Need help with opening ports on airport extreme

My vonage phone is connected to airport extreme router, voice quality of phone calls was poor. Vonage tech support says vonage port on my airport extreme was closed and i need to open it.
Here is my chat details with vonage tech support-
The following ports are needed for Internet communication between the Vonage adapters and the Vonage servers.
SIP: Port 5061 UDP
RTP (Voice) Traffic: Ports 10000-20000 UDP. When a call is made, a random port between 10000 and 20000 is used for RTP (Voice) traffic. If any of these ports are blocked, you may experience one way or no audio.
Please do suggest me the way to open the ports on airport extreme
Thanks
Venki

Instructions for opening ports is here.
https://discussions.apple.com/docs/DOC-3415
You should be fine opening the whole range, 10000-20000

Similar Messages

Need Help with 5 Port Switch, Airport Express, and wired iMac

I recently purchased an airport express to accomodate my laptop's wireless capabilities. However, the airport express has only one ethernet port, as does my parents' modem. Thus, I could either hook up the airport or my parent's iMac. I chose the airport, which resulted in a few weeks worth of fights. To alleviate the problem, I purchased a linksys 5 port group switch, after someone told me I could use that to hook up both at the same time. Initially, the iMac wouldn't work. It registered what I was told was an invalid IP address. Then a cable technician came by, reset the modem (unplugged the battery), and now the airport does not work; it flashes yellow and says that it cannot detect the ethernet signal.
The iMac is running OSX 10.3 and the laptop OSX 10.4. I am not sure if the modem can only accomodate one IP address or if there is any way to share IP addresses. Do I need to change something with the DHCP on my laptop? Do I need to manually enter an IP? Any help would be greatly appreciated. I'm completely lost....and without wireless internet.

Instead of a switch you need a wireless router, because your modem will only assign one public ip address to the switch and that ip address will be forwarded to any one computer at a given time...You should replace the switch with a wireless router and it should resolve your concern...

Open port in airport extreme for Amule

I need help with this issue because I get an Low ID when i open Amule. I know its needed to open ports TCP 4662 and UDP 4672 in Airporte Extreme mapping ports but Im not sure what exactly I have to do. I hope for any help.
Thanks

I think you need to provide more information about what you've done and what you're trying to do.
Did you assign a static LAN IP address to the NAS, what are your port forwarding entries, etc?

Need help with new Time Capsule/Airport express setup!

I just hooked up a 500g time capsule to replace an airport extreme, and now my airport utility on my MacbookPro Retina no longer recognizes the airport expresses I had on my network for airplay purposes. Can anyone help with this issue?

Instead of a switch you need a wireless router, because your modem will only assign one public ip address to the switch and that ip address will be forwarded to any one computer at a given time...You should replace the switch with a wireless router and it should resolve your concern...

Cannot open port through Airport Extreme to access security system DVR

I have internet access through Bellsouth DSL -- modem only. We had a security system set up around a DVR recording images and connected to the internet through a Linksys router. We would use a client on outside computers to connect to the security system dvr and see what was happening (live or recorded). I switched out the Linksys for the Airport Extreme, and now we cannot connect to the DVR.
Do I need to manually open a port to the DVR? How do I do this? The DVR connects to the Airport Extreme via Ethernet, and as far as I can tell, the Airport Extreme connects to the DSL modem via Ethernet using DHCP. We have a static IP address. I thank you in advance for any answers, and I apologize if I'm not giving enough information.

Let's double-check your Port Mapping setup on the 802.11n AirPort Extreme Base Station (AEBSn) ...
To setup port mapping on an 802.11n AirPort Extreme Base Station (AEBSn), either connect to the AEBSn's wireless network or temporarily connect directly, using an Ethernet cable, to one of the LAN port of the AEBSn, and then use the AirPort Utility, in Manual Setup, to make these settings:
1. Reserve a DHCP-provided IP address for the host device.
Internet > DHCP tab
o On the DHCP tab, click the "+" (Add) button to enter DHCP Reservations.
o Description: <enter the desired description of the host device>
o Reserve address by: MAC Address
o Click Continue.
o MAC Address: <enter the MAC (what Apple calls Ethernet ID if you are using wired or AirPort ID if wireless) hardware address of the host computer>
o IPv4 Address: 10.0.1.4
o Click Done.
2. Setup Port Mapping on the AEBSn.
Advanced > Port Mapping tab
o Click the "+" (Add) button
o Service: <choose the appropriate service from the Service pop-up menu>
o Public UDP Port(s): 6746
o Public TCP Port(s): 6746
o Private IP Address: 10.0.1.4
o Private UDP Port(s): 6746
o Private TCP Port(s): 6746
o Click "Continue"

