Need help with Dual Channel DDR memory

Hi, I have a msi nvidia MOBO, K7N2G and it supports dual channel memory. The manual says to put one in 1 and one in 3. I did then it wont start. System gives the old beep.........beep.........beep. I have to patriot 512 ddr sticks. They work fine in slot 1 and 2 but not in "dual channel" mode. Do i have to do anything else in order to get these to work?? Any assistance would be greatly appreciated. Thanks

hi
try slot 2&3.
what brand of memory?
what speed is the memory working in?
there is no option to disable or enable dual channel.
just put them in slot 1&3 or 2&3.
bye

Similar Messages

865P Neo With Dual Channel DDR

I just got my Crucial 2x256 DDR400/PC3200 ram modules today and installed them and they are working fine. When I bootup it says "Dual Channel/Linear." My question is what would be the best way to overclock this computer. I have an Intel 2.8GHZ processor with an 800MHZ FSB. I tried using Fuzzy Logic to auto overclock the computer but it just locks up. It didn't start locking up until I installed this ram. I was wondering if Core Center would overclock or just what would be the best way to overclock this computer. I want to be able to reach 3ghz. Please reply I appreciate anyone's help.

Hi adamcn20,
Hmmm... To me... the Best way to o/c a system is always thru BIOS settings... As now you are running DDR 400 RAMs, be sure that you've set your settings to CAS 2-2-2-5/7-8burst and make sure that if you want stability lower them to run at 333MHz if not be sure that you've loosen enough stress off your RAMs at 400MHz...
All the Best... :D!!!

New logic user, need help with multi-channel inst and aux strips.

Greetings all,
So I just purchased a new Mac Pro 2.66 and Logic Pro 7 to run with it. I have been a long time Nuendo/Cubase user on the PC side of things but since I got the Mac I wanted a DAW that was supported fully for the apple platform.
Anyways, its a world of difference and I am very confused as I wrap my head around the learning curve, so in the meantime I have one important question maybe some one could help me with.
The question is regarding Aux channel stips for Multi channel instruments. In this scenario I am working with Battery 3, it took me a while to understand that I actually needed to create these aux channels just to have seperate outs in Battery which seems really wierd and overly time consuming.
As an example in Nuendo once you create the instance of Battery, the audio mixer automatically just creates the corresponding stereo and mono channels instantly. This obviously makes is a sinch to assign Batteries pads to seperate outs for eq/comps for seperate sounds.
Now the Battery manual doesnt even make a reference to Aux channels for assigning outs in Logic, I actually had to do a Google search to figure this out.
Anways, sorry for rambling...
Here is the main issue.... How can I quickly and easily create multiple Aux's? In the mixer there is really only enough room in there to add like 1 more Aux strip, if I want to add more than that I need to re-arrange the entire global mixer which seems like a crazy system, surely there must be a more convenient method for getting muti-channel audio instruments set up quicker.
Any help you can assist with would be exceptional!
Thanks in advance.

Not sure what exactly your question is, especially since I don't use battery. But as far as creating aux tracks:
• go to the audio layer of the environment (not the track mixer window), find the two defalt aux tracks
• Highlight all tracks to the right of the aux tracks (these should be bus and output tracks), and drag to the right far enough to fit in a bunch of aux tracks; you might even want to drag the all underneath the aux tracks, if your screen accomodates
• use the key command shift-command-a multiples times to create several new "audio objects", and double click each one to expand
• highlight all the new objects and select options/clean up/ align objects (makes it look nicer)
• still highlighted, over in the parameters section (left side) select a channel, setting it to the highest number aux (at this point, probably "aux 3")
• now individual set the channel for each aux track – you'll see that now you have available "aux 4"; next time you set a successive track you'll see "aux 5" and so on
• once you've got things set up the way you want, save it as a template so you don't have to do this again later

Need help with dual slider

Hi everyone, I am a flash designer new to flex, i know that
Flex is geared more towards coders than designers, but i have a
pretty good grasp on how to work w/ flex and as3. usually if i find
some example i can mold my project after that. anyways here's my
problem: i found a dual slider component by
Brendan
Meutzner and have it working great. what i need is for its
change event to affect a grid of items in an xml file based on
price. i know i need to put these items in an array collection.
however, i found the adobe
FlexStore
and realized i could download the source by right clicking on it.
in the products section there is the code and everything i need to
make my project work (the slide updates visible products based on
their price) but my problem is it only works the first time(if you
move the slider you will see it update the product view but only
from the initial values that wee set). here is a
LINK
to my files (with sourceview enabled) so if anyone can help me out,
it would be much appreciated. feel free to email me,
[email protected]
if you need any more info to help me out. thanks!

