIZATION
if ((e.getSource() == Amortize) && (rateTermList.getSelectedIndex() == 1))
loopy(7, 5.35);
if ((e.getSource() == Amortize) && (rateTermList.getSelectedIndex() == 2))
loopy(15, 5.5);
if ((e.getSource() == Amortize) && (rateTermList.getSelectedIndex() == 3))
loopy(30, 5.75);
if (e.getSource() == ClrBtn)
rateTermList.setSelectedIndex(0);
lcdLoanAmt.setText(null);
lcdMonthlyPmt.setText(null);
displayArea.setText(null);
if (e.getSource() == CloseBtn)
System.exit(0);
private void loopy(int lTerm,double lInterest)
double total, monthly, monthlyrate, monthint, monthprin, balance, lastint, paid;
int amount, months, termloop, monthloop;
String lcd2 = lcdLoanAmt.getText();
amount = Integer.parseInt(lcd2);
termloop = 1;
paid = 0.00;
monthlyrate = lInterest / (12 * 100);
months = lTerm * 12;
monthly = amount *(monthlyrate/(1-Math.pow(1+monthlyrate,-months)));
total = months * monthly;
balance = amount;
while (termloop <= lTerm)
displayArea.setCaretPosition(0);
displayArea.append("\n");
displayArea.append("Year " + termloop + " of " + lTerm + ": payments\n");
displayArea.append("\n");
displayArea.append("Month\tMonthly\tPrinciple\tInterest\tBalance\n");
monthloop = 1;
while (monthloop <= 12)
monthint = balance * monthlyrate;
monthprin = monthly - monthint;
balance -= monthprin;
paid += monthly;
displayArea.setCaretPosition(0);
displayArea.append(monthloop + "\t" + calcPattern.format(monthly) + "\t" + calcPattern.format(monthprin) + "\t");
displayArea.append(calcPattern.format(monthint) + "\t" + calcPattern.format(balance) + "\n");
monthloop ++;
termloop ++;
public static void main(String args[])
MORT_RETRY f = new MORT_RETRY();
f.setTitle("MORTGAGE PAYMENT CALCULATOR");
f.setBounds(600, 600, 500, 500);
f.setLocationRelativeTo(null);
f.setVisible(true);
}need help with displaying the textarea correctly and the scroll bar please.
Message was edited by:
new2this2020What's the problem you're having ???
PS. -
Need help with trim and null function
Hi all,
I need help with a query. I use the trim function to get the first three characters of a string. How do I write my query so if a null value occurs in combination with my trim to say 'Null' in my results?
ThanksHi,
Thanks for the reply. What am I doing wrong?
SELECT trim(SUBSTR(AL1.user_data_text,1,3)),NVL
(AL1.user_data_text,'XX')
FROM Table
I want the XX to appear in the same column as the
trim.The main thing you're doing wrong is not formatting your code. The solution may become obvious if you do.
What you're saying is:
SELECT trim ( SUBSTR (AL1.user_data_text, 1, 3))
, NVL ( AL1.user_data_text, 'XX' )
FROM Tablewhich makes it clear that you're SELECTing two columns, when you only want to have one.
If you want that column to be exactly like the first column you're currently SELECTing, except that when that column is NULL you want it to be 'XX', then you have to apply NVL to that column, like this:
SELECT NVL ( trim ( SUBSTR (AL1.user_data_text, 1, 3))
, 'XX'
FROM Table -
I need help with resetting my ichat. When i try to login now it wont let me... it says "AOL Instant Messenger password" and then "iChat can't log in to ... because your login ID or password is incorrect. How do I reset this if I cant log in? When I try to press online the same thing pops up and I have no way of logging in or asking for help.
Hi,
iChat (it would help to know which version) can accept Apple IDs as valid AIM Screen Names.
However if you have iChat 5 or earlier you cannot use ones ending in @me.com or @icloud.com issued by iCloud. (they can be used in iChat 6 or Messages as these versions make a double login to AIM and Apple to allow the use of the password).
In addition if you are using an Apple ID for an AIM Screen Name the password still needs to keep to the 16 character limit that AIM has.
AN @mac.com name can be used on any version of iChat (Until the 30th June 2014)
As it does not need a double check with Apple you can use it to log in to the AIM Web pages
Login here with an AIM Name registered at AIM or and @mac.com name and see if you get any suspended account messages.
