Need help with new SoundBlaster ROAR SR20 or it goes to the trash. [Bluetooth]

Hey Guys, I just recently purchased a the Sound Blaster ROAR SR20 and even after 2 days of owning it and countless searches for help, I've come to no conclusion of why i cant get my laptop to recognize it [Bluetooth] and allow me to download any drivers for it. I have tried Connecting it VIA USB 3.0 whereas the drivers said they were successfully installed [and it works over USB] but when i attempt to re-connect via Bluetooth it shows that 3 separate Bluetooth Peripheral Device Drivers are needed and not installed. I am currently running Windows 7 (64x) Professional and have tried already using this method but with no luck.
http://support.microsoft.com/kb/2654568
Attached [hopefully] is a image/screenshot file of the drivers it is showing errors for.
http://i.imgur.com/6xn9NjV.png
Hope to hear back from you all soon,
Will Champion

Originally Posted by Colin-CL
Hi Will,
Please confirm that your laptop supports the following Bluetooth profiles:
Supported Bluetooth Profile
- A2DP (Wireless Stereo Bluetooth),
- AVRCP (Bluetooth Remote Control),
- HFP (Hands-Free profile)
If you have access to another Bluetooth speaker, you can try to connect it to see if you are still facing the same issue. What we like to do here is to narrow down where the potential cause of the issue is.
Another option is to use this bluetooth transmitter with your laptop. Let me know how it goes and I can make further suggestions based on the outcome.
Cheers,
Colin-CL
Ok so i purchased a aptX enabled dongle, installed the drivers from a mini CD, and now when i connect using the CSR 4.0 Bluetooth driver that now shows up on my taskbar, a pop up displays saying that Im now connected to an aptX enabled device.
Now my problem is that under properties (when selected for playback) i notice that now my advanced settings are drastically...well...crappier. Meaning that the Default Format sampling rate is Locked at 1 Channel, 16 bit, 8000Hz which is telephone quality, and it sounds like telephone quality.
However when connect using my built in Bluetooth adapter my Default Format sampling rate is 2 Channel, 16 bit, 44100Hz which is CD quality and i have the option only one other selection....2 Channel, 16 bit, 48000Hz which is DVD quality.
One would think that the so called legendary aptX codec would allow for a higher sample rate so I am wondering if this is user error or perhaps i have an outdated driver (a problem since CSR updates/drivers are no where to be found on the internet)
Im Hoping that maybe you can help me resolve this issue since Ive hopefully narrow down the list of possible errors
Hope to hear back from someone soon
Thanks,
-Will Champion
USB Info: Supertech USB Bluetooth 4.0 Low Energy Micro Adapter with CSR8510 controller and CSR Harmony
http://www.amazon.com/gp/product/B00HQE4MRU/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

Similar Messages

I need help with event structure. I am trying to feed the index of the array, the index can vary from 0 to 7. Based on the logic ouput of a comparison, the index buffer should increment ?

I need help with event structure.
I am trying to feed the index of the array, the index number can vary from 0 to 7.
Based on the logic ouput of a comparison, the index buffer should increment
or decrement every time the output of comparsion changes(event change). I guess I need to use event structure?
(My event code doesn't execute when there is an event at its input /comparator changes its boolean state.
Anyone coded on similar lines? Any ideas appreciated.
Thanks in advance!

You don't need an Event Structure, a simple State Machine would be more appropriate.
There are many examples of State Machines within this forum.
RayR

Need help with new itouch

Please bare with me, while I 'try' to explain.
I have my itunes account linked to my iphone and macbook. I have bought my daughter an itouch for Xmas. Now I have set up a seperate itunes account for her on my other Windows laptop. So she is able to purchase apps without them going and clogging up my itunes... NOW this is the bit i need help with...
How can i transfer any music i have on my itunes to her itunes? and vice versa?
Thanks in advance

Right, I have now gone down the line of setting up a new user on my macbook, her own ID and then with the help of Mr google, I followed the steps of sharing my music, by moving my itunes media folder to a shared folder.
Now i got my music on her itunes libary but when i did a test download of an app, it wont show in the library. I have even done the 'transfer purchases'. and its still not showing. I am slowing loosing the will to live with it! I really need help.