Thanks NED!
that was it... I got the code below working.
stop();
maskee.cacheAsBitmap = true;
vol_slider.cacheAsBitmap = true;
maskee.mask = vol_slider;
stage.addEventListener(Event.ENTER_FRAME,myFunction);
function myFunction(event:Event) {
vol_switch.x = vol_slider.x;
function startDragHandler(evt:MouseEvent):void {
vol_slider.startDrag(false, new Rectangle(2, 0, 298, 0));
stage.addEventListener(MouseEvent.MOUSE_UP, stopDragHandler);
function stopDragHandler(evt:MouseEvent):void {
vol_slider.stopDrag();
stage.removeEventListener(MouseEvent.MOUSE_UP, stopDragHandler);
vol_switch.buttonMode = true;
vol_switch.addEventListener(MouseEvent.MOUSE_DOWN, startDragHandler);

Need Help with 266 (tray type) Memory upgrade

Greetings All:
I have obtained my first Mac: an iMac 266 (the CD tray load type). I have replaced the hard drive and am now working on the RAM memory. I see the the "upper" slot. I'm guessing the "lower" slot is under the circuit board that fills the metal cage with the processer chip (?). If this is true any suggestions on how to remove it? I removed the one screw on the outside corner but removing the cage is very stubborn so I'm holding off continuing until I get some advice on this.
Thanks.
imac 266 Mac OS 9.1.x

check out http://www.djonmac.com/ it should hopefully be helpful. I remember it being a bit stubborn when I did my ram upgrade.

Need help with dual monitor setup for KDE 3.5.5.

Here's my hardware:
NEC MultiSync LCD 1530V: 1024x768 (analog)
Samsung SyncMaster 941BW: 1440x900 (digital)
nVidia Dual head AGP video card.
The dual monitor works under dual-boot Windows, boot up and pure Linux console. I've googled around for help, changed my xorg.conf file accordingly to some sites, but it wasn't much help.
Here's my working xorg.conf:
Section "ServerLayout"
Identifier "Simple Layout"
Screen "Screen 1" 0 0
InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"
EndSection
Section "Files"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/75dpi"
FontPath "/usr/share/fonts/100dpi"
FontPath "/usr/share/fonts/Type1"
EndSection
Section "Module"
Load "dbe" # Double buffer extension
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
Load "freetype"
Load "glx"
EndSection
Section "InputDevice"
Identifier "Keyboard1"
Driver "kbd"
Option "AutoRepeat" "500 30"
Option "XkbRules" "xorg"
Option "XkbModel" "pc101"
Option "XkbLayout" "us"
EndSection
Section "InputDevice"
Identifier "Mouse1"
Driver "mouse"
Option "Protocol" "Auto" # Auto detect
Option "Device" "/dev/input/mice"
EndSection
Section "Monitor"
Identifier "NEC LCD1530V"
HorizSync 31.5 - 48.5
VertRefresh 50.0 - 70.0
EndSection
Section "Device"
Identifier "Standard VGA"
Driver "vga"
VendorName "Unknown"
BoardName "Unknown"
EndSection
Section "Device"
Identifier "NVIDIA GeForce"
Driver "nvidia"
Option "NoLogo" "true"
EndSection
Section "Screen"
Identifier "Screen 1"
Device "NVIDIA GeForce"
Monitor "NEC LCD1530V"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 8
Modes "1024x768"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
Modes "1024x768"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1024x768"
EndSubSection
EndSection
Using this xorg.conf file, only my NEC LCD analog monitor could display KDE while the Samsung digital can't.
Any suggestions?