Sometimes account can be suspended. Usually because something has triggered the "Unusual Activity" item.
About a year ago many @mac.com users that travelled out of their own country found themselves suspended when they got home.
If the Name checks out of if an Apple ID the password in known to be 16 characters or Less then do this:-
In Lion upwards open a Finder Window and use the Go Menu whilst holding down the ALT key.
Select the Library that appears in the menu list.
Navigate to Preferences.
(If you have version earlier than Lion the just navigate to ~/Library/Preferences (that's the Library in you Home - Little House icon - folder)
Fnd com.apple.ichat.aim.plist (even if you are using Messages)
Drag the file to the Trash and Restart the app.
7:39 pm Thursday; May 29, 2014
iMac 2.5Ghz i5 2011 (Mavericks 10.9)
G4/1GhzDual MDD (Leopard 10.5.8)
MacBookPro 2Gb (Snow Leopard 10.6.8)
Mac OS X (10.6.8),
Couple of iPhones and an iPad -
Need help with Airport Express and so on.
Ok so my main problem before getting into what I need help with here is that our MacBooks and now my iPhone 6 plus isn't staying online. Keep getting booted off and then I either have to select the network again or it will eventually go back on. If anyone has a solution or so please feel free to answer that as well. I'm running on Roadrunner with a Netgear 600 wireless router and a motorola modem. Both of which I'll leave the link to below for a better look.
My Main Question: So I'm looking at a new wireless router mainly and possibly a new modem. I know Apple products are trustworthy but how good is the Airport Express and other Airport products. Also what is the Maximum speed and Maximum data speed for the cheapest express station and if anyone knows the speeds of the other devices it would be greatly appreciated.DSL Router to Netgear 5-port Switch and I used the switch to connect to Airport Extreme, TV, Blue-Ray DVD player and DirecTV Receiver.
The AirPort Extreme base station (AEBS) is a router so it will do what you need.
You need to reconfigure your setup. Connect the WAN port of the AEBS to the DSL router. Then connect the Netgear switch to one of the LAN ports on the AEBS. The AEBS will properly share the connection. -
I need help with shooting in my flash game for University
Hi there
Ive tried to make my tank in my game shoot, all the code that is there works but when i push space to shoot which is my shooting key it does not shoot I really need help with this and I would appriciate anyone that could help
listed below should be the correct code
//checking if the space bar is pressed and shooting is allowed
if(evt.keyCode == 32 && shootAllow){
//making it so the user can't shoot for a bit
shootAllow = false;
//declaring a variable to be a new Bullet
var newBullet:Bullet = new Bullet();
//changing the bullet's coordinates
newBullet.y = tank_mc.y + tank_mc.width/2 - newBullet.width/2;
newBullet.x = tank_mc.x;
//then we add the bullet to stage
addChild(newBullet);
listed below is my entire code
import flash.display.MovieClip;
//declare varibles to create mines
//how much time before allowed to shoot again
var cTime:int = 0;
//the time it has to reach in order to be allowed to shoot (in frames)
var cLimit:int = 12;
//whether or not the user is allowed to shoot
var shootAllow:Boolean = true;
var minesInGame:uint;
var mineMaker:Timer;
var cursor:MovieClip;
var index:int=0;
var tankMine_mc:MovieClip;
var antiTankmine_mc:MovieClip;
var maxHP:int = 100;
var currentHP:int = maxHP;
var percentHP:Number = currentHP / maxHP;
function initialiseMine():void
minesInGame = 15;
//create a timer fires every second
mineMaker = new Timer(6000, minesInGame);
//tell timer to listen for Timer event
mineMaker.addEventListener(TimerEvent.TIMER, createMine);
