Need Help with ESATA on MSI P35 Neo2-FR

I have the MSI P35 Neo2-FR motherboard http://www.msi.com/index.php?func=proddesc&maincat_no=1&cat2_no=&cat3_no=&prod_no=1261 and trying to get the eternal ESATA to work. It works with one individual HD. I'm using an external ESATA drive with 3 HD inside the external case with one cable running into the external ESATA in the back of the motherboard. It's only recognizing 1 drive and the other 2 isn't showing up. If I switch it to USB connection it will read all 3 drives. I'm running windows 7 x64 but it recognize on my other 2 computers with a different motherboard. I have install it with the ACHI setup in Bios and I've also install the Matrix Storage Controller after installation. I never install the Intel ICH9R SATA RAID driver where you have to press the F6 to install it. Is that what I'm missing and is taht needed for the ESATA to work? I'm getting this message "A storage device was connected. If this device is a port multiplier, only port 0 of the port multiplier will be active." Been googling all day and still can't figure out what I'm missing.
Any help would greatly be appreciated.

Quote
For some reason this board is Bios only have IDE, RAID and ACHI and I don't see a SATA.
IDE, RAID and AHCI are operating modes of the SATA Controller. Everything okay here.
Quote
Seems to me it's either this board and it's driver don't let you use the port multiplier but it suppose to support port multiplier.
It is neither the board, nor is it the driver. It is a limitation of the Intel ICH9R Chipset. You will have the same problem on all P35/ICH9R based mainboards. Read here:
http://xtreview.com/addcomment-id-788-view-intel-technology-matrix-RAID-and-port--multiplier.html
Quote
Unfortunately, used in the south bridges ICH9R the version of such technology provides access only to one hard disk at the specific moment of time. . The technology became more complex to realize , which implies to several access disks simultaneously, possesses higher cost and more higher central processor loads , therefore it can be rejected.
Here is the same problem on a Gigabyte GA-P35-DQ6:
http://forums.overclockers.co.uk/showthread.php?p=11892094
Nothing you can do about it.

Similar Messages

Need help with destinations.msi error

When I try to access the internet via "Firefox", I receive, the message: "Please wait while windows configures Destinations" "The feature you ae trying to use is on a cd-rom, error 1706." My PC proceeds to hang there until I cancel out the message. I'm wondering if an overzealous registry cleaner is to blame for "cleaning" something necessary out of an msi folder. What is causing this and how do I fix it?
I have a Compaq Presario SR1820NX and a HP deskjet 5440 printer running XP.

Same problem with my desktop with windows XP . When computer starts up, get windows installer popping up with same message Tried inserting Hp printer software disc, doesn't help. Then when I go to browser (firefox) get same thing again, and have to cancel, cancel cancel to get out of of it. Only way I found was to uninstall HP photosmart essential software, and leave it off. Re-installed from site as well, with no luck either. Seems to be a very widespread problem from what I can see from searching for a cure, but still haven't seen a cure that works for me. Make's it a little hard to use printer features when you can't install software for it.

Need help downgrading bios on MSI 7025 Neo2 Plat.

I have recently upgraded my bios from 1.5 to to the latest 1B version. While there are no problems in particular, it seems to have slowed down my computer in a few programs.
I have tried flashing the bios back 1.5 (and 1.8) but Windows XP now refuses to load on either versions, giving a variety of errors from corrupt system drivers to a bad BIOS... Strangely, all is fine when I upgraded back to the 1B version - does this mean I will have to reinstall Windows from scratch to use an older bios again, or is there another way around it?
Thanks!

I had similar issues with 1B and I went back to 1.5 as well. I didn't have any poblems using Syars guide... Here is the link to the winflash guide that I used:
Syar's winflash guide

Need help with brand new MSI Hawk 460GTX

I upgraded my card from an 8800GT to the 460GTX. I uninstalled the old drivers because it wouldn't POST, now it'll boot into safe mode, but starting normally my screen goes black between the Starting Windows and login screens. I still get audio, but no video. I know theres LED codes on the back of the GPU, but I can't seem to figure out what they mean. Right now the first 4 LEDs are on, but the last 2 are flickering.
setup:
Intel E8400 (3.0GHz) @ 3.6GHz
Zalman NVidia heat sink
Gigabyte GA-EP45-UD3LR
4 x 1 GB OCZ HPC Reaper RAM DDR2 1066
WD 1TB hard drive (32mb cache)
Corsair TX750W power supply
MSI Hawk 460GTX
LG Superdrive DVD/CD RW drive
The only thing I can think of is starting the computer in safe mode and downloading the drivers for it before trying to boot normally.
edit: Also, I'm getting a moving mouse cursor on the black screen but no login.

