Need help with new Time Capsule/Airport express setup!

I just hooked up a 500g time capsule to replace an airport extreme, and now my airport utility on my MacbookPro Retina no longer recognizes the airport expresses I had on my network for airplay purposes. Can anyone help with this issue?

Instead of a switch you need a wireless router, because your modem will only assign one public ip address to the switch and that ip address will be forwarded to any one computer at a given time...You should replace the switch with a wireless router and it should resolve your concern...

Similar Messages

Bt Home Hub (fibre optic) can it work with my Time Capsule & Airport Express?

I have just moved house after having no problems for years with my virgin cable I have now had to switch to Bt because cable is not available at my new address therefore I would like first and foremost to have my Time Capsule available to use as a hard drive, I am not too bothered about wi-fi as that comes from the bt hub, only thing is I am at a loss how the Time Capsule hard drive is not working. Also is there anyway the Bt Hub can connect/link to Time Capsule or even Airport Express.

Your TC can be used bridged to the BTHub.. and plugged in by Ethernet.
It is best to still use the TC wireless for the express to extend and you will find access easier.
Always best to start with a factory reset when you do this.. The TC remembers too much from its last configuration.

Need Help with 5 Port Switch, Airport Express, and wired iMac

I recently purchased an airport express to accomodate my laptop's wireless capabilities. However, the airport express has only one ethernet port, as does my parents' modem. Thus, I could either hook up the airport or my parent's iMac. I chose the airport, which resulted in a few weeks worth of fights. To alleviate the problem, I purchased a linksys 5 port group switch, after someone told me I could use that to hook up both at the same time. Initially, the iMac wouldn't work. It registered what I was told was an invalid IP address. Then a cable technician came by, reset the modem (unplugged the battery), and now the airport does not work; it flashes yellow and says that it cannot detect the ethernet signal.
The iMac is running OSX 10.3 and the laptop OSX 10.4. I am not sure if the modem can only accomodate one IP address or if there is any way to share IP addresses. Do I need to change something with the DHCP on my laptop? Do I need to manually enter an IP? Any help would be greatly appreciated. I'm completely lost....and without wireless internet.

Instead of a switch you need a wireless router, because your modem will only assign one public ip address to the switch and that ip address will be forwarded to any one computer at a given time...You should replace the switch with a wireless router and it should resolve your concern...

I need help with this Time Capsule and External HD problem!

my time capsule is working perfectly and i decided to hook up a seagate 500 external hd thru the usb on the back of the time capsule!
well i can see both drives on my macbook and i can transfer files from my mac to both hd with a breeze
one major problem i cannot extract files from my external hd only put files in! i tried checking the setting and everything but with no avail! anyone have this problem and how did they fix it? thank you!
Message was edited by: aphextwin007

Try connecting another USB storage device to the TC - HDD or memory stick. Format the device while it's connected to the TC, then try writing and reading to it.
It does seem very odd that you can write to the HDD but not read from it. Presumably when you copy files to it they appear in Finder - you can see them OK? Do they appear to be the right size ("get info", or click in "columns" view). What exactly happens if you try to drag them back to the desktop?
I can only think that you may have a hardware or formatting problem, hence trying a different, freshly formatted, drive.

Need Help With Best Configurations for Airport Express

I have to macs and an ipod touch that are usually connected to the same wifi. when I am watching a youtube video or downloading something the connection gets really slow on the other machines.
For example:
i am downloading a movie from the itunes store and i am trying to watch a youtube video on the other computer or checking my email on my iPod, the connection is really slow.
Is this because of the internet connection (3mbs)? or the express??
So i want to know if there are any settings aside from the factory settings to make it faster.
BTW: there are usually 4-5 other wifi's near me.
and the macs are less than 15 ft away from the airpost express..
thanks for any help!!!

The issue is the speed of your Internet connection.
You are doing very heavy downloads and therefore your limited 3mpbs capacity is not enough to meet the demand.
The Airport Express can provide much higher throughput that your internet connection so the problem is not there.