//start the timer
mineMaker.start();
function createMine(event:TimerEvent):void
//var tankMine_mc:MovieClip;
//create a new instance of tankMine
tankMine_mc = new Mine();
//set the x and y axis
tankMine_mc.y = 513;
tankMine_mc.x = 1080;
// adds mines to stage
addChild(tankMine_mc);
tankMine_mc.addEventListener(Event.ENTER_FRAME, moveHorizontal);
function moveHorizontal(evt:Event):void{
evt.target.x -= Math.random()*5;
if (evt.target.x >= stage.stageWidth)
evt.target.removeEventListener(Event.ENTER_FRAME, moveHorizontal);
removeChild(DisplayObject(evt.target));
initialiseMine();
//declare varibles to create mines
var atmInGame:uint;
var atmMaker:Timer;
function initialiseAtm():void
atmInGame = 15;
//create a timer fires every second
atmMaker = new Timer(8000, minesInGame);
//tell timer to listen for Timer event
atmMaker.addEventListener(TimerEvent.TIMER, createAtm);
//start the timer
atmMaker.start();
function createAtm(event:TimerEvent):void
//var antiTankmine_mc
//create a new instance of tankMine
antiTankmine_mc = new Atm();
//set the x and y axis
antiTankmine_mc.y = 473;
antiTankmine_mc.x = 1080;
// adds mines to stage
addChild(antiTankmine_mc);
antiTankmine_mc.addEventListener(Event.ENTER_FRAME, moveHorizontal);
function moveHorizontal_2(evt:Event):void{
evt.target.x -= Math.random()*10;
if (evt.target.x >= stage.stageWidth)
evt.target.removeEventListener(Event.ENTER_FRAME, moveHorizontal);
removeChild(DisplayObject(evt.target));
initialiseAtm();
function moveForward():void{
bg_mc.x -=10;
function moveBackward():void{
bg_mc.x +=10;
var tank_mc:Tank;
// create a new Tank and put it into the variable
// tank_mc
tank_mc= new Tank;
// set the location ( x and y) of tank_mc
tank_mc.x=0;
tank_mc.y=375;
// show the tank_mc on the stage.
addChild(tank_mc);
stage.addEventListener(KeyboardEvent.KEY_DOWN, onMovementKeys);
//creates the movement
function onMovementKeys(evt:KeyboardEvent):void
//makes the tank move by 10 pixels right
if (evt.keyCode==Keyboard.D)
tank_mc.x+=5;
//makes the tank move by 10 pixels left
if (evt.keyCode==Keyboard.A)
tank_mc.x-=5
//checking if the space bar is pressed and shooting is allowed
if(evt.keyCode == 32 && shootAllow){
//making it so the user can't shoot for a bit
shootAllow = false;
//declaring a variable to be a new Bullet
var newBullet:Bullet = new Bullet();
//changing the bullet's coordinates
newBullet.y = tank_mc.y + tank_mc.width/2 - newBullet.width/2;
newBullet.x = tank_mc.x;
//then we add the bullet to stage
addChild(newBullet);
if (tank_mc.hitTestObject(antiTankmine_mc))
//tank_mc.gotoAndPlay("hit");
currentHP -= 10;
// remove anti tank mine
removeChild(antiTankmine_mc);
if (tank_mc.hitTestObject(tankMine_mc))
//tank_mc.gotoAndPlay("hit");
currentHP -= 10;
// remove anti tank mine
removeChild(tankMine_mc);
//var maxHP:int = 100;
//var currentHP:int = maxHP;
//var percentHP:Number = currentHP / maxHP;
//Incrementing the cTime
//checking if cTime has reached the limit yet
if(cTime < cLimit){
cTime ++;
} else {
//if it has, then allow the user to shoot
shootAllow = true;
//and reset cTime
cTime = 0;
function updateHealthBar():void
percentHP = currentHP / maxHP;
healthBar.barColor.scaleX = percentHP;
if(currentHP <= 0)
currentHP = 0;
trace("Game Over");
updateHealthBar();USe the trace function to analyze what happens and what fails to happen in the code you showed. trace the conditional values to see if they are set up to allow a shot when you press the key
-
Need help with conditional query
guys this is just an extension of this post that Frank was helping me with. im reposting because my requirements have changes slightly and im having a hell of a time trying to modify the query.
here is the previous post.
need help with query that can look data back please help.