Help with a 3rd party airport extreme card

I have a G4 power mac running 10.3.9. I purchased the following 3rd party card on ebay:
- Truly Plug & Play - NO complicated software CD setup at all.
- Uses Airport Drivers built into MAC OS X
- Amazing 802.11g 54Mbps Wireless - Airport Extreme speed
- Range: 50' Indoors, 150' outdoors (maximum range in ideal conditions).
- Supports WPA (TKIP,AES),802.1x and standard 128/64-bit WEP Wireless Security
- Fully Compatible with: Apple Power Macintosh G3 (Blue & White), G4 Power Mac (all models except Cube) or G5 (tower, PCI model only) computers, with a spare PCI slot, running Mac OS X 10.2.6 with AirPort installer, or Mac OS X 10.3 Panther, 10.4 Tiger & 10.5 Leopard.
Installed the card in an open slot and Airport setup assistant does not find it. The lights on the card are dark and it just is not working. So far the seller has not responded to my emails. Does anyone have any ideas what I can do to get this thing running? Thanks

What model G4. You need to add this info to your Apple Discussions profile.
What is the make/model of the Airport card?
 Cheers, Tom

Help with opening ports on the Time Capsule

Ok, let me try to describe the situation I'm in. I use a local internet company and I have 2 computers hooked up to my TC, one being a mac and the other a PC. I use the mac for office stuff and my PC is for gaming. I just bought Call of Duty: Modern Warfare 2, and it won't allow me to connect, but I when I try connecting using a Sprint Smartview internet chip, it works but goes slow. So I know it has to do with the TC, now my Mac uses the Ip 10.0.1.201 and my PC is 10.0.1.4, I've tried opening up the ports with the port mapping tool in Airport Utilities but didn't have any luck. I don't want to ruin anything by wandering into things I don't understand ...
The ports needed are on this website
http://forums.steampowered.com/forums/showthread.php?t=1019454
Thanks in advance, I've been trying to figure this out for the last like 6 hours!

Ok, let me try to describe the situation I'm in. I use a local internet company and I have 2 computers hooked up to my TC, one being a mac and the other a PC. I use the mac for office stuff and my PC is for gaming. I just bought Call of Duty: Modern Warfare 2, and it won't allow me to connect, but I when I try connecting using a Sprint Smartview internet chip, it works but goes slow. So I know it has to do with the TC, now my Mac uses the Ip 10.0.1.201 and my PC is 10.0.1.4, I've tried opening up the ports with the port mapping tool in Airport Utilities but didn't have any luck. I don't want to ruin anything by wandering into things I don't understand ...
The ports needed are on this website
http://forums.steampowered.com/forums/showthread.php?t=1019454
Thanks in advance, I've been trying to figure this out for the last like 6 hours!

Need help creating network of 1 Airport Extreme & 2 Airport Expresses!

Please somebody help me! I've literally been trying to get our home network to function for months now. I'm seriously about to cry if i can't make it work.
Here's the situation:
Our apartment is long and narrow and probably has lead paint, so our wifi, powered by a brand new Airport Extreme Base Station 802.11n router (named Igor) connected to a comcast modem doesn't reach the whole house. So we got 2 Airport Expresses to place throughout the apartment (named Sven and Svetlana) to help boost the signal.
First i tried to set up Igor to 'Create a wireless network" with the option 'allow this network to be extended' and the connection sharing set to 'Share a public IP' and i set up Sven and Svetlana to 'extend a wireless network' and the connection sharing was set to 'share a public IP'. Everything else was automatic or default pretty much. I got it to work but the connection was really weak and dropped out a lot.
Then i tried setting up a WDS network. no luck there either. so i went to the apple store and they told me i had to hard wire them all together using ethernet cables (roaming network i guess) to compensate for the ****** network acoustics in our place.
So...i ran 1 ethernet cable from Igor down the hall to Svetlana and another from Igor further down the hall to Sven. I set up all 3 to 'create a wireless network' and gave them all the same network name and password. i left the 'allow this network to be extended' option unchecked on all 3 and put them all in bridge mode and automatic settings for the radio mode and channel selection. After about 50 restarts i finally got it to work. Things seemed great for a minute until i realized that my laptop was the only one in the house that could connect to the internet. When i tried to troubleshoot the problem using network diagnostics and restarts, i eventually got my roommate's laptop to work but then mine stopped working.
i've tried changing Igor's connection setting to share a public IP address and leaving Sven and Svetlana's in bridge mode. I've tried changing the 'configure IPv4' setting from 'using DHCP' to 'manual' and entering in identical info for all 3 in the TCP/IP section.
no matter what i do i still have no idea how to make this work for multiple devices in our apartment. I really don't understand that much about networking but i am great at following directions. Please please please please help me! I'm desperate.
thank you in advance for your help!
ilana

So...i ran 1 ethernet cable from Igor down the hall to Svetlana and another from Igor further down the hall to Sven. I set up all 3 to 'create a wireless network' and gave them all the same network name and password. i left the 'allow this network to be extended' option unchecked on all 3 and put them all in bridge mode and automatic settings for the radio mode and channel selection.
In a "roaming" network, the router connected to the Internet modem should NOT be in bridge mode. In this case that would be your 802.11n AirPort Extreme Base Station (AEBSn). That is because you want it to provide both NAT & DHCP services to both AirPort Express Base Stations and the network clients.