Best configuration to extend wifi with Time Capsule & Airport Express

In my house I have a Fritzbox wifi router on the ground floor as my primary internet access. I have an ethernet cable going to the 3rd floor study where the Fritzbox signal is relatively weak. I purchased a Time Capsule as a backup device, but also wanted to extend the Fritzbox wifi network by plugging the ethernet cable in to the TC. I was not successful in extending the network, so I had to create a new network. When moving from downstairs to upstairs, my iphone keeps the connection to the (now weak) wifi network and I have to manually change to the (stronger) TC wifi network.
Additionally, I used to be able to successfully extend the downstairs wifi using my Airport Express (and also managed to have my speakers plugged into this for wireless usage), but do not want to additionally complicate my set-up.
So, what is the best way to connect the following equipment, ideally with the same network name, to ensure I always use the strongrst signal automatically:
Third floor:          iMac,    Macbook,   Time Capsule, Airport Express
          Ethernet cable from ground floor to 3rd floor
Ground floor:     Fritzbox wifi connected to internet

You must configure the Bridge Mode setting as the very last step before you Update the settings, otherwise the setting will change automatically.
In other words, you can change the setting to Bridge Mode, but if you make any other changes before you click Update, the Bridge Mode setting will not take effect.
Or, if you see any error messages about DHCP conflicts or Double NAT....the AirPort is not in Bridge Mode...even though you might think it is. Check the settings again.
will I still be able to set up an additional 5GHz network in parallel?
Yes

Hi I've recenty purchased a new imac time capsule airport express. I've set up a new network, rather than extended the current one. How do I change my new network to an extended one or create an extended network?

Hi I've recenty purchased a new imac + time capsule + airport express.
I've set up a new network, rather than extended the current one. How do I change my new network to an extended one or create an extended network?
Michael

detailed in terms of what focus?
here is a video guide about using the airport utility
http://www.youtube.com/watch?v=65Jv6m43eIE

Time Capsule-AirPort Express-WDS not working together

According to everything I've read here, I've configured this properly, but it doesn't seem to be working. If anyone can help me troubleshoot this I would greatly appreciate it.
I have a new Time Capsule acting as my main wireless base station; it has a manually-configured static IP address, is plugged into my Verizon FIOS router, and is set to distribute IP addresses over wireless using DHCP. I have it set to run a 5 GHz network in addition to the regular 2.4 GHz network. I have an older AirPort Express that I want to use to extend the range of the 2.4 GHz network (the Express can only do 802.11b/g, not 802.11n), in part because we have some older devices in the house that I don't want to slow down the 802.11n network, and in part because the 802.11b/g signal doesn't reach all parts of the house very strongly. So I told the Time Capsule to make its network extendable, told the AirPort Express to participate in a WDS network as a WDS relay, and entered the MAC address of the Time Capsule's 2.4GHz network as the WDS main. Result: flashing amber light on the AirPort Express, which no longer shows up in the AirPort Utility; I had to do a hard reset in order to get the Express back (and then it had to be reconfigured again, of course). At the moment I have it just joining my wireless network, and that works -- green light -- but of course doesn't allow the Express to extend the range of the wireless network.
What am I doing wrong here?