Need help with new 8310

Just upgraded from earlier blackberry and have two problems I need help with!
First, in rearranging the icons my browser icon disappeared and I can't get it back even when I use the show all function. Any ideas?
Second, unlike my earlier blackberry, messages I sent from my office laptop are not appearing in my messages. What setting do I need to tweak? I like my blackberry to show all the messages sent from or received by the laptop.
Thanks.
Lauren

My BB setting was to not hide sent messages, but the problem I think has to do with the settings on syncing with my computer. Messages I send from the blackberry show up as sent - but I want the BB to match completely with the email on my computer - show every email received and every email sent. That was how the old BB was set up. Any ideas on what else to tweak either on the desktop or the BB? Thanks for your help.

My need help with my iphone. i got up yesterday morning and the phone was completely off. Also, is not charging problem because it was charge before that happen.c

I need help with my iphone. For some reason is off completely and refusing to come on. I believe is not charging problem, because it was charge before that happen.

You have posted under MacBook Pro.
I have asked the administrators to relocate this post to the iPhone section where it is more likely to get a helpful response.

Need help with iMac intel desktop - Mac mail consistently going OFFLINE

I need help with Mac mail - it is frequently going "offline" and requesting me to "take all accounts online". My internet is working. It's been checked, checked and checked. Sometimes it just takes a reboot of the system and the modem to kick it in and make the little triangle symbol go away, but should I have to reboot daily? I have the Mac OS X Lion 10.7.5 installed. Is there a bug here or am I supposed to upgrade to Mavericks? Any help is most appreciated.

For me this is an issue caused by my email service provider. When they are slow to respond or to accept the password Mail takes that as a password rejection, and prompts me to reenter password, and eventually goes offline.

Hard drive crash need help with new iTunes load and backup files

I have looked through the posts and not found my situation.
I had my iPhone synced to a PC computer and the hard drive crashed. I had an extensive library in iTunes, but none of the music was purchased online so I can't simply download it again. It was all from CD's, many of which belonged to friends. I now have an iMac. The music I like is still on my iPhone, but not on my new iMac. When I try to sync the iPhone with my iMac it wants to delete all the music on my iPhone. Is there any way to copy the music off my iPhone first - so I can add it back into my iTunes library?

Yes, luckily I have been in this situation.
You can download a free application that will take your music from your iPhone and place it onto your Macintosh HD.
One of these should suit your needs:
http://www.macupdate.com/app/mac/19890/ipoddisk
http://www.wideanglesoftware.com/touchcopy/index.php?gclid=CPjvvOiyr6gCFaNl7Aodm h6QIQ
http://www.headlightsoft.com/detune/
I hope this helped.

Need help with new url address

i'm very new to iweb and .mac - i've worked with websites before but never actually registered for a domain and need help setting up my iweb or .mac website with a new address.
Can someone please help me with this...prices? where do i go? i just don't want to create a site for our student ministry at church without having a web/myname.com address.
Thanks in advance!
Chris

You'll find there are a lot of good ones. Godaddy is one that I used to use. I am very happy with bluehost.com great prices and excellent service
Produce | Shoot | Edit
Take Two Visual Media
http://www.take2vm.com