Use Driver Sweeper to remove current VGA drivers in "Safe Mode":
http://downloads.guru3d.com/Guru3D---Driver-Sweeper-%28Setup%29_d1655.html
Once done reboot and boot to normal windows mode,
then install latest drivers from:
http://www.nvidia.com/Download/index.aspx?lang=en-us

Need help with buying graphics card and ram for MSI 865PE NEO 2-V

Hi,
I want to buy 1GB of ram for motherboard MSI 865PE NEO 2-V I need help with finding correct parts.
I also want to buy 512Mb or 1GB graphics card.
as i said before i need help with finding correct ones so they match motherboard, I would appreciate if any one would post link to cheap and fitting parts.
I found graphics card allready, i just need to know if it will fit.
the card is
NVIDIA GeForce 7600 GS (512 MB) AGP Graphics Card
Thanks for help.

here you can see test reports for your mobo:
http://www.msi.com/product/mb/865PE-Neo2-V.html#?div=TestReport

MSI P35 Neo2-FR do i need JPWR1 Connected for 2 x ATI Radeon 3850 256mb cards ?

hello,
Ive recently Brought a MSI P35 Neo2-FR motherboard and been running in single Sapphire 3850 256mb so decided to install my second Sapphire 3850 256mb.
PSU Ive got is a Hyper Type M 580watt but at moment Ive used all connections 4 pin molex connections and 2 to power second sapphire 3850MB card waiting for reply from hyper about what connection i can put the extender on safely coming off 1 that's used.
Its running Stable at moment without the JPWR1 connected just wondering if its for high end cards like the 2900XT that use's a lot more power then the 3850 and 3870's
Scores I'm getting so far are with a Intel Core 2 duo E8200
Single card - 3DMark 2006 - 9436 3DMarks
Crossfire enabled - 3DMark 2006 - 12356 3DMarks
Are these scores about right too ?

Quote from: Del UK on 17-February-08, 04:42:47
Which PSU, do you use Kimpsu?
Would have a guess it's dual +12V rail......
Antec or Seasonic.......
My current PSU is an Antec NeoHE 550W (though I've had many others too, like Zalman, Seasonic and Enermax), so in theory it has three 12V rails, 18A each. Well, of course it cannot feed 18A on each rail simultaneously, but still considering that's the limit, the limit should not be a bottle-neck. Luckily they are devided logically enough, one rail for the directly attached cables (which is the motherboard really) and two for the five detachable cables. And the two rails are logically divided, so putting my PCI-e cables at both ends I get pretty decent amps for two GFX cards (one rail for each) and the motherboard. The rest (HDDs, optical drives) are then attached to cables connected next to those cables, so in fact HDDs are on one rail together with one GFX card, and optical drives (and my fan controller) is on another rail with the other GFX card. Thus I get pretty even distribution between rails (lucky me).
It was one of the nicest quiet PSUs at the time of purchase. If I were to buy a PSU now I would probably get a Corsair, probably HX520 or HX620, but they have multiple 12V rails... VX series is fine too, only that there are no detachable cables, so although it is an option, I really need to think if I wan't a PSU that only has fixed cables...
Having multiple rails suck a bit (although on most PSUs they are not really separate rails, but still current limited), but luckily single rail PSUs are coming back after a couple of years of "multi rail fashion".
And yeah, PSUs made by Seasonic are pretty popular these days, like the Antec NeoHE I have, Corsair HX series, VX450 and so on.
PS. Good guess, though guessing Antec or Seasonic covers pretty much of the PSUs out there that are of a "quality" brand, at least if Seasonic covers the PSUs made by Seasonic for other companies like Corsair. And I don't mean other suck, just judging by how large % of all quality PSUs are Antec. And yes, there are a few models from Antec that really suck and have high failure rates, and cannot be called quality (like the CWT manufactured Smartpowers and the older Truepowers, also by CWT). Judging by just the company that puts the stickers on the case is not always wise, especially with Antec...
PPS. Judging from your signature, you have an Enermax and a Corsair VX550 (which is manufactured by CWT I believe). How do you like your Corsair? Is it quiet? I've been considering it as an option to replace my Antec (I'd like to have a single 12V rail). Also the TX-series is an option.