Thanks for your help guys, I'm halfway there.
The second monitor shows the KDE desktop, but it isn't exactly what I expected. Right now, both monitors display at 1024x768 (each) or 2048x768 (total). The larger monitor stretches and distorts the display of 1024x768 to its natural resolution at 1440x900 and it isn't what I wanted. Other than that, the dual desktop setup behaves what I expected to.
Here's a snippet of my xorg.conf that currently works:
Section "Monitor"
Identifier "NEC LCD1530V"
HorizSync 31.5 - 48.5
VertRefresh 50.0 - 70.0
EndSection
Section "Monitor"
Identifier "Samsung SyncMaster"
HorizSync 31.5 - 60
VertRefresh 60.0 - 70.0
EndSection
Section "Device"
#VideoRam 131072
# Insert Clocks lines here if appropriate
Identifier "NVIDIA GeForce"
Driver "nvidia"
Option "NoLogo" "true"
Option "TwinView" "true"
Option "TwinViewOrientation" "LeftOf"
Option "SecondMonitorHorizSync" "30-50"
Option "SecondMonitorVertRefresh" "60"
# Option "MetaModes" "1440x900, 1440x900; 1024x768, 1024x768"
EndSection
Section "Screen"
Identifier "Screen 1"
Device "NVIDIA GeForce"
Monitor "NEC LCD1530V"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 8
Modes "1024x768"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
Modes "1024x768"
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1024x768"
EndSubSection
EndSection
Section "Screen"
Identifier "Screen 2"
Device "NVIDIA GeForce"
Monitor "Samsung SyncMaster"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 8
Modes "1440x900"
EndSubSection
EndSection
Anyone have an idea?
EDIT: Oh snaps. I just did a pacman -Syu and it upgraded Arch Linux to 0.8 and the 2nd monitor stopped working.

Need help with dual drives on Mini

I just replaced my main drive with a 750GB drive and installed a second drive a 64GB SSD on my 2011 Mac Mini. So when I booted it I installed Lion OS on the SSD and cloned my old 500GB to my new 750GB drive. I only want to have the OS, Lightroom and Photoshop installed on the SSD.
So here are some questions.
1. Can I just drag and drop LR and PS to the SSD and they will work?
2. How can I make everything I download or install go to the 750GB drive automaticly?
3. How do I get all my apps to show up in the App file on the SSD drive but still keep them installed on the 750GB drive?
4. How do I remove the OS off of my 750GB drive to free up space?
I want to try to get most of these questions resolved before I install Mountain Lion.

1. Likely, but they'll still be looking for & using the Drive they were installed on for other components & settings.
2. You can set the Download folder in Safari>Preferences General, on Installs you'll have to choose the Install Disk.
3. Find the Applications folder on the 750, drag it to the Right Side of the Dock.
4. Not easy without erasing.
Are you sure you want/need iOS8?

Need help with dual display configuration

I have just connected a HD, widescreen monitor to my Mac tower and am having trouble getting video from FCP to show up on it. It's connected to the mini port and is displaying the same desktop image as my primary monitor but I can't seem to get it to display the video when editing. What am I missing?

The "mirror" box was already unchecked. The best I could get after trying every conceivable combination was just one frame at a time whenever I stopped playing the timeline. The screen then refreshes to show whatever that last frame is, but it will not play the video, it just displays the very last frame.

Quick help with dual booting

I have hopped around on different distros and I found that Archlinux would be the best solution for me. However, I need help with dual booting Archlinux and Vista as I will need Vista around for one program and a game that do not work with any Linux distro that I have tried. I have not done a text based install before, I have only used newbie distros but I want to move on to Archlinux.
I will only need one partition for Vista and one for Arch. I believe I can achieve the goal of dual booting them by shrinking the vista partition, and then installing Arch in the remaining space and use GRUB to boot the necessary partitions when my laptop is powered on. This works with Ubuntu, so I assume it shall be the same basic concept with Arch. I can follow the instructions on installing, and the installation is easier than I had expected it to be. I have one question, how would I go about using the above technique that I mentioned during the install? I would like to know how to do it correctly, I cannot risk messing up Vista. I'm fifteen and my dad would be very frustrated if I did mess up Vista. I would appreciate some specific instructions, because I really like Arch from what I have read. I also look forward to being an active member in the community as well if all goes well.