Before there was dual band, we always told users that if they used WDS, the entire network would revert to "g", even if the Time Capsule, AirPort Express, etc were capable of "n" performance.
Your findings seem to confirm that this happens with a dual band as well.
I think it's well worth it to get the AirPort Express 802.11n. Then you can reconfigure the Time Capsule back to "Create a wireless network" and check the box to "Allow this network to be extended"
The Express"n" would then be configured to "Extend a wireless network". I use this setup and would highly recommend it. There may be a slight bandwidth loss due to overhead, but the performance is light years ahead of WDS.
If you are using the same network name for both bands on the Time Capsule, then I believe by default the Express will extend the 2.4 GHz "n", "g" and "b" band. This makes sense for most users since 5 GHz signals do not travel well over distance or penetrate obstructions well.
IF...you want to extend the 5 GHz band, the only way that I know how to do this is click Wireless Network Options on the wireless setup page for the Time Capsule and enable the option to assign a different name for the 5 GHz network.
Then you will have to configure the Express to extend this specific 5 GHz network. I never had much luck extending 5 GHz, and I wanted my iPhone to be able to use the network across the house, so I went with the simpler one network name for both bands and extended the 2.4 GHz network.
If you have a "g" device joining the extended network, it may tend to slow the "n" devices down slightly...when the "g" device is active, but it won't drag everything down to "g" levels. When the "g" device is not active, "n" devices will run at "n" speeds.
BTW, the ethernet port on the AirPort Express is active when you configure it to "extend a wireless network". This can come in handy for hooking up DVD players, etc that need an internet connection for firmware updates and extra features.
Follow up....I tried a very quick reconfiguration of my dual band AirPort Extreme (same router that the Time Capsule users) and AirPort Express using the WDS arrangement and everything did indeed drop way down in speed and performance.
Post back if you have questions. Happy to help.
Message was edited by: Bob Timmons

Anyone with a working TC - Airport Express setup out there?

Anyone with a working TC - Airport Express setup (wireless) out there?
My setup is super slow and has dropouts all the time!

I have an AEBS connected to my cable modem, TC connected wirelessly to the network. TC dropps the connection all the time (what a pain!). I also have 2 x 500Gb USB drives connected to the Tc via a USB hub. The interesting thing is if I have mounted both USB drives while the Tc connection is working, I don't los connection to the USBs, just the TC hard drive (TM won't backup because it can't see the TC hard drive). BTW, speed is definitely not an issue and I have "interference robustness" active as I have a cordless 2.4GHz phone.
Still working to troubleshoot and will keep you posted!

Setting up Air play with new time capsule and newer airport express?

I just recently purchased a new time capsule, and I'd like to use my current generation airport express to stream music from my apple devices. I just was wondering what I had to do in airport utility to set this up? I was also wondering how to transition the network over from the old express to the new time capsule as far software settings go. I really appreciate the help and assistance. Thanks folks. I'm really looking forward to setting up the network for our new iMac.

Your setup is very easy..
This is how I would do it.
Remove the express from the network.. ie just unplug it but do not change anything in it. Keep the configuration as is until the TC is working.
Power off the cable modem.. this is requirement.. at least 20min is usually needed, dependining on your ISP.
Go into the airport utility and setup the TC as router for your network .. it is a simple setup.. but I would do as stated.. all short names, no spaces pure alphanumeric rather than accept Apple's names. That is for TC and wireless.
After 20min power up the cable modem. Once it is running and you have internet access. you can proceed to setup the express to do the airplay. If the internet still doesn't work, power off the cable modem overnight..
Do not lose that express setup so if you absolutely have to, you can at any time substitute it back and have internet again.
So everything is working properly TC in place as full router.. now hard reset the express.. and simply use the airport utility to put it in extend wireless .. or plug in by ethernet if you are going to hard wire it.
The extend wireless setup is all done straight from the existing setup.
Now you can plug your express audio port into your speaker.. and setup the airplay via the itunes.
I will get Bob to give you his way of doing it.. There is no one RIGHT way .. but he can give you more info if you want a particular method.

WiFi no longer working with new Time Capsule-can you help please?

Hi all,
Just received my new Time Capsule (TC). It was a little problematic setting up, but probably due to my now choosing to increase my security from WEP to WPA as the TC set-up assistant suggests. Since then, I have had numerous problems getting my other computers and now my iPhone to connect with WiFi.
The problem is that despite entering all the new settings and WPA passwords for my connection with the TC, the iPhone will either momentarily recognize and go to wifi or simply stay on Edge.
On the former, with wifi active, as soon as I go to iTunes, Safari or check email, it reverts to Edge. On the latter, despite resetting, entering password, or tapping Settings and selecting my wifi connection, it will NOT connect and stays on Edge.
(Now, I'm on Edge! I'm bummed that with new hardware I have new problems that didn't exist before!)
Can someone who had this same problem tell me how they resolved it.
Here's the one clue I have, but would rather not resort to: When I first set up the TC, I had it on WEP with a WDS Network, and everything was working great and FAST! Now that I have increased the security—I will be backing up 3 computers to the TC—my iPhone and other computers seem to have intermittent or no wifi connection as a result.)