Need Help With New Build, Please

Ok, built a new PC. Here are the parts:
MSI K8N Neo4 Platinum
XFX Geforce 6800GT
Seagate 160 Gig w/ NCQ
1 Gig (512x2) Corsair value memory 3200
PC Power and Cooling 470 Watt Silencer w/ Y PCI-express adapter
Athlon 3500+ (Clawhammer, says Newegg)
Lian-Li V-1100 (black)
My problem: 99.7% sure all cables are connected properly.
All lights and fans come on, drives open and close, but no video signal.
D-Bracket indicates the boot sequence is stuck on "processor initialization".
Things I've tried:
Swapped out the motherboard for an Asus A8N-SLI, same problem.
Reset CMOS on both: same problem, obviously not a motherboard issue.
Built w/ just CPU, GPU, and Memory on a towel, not a grounding issue.
Tried swapping out DIMMS one at a time in primary slot, same problem with both.
Yes, both 24-pin connectors and 12v 4-pin connector are hooked up.
Where I am now:
It's not the motherboard, or memory (unless both DIMMS are bad).
Based on the D-bracket LEDs, I assume it was the processor. I've sent the processor back to Newegg for a new one.
If that's not it, that leaves the PSU, the GPU, and/or the way I've got the y-adapter running to the GPU via two molex.
If the processor comes back and it doesn't work, I'll probably buy a cheap PCI card from newegg to see if it's a GPU problem. And/or I'll try a new PSU with a native 6-pin PCI-Express power connector.
Does anyone see any common compatibility problems with the K8N Neo4 Platinum and the parts I've selected, and/or does anyone have any other suggestions?
It's very depressing to have all this gear sitting around and be unable to power up Half-Life 2. :( Any help would be appreciated.

Quote from: tdho on 19-April-05, 05:06:22
Most likely RAM is your problem. Reset bios and try new memory.
Tom
Possible, but as mentioned, the LED bracket indicates it makes it completely through POST without the video-card, and I've tried alternating each DIMM, one at a time, in the primary slot. Unless both sticks are bad (wonder what the statistical chance of that is), it's not memory.
Though I'll try swapping out both as a last resort if the GPU switch doesn't work.

Need help with new Time Capsule/Airport express setup!

I just hooked up a 500g time capsule to replace an airport extreme, and now my airport utility on my MacbookPro Retina no longer recognizes the airport expresses I had on my network for airplay purposes. Can anyone help with this issue?

Instead of a switch you need a wireless router, because your modem will only assign one public ip address to the switch and that ip address will be forwarded to any one computer at a given time...You should replace the switch with a wireless router and it should resolve your concern...

I need help with Apple iCloud verification. I don't have the email and I can't figure out how to get Apple to send me a new one.

So, in order to back up my music and stuff to the cloud I need to verify my Apple ID and I don't have the verification e-mail. If someone out there could help me out by telling me how to get Apple to send another one, or if they can, I would appreciate it alot. Thank you!!!!!

Apple ID: Associating and verifying email addresses with your Apple ID

Need help with New Topic in RoboHelp 7

I'm trying to pick up where someone else left off and am a little lost. I have a WebHelp project on a Sharepoint site. I have added a new topic which I can see in my file structure, but when I generate the project the new topic file does not show up. It must be something small I'm missing. Help!!

Welcome to our community
Did you add the topic to the Table of Contents structure or the Index? How are your users going to arrive at the topic?
Cheers... Rick
Helpful and Handy Links
RoboHelp Wish Form/Bug Reporting Form
Begin learning RoboHelp HTML 7, 8 or 9 within the day!
Adobe Certified RoboHelp HTML Training
SorcerStone Blog
RoboHelp eBooks

Need Help with new site glitches PLEASE!!!

I need help trouble shooting a website. The site is
www.farrowandwatkins.com. Nav buttons on Mac they display correctly
which is aligned at top and bottom of content to left on Home page.
However, when viewed on PC, the buttons spread to fill the
distance of the "Patients" Page. All the pages spread to this
length also, but are not suppose to.
Nav buttons have padding of 10 on bottom, except last one.
Please help if you can

First guess would be that there doesn't seem to be a fixed
height or width on the cell for the 'patients' button.