CREATE TABLE "FGL"
"FGL_GRNT_CODE" VARCHAR2(60),
"FGL_FUND_CODE" VARCHAR2(60),
"FGL_ACCT_CODE" VARCHAR2(60),
"FGL_ORGN_CODE" VARCHAR2(60),
"FGL_PROG_CODE" VARCHAR2(60),
"FGL_GRNT_YEAR" VARCHAR2(60),
"FGL_PERIOD" VARCHAR2(60),
"FGL_BUDGET" VARCHAR2(60)
)data
Insert into FGL (FGL_GRNT_CODE,FGL_FUND_CODE,FGL_ACCT_CODE,FGL_ORGN_CODE,FGL_PROG_CODE,FGL_GRNT_YEAR,FGL_PERIOD,FGL_BUDGET) values ('240055','240055','7600','4730','02','11','00','400');
Insert into FGL (FGL_GRNT_CODE,FGL_FUND_CODE,FGL_ACCT_CODE,FGL_ORGN_CODE,FGL_PROG_CODE,FGL_GRNT_YEAR,FGL_PERIOD,FGL_BUDGET) values ('240055','240055','7240','4730','02','10','1','100');
Insert into FGL (FGL_GRNT_CODE,FGL_FUND_CODE,FGL_ACCT_CODE,FGL_ORGN_CODE,FGL_PROG_CODE,FGL_GRNT_YEAR,FGL_PERIOD,FGL_BUDGET) values ('240055','240055','7240','4730','02','10','1','0');
Insert into FGL (FGL_GRNT_CODE,FGL_FUND_CODE,FGL_ACCT_CODE,FGL_ORGN_CODE,FGL_PROG_CODE,FGL_GRNT_YEAR,FGL_PERIOD,FGL_BUDGET) values ('240055','240055','7600','4730','02','11','1','400');
Insert into FGL (FGL_GRNT_CODE,FGL_FUND_CODE,FGL_ACCT_CODE,FGL_ORGN_CODE,FGL_PROG_CODE,FGL_GRNT_YEAR,FGL_PERIOD,FGL_BUDGET) values ('360055','360055','7200','4730','02','10','1','400');
Insert into FGL (FGL_GRNT_CODE,FGL_FUND_CODE,FGL_ACCT_CODE,FGL_ORGN_CODE,FGL_PROG_CODE,FGL_GRNT_YEAR,FGL_PERIOD,FGL_BUDGET) values ('360055','360055','7600','4730','02','10','1','400');
Insert into FGL (FGL_GRNT_CODE,FGL_FUND_CODE,FGL_ACCT_CODE,FGL_ORGN_CODE,FGL_PROG_CODE,FGL_GRNT_YEAR,FGL_PERIOD,FGL_BUDGET) values ('240055','240055','7240','4730','02','10','14','200');
Insert into FGL (FGL_GRNT_CODE,FGL_FUND_CODE,FGL_ACCT_CODE,FGL_ORGN_CODE,FGL_PROG_CODE,FGL_GRNT_YEAR,FGL_PERIOD,FGL_BUDGET) values ('240055','240055','7600','4730','02','10','14','100');
Insert into FGL (FGL_GRNT_CODE,FGL_FUND_CODE,FGL_ACCT_CODE,FGL_ORGN_CODE,FGL_PROG_CODE,FGL_GRNT_YEAR,FGL_PERIOD,FGL_BUDGET) values ('240055','240055','7240','4730','02','10','14','200');
Insert into FGL (FGL_GRNT_CODE,FGL_FUND_CODE,FGL_ACCT_CODE,FGL_ORGN_CODE,FGL_PROG_CODE,FGL_GRNT_YEAR,FGL_PERIOD,FGL_BUDGET) values ('240055','240055','7240','4730','02','10','2','100');
Insert into FGL (FGL_GRNT_CODE,FGL_FUND_CODE,FGL_ACCT_CODE,FGL_ORGN_CODE,FGL_PROG_CODE,FGL_GRNT_YEAR,FGL_PERIOD,FGL_BUDGET) values ('240055','240055','7240','4730','02','11','2','600');
I need to find the greatest grant year for the grant by a period parameter.
once i find the greatest year i need to check the value of period 14 for that grant for the previous year and add it to the budget amount for that grant. however if their is an entry in the greatest year for period 00 then i need to ignore the period 14 of previous year and do this calculation current period +(current period - greatest year 00)
hope that makes sense so in other words with the new data above. if i was querying period two of grant year 11. i would end up with $800
because the greatest year is 11 it contains a period 0 with amount of $400 so my total should be
period 2 amount $ 600
period 0 amount $ 400 - period 2 amount of $600 = 200
600+200 = $800
if i query period 1 of grant 360055 i would just end up with 800 of grnt year 10.
i have tried to modify that query you supplied to me with no luck. I have tried for several day but im embarrased to say i just can get it to do what im trying to do .
can you please help me out.
here is the query supplied by frank kulash who gracefully put this together for me.