Welcome!
Another young one I see! I'm currently 17, however I started using linux when I was 13 (8th grade year).
You can resize the vista partition by using gparted. You can download the gparted livecd from there website (http://gparted.sourceforge.net/download.php). I do not know specific directions, but it is pretty obvious how to resize, and if you need help you can probably google something like "resize partition gparted". I WARN YOU that you do risk data loss resizing the partition. I don't believe the risk is high, but it still there, so backup any important data that you may have in case something goes wrong!!
Do you have your own computer that you can experiment on? That might be a safe option than using your dads. I am been fortunate to have hand-me-down systems, but when I was young I made my dad angry quite a few times "experimenting!"
If your dad's system has enough juice, you may want to consider install arch in a virtual machine to get idea of however thing works. Following the Beginners Guide on the wiki will be you best bet for a successful and well configured machine (http://wiki.archlinux.org/index.php/Beginners_Guide). If you really want to play it safe you can even go as far as install windows in a virtual machine, resizing the partition, and installing arch in the same virtual machine.
I hate to say this, but if you absolutely can not mess up vista, I would advice against installing any other OS and messing with the partition scheme. As whenever you mess with the partitions you run a risk of messing up Vista (or any other os for that matter). If you don't already have your own computer which you can tinker with, it might not be a bad idea to look at getting one. They are becoming cheap, you can build one for about $300-$400USD, or buy one for probably around $400.
Hope this helps a bit...

Dual Channel DDR Vs. DDR Memory, etc.

So I'm in the process of upgrading again and was hoping to add a little more memory to my system. With all the different types of memory out there it starts to become a little confusing as to how much bang your going to get for your buck and the pitfalls of marketing ?( . Currently i'm looking into Dual Channel DDR since this is the new craze. I currently have 1 512MB stick of PC3200 DDR memory that I plan on replacing with 1GB (2) sticks of Dual Channel DDR PC3700 or PC4000. The difference is 60 bucks and I'm wondering...is it worth the extra cash for PC4000? It's Corsair memory which I currently have never had problems with but it is a little pricier than the generic memory out there.
Is it possible that the only reason to do something like this would be overclocking or is my system going to use the full extent I give it (Or am I putting myself in line so that my memory will be able to support future cpu, etc. upgrades). My specs are below, feel free to ask questions. I appreciate any replies in advance. )
Thanks again,
-MaD

Quote
Originally posted by Assaf
With both sticks in the same channel your not using dual channel.
A bios update could fix the RAM compatability problem.
So i\'ve been getting alot of crashes since i purchased this board but more so when I installed the new memory. This last round produced another error message that was logged with microsofts OCR tool. The debug information was submitted and handed back as a memory problem. I downloaded their DOS memory tool to test memory and tried the motherboard with a bunch of different configurations. Here\'s what I found:
4 different sticks of memory at any configuration produced Failures on WMATS+, WINVC and would eventually lockup the system.
I went to the processor....
3 different processors all generated failures with any of the same memory configurations.
I tested all memory sticks in a different system with no failure. It ran 5 passes and even an extended test without failure.
I disconnected my drives from the MB (currently running disk striping on IDE 3, not sure if that is even effective since they are both on the same ide channel. What's up with only one?? and 2 for SATA) and ran the same tests with the memory and none have failed. If i connect the drives and turn of the RAID bios once again all tests + extended pass.
So leads to my question...How do I fix this? I was running a Soyo P4X400 before with Disk striping on two seperate channels and I wanted to bring that same performance to this board. Not sure though if i\'m getting that though...let alone the current problem it has with memory when it\'s enabled.
Any help is appreciated, I dont mind being the Gunnuie pig if it helps other people in the process. I\'m just happy i dont have bad RAM, CPU, and possible the board. )