Really need help with MSI R7970-2PMD3GD5/OC:(

Greetings to all,
I really need help with my brand new MSI R7970-2PMD3GD5/OC. I've purchased it two days ago and I didn't really have time to test the card until yesterday. The card is I think way to hot for my "liking". It idles at 56c-60c, at full load in Heaven benchmark 3.0 in 1920x1080, extreme tessellation and 8xAA card reaches 95c-97c. Stock cloacks are 1010Mhz/1375Mhz and stock voltage is 1,174v. Case is being cooled by two Noctua NF-P12 fans. Also I tried lowering the voltage and "underclocking" the card to a standard 925Mhz in small increments, but it doesn't help at all. Each and every time it results in BSOD and dx dll errors and complete system failures. Replacing the card wouldn't be a problem if I lived in a "normal" country that has access to a steady supply. Retailer that sold me a card told me that only 5 cards total have been imported from the launch day and told me that i bought the "last" card in my country. They could order a replacement but it would take them more then a month to do so.:( Ohhh and one more thing I don't overclock, everything in my case is at their default values.
Recently, I read that "Amd released" a bios update for a standard reference boards that turns them into a "GHZ editions". Also lot of users report a lower voltage requirements and lower temps with that "boost bios". As I understand this card pcb is not Amd's reference board design, I could be wrong it's not that uncommon.. So I didn't want to risk warranty by flashing it to a position 1. Will MSI release the boost bios for this model of card? I am humbly asking MSI staff on how to proceed regarding this problem. I would be immensely grateful for any help you could provide.

Quote from: Svet on 24-August-12, 18:13:26
what PC case you use exactly?
have you tried to open PC case side door and to retest?
Hi,
it's open case. If i close it the temps get even worse:(
They get better for other components, but not for gpu. Two Noctua NF-P12's are cooling the case, first one is positioned above gpu, left side next to cpu. Other is right beneath the gpu, right side of case. Just under the hdd section of the case. I tested each and every component with my backup card nv 8500gt. They function within the specified parameters. I'm getting somewhat worried.
П.С. Поздрав Свет
да ли сте ви са наших простора да не куцам на енглеском?

MOVED: Need help with msi mega 180 + athlon xp-m combo

This topic has been moved to Overclockers & Modding Corner.
Need help with msi mega 180 + athlon xp-m combo

AFAIK, you shouldn't need a pinmod for a Mobile Athlon XP CPU to work in a nforce2 mobo
did you have any other CPU installed prior to this one? if so, refer here to clear the CMOS: Clear CMOS Guide
next, refer to your manual, or download from MSI, for location of the FSB jumpers; ensure J8 is shorted across pins 1-2, and J7 is shorted
finally, enter your BIOS setup menu, and under Advanced Chipset Features, set CPU FSB to 133mhz (or even 166mhz if you have DDR333 memory). the only thing i can't see in the Mega 180 manual is where you set the multiplier...
which is where the BIOS has limited overclocking features, and you might have a problem here
i think i'll pass this over to the Overclockers forum, where someone may be able to give a better answer....

MOVED: Need help with ATI R9600PRO in MSI KT3 Ultra2

This topic has been moved to Retired motherboards.
Need help with ATI R9600PRO in MSI KT3 Ultra2

Quote from: chiochio on 21-November-05, 20:20:31
When I plugged in ATI R9600 Pro, My monitor was blank. PSU? sorry newbie .
Power Supply details..
try set AGP Vcore to 1.6

E8200 Retail with MSI P35 Neo2-FR :

Thought of sharing with the guys here.
Test Setup :
E8200 w/Intel default cooler.
Msi P35 Neo2-Fr Bios v1.1/1.81b
Corsair 6400C4DHX 2GB
Msi 8800GT 512Mb -OC Edition(Red Juliet)
Hitachi 160Gb sata
Acbel iGold 550w
Neo2/platinum Users take note.
If you are on any bios earlier than v1.6.
Do not worry, it will still boot and run fine.
You can always flash the bios later.
Here are results for coolalar.com using E8400 with P35 Neo2-Fr :
http://www.coolaler.com/forum/showthread.php?t=170745
Here's ours, but E8200.
Bios 1.1 works too.
Here are some default results of the processor :
We flashed to Bios v1.81b :
3Dmark06 : Higher cpu score
Cinebench r10 :