WITH got_greatest_year AS
SELECT fgl.* -- or whatever columns are needed
, MAX ( CASE
WHEN fgl_period = :given_period
THEN fgl_grnt_year
END
) OVER () AS greatest_year
FROM fgl
SELECT SUM (fgl_budget) AS total_budget -- or SELECT *
FROM got_greatest_year
WHERE ( fgl_grnt_year = greatest_year
AND fgl_period = :given_period
OR ( fgl_grnt_year = greatest_year - 1
AND fgl_period = 14
;MiguelHi, Miguel,
Are you waying that, when the greatest year that has :given_period also has period='00' (or '0', or whatever you want to use), then you want to double the budget from the given_period (as well as subtract the budget from the '00', and not count the pevious year's '14')? If so, add another condition to the CASE statement which decides what you're SUMming:
WITH got_greatest_year AS
SELECT TO_NUMBER (fgl_grnt_year) AS grnt_year
, fgl_period
, TO_NUMBER (fgl_budget) AS budget
, MAX ( CASE
WHEN fgl_period = :given_period
THEN TO_NUMBER (fgl_grnt_year)
END
) OVER () AS greatest_year
FROM fgl
, got_cnt_00 AS
SELECT grnt_year
, fgl_period
, budget
, greatest_year
, COUNT ( CASE
WHEN grnt_year = greatest_year
AND fgl_period = '00'
THEN 1
END
) OVER () AS cnt_00
FROM got_greatest_year
SELECT SUM ( CASE
WHEN grnt_year = greatest_year -- New
AND fgl_period = :given_period -- New
AND cnt_00 > 0 THEN budget * 2 -- New
WHEN grnt_year = greatest_year
AND fgl_period = :given_period THEN budget
WHEN grnt_year = greatest_year
AND fgl_period = '00' THEN -budget
WHEN grnt_year = greatest_year - 1
AND fgl_period = '14'
AND cnt_00 = 0 THEN budget
END
) AS total_budget
FROM got_cnt_00
;You'll notice this is the same as the previous query I posted, except for 3 lines maked "New". -
Need Help With File Matching Records
I need help with my file matching program.
Here is how it suppose to work: FileMatch class should contain methods to read oldmast.txt and trans.txt. When a match occurs (i.e., records with the same account number appear in both the master file and the transaction file), add the dollar amount in the transaction record to the current balance in the master record, and write the "newmast.txt" record. (Assume that purchases are indicated by positive amounts in the transaction file and payments by negative amounts.)
When there is a master record for a particular account, but no corresponding transaction record, merely write the master record to "newmast.txt". When there is a transaction record, but no corresponding master record, print to a log file the message "Unmatched transaction record for account number ..." (fill in the account number from the transaction record). The log file should be a text file named "log.txt".
Here is my following program code:
// Exercise 14.8: CreateTextFile.java
// creates a text file
import java.io.FileNotFoundException;
import java.lang.SecurityException;
import java.util.Formatter;
import java.util.FormatterClosedException;
import java.util.NoSuchElementException;
import java.util.Scanner;
import org.egan.AccountRecord;
import org.egan.TransactionRecord;
public class CreateTextFile
private Formatter output1; // object used to output text to file
private Formatter output2; // object used to output text to file
// enable user to open file
public void openTransFile()
try
output1 = new Formatter("trans.txt");
catch (SecurityException securityException)
System.err.println("You do not have write access to this file.");
System.exit(1);
} // end catch
catch (FileNotFoundException filesNotFoundException)
System.err.println("Error creating file.");
System.exit(1);
} // end method openTransFile
// enable user to open file
public void openOldMastFile()
try
output2 = new Formatter("oldmast.txt");
catch (SecurityException securityException)
System.err.println("You do not have write access to this file.");
System.exit(1);
} // end catch
catch (FileNotFoundException filesNotFoundException)
System.err.println("Error creating file.");
System.exit(1);
} // end method openOldMastFile
// add transaction records to file
public void addTransactionRecords()
// object to be written to file
TransactionRecord record1 = new TransactionRecord();
Scanner input1 = new Scanner(System.in);
System.out.printf("%s\n%s\n%s\n%s\n\n",
"To terminate input, type the end-of-file indicator",
"when you are prompted to enter input.",
"On UNIX/Linux/Mac OS X type <ctrl> d then press Enter",
"On Windows type <ctrl> z then press Enter");
System.out.printf("%s\n%s",
"Enter account number (> 0) and amount.","? ");
while (input1.hasNext()) // loop until end-of-file indicator
try // output values to file
// retrieve data to be output
record1.setAccount(input1.nextInt()); // read account number
record1.setAmount(input1.nextDouble()); // read amount
if (record1.getAccount() > 0)
// write new record
output1.format("%d %.2f\n", record1.getAccount(), record1.getAmount());