Need help with bios settings for Neo4 Platinum

Hi. I've checked several guides on bioses and still have questions about my settings. I'm not an overclocker, so I'm looking for stability over anything else (although I don't want my computer to run like a pig . I'll post what I have and the parts of the bios that I'm unsure of. I also have saved pictures of a Cpu-z scan if that helps. Any suggestions are much appreciated!
Here's my stuff:
Motherboard: MSI K8N NEo4 Platinum (MS-7125)
Processor: AMD Athlon 64 3000+ 512K 90nm (Winchester socket 939)
   clock frequency: 1800mhz
   system bus: 2000
   operating mode: 32/64
   voltage: 1.40v
   max temp: 70 degrees C
   thermal power: 89w
   L1 cache: 128KB
   L2 cache: 512KB
   cmos technology: 90nm SOI
   memory controller: 128-bit
Award bios version: 1.9
Installed ram: Micron Crucial Ballistix 512MBx2 (1024MB total) (Crucial
part number BL6464Z402)
   PC3200 400mhz Dual-Channel DDR Dimm (184 pins)
   configuration: 64Meg x 64
   unbuffered/non-ecc
   voltage: 2.8v
   memory timings:   2-2-2-6
Here's my current bios settings (I've only listed sections that contained settings that I was unsure of):
ADVANCED BIOS FEATURES
quick booting: enabled
boot to os/2: no
ioapic function: enabled
mps table version: 1.4
full screen logo display: disabled
seek floppy: enabled
typematic rate setting: enabled
typematic rate: 30
typematic delay: 1000
security option: setup
ADVANCED CHIPSET FEATURES
--->>DRAM CONFIGURATION
timing mode: manual
memclock index value: 200mhz
cas# latency TCL:2
min ras# active time TRAS: 6t
ras# to cas# delay TRCD: 2t
row precharge time TRP: 2t
row to row delay TRRD: auto
row cycle time TRC: 8t
row refresh cyc time TRFC: 11t
read-to-write time TRWT:auto
write recovery time TWR:auto
write to read delay: TWTR:auto
refresh period TREF:auto
user config mode: auto
x bottom of 32-bit [31:24] io: D8
x 1t/2t memory timing: 2t
x read preamble value: 8ns
x async latency value: 9ns
s/w memory hole remapping: disabled
mtrr mapping mode: continuous
PNP/PCI CONFIGURATIONS
primary graphic's adapter: first pcie
resources controlled by: auto (escd)
x irq resources setup: press enter
maximum payload size: 4096
CELL MENU
current cpu clock: 1810 mhz
current ddr clock: 201 mhz
high performance mode: manual
aggressive timing: disabled
dynamic overclocking: disabled
adjust cpu fsb frequency: 200
ht frequency: 5x
ht width: (down arrow 16/up arrow 16)
cpu spread spectrum: disabled
sata spread spectrum: disabled
pcie spread spectrum: disabled
pcie clock: 100 mhz
sse/sse2 instructions: enabled
cool'n'quiet: disabled
adjust cpu vid: startup
extra cpu voltage: by cpu vid
cpu voltage 1.400v
memory voltage: auto
nf4 voltage: 1.50v
Thanks again. xpfshost

I'll do that, thanks. I guess I'm really mostly clueless about the following items:
memclock index value: 200mhz
row cycle time TRC: 8t
row refresh cyc time TRFC: 11t
current cpu clock: 1810 mhz
current ddr clock: 201 mhz
adjust cpu fsb frequency: 200
ht frequency: 5x
ht width: (down arrow 16/up arrow 16
pcie clock: 100 mhz
Do they look OK?? Thanks!
xpfshost
Quote from: Grayone on 19-April-07, 05:13:03
Change your user config mode in dram configuration to manual and change your memory timing to 1T. The 1T setting will speed up your memory slightly.

Need help with ram on bootcamp

hey guys i need help with getting more ram on the pc side of bootcamp.
it says i have 1.99 of ram on the pc side
then on the mac i got this
Model Name: Mac Pro
Model Identifier: MacPro1,1
Processor Name: Dual-Core Intel Xeon
Processor Speed: 2 GHz
Number Of Processors: 2
Total Number Of Cores: 4
L2 Cache (per processor): 4 MB
Memory: 4 GB
wanting to know how to get more ram over to boot camp