Pumped up some video clocks and slightly higher fsb.
511x8, 1.5v
3Dmark06 :
A final validation :
http://valid.x86-secret.com/show_oc.php?id=297680
The 6Mb is nice to have.
But if you are already using an E6750, don't think you will see much difference.
For low volts and operating temperatures,
The 45nm is good.
Ours is good at 3.6Ghz @ 1.25v(bios).
Neo2 users with more results can share here.
http://forums.hardwarezone.com/showthread.php?p=26181870
Cheers! :D

MSI P35 Neo2-FR, Im having WEIRD beeps in BIOS continiously unstopping.

Oh dear lord, i bought a new board and now im having some stupid beeps going off every 3sec in the BIOS, i updated to 1.8 bios and now its going every 1sec, BEEP BEEP BEEP BEEP BEEP BEEP BEEP BEEP BEEP, every time there is a beep the system hangs a bit, i pretty much cant do anything in BIOS and its getting on my nerves. What is causing this? I tried removing all the drives, my cpu fan is connected to molex not to the motherboard though. In windows they go away, a bit when loading windows logo and it hangs the windows logo too for a few times, then all leds go green, before im getting from top to bottom Green, Green, Green, Red, Green

• Intel Core 2 Quad Q6600 2,40GHz "SLACR G0" + ASUS Silent Knight Copper
• nVidia XFX Geforce 8800GT 512MB GDDR3 + Zalman VF-1000
• MSI P35 Neo2-FR
• 4Gb 2x2Gb A-Data PC6400 800MHz DDR2
• 1Tb 2x500Gb Samsung Sata II
• Seasonic 700W M12 Modular
• Antec Sonata II
Nothing helps, tried butting a fan into the cpu fan slot, nothing, tryed removing PCI cards, nothing, NOTHING helps, it just keeps beeping and hanging on those beeps in the BIOS. When it gets to windows load screen all is fine, the frick.
EDIT: Allright, the answer to this problem is, go to windows and do a restart from windows, go to BIOS and there is no more beeping. I did a save and exit and rewent to BIOS and still no beeping, then did the shutdown and power on to BIOS and no beeps. So, weird problem but an easy answer to fix it. I think its something to do with the motherboard booting for the first time, it just needed to go to windows and make a restart. Weeeeeiiiiird.
Cya, hope this helpes someone in the future.

MSI P35 Neo2-FR - Will this work??

Hi,
I am planning a new system, after my current one is a little dated. Here is an outline of what I am planning to build: -
CPU - Intel Core2 Quad Q6600 2.4GHz SLACR G0
M/B - MSI P35 Neo2-FR
RAM - Ballistix DDR2 PC2-8500 5-5-5-15 Unbuffered NON-ECC (4x 1GB)
G/C - INNO3D GeForce 7300GT 256MB DDR2 PCI-E
I am not needing it for gaming, but more for production work (Graphic design, Illustration and video editing).
I have a few questions if anyone can answer them for me?
Is the RAID facility on board a hardware RAID or software RAID. Since its provided by the Northbridge I am pressuming its software.
How many SATA ports can be used at any one time. For example, does using the 2x eSATA ports, reduce the amount of on board ports you can use? (Like some USB ports?).
If I wanted to use a SATA DVDRW connected to the southbridge SATA port, would I be able to boot from it?
I can see many people have had problems with installing Vista on this board, can anyone see any compatability issues with my proposed setup?
Many thanks!!!
Phil