} // end if
else
System.out.println("Account number must be greater than 0.");
} // end else
} // end try
catch (FormatterClosedException formatterClosedException)
System.err.println("Error writing to file.");
return;
} // end catch
catch (NoSuchElementException elementException)
System.err.println("Invalid input. Please try again.");
input1.nextLine(); // discard input so user can try again
} // end catch
System.out.printf("%s %s\n%s", "Enter account number (> 0) ",
"and amount.","? ");
} // end while
} // end method addTransactionRecords
// add account records to file
public void addAccountRecords()
// object to be written to file
AccountRecord record2 = new AccountRecord();
Scanner input2 = new Scanner(System.in);
System.out.printf("%s\n%s\n%s\n%s\n\n",
"To terminate input, type the end-of-file indicator",
"when you are prompted to enter input.",
"On UNIX/Linux/Mac OS X type <ctrl> d then press Enter",
"On Windows type <ctrl> z then press Enter");
System.out.printf("%s\n%s",
"Enter account number (> 0), first name, last name and balance.","? ");
while (input2.hasNext()) // loop until end-of-file indicator
try // output values to file
// retrieve data to be output
record2.setAccount(input2.nextInt()); // read account number
record2.setFirstName(input2.next()); // read first name
record2.setLastName(input2.next()); // read last name
record2.setBalance(input2.nextDouble()); // read balance
if (record2.getAccount() > 0)
// write new record
output2.format("%d %s %s %.2f\n", record2.getAccount(), record2.getFirstName(),
record2.getLastName(), record2.getBalance());
} // end if
else
System.out.println("Account number must be greater than 0.");
} // end else
} // end try
catch (FormatterClosedException formatterClosedException)
System.err.println("Error writing to file.");
return;
} // end catch
catch (NoSuchElementException elementException)
System.err.println("Invalid input. Please try again.");
input2.nextLine(); // discard input so user can try again
} // end catch
System.out.printf("%s %s\n%s", "Enter account number (> 0),",
"first name, last name and balance.","? ");
} // end while
} // end method addAccountRecords
// close file
public void closeTransFile()
if (output1 != null)
output1.close();
} // end method closeTransFile
// close file
public void closeOldMastFile()
if (output2 != null)
output2.close();
} // end method closeOldMastFile
} // end class CreateTextFile--------------------------------------------------------------------------------------------------
// Exercise 14.8: CreateTextFileTest.java
// Testing class CreateTextFile
public class CreateTextFileTest
// main method begins program execution
public static void main( String args[] )
CreateTextFile application = new CreateTextFile();
application.openTransFile();
application.addTransactionRecords();
application.closeTransFile();
application.openOldMastFile();
application.addAccountRecords();
application.closeOldMastFile();
} // end main
} // end class CreateTextFileTest-------------------------------------------------------------------------------------------------
// Exercise 14.8: TransactionRecord.java
// A class that represents on record of information
package org.egan; // packaged for reuse
public class TransactionRecord
private int account;
private double amount;
// no-argument constructor calls other constructor with default values
public TransactionRecord()
this(0,0.0); // call two-argument constructor
} // end no-argument AccountRecord constructor
// initialize a record
public TransactionRecord(int acct, double amt)
setAccount(acct);
setAmount(amt);
} // end two-argument TransactionRecord constructor
// set account number
public void setAccount(int acct)
account = acct;
} // end method setAccount
// get account number
public int getAccount()
return account;
} // end method getAccount
// set amount
public void setAmount(double amt)
amount = amt;
} // end method setAmount
// get amount
public double getAmount()
return amount;
} // end method getAmount
} // end class TransactionRecord -------------------------------------------------------------------------------------------------
// Exercise 14.8: AccountRecord.java
// A class that represents on record of information
package org.egan; // packaged for reuse
import org.egan.TransactionRecord;
public class AccountRecord
private int account;
private String firstName;
private String lastName;
private double balance;
// no-argument constructor calls other constructor with default values
public AccountRecord()
this(0,"","",0.0); // call four-argument constructor
} // end no-argument AccountRecord constructor
// initialize a record
public AccountRecord(int acct, String first, String last, double bal)
setAccount(acct);
setFirstName(first);
setLastName(last);
setBalance(bal);