Irving Gonzales,
If your computers are 802.11N capable, you might want to try an advanced setup that might help your Time Machine speeds some. I have not personally tested it, so it is just a personal theory at this point.
First, in a mixed environment the 802.11N clients all get slowed down.
First, configure the TC for 802.11N only.
Second, connect the Airport Express via ethernet to the Time Capsule
Third, configure the Airport Express for bridged mode (doesn't give out IP addresses), and for its own wireless network with a different name than the Time Capsule.
Have any 802.11b/g clients like the iPhone join the Airport Express' network.
Thank you,
Nathan C.

Older airport extreme base station as a network extender with new time capsule

I just bought a new time capsule (802.11ac). Can my older airport extreme base station (model A1143) be used as a network extender with it?

Yes, although it maybe disappointing..
There are two kinds of extending.. wireless repeater type which is poorest as it has to transfer all packets in two steps instead of one.. hence will halve the speed.
Or using ethernet to the old extreme and set it in bridge.. You can then setup roaming network... this is much better.. but getting ethernet to the right place could be messy or expensive or both.
http://support.apple.com/kb/HT4260
wireless extend doco.. mind all of this is out of date.. the basics are correct.. the methods via the airport utility may be obsolete.
http://support.apple.com/kb/HT4145
Documentation has rather lagged lately.

I need to reset my time capsule/airport every day - time capsule has green light but I don't see any wifi signal on my mac and other computers.

as many of you do, I use time capsule as airport, too...
It worked fine for 6 months or so after I bought the new time capsule. (I bought it in September 2012.)
Since the beginning of this year, I had to reset, and power off and plug it in almost every week, then now I need to reset and power off and back on again every day...
When I first set up the time capsule, I followed the instruction with the manual.
But, now I am so lost and don't want to reset every day for wifi connection.
Anyone has problem like me or knows how to solve this issue?
Please help..
I have MacBook Pro OS X 10.8.4 & my roommates have PCs. (just in case if it helps...)

For PC it is important the wireless has names that are compatible.. short.. like 10 characters.. but 2-20 is fine. no spaces.. and pure alphanumeric.
Use WPA2 personal only.. with pure alphanumeric password .. again 10-20 characters should be fine.
The latest firmware is a dud. Go back to 7.6.1
Open the airport utility.. click on the TC and holding the option key click the actual version number..
Go back to 7.6.1 is simple.. just select it and away it will go.. ignore future requests for upgrade.. you can also tell the utility not to check weekly for updates. You will need 5.6 utility for this I think..
So do the firmware downgrade.
Then do a factory reset and follow the name information above.. for TC name as well btw.. wireless name/s and disk share name.. which by default is data and that is fine.
So some instructions in...
The Factory Reset.
Power down the TC.
Hold in reset. and keep holding it in. Be Gentle! It is a tiny surface mount switch with a plastic lever.. Attempting to push it out the other side of the TC will not make the switch turn on better.
(I fix TC and have several reset levers bent over and jammed or broken off).
Power on the TC.. remember with the reset held in.. this needs three arms.. a friend or power switch you can get to with your feet..
Keep holding in reset for about 10sec until the front LED flashes rapidly.
Release reset and wait .. the boot will be slow as it deletes previous setting.. only from router side and pulls out the factory defaults. No files are deleted on the hard disk.. but the name of the TC may change.
How to load 5.6 into ML.
1. Download 5.6 for Lion.
http://support.apple.com/kb/DL1482
Click to open the dmg but do not attempt to install the pkg.. it won't work anyway.
Leave the package open on the desktop so you can see the file. AirportUtility56.pkg
2. Download and install unpkg.
http://www.timdoug.com/unpkg/
Run unpkg on the desktop.. If your Mac refuses to run the software, because it wasn’t downloaded from the Apple store, go to security in preferences and allow other software to work.. this is limitation of trade methinks. You can set back later if you like.
Now drag the AirPortUtility56.pkg file over to unpkg.. and it will create a new directory of the same name on the desktop.. in finder, open the new directory, drill down.. applications, utilities .. there lo and behold is Airport utility 5.6 .. drag it to your main utilities directory or just run it from current location.
You cannot uninstall version 6 (now 6.3 if you updated) so don't try.. and you cannot or should not run them both at the same time.. although I have had no problems when doing so.
You can also load airport utility into a pc and get access to all the settings. Untick the box for firmware updates.. it will still bug you occasionally.. regardless of the setting.. just ignore it..
You might still need to do the occasional reboot of the TC as well.