Quote from: Hans Gruber on 28-November-07, 19:07:02
The only compatability issue would be with your 7300gt card. That's hardly enough power to run a game let alone graphics editing. You would be much better served with an 8800gt to perform video editing.
Hi Hans, the 7300 is the same card used in the Mac G5's used in my place of employment for graphic design / video editing. Although some have the 8800GT as well, this is the card used in the majority of the machines. I am sure it will be ok but you reassured one of my existing concerns. I can always upgrade this if it doesnt cut the grain!
Thankyou!!!
Quote from: Maesus on 28-November-07, 19:33:33
Please spend some time to read the moan guide if you haven't.
Yeah not much on there with regards to my post. Cheers but I did read it before I posted.
Quote from: Maesus on 28-November-07, 19:33:33
0. All of your answers are here: http://global.msi.com.tw/index.php?func=proddesc&prod_no=1261&maincat_no=1&cat2_no=170 you just need to read line by line and you shouldn't miss the answers.
was already a bookmark in my browser as I have been researching it for a while now. Just wanted clarification on a few things hence my post.
Quote from: Maesus on 28-November-07, 19:33:33
1. It's ICH9 RAID. It's southbridge, not northbridge. It's hardware RAID.
ICH9 provides a RAID facility is software RAID using Intel Matrix Storage Manager. The CPU processes the parity for RAID 5.
Quote from: Maesus on 28-November-07, 19:33:33
2. you can max up the SATA ports. How many is on this board? 6 SATA ports? you can use them all.
There are 2x eSATA ports (I am pressuming from the ICH9), and 4x SATA on the ICH9, and 1x SATA on the 88SE6111. What I was trying to ask is do the 2x eSATA ports render 2 of the ICH9 ports unavailable?
Quote from: Maesus on 28-November-07, 19:33:33
2a. USB ports does NOT reduce the total amount of USB ports to use, where did you get that info or having that impression??
I worded this completely wrong. My bad..... I have had motherboards before where if you connect a usb back plane to the USB header on the main board, it simply stops you using some of the USB's on the rear panel. This is simply like a redirect to allow you to plug USB devices in to the front of your PC case instead of reaching around the back for it rather than allowing you to add additional ports. This is what I was trying to ask, If I am to use the 2x eSATA ports does that mean that it renders 2x of my onboard SATA ports obselete.
Quote from: Maesus on 28-November-07, 19:33:33
3. Yes
Thankyou
Quote from: Maesus on 28-November-07, 19:33:33
4. it's not really compatibility issue, but more of Vista's own issue, just that you need to do the right step to get Vista installed. Quad Core + 4GB, well, microsoft acknowledge the Vista installation issues with this config. You will need Vista 64-bit, but start installing with 1GB or 2GB. After completing installation, install microsoft quad core and 4GB patches, then only plug in the remaining 2GB.
Thankyou

MSI P35 Neo2 - Sleep S3 Problem

Hello.
My System:
CPU: Core2Duo E6850 @ 3.0 Ghz (FSB:1333 | 333 x 4)
RAM: 4 x Kingstone HyperX DDR2 1Gb ram @ 800mhz
M/B: MSI P35 Neo2 Fir
GPU: Gigabyte Radeon HD5770 1024mb
HDD: Western Digital BlackCaviar 640gb 64mb cache
SSD: OCZ Agility 3 60gb
PSU: Fortron BLUESTORM 400w
O.S: Windows 7 (SP1/Without SP) Ultimate / Hackintosh 10.5.8 / 10.6.8 / 10.7.3 / OpenSuse 11.2 / 12.1
Recently i decided to enable the sleep mode on my computer (because the power cost, my computer is all the time on).
So, i go to my bios and i change the suspend mode to S3. I boot my os (windows7) and i tried to sleep.
The system is going to sleep fine but nevers wakeup, the led of motherboard is flashing fast red-green-reg-green and after random time stops flashing, sometimes all are red and sometimes are all green!
Before post here i tried to fix the sleep and i read evert post.
I have try: Flash Bios to (1.8, 1.7, 1.2, 1.C, 1.A, 1.9), update all of my drivers including (lan, gpu, chipset), disconnect every usb includes keyboard (i tried with old ps2 keyboard), disconnect all pci cards, disconnect all RAM's (except one), i tried another Graphics Card (Gigabyte 8600GT), another PSU (Premier 400w), Bios Settings (ACHI/IDE, Recall GPU, PCI express x4, clear cmos), change DVI connector port on gpu, change to analogue RGB D-SUB, reinstall windows to ide disk/sata disk with S3 Enabled!
I tried to sleep from my Hackintosh 10.7 with the same error and with linux (openSuse) with the same error.
I have notice coz when i remove rams and i downclock the cpu and rams the leds are stop flashing in 2-3 secs (normaly tooks 10-40 secs)
Also the mb never wake with keyboard key press event!
Please experts, i need your help...