} // end four-argument AccountRecord constructor
// set account number
public void setAccount(int acct)
account = acct;
} // end method setAccount
// get account number
public int getAccount()
return account;
} // end method getAccount
// set first name
public void setFirstName(String first)
firstName = first;
} // end method setFirstName
// get first name
public String getFirstName()
return firstName;
} // end method getFirstName
// set last name
public void setLastName(String last)
lastName = last;
} // end method setLastName
// get last name
public String getLastName()
return lastName;
} // end method getLastName
// set balance
public void setBalance(double bal)
balance = bal;
} // end method setBalance
// get balance
public double getBalance()
return balance;
} // end method getBalance
// combine balance and amount
public void combine(TransactionRecord record)
balance = (getBalance() + record.getAmount());
} // end method combine
} // end class AccountRecord -------------------------------------------------------------------------------------------------
// Exercise 14.8: FileMatch.java
import java.io.File;
import java.io.FileNotFoundException;
import java.lang.IllegalStateException;
import java.util.NoSuchElementException;
import java.util.Scanner;
import java.util.Formatter;
import java.util.FormatterClosedException;
import org.egan.AccountRecord;
import org.egan.TransactionRecord;
public class FileMatch
private Scanner inTransaction;
private Scanner inOldMaster;
private Formatter outNewMaster;
private Formatter theLog;
// enable user to open file
public void openTransFile()
try
inTransaction = new Scanner(new File("trans.txt"));
} // end try
catch (FileNotFoundException fileNotFoundException)
System.err.println("Error opening file.");
System.exit(1);
} // end catch
} // end method openTransFile
// enable user to open file
public void openOldMastFile()
try
inOldMaster = new Scanner(new File("oldmast.txt"));
} // end try
catch (FileNotFoundException fileNotFoundException)
System.err.println("Error opening file.");
System.exit(1);
} // end catch
} // end method openOldMastFile
// enable user to open file
public void openNewMastFile()
try
outNewMaster = new Formatter("newmast.txt");
catch (SecurityException securityException)
System.err.println("You do not have write access to this file.");
System.exit(1);
} // end catch
catch (FileNotFoundException filesNotFoundException)
System.err.println("Error creating file.");
System.exit(1);
} // end method openNewMastFile
// enable user to open file
public void openLogFile()
try
theLog = new Formatter("log.txt");
catch (SecurityException securityException)
System.err.println("You do not have write access to this file.");
System.exit(1);
} // end catch
catch (FileNotFoundException filesNotFoundException)
System.err.println("Error creating file.");
System.exit(1);
} // end method openLogFile
// update records
public void updateRecords()
TransactionRecord transaction = new TransactionRecord();
AccountRecord account = new AccountRecord();
try // read records from file using Scanner object
System.out.println("Start file matching.");
while (inTransaction.hasNext() && inOldMaster.hasNext())
transaction.setAccount(inTransaction.nextInt()); // read account number
transaction.setAmount(inTransaction.nextDouble()); // read amount
account.setAccount(inOldMaster.nextInt()); // read account number
account.setFirstName(inOldMaster.next()); // read first name
account.setLastName(inOldMaster.next()); // read last name
account.setBalance(inOldMaster.nextDouble()); // read balance
if (transaction.getAccount() == account.getAccount())
while (inTransaction.hasNext() && transaction.getAccount() == account.getAccount())
account.combine(transaction);
outNewMaster.format("%d %s %s %.2f\n",
account.getAccount(), account.getFirstName(), account.getLastName(),
account.getBalance());
transaction.setAccount(inTransaction.nextInt()); // read account number
transaction.setAmount(inTransaction.nextDouble()); // read amount
else if (transaction.getAccount() != account.getAccount())
outNewMaster.format("%d %s %s %.2f\n",
account.getAccount(), account.getFirstName(), account.getLastName(),
account.getBalance());
theLog.format("%s%d","Unmatched transaction record for account number ",transaction.getAccount());
} // end while
System.out.println("Finish file matching.");
} // end try
catch (NoSuchElementException elementException)
System.err.println("File improperly formed.");
inTransaction.close();
inOldMaster.close();
System.exit(1);
} // end catch
catch (IllegalStateException stateException)
System.err.println("Error reading from file.");
System.exit(1);
} // end catch
} // end method updateRecords
// close file and terminate application
public void closeTransFile()
if (inTransaction != null)