A Time Capsule, Airport Express and AT&T 2Wire walk into a bar...

Alas, I'm sure this question has been asked before, but my reserach keeps turning up separate answers. So I thought I'd turn to this forum for some advice. Ultimately I'm seeks suggestions on various ways to configure my network to allow easy backups, connection two rooms, and wirelessly print from anywhere.
I have a:
Time Capsule (dual band) - used for Time Machine backups
Airport Express (older)
and new 2Wire 3800HGV-B wireless modem/router from AT&T (for U-verse internet/TV)
My room configuration is:
Living room with TV, internet connected DVD player, and new AT&T 2Wire Wireless U-verse modem
Home office with 2 desktop comptuers (no wireless cards) and a USB printer.
Two roaming laptops which move around the rest of the house
The livingroom and the office can't be connected with a physical wire.
What I was hoping to do was setup my office with the Time Capsule in the office as a wired hub, and then use it as a wirelessly bridge to the 2Wire network. But as I understand it, a Time Capsule can't be used as a bridge to a non-Apple product. Please correct me if I'm wrong.
Alternately I could always get wireless cards for the desktop computers, but this leaves the printer.
I've read suggesitons of people who have used their TC as the primary router, disabling wireless on their AT&T 2Wire, and hooking the two together with ethernet. Others who just join the TC to the 2Wireness network. But really what I'm seeking is a way to join the two rooms.
Any thoughts? Am I asking the right questions or providing the right information?
Much thanks,
dana.

So I figured I'd go with an initial suggestion and attached my TC via ethernet to the 2Wire modem/router in my living room, and make the TC my primary wireless router.
Good plan
since both will be in the same room, I assume I need to disable wireless on the 2Wire
Correct
What kind of configuration do I need to do on the TC, or do I just following the wizard and select 'Extend existing network'?
You can follow the guided setup or I can give you a step by step manual setup. In either case, you will configure the TC to "Create a wireless network".
("Extend" is only used if the TC connects using wireless only....you will be using Ethernet from one of the LAN <-> ports on the 2-Wire to the WAN port (world icon) on the TC.
The guided setup will normally sense that the TC is connected to another router and suggest that the TC be configured in Bridge Mode, which is the correct setting. Otherwise, select the Bridge Mode option when it is presented.
Note....If you have a newer dual band TC, the Guest Network option cannot be enabled when the TC is configured in Bridge Mode. So, if you want a "Guest" network, maybe the 2-Wire could provide that service.
Should I attach this (via ethernet) to the TC or the 2Wire?
Pick a LAN <-> port on either one, your choice, whichever is easier
What should the AT&T DVR be connected to?
I'm not familiar with an AT&T DVR, but if it connects via Ethernet, you can connect to a LAN <-> port on either the 2-Wire or the TC
For printing, my plan is to attach the printer through USB to the Airport Express and then connect that wirelessly to the TC network (though my first attempt at this failed to connect).
Suggest that you get the TC up and working smoothly. Then tackle the Express.