Rodney:
You cannot physically or via software add/move RAM from OSx side to Windows side. This is because you run Leopard and Windows separately and therefore when one is running the other is not active. The only thing that controls how much RAM Windows sees/uses is determined by the type of Windows you have installed (32BIT or 64BIT). Please do not confuse that with Gigabytes of RAM or disk space.
32BIT Windows has a maximum limit of 3GB of RAM (it often uses only around 2GB of RAM when it is sharing the system RAM with your video card. I believe this is the case with you.
64BIT Windows will be able to sees/use all of your 4GB of RAM.
Leopard sees/uses all of your 4GB of RAM.
If you have installed Windows XPSP2 and it is working properly on your boot camp partition then I can assure you that it is the 32BIT version.
FYI - The only time that one can select/decide how much RAM Leopard uses and how much RAM Windows uses is when one is running Windows as a Virtual Machine under software such as Fusion or Parallels. I have assumed that you are running windows on a boot camp partition (from your posts) and therefore this does not apply to you.
Axel F.

MOVED: need help with my k7n2 delta series motherboard please

This topic has been moved to AMD SocketA based board.
need help with my k7n2 delta series motherboard please

"...the other memory ive been using is memorymaxx 512mb ddr 3200..." If I understood right, your'e actually using both memories at same time so, your'e lucky if it works. We have said thousand times that mixing dif. brand/make/speed memories is a bad idea, most with this Mobo that is very picky about ram. If you want to avoid slowdown problems, stay with only one stick ( the better one ) until you can buy at same time in same store, 2 identical memories to replace the old one.

Random Reboots with dual channel

Hi,
I just bought yesterday the following system.
Intel P4 2.8 Northwood HP enabled
MSI 865PE/Neo 2 Platinum Edition
Maxtor Diamond Star 9 200 GB 8MB Cache 7200rpm
Elixir 2x512MB DDR 400 CL3
Toshiba DVD 16x
Creative Geforce 4 Ti 4400 128MB
Logitech Cordless Keyboard connected and a logitech cordless optical mouse
19 inch belinea monitor.
The power supply is a no name product LPK2-30 with the following specs.
420W
3.3V 28A
+5V 36A
-5V 0.5A
+12V 17A
-12V -0.8A
It says that is P4 ready, i know which does mean nothing
Operating System:
Windows XP Professional SP1
All Hotfixes and Updates applied
Newest drivers for all the system parts
The errors during the windows crashes are irq not less or equal or page fault, which looks for me pretty much like a problem with the memory.
Ok what i tried so far.
Single channel with 512MB works fine.
Single channel with 1GB works fine except one strange thing restarting the machine and it got stuck during the bios loading worked fine after i pressed reset.
Dual channel 1/3 1 GB get random reboots.
Dual channel 2/4 1 GB even worse but i think at this point my newly installed died.
I tried to set memory voltage from 2.65 up to 2.8 but did not change the behaviour.
memtest with one modules in slot 1 no errors
memtest with dual channel 1/3 1 gb no errors running 30 minutes
i will try now a memtest with the second single module in memslot 3.
No MAT or dot ram settings are 3,3,3.
I am bit running out of ideasö
before i forget i updated the bios from 3.3 to 3.5 but did not change the problems.
Maybe you guys have some ideas what else can i try.
thx a lot in advance. i hope i provided all informations which are necessary.
greetings faxe

Hi,
i tried a few more things which make confident that i have the problem narrowed down to the memory.
i tried to install windows again with only using the third memory slot single channel and it worked fine.
now i tried to go down with the memory speed to ddr333 and using dual channel and so far that seems to work too.
so i think i will go for other memory.
if you think i am wrong please correct me
greetings markus

K8N Neo2 Platinum ( is it true its not good with dual channel?)

hi i ordered the mobo and when it came it didnt work so i sent it back
well the guy called my house and told me that he can send me the same mobo back , then he asked how i would be setting it up when i told him i had 2x sticks of 512 memory he told me that the mobo dont work well with dual channel
is this true or is he just tryin to get me to upgrade ???
thx
memory = 2x 512 mb ddr Samsung

Quote
when i told him i had 2x sticks of 512 memory he told me that the mobo dont work well with dual channel
is nearly as good as:
Quote
I called the reseller and he said it is completely normal for a computer to bomb out when running 3D.
https://forum-en.msi.com/index.php?topic=94728.msg681427#msg681427
maybe its the same person!

Need help with Dual Channel DDR memory

Similar Messages

Maybe you are looking for