Open ports on airport extreme

How can I open port 3389 on airport extreme/time capsule?

Suggest that you take a look at this User Tip......provided by forum expert Tesserax......to get started on the basics of port mapping:
AirPort - Port Mapping Basics using AirPort Utility v6.x

Need help with open hub

Hi eveybody,
I was trying to wok with open hub. Created infospoke, destination i gave was a csv file named d:/openmara.csv path, saved and activated the info spoke. I went to d:/ to view the uploaded files, two file was created, when i try to open a file it says "unable to read" , when i tried to open the second one i could open the file and see some datas but not in a correct format, why is that?
Then i tried to load the data in database, so in the infospoke i selected the option for destination as database,saved and activated the infospoke, now where should i go to see the uploaded datas physically?
Could anyone help me with this.
Thanks,
RR.

Hi,
Thanks for the reply. I created a infospoke and destination was database option. Opened the se16 gave the table name which starts with /bic/....(please correct me if i am wrong),then the initial screen of se16 came up with all the fields , but when i executed it, the table is empty.Could you say why it is happening.
Thanks,
RR.

Need help with bus ports (pre or post?)

I have recorded my acoustic guitar on two tracks in order to save time with the drop region and cutting and I have already autonated both of the tracks so they sound like one guitar (same channel strips).
However, I am trying not to use the plug ins that are on the guitar tracks TWICE (they are verry powerful), so I would like to copy the channel strip of my guitar tracks to a bus track, yet still keep the autonation working for both tracks (by the way, its just volume after the plug ins).
I cant say I could esily put all the regions from both tracks into one, so I want to use a bus.
If this is at all possibe for me to do while keeping my automation for both of the two tracks, how would I go about doing this? (do I set them as pre/post sends, ect.)
Thank you so much!
-Sam

Instructions for opening ports is here.
https://discussions.apple.com/docs/DOC-3415
You should be fine opening the whole range, 10000-20000

Help with opening port 10000 on a pix 501

I am attempting to open port 10000 so that I can remotely VPN using tcp port 10000. This is a pix 501 running version 6.3.5.
What commands do I need to enter for this to happen?

Remote vpn access can be configured on a pix 501 by using the configuration guide present in the links given below:
Site-to-Site VPN Configuration Examples is present in the url below:
http://www.cisco.com/en/US/docs/security/pix/pix63/configuration/guide/sit2site.html
Managing VPN Remote Access giude is present in the following url:
http://www.cisco.com/en/US/docs/security/pix/pix63/configuration/guide/basclnt.html

I need help with opening attachment on email?

I need help to set association to open attachment on email?

First i would suggest update Reader to XI.
To set the default application you may visit this article: http://windows.microsoft.com/en-in/windows/change-default-programs#1TC=windows-7 this article is for windows 7 but it will hold good for vista too.
let me know the result.
~Ajlan Huda.

Need help with opening DatagramSocket

Hello I want to make a socket connection this is my code
public void run()
int s=0;
MakeConnection(s);
In MakeConnection I have thisvoid MakeConnection(int s) throws IOException
int port =1234;
DatagramSocket client = new DatagramSocket(port);
When I compile this code this is said
unreported exception java.io.IOException; must be caught or declared to be thrown.
Can anyone help me with this fault.
And is it possible to get
int s = client;
Because when I do it with c I can do
int s;
s = socket(AF_INET,SOCK_DGRAM,IPPROTO_UDP);
en than s is 10 on my computer and in my java code I need to receive s=10 too.

Do you know what exceptions are? If not, read about them in the Java Tutorial:
http://java.sun.com/docs/books/tutorial/essential/exceptions/index.html
In the method run(), you call the method MakeConnection(), which might throw an IOException.
Since IOException is a checked exception, you must in the method run() specify what you're going to do when an IOException happens. You must either catch the exception (put the call to MakeConnection in a try / catch block) or indicate that run() can throw an IOException by specifying it at the beginning of the method:
public void run() throws IOException { ...
But note that you'll just be moving the problem to the method that calls run(). Somewhere in your program you must catch and handle the exception.

Re: Need help with open a web page

Dear friend i cant open www.truperenlinea.com maybe you can support me because i install IE but other 5.2 version,
i dont want install parallel and Windows, you can try to open for me and explain me.
See the right side in the web need can see the username and password space to fill.
Thank you so much
Best regards

Sorry, I got confused.
You need to stick you your original post.
Please don't post in someone elses thread, especially when the thread is completely in the wrong place to begin with and you post has nothing to do with the original post.

Need help with opening ports on airport extreme

Similar Messages

Maybe you are looking for