Need Help on a Time Capsule setup

I want to install a new 2TB Airport Time Capsule to replace my older Time Capsule. I would like to continue to use my original Airport Extreme for my network and have the new Airport Time Capsule serve as an extension of that network. I have referred to the following article http://support.apple.com/kb/ht5096 but then started having issues of understanding what needs to be done.
While there is obviously wireless capabilities for the new Time Capsule, I was thinking that to initially copy the old Time Machine to the new that I would use an ethernet cable. (The old Time Machine is USB to an external drive). Once the copy is made I'd like to remove the ethernet and position the new time machine for wireless connectivity. I'm not sure how to connect everything together. My modem is connected to my iMac 27 by ethernet (that's faster, right?) and so I don't have any ethernet ports available on the modem. (one is input, one is output to the airport extreme, and one is output to my computer.)
How do I connect things for the initial copy and then for the wireless in the future? The set up book talks about Connecting Ethernet cable connected to the cable modem to the Ethernet WAN port. Then it talks about Ethernet cable from any Ethernet device to any of the Ethernet LAN ports. I don't understand any of that - what I have or what I want. Is there any connection from the 2TB to the iMac?
Then a window pops up about the 2TB and asks for a password. What's that? Then it asks what is primary (well, I thought I wanted the older Airport Extreme to be dominant and the 2TB to connect as an extender. I don't see that option.)
Anyway, confused about connectivity. In the end, I'd like to copy the old Time Machine to the new Time Machine and I think the above article will get me there. But I'm troubled about what wires go where. Any suggestions?

Time Machine is the backup software on your computer.. it has no relationship to any particular hardware.
Time Capsule is an apple router with a hard disk inside. It is not related in any way to Time Machine.. !!
BUT it is used mostly as the target for a Time Machine backup.. Apple naming is very messy.
1. It's the small white device that gives me a wireless service in my house. It has no drive just serves to provide wireless.
It could be an extreme or express but you state later on it is extreme.
I was thinking to use the time capsule as my Time Machine drive but use the wireless capability as a network extender of the original AirPort Extreme.
Generally it would be better to use the TC plugged into the main ISP modem / router. And you can then use the Extreme to extend the network.. it does depend on locations.. you want the least number of wireless hops or the best chance of running ethernet to the clients. Either setup will work but think which is fastest. Whenever a backup has to go.. computer--extreme--TC. with both connections by wireless it will go at half the speed of
computer--TC.
And if you can plug the computer--TC by ethernet it will go about 3-6 times the speed of wireless.
2. I was wondering what is the best way to get the old Time Machine data onto the new 2TB Time Capsule to be used as a Time Machine.
I recommend you start over with a fresh clean backup. The issue is the local backup and the network backup are handled differently by Time Machine and it is not easy to do what you want.
See Q18 here if you want to see what is involved.
http://pondini.org/TM/FAQ.html
Specifically this one. http://pondini.org/TM/18.html#id18
3. Yes.. but think if it isn't better to move the extreme instead.
4) my modem connects via Ethernet to my desktop because I thought wired was faster than wireless. My modem also connects to the AirPort Extreme to broadcast a wireless network for my iPhone and iPad. I could have my desktop connect wirelessly but just thought wired was faster. OK I see what you say about plugging the desktop in to the wireless router instead.
This is wrong.. You should have the computer plugged into the airport router.. and the airport router plugged into the modem.. not both connected to the modem. It will do backups much faster with a direct wired connection to the TC.. but not if it goes via a slow (10/100 port) on the router the ISP supplies.
5. Sparsebundle is how the TM packages the backup on network drives.
Read the info in Pondini to understand.
http://pondini.org/TM/Works.html
In particular the part about network backups.
http://pondini.org/TM/Works3.html
So you're saying that the New Time Capsule is receiving the copied file via network? No cables used in the copying to the new Time Capsule/Time Machine?
Backup runs over either wireless (slow) or ethernet (fast) to network drive.. or you can use a local disk as you have been doing.. and that is the fastest.

Need help with new Time Capsule/Airport express setup!

Similar Messages

Maybe you are looking for