Need help with creating template. Changes are not going through to index.html page

Hi all,
I have an issue with my template that I am creating and also a question about creating template Regions (Repeating and Editable).
Somehow my changes to my index.dwt are not changing my index.html page.
Also my other question is: For my top navigation bar and left navigation bar links, do I need to select and define each individual button or link as Repeating/Editable Region? or can I just select the whole navigation bar (the one on the top) etc...
Below are my steps for creating my template...I am kinda fairly new to using DW and this is my first attempt to making a template following the DW tutorial CD that came with DW CS3.
I appreciate any help with this...regards, Dano
-Open my index.html file
-File/save as template
-Save
-update links - yes
-Select Repeating and Editable Regions (I selected the whole top navigation bar and selected Repeating Region and Editable Region, same with the left side navigation links)
-File close all
-Open the index.dwt
-Save as and selected the index.html and chose to overide it..
When I make changes to my index.dwt it is not changing the index.html
I feel that I am missing some important steps here.....
Website address
www.defenseproshop.com

Figured out

Need help with a basic script to resize image then resize the canvas

I am new to photoshop scripting, and have come across a need to force an image to be 8"x10" at 300dpi (whether it is vertical or horizontal)
I need to maintain the correct orientation in the file, so an Action will not work, I believe I have to implement a script to accomplish this.
I have the below script so far, but I am not certain of how to input the variables / paramters
doc = app.activeDocument;
if (doc.height > doc.width) doc.resizeImage("2400 pixels","3600 pixels", "300", "BICUBIC");
if (doc.height > doc.width) doc.resizeCanvas("2400 pixels","3000 pixels", "MIDDLECENTER");
if (doc.height < doc.width) doc.resizeImage("3600 pixels","2400 pixels",300,"BICUBIC");
if (doc.height < doc.width) doc.resizeCanvas(3000,2400,"MIDDLECENTER");
When I run this script, I get the following error:
Error 1245: Illegal argument - argument 4
- Enumerated value expected
Line: 5
if (doc.height < doc.width) doc.resizeImage("3600 pixels","2400 pixels",300,"BICUBIC");
The fact that its failing on lien 5 lets nme know that I have the "If" portions of my script correct, I just dont know how to accomplish the functions correctly.
Any help would be appreciated!
Thanks,
Brian

I know I'm late here but it seems to me your trying to automate a 8"x10 or 10"x8 300DPI print.
To do that you must first crop your image to a 4:5 aspect ratio to prevent distortion unless your shooting with a 4" by 5" camera. I wrote a Plugin script a couple years ago that could help you do a centered crop. You could do the whole process by recording a simple Photoshop action that uses two Plugin Scripts only four steps would be needed.
Step 1 Menu File>Automate>AspectRatioSelection (My script based of Adobe Fit Image Plugin script) Set 4:5 Aspect ratio, center, Rectangle, Replace, no feather. Llike Fit Image this script woks on both Landscape and Portrait images. The Selection will be correct for the images orientation.
Step 2 Menu Image>Crop
Step 3 Menu File>Automate>Fit Image set 3000 PX height and 3000 PX width the Image will be Resample so its longest side will be 3000 pixels. Adobe Fit Image Plugin Script always uses BICUBIC resampling. I have a modified version of Fit Image that uses Bicubic Sharper whebndownsizing and BicubicSmoother when up sizing.
Step 4 Menu Image>Size un check resample set resolution to 300 DPI.
When you play the actions the Script Dialogs will not be displayed and the setting use when you recorded the action will ne used.
The Plugin Script are included in my crafting actions package:
http://www.mouseprints.net/old/dpr/JJMacksCraftingActions.zip
Contains:
Action Actions Palette Tips.txt
Action Creation Guidelines.txt
Action Dealing with Image Size.txt
Action Enhanced via Scripted Photoshop Functions.txt
CraftedActions.atn Sample Action set includes an example Watermarking action
Sample Actions.txt Photoshop CraftedActions set saved as a text file. This file has some additional comments I inserted describing how the actions work.
12 Scripts for actions
My other free Photoshop downloads cam be found here: http://www.mouseprints.net/Photoshop.html

Need help with new SoundBlaster ROAR SR20 or it goes to the trash. [Bluetooth]

Similar Messages

Maybe you are looking for