@NovJoe
Thanks for reply!
I have test with one piece of ram. also i tested with another cpu (Intel Celeron 1.6 - i cant remember the model).
My motherboard version is 1.2 (MS-7345 V1.2)
(i dont know if it helps but hibernation working really good! working on windows and mac)
before a hour i test to reprogram bios with floppy disk! first i destroy my bios (i edited with ami tools to corrupt and the mobo start the recovery process, i put a floppy with the last bios renamed to AMIBOOT.ROM and the recovery worked! but sleep not)
i dont want to talk with msi for a too old mobo, so if anyone knows whats is happen please help.

MSI P35 NEO2 FIR voltage problems!!

Let's start:
I have MSI P35 NEO2 FIR ,e5200,2 x Geil ultra plus 1066+,as us 2900CT,lcpower 6550g and...rest- not so important for my questions.
1.My problem is next: default voltage values for my RAM is ~2.2-2.4 every time I check in windows (speedfun,sisoft Sandra, everest..)shows me 2.0 or some time even 1.8v . When i change voltage in bios and went to win voltage on RAM is still unchanged (2.0v) .
Same thing happen with NB voltage. But CPU voltage I can change freely with no problem.
When I change fsb(try to overclock) suddenly memory voltage rises how i do not now , but only to 2.35 and no more.
Can anyone help me fix this problem because my memory is not stable at 2.0 or 1.8 sometimes and system crashes?
2.When i change cpu settings from 12.5*200 to (example)10*300 in windows even in system properties see that my current clock is 12.5*300=3750 and not 10*300=3000 like it should be .
Is it bios problem?
My bios version is 1.9.
Thanks!

same problem with the Neo2 FR (like mine). After quite of bit of researching and testing i reckon that software can not correctly read the vRAM on these MSI boards. I found that Speedfan, Everest, and HardwareMonitor all gave an incorrect reading for my RAM's voltage. Also, if i increased the cpu voltage in the BIOS then the voltage monitoring programs would show an increase in CPU voltage and RAM voltage (even though i had not changed the latter).

MSI P35 Neo2 Fir Patriot Memory Problems.

Hi,
Having problems with my Patriot Performance PC2-6400 Low Latency Memory DDR2 (800mhz) 4-4-4-12, 2,2v, 2 * (2gb(2*1GB)kit) =4gb total
on a MSI P35 Neo2 Fir moderboard with Intel Q6600 cpu)
When i check the memory with CPU-Zv1.44 the memory only goes with the frequencys of
DRAM Frequenzy 399.5mhz
FSb : Dram 2:3
Cas# latency 5.0 clocks
Ras# to Cas# delay 5 clocks
Ras# Precharge 5 clocks
Cycle Time 16 clocks
Why doesn't they go in 4-4-4-12 frequencys ???
Have tried to manually change dram timing in bios but no success
so i went back to auto dram timing.
What can i do to get the 4-4-4-12 timings.
Please help.
thanks in advance swefin

Quote
When i check the memory with CPU-Zv1.44 the memory only goes with the frequencys of
DRAM Frequenzy 399.5mhz
~400 MHz is the correct frequency for your modules. CPU-Z shows real clock speed. DDR means Double Data Rate (two transactions per clock cycle). Multiply 399.5 MHz by two in your head and you have your effective DDR(2) rating of 800 MHz. There is no problem here.
Quote
Why doesn't they go in 4-4-4-12 frequencys Huh
Have tried to manually change dram timing in bios but no success
so i went back to auto dram timing.
What can i do to get the 4-4-4-12 timings.
CL5 is the standard latency for DDR2-800 modules. It ensures that they are able to operate @JEDEC standard voltage settings @1.8V (+/-0.1V). The board is supposed to set memory timings to CL5, otherwise your system would not be able to boot at standard voltage. Check the "SPD" tab in CPU-Z and look for the standard timings that were programmed into the SPD chips of your modules (400 MHz), I am absolutely sure that you won't see 4-4-4-12 @400 MHz @1.8V being part of the SPD tables.
You have to manually adjust memory timings in BIOS to 4-4-4-12 AND also increase memory voltage to the value the manufacturer recommends for CL4/DDR2-800 MHz. The voltage is usually 2.0-2.2V depending on the brand and type of RAM in use.

Need Help with ESATA on MSI P35 Neo2-FR

Similar Messages

Maybe you are looking for