inTransaction.close();
} // end method closeTransFile
// close file and terminate application
public void closeOldMastFile()
if (inOldMaster != null)
inOldMaster.close();
} // end method closeOldMastFile
// close file
public void closeNewMastFile()
if (outNewMaster != null)
outNewMaster.close();
} // end method closeNewMastFile
// close file
public void closeLogFile()
if (theLog != null)
theLog.close();
} // end method closeLogFile
} // end class FileMatch-------------------------------------------------------------------------------------------------
// Exercise 14.8: FileMatchTest.java
// Testing class FileMatch
public class FileMatchTest
// main method begins program execution
public static void main( String args[] )
FileMatch application = new FileMatch();
application.openTransFile();
application.openOldMastFile();
application.openNewMastFile();
application.openLogFile();
application.updateRecords();
application.closeLogFile();
application.closeNewMastFile();
application.closeOldMastFile();
application.closeTransFile();
} // end main
} // end class FileMatchTest-------------------------------------------------------------------------------------------------
Sample data for master file:
Master file
Account Number Name Balance
100 Alan Jones 348.17
300 Mary Smith 27.19
500 Sam Sharp 0.00
700 Suzy Green -14.22Sample data for transaction file:
Transaction file Transaction
Account Number Amount
100 27.14
300 62.11
300 83.89
400 100.56
700 80.78
700 1.53
900 82.17 -------------------------------------------------------------------------------------------------
My FileMatch class program above has bugs in it.
The correct results for the newmast.txt:
100 Alan Jones 375.31
300 Mary Smith 173.19
500 Sam Sharp 0.00
700 Suzy Green 68.09The correct results for the log.txt:
Unmatched transaction record for account number 400Unmatched transaction record for account number 900------------------------------------------------------------------------------------------------
My results for the newmast.txt:
100 Alan Jones 375.31
300 Mary Smith 111.08
500 Sam Sharp 0.00
700 Suzy Green -12.69My results for the log.txt
Unmatched transaction record for account number 700-------------------------------------------------------------------------------------------------
I am not sure what is wrong with my code above to make my results different from the correct results.
Much help is appreciated. Please help.From the output, it looks like one problem is just formatting -- apparently you're including a newline in log entries and not using tabs for the newmast output file.
As to why the numbers are off -- just from glancing over it, it appears that the problem is when you add multiple transaction values. Since account.combine() is so simple, I suspect that you're either adding creating transaction objects incorrectly or not creating them when you should be.
Create test input data that isolates a single case of this (e.g., just the Mary Smith case), and then running your program in a debugger or adding debugging code to the add/combine method, so you can see what's happening in detail.
Also I'd recommend reconsidering your design. It's a red flag if a class has a name with "Create" in it. Classes represent bundles of independant state and transformations on that state, not things to do.
Maybe you are looking for
-
Equim A210 - Keyboard not working right
Had major problems with laptop, so did a full rebbot with repair disc, but now laptop keyboard isn't working right. If i type the letter O i get LO, and if i type the letter L i get OL, the letter E acts just as the enter button does, and if i press
-
Bizzare error - datasource and getdate not returning correct day of week
Hi, This is on CFMX 7.0.2,142559. I have a data source pointing to a MS SQL server. There is a simple query that access a date off the database and extract the values of: -. Current timestamp -. Day of week -. First day of week The query has been run
-
hi all, while i am creating sales order in exports when i enter the conditins like BASE PRICE,FRIEGHT, then it is working fine. it is showing the total net value properly. But, as soon as i enter INSURANCE condition then it is clearing the net amount
-
hi, I am workign on BI7.0/SP09. There are many process chains running in my system daily, but not able to capture the process chain statistics (Cube is 0TCT_C22). When ran datasource 0TCT_DS21 in t-code RSA3, it shows no records extracted. Now unlike
-
How to add members to aclGroupAddr without being ldap directory manager?
Shared mail folders can be shared to a group e.g [email protected], how does one allow a delegated administrator to define the members of the group. I assumed that it referred to a group created in DA, but the value aclGroupAddr does not get updated